scholarly journals Improvement and Validation of Ranging Accuracy with YG-13A

2017 ◽  
Author(s):  
Mingjun Deng ◽  
Guo Zhang ◽  
Ruishan Zhao ◽  
Jiansong Li ◽  
Jiansong Li
Keyword(s):  
Target Location ◽  
Single Frequency ◽  
Path Delay ◽  
Gps Receiver ◽  
Dual Frequency ◽  
Error Sources ◽  
Correction Model ◽  
Pixel Location ◽  
Atmospheric Path ◽  
Set Up

YG-13A represents the highest level of Chinese SAR satellites to date. In this paper, we report on experiments conducted to improve and validate ranging accuracy with YG-13A. We analyze the error sources in the YG-13A ranging system, such as atmospheric path delay, and transceiver channel delay. A real-time atmospheric delay correction model is established to calculate the atmospheric path delay, considering the troposphere delay and ionosphere delay. Six corner reflectors (CRs) were set up to ensure the accuracy of validation methods. Pixel location accuracies of up to 0.479-m standard deviation can be achieved after a complete calibration. We further demonstrate that the adjustment of the CRs can cause a marginal loss of ranging precision. After eliminating this error, the ranging accuracy is improved to 0.237 m. For YG-13A, a single frequency GPS receiver is used and the orbital nominal accuracy is 0.3 m, which is the biggest factor restricting its ranging accuracy. Our results show that the ranging accuracy of YG-13A can achieve decimeter-level, which is lower than centimeter-level accuracy with TerraSAR-X loading a dual frequency GPS. YG-13A has great convenience in terms of access to control points and target location that does not depend on ground equipment.

scholarly journals Assessing the quality of ionospheric models through GNSS positioning error: methodology and results

GPS Solutions ◽  
2019 ◽  
Vol 24 (1) ◽  
Author(s):  
Adrià Rovira-Garcia ◽  
Deimos Ibáñez-Segura ◽  
Raul Orús-Perez ◽  
José Miguel Juan ◽  
Jaume Sanz ◽  
...  
Keyword(s):  
Satellite System ◽  
Ionospheric Delay ◽  
Single Frequency ◽  
Positioning Error ◽  
Dual Frequency ◽  
Error Sources ◽  
Ionospheric Models ◽  
Evaluation Metric ◽  
Global Navigation Satellite

Abstract Single-frequency users of the global navigation satellite system (GNSS) must correct for the ionospheric delay. These corrections are available from global ionospheric models (GIMs). Therefore, the accuracy of the GIM is important because the unmodeled or incorrectly part of ionospheric delay contributes to the positioning error of GNSS-based positioning. However, the positioning error of receivers located at known coordinates can be used to infer the accuracy of GIMs in a simple manner. This is why assessment of GIMs by means of the position domain is often used as an alternative to assessments in the ionospheric delay domain. The latter method requires accurate reference ionospheric values obtained from a network solution and complex geodetic modeling. However, evaluations using the positioning error method present several difficulties, as evidenced in recent works, that can lead to inconsistent results compared to the tests using the ionospheric delay domain. We analyze the reasons why such inconsistencies occur, applying both methodologies. We have computed the position of 34 permanent stations for the entire year of 2014 within the last Solar Maximum. The positioning tests have been done using code pseudoranges and carrier-phase leveled (CCL) measurements. We identify the error sources that make it difficult to distinguish the part of the positioning error that is attributable to the ionospheric correction: the measurement noise, pseudorange multipath, evaluation metric, and outliers. Once these error sources are considered, we obtain equivalent results to those found in the ionospheric delay domain assessments. Accurate GIMs can provide single-frequency navigation positioning at the decimeter level using CCL measurements and better positions than those obtained using the dual-frequency ionospheric-free combination of pseudoranges. Finally, some recommendations are provided for further studies of ionospheric models using the position domain method.

scholarly journals Impact of Approximate Implementation manner in Klobuchar Model

2021 ◽  
Vol 64 (4) ◽  
pp. RS440
Author(s):  
Aghyas Aljuneidi ◽  
Hala Tawfek Hasan
Keyword(s):  
Single Frequency ◽  
Gps Receiver ◽  
Reference Field ◽  
International Geomagnetic Reference Field ◽  
Ionospheric Correction ◽  
Correction Model ◽  
Klobuchar Model ◽  
Magnetic Model ◽  
Implementation In Matlab ◽  
Made In

This paper focuses on the approximations that John A. Klobuchar made in mid 70s in his famous algorithm of ionospheric correction model for single frequency GPS receiver. At that time Klobuchar used a system of fixed geomagnetic north pole coordinates which are not accurate nowadays according to the International Geomagnetic Reference Field and to the World Magnetic Model because the geomagnetic poles move slowly. In addition, Klobuchar had to do other trigonometry simplifications in his implementation to avoid sophisticated computations. In order to evaluate this approximate implementation in a single frequency GPS receiver, ionospheric time and range delay are estimated on the entire day of January 1st 2010, using a different implementation in MATLAB. The required GPS data is obtained from recorded RINEX files at UDMC near DAMASCUS, SYRIA. In this comparative study, we reformulated the standard equations of Klobuchar model and examined the influence of its approximations on the ionospheric range delay and found a non- negligible bias in order of ten centimeters, whereas the influence of the movement of the geomagnetic poles was in order of few centimeters.

Investigation of a L1-optimized choke ring ground plane for a low-cost GPS receiver-system

2018 ◽  
Vol 12 (1) ◽  
pp. 55-64
Author(s):  
Li Zhang ◽  
Volker Schwieger
Keyword(s):  
Low Cost ◽  
Ground Plane ◽  
Single Frequency ◽  
Limiting Factor ◽  
Test Field ◽  
Gps Receiver ◽  
Dual Frequency ◽  
Multipath Effect ◽  
Receiver System ◽  
Multipath Signal

AbstractBesides the geodetic dual-frequency GNSS receivers-systems (receiver and antenna), there are also low-cost single-frequency GPS receiver-systems.The multipath effect is a limiting factor of accuracy for both geodetic dual-frequency and low-cost single-frequency GPS receivers. And the multipath effect is for the short baselines dominating error (typical for the monitoring in Engineering Geodesy). So accuracy and reliability of GPS measurement for monitoring can be improved by reducing the multipath signal.In this paper, the self-constructed L1-optimized choke ring ground plane (CR-GP) is applied to reduce the multipath signal. Its design will be described and its performance will be investigated.The results show that the introduced low-cost single-frequency GPS receiver-system, which contains the Ublox LEA-6T single-frequency GPS receiver and Trimble Bullet III antenna with a self-constructed L1-optimized CR-GP, can reach standard deviations of 3 mm in east, 5 mm in north and 9 mm in height in the test field which has many reflectors. This accuracy is comparable with the geodetic dual-frequency GNSS receiver-system. The improvement of the standard deviation of the measurement using the CR-GP is about 50 % and 35 % compared to the used antenna without shielding and with flat ground plane respectively.

scholarly journals A Dual Frequency Ultrasonic Cleaning Tank Developed by Transient Dynamic Analysis

2021 ◽  
Vol 11 (2) ◽  
pp. 699
Author(s):  
Worapol Tangsopa ◽  
Jatuporn Thongsri
Keyword(s):  
High Performance ◽  
Acoustic Pressure ◽  
Single Frequency ◽  
Response Analysis ◽  
Dual Frequency ◽  
Transient Dynamic Analysis ◽  
Ultrasonic Cleaning ◽  
Calculational Method ◽  
Successful Design ◽  
Harmonic Response Analysis

At present, development of manufacturer’s ultrasonic cleaning tank (UCT) to match the requirements from consumers usually relies on computer simulation based on harmonic response analysis (HRA). However, this technique can only be used with single-frequency UCT. For dual frequency, the manufacturer used information from empirical experiment alongside trial-and-error methods to develop prototypes, resulting in the UCT that may not be fully efficient. Thus, lack of such a proper calculational method to develop the dual frequency UCT was a problem that greatly impacted the manufacturers and consumers. To resolve this problem, we proposed a new model of simulation using transient dynamics analysis (TDA) which was successfully applied to develop the prototype of dual frequency UCT, 400 W, 18 L in capacity, eight horn transducers, 28 and 40 kHz frequencies for manufacturing. The TDA can indicate the acoustic pressure at all positions inside the UCT in transient states from the start to the states ready for proper cleaning. The calculation also reveals the correlation between the positions of acoustic pressure and the placement positions of transducers and frequencies. In comparison with the HRA at 28 kHz UCT, this TDA yielded the results more accurately than the HRA simulation, comparing to the experiments. Furthermore, the TDA can also be applied to the multifrequency UCTs as well. In this article, the step-by-step development of methodology was reported. Finally, this simulation can lead to the successful design of the high-performance dual frequencies UCT for the manufacturers.

scholarly journals Precise Point Positioning Using Dual-Frequency GNSS Observations on Smartphone

Sensors ◽  
2019 ◽  
Vol 19 (9) ◽  
pp. 2189 ◽  
Author(s):  
Qiong Wu ◽  
Mengfei Sun ◽  
Changjie Zhou ◽  
Peng Zhang
Keyword(s):  
Precise Point Positioning ◽  
Frequency Mode ◽  
Single Frequency ◽  
Dual Frequency ◽  
Static Mode ◽  
Position Errors ◽  
Point Positioning ◽  
Similar Accuracy ◽  
Positioning Algorithm ◽  
Gnss Observations

The update of the Android system and the emergence of the dual-frequency GNSS chips enable smartphones to acquire dual-frequency GNSS observations. In this paper, the GPS L1/L5 and Galileo E1/E5a dual-frequency PPP (precise point positioning) algorithm based on RTKLIB and GAMP was applied to analyze the positioning performance of the Xiaomi Mi 8 dual-frequency smartphone in static and kinematic modes. The results showed that in the static mode, the RMS position errors of the dual-frequency smartphone PPP solutions in the E, N, and U directions were 21.8 cm, 4.1 cm, and 11.0 cm, respectively, after convergence to 1 m within 102 min. The PPP of dual-frequency smartphone showed similar accuracy with geodetic receiver in single-frequency mode, while geodetic receiver in dual-frequency mode has higher accuracy. In the kinematic mode, the positioning track of the smartphone dual-frequency data had severe fluctuations, the positioning tracks derived from the smartphone and the geodetic receiver showed approximately difference of 3–5 m.

scholarly journals High-precision coseismic displacement estimation with a single-frequency GPS receiver

2015 ◽  
Vol 202 (1) ◽  
pp. 612-623 ◽  
Author(s):  
Bofeng Guo ◽  
Xiaohong Zhang ◽  
Xiaodong Ren ◽  
Xingxing Li
Keyword(s):  
High Precision ◽  
Single Frequency ◽  
Gps Receiver ◽  
Coseismic Displacement ◽  
Displacement Estimation

scholarly journals A Robust Dual-Frequency Radar Profiling Algorithm

2011 ◽  
Vol 50 (7) ◽  
pp. 1543-1557 ◽  
Author(s):  
Mircea Grecu ◽  
Lin Tian ◽  
William S. Olson ◽  
Simone Tanelli
Keyword(s):  
Synthetic Data ◽  
Optimization Procedure ◽  
Correction Method ◽  
Single Frequency ◽  
Retrieval Algorithm ◽  
Dual Frequency ◽  
Ka Band ◽  
Radar Observations ◽  
Distribution Shape ◽  
Ku Band

AbstractIn this study, an algorithm to retrieve precipitation from spaceborne dual-frequency (13.8 and 35.6 GHz, or Ku/Ka band) radar observations is formulated and investigated. Such algorithms will be of paramount importance in deriving radar-based and combined radar–radiometer precipitation estimates from observations provided by the forthcoming NASA Global Precipitation Measurement (GPM) mission. In GPM, dual-frequency Ku-/Ka-band radar observations will be available only within a narrow swath (approximately one-half of the width of the Ku-band radar swath) over the earth’s surface. Therefore, a particular challenge is to develop a flexible radar retrieval algorithm that can be used to derive physically consistent precipitation profile estimates across the radar swath irrespective of the availability of Ka-band radar observations at any specific location inside that swath, in other words, an algorithm capable of exploiting the information provided by dual-frequency measurements but robust in the absence of Ka-band channel. In the present study, a unified, robust precipitation retrieval algorithm able to interpret either Ku-only or dual-frequency Ku-/Ka-band radar observations in a manner consistent with the information content of the observations is formulated. The formulation is based on 1) a generalized Hitschfeld–Bordan attenuation correction method that yields generic Ku-only precipitation profile estimates and 2) an optimization procedure that adjusts the Ku-band estimates to be physically consistent with coincident Ka-band reflectivity observations and surface reference technique–based path-integrated attenuation estimates at both Ku and Ka bands. The algorithm is investigated using synthetic and actual airborne radar observations collected in the NASA Tropical Composition, Cloud, and Climate Coupling (TC4) campaign. In the synthetic data investigation, the dual-frequency algorithm performed significantly better than a single-frequency algorithm; dual-frequency estimates, however, are still sensitive to various assumptions such as the particle size distribution shape, vertical and cloud water distributions, and scattering properties of the ice-phase precipitation.

scholarly journals Validation of GPM Rainfall and Drop Size Distribution Products through Disdrometers in Italy

2021 ◽  
Vol 13 (11) ◽  
pp. 2081
Author(s):  
Elisa Adirosi ◽  
Mario Montopoli ◽  
Alessandro Bracci ◽  
Federico Porcù ◽  
Vincenzo Capozzi ◽  
...  
Keyword(s):  
Size Distribution ◽  
Drop Size ◽  
Global Scale ◽  
Drop Size Distribution ◽  
Single Frequency ◽  
Dual Frequency ◽  
Near Surface ◽  
Active Sensor ◽  
Long Time ◽  
Global Precipitation

The high relevance of satellites for collecting information regarding precipitation at global scale implies the need of a continuous validation of satellite products to ensure good data quality over time and to provide feedback for updating and improving retrieval algorithms. However, validating satellite products using measurements collected by sensors at ground is still a challenging task. To date, the Dual-frequency Precipitation Radar (DPR) aboard the Core Satellite of the Global Precipitation Measurement (GPM) mission is the only active sensor able to provide, at global scale, vertical profiles of rainfall rate, radar reflectivity, and Drop Size Distribution (DSD) parameters from space. In this study, we compare near surface GPM retrievals with long time series of measurements collected by seven laser disdrometers in Italy since the launch of the GPM mission. The comparison shows limited differences in the performances of the different GPM algorithms, be they dual- or single-frequency, although in most cases, the dual-frequency algorithms present the better performances. Furthermore, the agreement between satellite and ground-based estimates depends on the considered precipitation variable. The agreement is very promising for rain rate, reflectivity factor, and the mass-weighted mean diameter (Dm), while the satellite retrievals need to be improved for the normalized gamma DSD intercept parameter (Nw).

Sign in / Sign up

Export Citation Format

Share Document