scholarly journals Прозрачные фотокаталитические ZnO-SnO-=SUB=-2-=/SUB=- нанопокрытия, полученные полимерно-солевым методом

2019 ◽  
Vol 126 (4) ◽  
pp. 515
Author(s):  
С.К. Евстропьев ◽  
Л.Л. Лесных ◽  
Н.В. Никоноров ◽  
А.В. Караваева ◽  
Е.В. Колобкова ◽  
...  
Keyword(s):  
Substrate Surface ◽  
Chemical Processes ◽  
Structure And Properties ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Thin Oxide Films ◽  
Glass Surfaces ◽  
Physical And Chemical ◽  
Scanning Electron

AbstractThe structure and properties of transparent ZnO–SnO_2 photocatalytic coatings formed on glass surfaces by the polymer–salt method are studied. The physical and chemical processes occurring during formation of the coatings are studied by differential scanning calorimetry and X-ray diffraction analysis. The structure and optical properties of the obtained thin oxide films are studied by optical spectroscopy, photoluminescence, and scanning electron microscopy. It is shown that the polymer–salt method allows formation of homogeneous and transparent ZnO–SnO_2 coatings consisting of oxide nanoparticles completely covering the glass substrate surface. It is found that the formed transparent ZnO–SnO_2 coatings have high photocatalytic properties and can generate singlet oxygen under action of UV radiation.

The Effect of Molecular Weight on the Structure and Properties of PAN Precursor

2013 ◽  
Vol 781-784 ◽  
pp. 2609-2613 ◽  
Author(s):  
Xue Lin ◽  
Cheng Guo Wang ◽  
Mei Jie Yu ◽  
Zhi Tao Lin
Keyword(s):  
Molecular Weight ◽  
Surface Defects ◽  
Exothermic Reaction ◽  
Interlayer Spacing ◽  
Structure And Properties ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Scanning Electron ◽  
Effect Of Surface

The effect of molecular weight on the structure and properties of PAN precursor was studied by the combination of scanning electron microscopy (SEM), X-ray diffraction (XRD) and differential scanning calorimetry (DSC), etc. With the molecular weight increasing, the grooves on the surface become deeper and rougher, the interlayer spacing and crystallite size increase, and the exothermic reaction occurred later. The strength and breaking extension of PAN precursors increase gradually with the molecular weight increasing. The effect of molecular weight is greater than the effect of surface defects on strength for PAN precursor of high molecular weight.

scholarly journals Extraction of Boron from Ludwigite Ore: Mechanism of Soda-Ash Roasting of Lizardite and Szaibelyite

Minerals ◽  
2019 ◽  
Vol 9 (9) ◽  
pp. 533 ◽  
Author(s):  
Xin Zhang ◽  
Guanghui Li ◽  
Jinxiang You ◽  
Jian Wang ◽  
Jun Luo ◽  
...  
Keyword(s):  
Sodium Carbonate ◽  
Energy Dispersive Spectrometer ◽  
Low Grade ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Selective Activation ◽  
X Ray ◽  
Shed Light ◽  
Soda Ash ◽  
Scanning Electron

Ludwigite ore is a typical low-grade boron ore accounting for 58.5% boron resource of China, which is mainly composed of magnetite, lizardite and szaibelyite. During soda-ash roasting of ludwigite ore, the presence of lizardite hinders the selective activation of boron. In this work, lizardite and szaibelyite were prepared and their soda-ash roasting behaviors were investigated using thermogravimetric-differential scanning calorimetry (TG-DSC), X-ray diffraction (XRD), and scanning electron microscope and energy dispersive spectrometer (SEM-EDS) analyses, in order to shed light on the soda-ash activation of boron within ludwigite ore. Thermodynamics of Na2CO3-MgSiO3-Mg2SiO4-Mg2B2O5 via FactSage show that the formation of Na2MgSiO4 was preferential for the reaction between Na2CO3 and MgSiO3/Mg2SiO4. While, regarding the reaction between Na2CO3 and Mg2B2O5, the formation of NaBO2 was foremost. Raising temperature was beneficial for the soda-ash roasting of lizardite and szaibelyite. At a temperature lower than the melting of sodium carbonate (851 °C), the soda-ash roasting of szaibelyite was faster than that of lizardite. Moreover, the melting of sodium carbonate accelerated the reaction between lizardite with sodium carbonate.

Research on compatibility and surface of high impact bio-based polyamide

2021 ◽  
pp. 095400832110055
Author(s):  
Yang Wang ◽  
Yuhui Zhang ◽  
Yuhan Xu ◽  
Xiucai Liu ◽  
Weihong Guo
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Scanning Electron Microscopy ◽  
Differential Scanning Calorimetry ◽  
Crystallization Behavior ◽  
High Impact ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Scanning Electron

The super-tough bio-based nylon was prepared by melt extrusion. In order to improve the compatibility between bio-based nylon and elastomer, the elastomer POE was grafted with maleic anhydride. Scanning Electron Microscopy (SEM) and Thermogravimetric Analysis (TGA) were used to study the compatibility and micro-distribution between super-tough bio-based nylon and toughened elastomers. The results of mechanical strength experiments show that the 20% content of POE-g-MAH has the best toughening effect. After toughening, the toughness of the super-tough nylon was significantly improved. The notched impact strength was 88 kJ/m2 increasing by 1700%, which was in line with the industrial super-tough nylon. X-ray Diffraction (XRD) and Differential Scanning Calorimetry (DSC) were used to study the crystallization behavior of bio-based PA56, and the effect of bio-based PA56 with high crystallinity on mechanical properties was analyzed from the microstructure.

scholarly journals Development of an Oxcarbazepine Solid Dispersion Using Skimmed Milk to Improve the Solubility and Dissolution Profile

2019 ◽  
Vol 11 (05) ◽  
Author(s):  
M. Shah ◽  
D. Patel
Keyword(s):  
Electron Microscopy ◽  
Solid Dispersion ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Infra Red ◽  
Crystalline Nature ◽  
Skimmed Milk ◽  
Scanning Electron

Oxcarbazepine has low solubility and low oral bioavailability, so it’s a challenge to formulate suitable dosage form. In this present investigation, to improve the dissolution rate and solubility, skimmed milk is used as a carrier. Physical mixers were prepared using various drugs to carrier ratio and spray drying technology was used to develop solid dispersion with the carrier. Various techniques were used to characterize the solid dispersion immediately after they were made which includes differential scanning calorimetry, scanning electron microscopy, fourier transform infra- red spectroscopy, X-ray diffraction and in-vitro dissolution profiles. The differential scanning calorimetry thermograms of raw drug indicated of its anhydrous crystalline nature. In thermograms of solid dispersion, the characteristic peak was absent suggesting the change from crystalline nature to amorphous form. X-ray diffraction confirmed those results. X-ray diffraction results of raw drug showed highly intense peak characteristic of its crystalline nature where solid dispersion showed less intense, more diffused peak indicating the change in crystalline form. Fourier transforms infra-red spectroscopy studies showed there was no interaction between drug and carrier. Scanning electron microscopy support the amorphous nature of mixer. The whole formulation showed distinct enhancement in the drug release behavior and solubility. The optimum oxcarbazepine to skimmed milk ratio 1:3 enhances the in-vitro drug release by 3.5 fold and also show distinct increase in solubility. It was concluded that for improvement of solubility of poorly water soluble oxcarbazepine, skimmed milk powder as a carrier can be utilize very well.

Structure and properties of poly(3-hydroxybutyrate-co-3-hydroxyhexanoate)/poly(L-lactic acid) quasi core/sheath melt-electrospun microfibers

2018 ◽  
Vol 89 (9) ◽  
pp. 1770-1781 ◽  
Author(s):  
Huaizhong Xu ◽  
Benedict Bauer ◽  
Masaki Yamamoto ◽  
Hideki Yamane
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Lactic Acid ◽  
Tensile Tests ◽  
Processing Parameters ◽  
Structure And Properties ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Diffraction Patterns

A facile route was proposed to fabricate core–sheath microfibers, and the relationships among processing parameters, crystalline structures and the mechanical properties were investigated. The compression molded poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) (PHBH)/poly(L-lactic acid) (PLLA) strip enhanced the spinnability of PHBH and the mechanical properties of PLLA as well. The core–sheath ratio of the fibers was determined by the prefab strip, while the PLLA sheath component did not completely cover the PHBH core component due to the weak interfacial tension between the melts of PHBH and PLLA. A rotational target was applied to collect aligned fibers, which were further drawn in a water bath. The tensile strength and the modulus of as-spun and drawn fibers increased with increasing the take-up velocities. When the take-up velocity was above 500 m/min, the jet became unstable and started to break up at the tip of the Taylor cone, decreasing the mechanical properties of the fibers. The drawing process facilitated the crystallization of PLLA and PHBH, and the tensile strength and the modulus increased linearly with the increasing the draw ratio. The crystal information displayed from wide-angle X-ray diffraction patterns and differential scanning calorimetry heating curves supported the results of the tensile tests.

scholarly journals Preparation and Properties of Ginger Essential Oil β-Cyclodextrin/Chitosan Inclusion Complexes

Coatings ◽  
2018 ◽  
Vol 8 (9) ◽  
pp. 305 ◽  
Author(s):  
Yan Zhang ◽  
Hui Zhang ◽  
Fang Wang ◽  
Li-Xia Wang
Keyword(s):  
Particle Size ◽  
Essential Oil ◽  
Spray Drying ◽  
Small Particle Size ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Ft Ir ◽  
Thermal Stability Of ◽  
Scanning Electron

The ginger essential oil/β-cyclodextrin (GEO/β-CD) composite, ginger essential oil/β-cyclodextrin/chitosan (GEO/β-CD/CTS) particles and ginger essential oil/β-cyclodextrin/chitosan (GEO/β-CD/CTS) microsphere were prepared with the methods of inclusion, ionic gelation and spray drying. Their properties were studied by using scanning electron microscopy (SEM), differential scanning calorimetry (DSC), thermo-gravimetry analysis (TGA), Fourier transform infrared spectroscopy (FT-IR) and X-ray diffraction (XRD). The results showed that the particle size of GEO/β-CD composite was smaller than that of β-CD and GEO/β-CD/CTS particles were loose and porous, while the microsphere obtained by spray drying had certain cohesiveness and small particle size. Besides, results also indicated that β-CD/CTS could modify properties and improve the thermal stability of GEO, which would improve its application value in food and medical industries.

The Degradation of Poly (Butylene Succinate)/Natural Rubber Composites

2014 ◽  
Vol 934 ◽  
pp. 110-115
Author(s):  
Li Gao ◽  
Er Juan Zhi ◽  
Ping Li Wang ◽  
Jun Hui Ji
Keyword(s):  
Green Composites ◽  
X Ray Diffraction ◽  
Rubber Composites ◽  
Scanning Calorimetry ◽  
Butylene Succinate ◽  
X Ray ◽  
Weight Losses ◽  
Natural Rubber Composites ◽  
Degradation Test ◽  
Scanning Electron

In this study, poly (butylene succinate) (PBS)/nature rubber (NR) composites were prepared, and the effects of NR content on the biodegradability were evaluated by vermiculite-degradation test. X-ray Diffraction, differential scanning calorimetry (DSC), and scanning electron microscopy (SEM) were used to characterize the degraded blends. The weight losses of PBS/NR composites are higher than that of pure PBS, and increased with adding NR content. The weight loss of 30% NR content composite after 120 days is 16.84%. The XRD and DSC results show that the crystallinity of PBS/NR composites increase after buried in vermiculite. These results were confirmed using SEM observations by the presence of many large holes and more cracks in the degradation surface morphology of the increasing content of NR. It was observed that PBS/NR composites are green-composites or eco-materials.

scholarly journals Deformation induced martensite characterization in Fe-30%Ni-5%Cu alloy

2012 ◽  
Vol 48 (2) ◽  
pp. 259-264 ◽  
Author(s):  
E. Güler ◽  
M. Güler
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Dsc Measurements ◽  
Cu Alloy ◽  
The Face ◽  
Xrd Techniques ◽  
Scanning Electron

Deformation induced martensite properties were examined according to existing martensite morphology, crystallography and formation temperatures for different prior austenite homogenization conditions in Fe-30%Ni-5%Cu alloy. Scanning electron microscope (SEM), differential scanning calorimetry (DSC) and X-ray diffraction (XRD) techniques were employed to investigation. Scanning electron microscope observations showed elongated deformation induced martensite morphology in the austenite phase of alloy. As well, after deformation martensite start temperatures (Ms) were determined as -101?C and -105?C from DSC measurements for different homogenization conditions. In addition, X-ray diffraction analysis revealed the face centred cubic (fcc) of austenite phases and body centred cubic (bcc) deformation induced martensite phases for all studied samples.

Study of an Energetic-oxidant Co-crystal: Preparation, Characterisation, and Crystallisation Mechanism

2017 ◽  
Vol 67 (5) ◽  
pp. 510 ◽  
Author(s):  
Han Gao ◽  
Wei Jiang ◽  
Jie Liu ◽  
Gazi Hao ◽  
Lei Xiao ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Differential Scanning Calorimetry ◽  
Diffraction Spectrum ◽  
Solvent Evaporation Method ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Scanning Electron

<p>An energetic co-crystal consisting of the most promising military explosive 2,4,6,8,10,12-hexanitro-2,4,6,8,10,12-hexaazaisowurtzitane (CL-20) and the most well-known oxidant applied in propellants ammonium perchlorate has been prepared with a simple solvent evaporation method. Scanning electron microscopy revealed that the morphology of co-crystal differs greatly from each component. The X-ray diffraction spectrum, FTIR, Raman spectra, and differential scanning calorimetry characterisation further prove the formation of the co-crystal. The result of determination of hygroscopic rate indicated the hygroscopicity was effectively reduced. At last, the crystallisation mechanism has been discussed.</p>

Synthesis, Characterization and Magnetism of Nanosized Copper Ferrite

2008 ◽  
Vol 368-372 ◽  
pp. 604-606 ◽  
Author(s):  
Wei Zhong Lv ◽  
Zhong Kuang Luo ◽  
Bo Liu ◽  
Xiang Zhong Ren ◽  
Hong Hua Cai ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Thermal Analysis ◽  
Copper Ferrite ◽  
Sonochemical Method ◽  
Thermal Gravimetric ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Ft Ir ◽  
Scanning Electron

Copper ferrite powders were successfully synthesized by sonochemical method. The resultant powders were investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), FT-IR, differential thermal analysis-thermal gravimetric (DTA-TG), differential scanning calorimetry (DSC) and VSM. The particle saturation magnetization (Ms) is 66 emu/g and an intrinsic coercive force (iHc) is 2100 Oe when the precursor calcined at 950 °C for 15 h.

Sign in / Sign up

Export Citation Format

Share Document