scholarly journals ESTUDIO DE LA RESISTENCIA A LA CORROSION DEL ALUMINIO 6063 ANODIZADO

2017 ◽  
Vol 22 (2) ◽  
pp. 17
Author(s):  
Karín Paucar Cuba ◽  
Hugo Rojas Flores ◽  
Abel Vergara Sotomayor
Keyword(s):  
Corrosion Resistance ◽  
Aluminum Alloy ◽  
Sulfuric Acid ◽  
Electrochemical Impedance ◽  
Salt Spray ◽  
Aluminum Surface ◽  
Equivalent Circuits ◽  
Acid Salt ◽  
Mass Losses ◽  
Palabras Clave

El estudio de la resistencia a la corrosión del anodizado de una aleación de aluminio (AA6063) en ácido sulfúrico a diferentes tiempos de anodizado: 30, 45 y 60 min. se realizó usando la espectroscopia de impedancia electroquímica (EIE) y el ensayo de niebla salina ácida. (ASTM B287). Los datos obtenidos por EIE y su correlación con los circuitos equivalentes más apropiados permitieron determinar los parámetros asociados a la capa porosa y a la capa barrera del óxido protector formado sobre la superficie del aluminio en estudio. La exposición de las muestras anodizadas durante 250h a una niebla salina ácida permitió observar variaciones en su masa. De los resultados obtenidos por EIE y las pérdidas de masa de las muestras anodizadas se estableció que la película de anodizado de 45 minutos mostró una mayor resistencia a la corrosión en comparación con la obtenida a 60 y 30 min., respectivamente. Palabras clave.- Aluminio, Anodizado, Impedancia electroquímica, Niebla salina ácida. ABSTRACTThe study of the corrosion resistance of anodized on aluminum alloy (AA6063) in sulfuric acid to different times: 30, 45 and 60 min. was performed using electrochemical impedance spectroscopy (EIS) and the acid salt spray test (ASTM B287). The EIS’data and its correlation with the most appropriate equivalent circuits allowed to determine the parameters associated with the porous layer and the oxide layer protective barrier formed on the aluminum surface under study. Exposure of the samples anodized for a 250h salt spray acid allowed to observe changes in their mass. From the results obtained by EIS and the mass losses of the anodized samples was established that the anodized film of 45 minutes showed higher corrosion resistance compared to that obtained at 60 and 30 min, respectively. Keywords.- Aluminum, Anodized, Electrochemical impedance, Acid salt spray.

Salt spray corrosion and electrochemical corrosion property of anodic oxide films on ADC12 aluminum alloy

2021 ◽  
Author(s):  
Naizhi Liu ◽  
Bo Jiang ◽  
Zesheng Ji ◽  
Pengxing Cui ◽  
Yunlong Wang ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Aluminum Alloy ◽  
Electrochemical Impedance ◽  
Salt Spray ◽  
Oxide Films ◽  
Electrochemical Corrosion ◽  
Anodic Oxide ◽  
Positive Direction ◽  
Salt Spray Corrosion ◽  
Anodic Oxide Films

Anodic oxide films were prepared by anodic oxidation on the surface of ADC12 aluminum alloy and their corrosion properties were explored. The original samples, anodized samples, and sealed samples were placed in the salt spray corrosion chamber and were taken out at different times. Then the corrosion resistance of the ADC12 aluminum alloy was discussed, and the electrochemical corrosion test was researched. The results indicated that the surface of the original samples reveals many large-area pits after salt spray corrosion, while the sealed samples present a smoother surface. The dense oxide films on the surface of the base metals effectively prevent Cl[Formula: see text] entering into aluminum alloys especially after sealing. Electrochemical tests including the potential polarization curve and electrochemical impedance spectroscopy (EIS) as functions of exposure time were employed to reveal the corrosion behavior of surface layers. After the sealing treatment on the oxide films, the corrosion potential moved in the positive direction, the corrosion current density decreased, and the corrosion resistance of the ADC12 aluminum alloy was significantly improved.

scholarly journals Hydrophobic Modification of Graphene Oxide and Its Effect on the Corrosion Resistance of Silicone-Modified Epoxy Resin

Metals ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 89
Author(s):  
Wei Yuan ◽  
Qian Hu ◽  
Jiao Zhang ◽  
Feng Huang ◽  
Jing Liu
Keyword(s):  
Contact Angle ◽  
Corrosion Resistance ◽  
Graphene Oxide ◽  
Physical Properties ◽  
Epoxy Resin ◽  
Electrochemical Impedance ◽  
Salt Spray ◽  
X Ray ◽  
Modified Graphene Oxide ◽  
Modified Epoxy

This study modified graphene oxide (GO) with hydrophilic octadecylamine (ODA) via covalent bonding to improve its dispersion in silicone-modified epoxy resin (SMER) coatings. The structural and physical properties of ODA-GO were characterized by field-emission scanning electron microscopy (FE-SEM), X-ray diffraction analysis (XRD), Fourier transform infrared spectroscopy (FT-IR), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), and contact angle tests. The ODA-GO composite materials were added to SMER coatings by physical mixing. FE-SEM, water absorption, and contact angle tests were used to evaluate the physical properties of the ODA-GO/SMER coatings, while salt spray, electrochemical impedance spectroscopy (EIS), and scanning Kelvin probe (SKP) methods were used to test the anticorrosive performance of ODA-GO/SMER composite coatings on Q235 steel substrates. It was found that ODA was successfully grafted onto the surfaces of GO. The resulting ODA-GO material exhibited good hydrophobicity and dispersion in SMER coatings. The anticorrosive properties of the ODA-GO/SMER coatings were significantly improved due to the increased interfacial adhesion between the nanosheets and SMER, lengthening of the corrosive solution diffusion path, and increased cathodic peeling resistance. The 1 wt.% ODA-GO/SMER coating provided the best corrosion resistance than SMER coatings with other amounts of ODA-GO (including no addition). After immersion in 3.5 wt.% NaCl solution for 28 days, the low-frequency end impedance value of the 1 wt.% ODA-GO/SMER coating remained high, at 6.2 × 108 Ω·cm2.

scholarly journals Design and Multidimensional Screening of Flash-PEO Coatings for Mg in Comparison to Commercial Chromium(VI) Conversion Coating

Metals ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 337
Author(s):  
Ewa Wierzbicka ◽  
Marta Mohedano ◽  
Endzhe Matykina ◽  
Raul Arrabal
Keyword(s):  
Corrosion Resistance ◽  
Corrosion Protection ◽  
Electrochemical Impedance ◽  
Salt Spray ◽  
Conversion Coating ◽  
Neutral Salt ◽  
Chromium Vi ◽  
Alkaline Electrolytes ◽  
Az31b Alloy ◽  
Plasma Electrolytic

REACH (Registration, Evaluation, Authorisation and Restriction of Chemicals) regulations demand for an expedient discovery of a Cr(VI)-free alternative corrosion protection for light alloys even though the green alternatives might never be as cheap as current harmful technologies. In the present work, flash- plasma electrolytic oxidation coatings (FPEO) with the process duration < 90 s are developed on AZ31B alloy in varied mixtures of silicate-, phosphate-, aluminate-, and fluoride-based alkaline electrolytes implementing current density and voltage limits. The overall evaluation of the coatings’ anticorrosion performance (electrochemical impedance spectroscopy (EIS), neutral salt spray test (NSST), paintability) shows that from nine optimized FPEO recipes, two (based on phosphate, fluoride, and aluminate or silicate mixtures) are found to be an adequate substitute for commercially used Cr(VI)-based conversion coating (CCC). The FPEO coatings with the best corrosion resistance consume a very low amount of energy (~1 kW h m−2 µm−1). It is also found that the lower the energy consumption of the FPEO process, the better the corrosion resistance of the resultant coating. The superb corrosion protection and a solid environmentally friendly outlook of PEO-based corrosion protection technology may facilitate the economic justification for industrial end-users of the current-consuming process as a replacement of the electroless CCC process.

scholarly journals Surface Modification of Aluminum 6061-O Alloy by Plasma Electrolytic Oxidation to Improve Corrosion Resistance Properties

Coatings ◽  
2020 ◽  
Vol 11 (1) ◽  
pp. 4
Author(s):  
Dmitry V. Dzhurinskiy ◽  
Stanislav S. Dautov ◽  
Petr G. Shornikov ◽  
Iskander Sh. Akhatov
Keyword(s):  
Corrosion Resistance ◽  
Aluminum Alloy ◽  
Aluminum Alloys ◽  
Plasma Electrolytic Oxidation ◽  
Electrochemical Impedance ◽  
High Strength ◽  
Electrolytic Oxidation ◽  
Coating Layers ◽  
Plasma Electrolytic ◽  
High Strength Aluminum Alloys

In the present investigation, the plasma electrolytic oxidation (PEO) process was employed to form aluminum oxide coating layers to enhance corrosion resistance properties of high-strength aluminum alloys. The formed protective coating layers were examined by means of scanning electron microscopy (SEM) and characterized by several electrochemical techniques, including open circuit potential (OCP), linear potentiodynamic polarization (LP) and electrochemical impedance spectroscopy (EIS). The results were reported in comparison with the bare 6061-O aluminum alloy to determine the corrosion performance of the coated 6061-O alloy. The PEO-treated aluminum alloy showed substantially higher corrosion resistance in comparison with the untreated substrate material. A relationship was found between the coating formation stage, process parameters and the thickness of the oxide-formed layers, which has a measurable influence on enhancing corrosion resistance properties. This study demonstrates promising results of utilizing PEO process to enhance corrosion resistance properties of high-strength aluminum alloys and could be recommended as a method used in industrial applications.

scholarly journals Corrosion Behavior of AA 1100 Anodized in Gallic-Sulfuric Acid Solution

Coatings ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 405
Author(s):  
Marlon L. Mopon ◽  
Jayson S. Garcia ◽  
Dexter M. Manguerra ◽  
Cyril John C. Narisma
Keyword(s):  
Corrosion Resistance ◽  
Sulfuric Acid ◽  
Acid Solution ◽  
Gallic Acid ◽  
Acid Concentration ◽  
Sulfuric Acid Solution ◽  
Current Density ◽  
Electrochemical Impedance ◽  
Anodized Aluminum ◽  
The Common

Sulfuric acid anodization is one of the common methods used to improve corrosion resistance of aluminum alloys. Organic acids can be added to the sulfuric acid electrolyte in order to improve the properties of the anodized aluminum produced. In this study, the use of gallic acid as an additive to the sulfuric acid anodization of AA1100 was explored. The effect of varying anodization current density and gallic acid concentration on the properties of anodized aluminum samples was observed using electrochemical impedance spectroscopy, linear polarization, and scanning electron microscopy. It was observed that the corrosion resistance of samples anodized in gallic-sulfuric acid solution at 10 mA·cm−2 is lower than samples anodized in sulfuric acid. It was also observed that higher anodization current density can lead to lower corrosion resistances for aluminum samples anodized in gallic-sulfuric acid solution. However, samples anodized at 5 mA·cm−2 and at a gallic acid concentration of 5 g·L−1 showed better corrosion performance than the samples anodized in sulfuric acid only. This suggests that the use of low amounts of gallic acid as an additive for sulfuric acid anodization can lead to better corrosion resistances for anodized aluminum.

scholarly journals Effect of Heat Treatment and Sulfuric Acid Anodization on Corrosion Resistance of Aluminum Alloy (AA7075)

2021 ◽  
Vol 40 (1) ◽  
pp. 56-62
Author(s):  
M. Abdullahi ◽  
L.S. Kuburi ◽  
P.T. Zubairu ◽  
U. Jabo ◽  
A.A. Yahaya ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Corrosion Resistance ◽  
Aluminum Alloy ◽  
Sulfuric Acid ◽  
Corrosion Rate ◽  
Polarization Resistance ◽  
Testing Machine ◽  
Palm Kernel ◽  
Engine Oil ◽  
Micro Hardness

This paper, studied the effect of heat treatment and anodization on corrosion resistance of aluminum alloy 7075 (AA7075), with a view to improving its corrosion resistance. Microstructure and micro hardness of the anodic film of the samples were studied with the aid of optical metallurgical microscope and automated micro hardness testing machine. Linear polarization methods were used to assess the corrosion behaviour of the alloy in 0.5M HCl. The microstructure of the annealed sample showed formation of dendrites while precipitation hardened samples in palm kernel oil and SAE 40 engine oil showed precipitates of MgZn2. The SEMS result showed pores and micro cracks on the surfaces of the anodized samples, with the as cast and anodized sample in sulfuric acid exhibiting most compact with few pores. The as cast and sulfuric acid anodized sample shows highest micro hardness value of 205.33 HV, while the least value of 150.67 HV was recorded in sample precipitation hardened in SAE 40 engine oil and anodized in sulfuric acid. Analysis of the potentiodynamic polarization data and curves showed a linear relationship (decrease in icorr, decreases the corrosion rate) between current density and the corrosion rate in all the samples. Higher polarization resistance of 15.093 Ω/cm2 was recorded by the as cast and Sulfuric acid (SA) anodized sample while the precipitation treated in SAE 40 engine oil plus SA anodized sample recorded lowest polarization resistance of 5.2311 Ω/cm2. Heat treatment alone improves corrosion resistance of AA 7075 in 0.5 M HCl solution but heat treatment plus SA anodization does not improve corrosion resistance in the same environment.

Effect of narrow pulse width laser cleaning on corrosion resistance of A5083-H111 aluminum alloy

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Feisen Wang ◽  
Sifei Ai ◽  
Qian Wang ◽  
Yinfen Cheng ◽  
Haiqi Huang ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Aluminum Alloy ◽  
Surface Morphology ◽  
Elemental Composition ◽  
Pulse Width ◽  
Salt Spray ◽  
Laser Cleaning ◽  
Elemental Distribution ◽  
Content Type ◽  
Poor Area

Purpose The purpose of this paper is to promote the corrosion resistance of the 5083-111H aluminum alloy by laser cleaning. Design/methodology/approach Laser with 2 ns pulse width was adopted in this project and the corrosion resistance of cleaned samples was tested by copper-accelerated salt spray (CASS). The surface morphology, elemental composition and distribution were then characterized by SEM. Moreover, surface morphology, elemental composition and distribution were also tested. Findings Results suggested a higher corrosion resistance was successfully obtained by laser cleaning. Compared with samples cleaned by 2000 grit sandpaper, mechanical cleaning resulted in a 53% larger height difference between the peak and valley. The content of the oxygen is 8.85% on the surface cleaned mechanically and the distribution is dependent on the distribution of aluminum whereas that of the laser cleaning sample is 24.41% and the distribution existed even in the Al-poor area. Originality/value In this project, the 2-ns laser cleaning was proved to have the capability to remove the oxide layer on the aluminum alloy surface while retaining an excellent corrosion resistance and smooth surface. Meanwhile, a thorough elemental distribution and smaller grain size lead to a smaller difference in elemental concentration. This retards the diffusion of oxygen into the substrate and hence increases the corrosion resistance of the surface.

scholarly journals Enhanced Corrosion Resistance of Recycled Aluminum Alloy 6061 Chips Using Hot Extrusion Followed by ECAP

2019 ◽  
Vol 2019 ◽  
pp. 1-8 ◽  
Author(s):  
Mohamed A. Taha ◽  
Adel T. Abbas ◽  
Faycal Benyahia ◽  
Hamad F. Alharbi ◽  
B. Guitián ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Aluminum Alloy ◽  
Material Properties ◽  
Saline Solution ◽  
Electrochemical Impedance ◽  
Hot Extrusion ◽  
Ecap Process ◽  
The Cost ◽  
Alloy 6061 ◽  
Resultant Material

The oxidation of aluminum machining chips retards the successful recycling through the conventional remelting route. A promising approach to overthrow this problem is the utilization of solid state recycling in converting aluminum machining chips directly into semifinished products to eliminate the cost of the remelting process and reduce CO2 emissions. Therefore, in recent work, chips of aluminum alloy (AA6061) were recycled by compaction and then extrusion conducted at 500°C, followed by equal channel pressing (ECAP) to study the resultant material properties and its microstructure. Moreover, the present investigation explores the influence of ECAP after hot extrusion on the corrosive behaviour of the recycled samples in saline solution (NaCl) by electrochemical impedance spectroscopy (EIS) and linear polarization (LP). The results demonstrated a remarkable enhancement of the recycled chips’ properties subjected to hot extrusion followed by the ECAP process. Furthermore, the successive ECAP passes leads to increased film thickness and decreased corrosion rate.

Corrosion resistance of composite coating used for fastener protection

2019 ◽  
Vol 66 (5) ◽  
pp. 595-602
Author(s):  
Zhifeng Lin ◽  
Likun Xu ◽  
Xiangbo Li ◽  
Li Wang ◽  
Weimin Guo ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Carbon Steel ◽  
Composite Coating ◽  
Marine Environment ◽  
Electrochemical Impedance ◽  
Salt Spray ◽  
Diffusion Method ◽  
Economic Losses ◽  
Neutral Salt ◽  
Content Type

Purpose The purpose of this paper is to examine the performance of a fastener composite coating system, sherardized (SD) coating/zinc-aluminum (ZA) coating whether it has good performance in marine environment. Design/methodology/approach In this paper, SD coating was fabricated on fastener surface by solid-diffusion method. ZA coating was fabricated by thermal sintering method. Corrosion behaviours of the composite coating were investigated with potentiodynamic polarization curves, open circuit potential and electrochemical impedance spectroscopy methods. Findings Neutral salt spray (NSS) and deep sea exposure tests revealed that the composite coating had excellent corrosion resistance. Polarization curve tests showed that corrosion current density of the sample with composite coating was significantly decreased, indicating an effective corrosion protection of the composite coating. OCP measurement of the sample in NaCl solution demonstrated that the composite coating had the best cathodic protection effect. The good corrosion resistance of the composite coating was obtained by the synergy of SD and ZA coating. Practical implications SD/ZA coating can be used in marine environment to prolong the life of carbon steel fastener. Social implications SD/ZA composite coating can reduce the risk and accident caused by failed fastener, avoid huge economic losses. Originality/value A new kind of composite coating was explored to protect the carbon steel fastener in marine environment. And the composite coating has the long-term anti-corrosion performance both in simulated and marine environment test.

Sign in / Sign up

Export Citation Format

Share Document