Effects of Steam Injection Flow in Burner and Outside Water Tube to the Increasing of Boiler Temperature

2007 ◽  
Vol 7 (1 & 2) ◽  
pp. 120
Author(s):  
M. Djoni Bustan
Keyword(s):  
Human Life ◽  
Combustion Process ◽  
Production Capacity ◽  
Steam Injection ◽  
Oil Refinery ◽  
Specific Enthalpy ◽  
Maximum Pressure ◽  
Injection Flow ◽  
Electrical Generator ◽  
Generator Unit

Energy is an expensive basic need for human life, especially energy from fossils, such as crude oil, gas, and coal. In an oil refinery factory or electrical generator unit, where heat is most dominantly utilized, the boiler is used to generate steam. The main problem in a boiler is its uncompleted combustion process because of the incomplete ratio of air–fuel. This problem is caused by the addition of deposits or sealing inside and outside of the tube fire heater which will reduce the performance of fired heater. The objective of this research is to study the effect of steam flow variation on burner and tubing for increasing heat and temperature as well as the quality of steam. This research used a package boiler B&W series 1986 model which can be seen at an oil refinery factory or steam power electrical generator unit in Indonesia. This package boiler has 50kg/hours steam production capacity, qualified superheated steam, maximum pressure and temperature at 7kgs/cms2 and 700oC. Quantitatively, the achievable heat efficiency which corresponded to the temperature increase caused by the steam injection is 41.25% and the specific enthalpy is 12.07%.

Vibration analysis and combustion parameter evaluation of CI engine based on Fourier Decomposition Method

2021 ◽  
pp. 146808742098819
Author(s):  
Wang Yang ◽  
Cheng Yong
Keyword(s):  
Vibration Analysis ◽  
Decomposition Method ◽  
Combustion Process ◽  
Pressure Rise ◽  
Maximum Pressure ◽  
Vibration Signals ◽  
Loop Control ◽  
Fourier Decomposition ◽  
Surface Vibration ◽  
Rise Rate

As a non-intrusive method for engine working condition detection, the engine surface vibration contains rich information about the combustion process and has great potential for the closed-loop control of engines. However, the measured engine surface vibration signals are usually induced by combustion as well as non-combustion excitations and are difficult to be utilized directly. To evaluate some combustion parameters from engine surface vibration, the tests were carried out on a single-cylinder diesel engine and a new method called Fourier Decomposition Method (FDM) was used to extract combustion induced vibration. Simulated and test results verified the ability of the FDM for engine vibration analysis. Based on the extracted vibration signals, the methods for identifying start of combustion, location of maximum pressure rise rate, and location of peak pressure were proposed. The cycle-by-cycle analysis of the results show that the parameters identified based on vibration and in-cylinder pressure have the similar trends, and it suggests that the proposed FDM-based methods can be used for extracting combustion induced vibrations and identifying the combustion parameters.

Effects of Natural Gas Compositions on Engine In-Cylinder Process

2015 ◽  
Vol 1092-1093 ◽  
pp. 498-503
Author(s):  
La Xiang ◽  
Yu Ding
Keyword(s):  
Natural Gas ◽  
Alternative Fuels ◽  
Combustion Process ◽  
Engine Performance ◽  
Maximum Temperature ◽  
Maximum Pressure ◽  
Test Bed ◽  
Promising Alternative ◽  
Natural Gas Engines ◽  
Lower Maximum

Natural gas (NG) is one of the most promising alternative fuels of diesel and petrol because of its economics and environmental protection. Generally the NG engine share the similar structure profile with diesel or petrol engine but the combustion characteristics of NG is varied from the fuels, so the investigation of NG engine combustion process receive more attentions from the researchers. In this paper, a zero-dimensional model on the basis of Vibe function is built in the MATLAB/SIMULINK environment. The model provides the prediction of combustion process in natural gas engines, which has been verified by the experimental data in the NG test bed. Furthermore, the influence of NG composition on engine performance is investigated, in which the in-cylinder maximum pressure and temperature and mean indicated pressure are compared using different type NG. It is shown in the results that NG with higher composition of methane results in lower maximum temperature and mean indicated pressure as well as higher maximum pressure.

scholarly journals Some aspects of cycle variability at the Diesel engine fuelled with animal fats

2019 ◽  
Vol 112 ◽  
pp. 01014
Author(s):  
Adrian Nicolici ◽  
Constantin Pană ◽  
Niculae Negurescu ◽  
Alexandru Cernat ◽  
Cristian Nuţu
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Alternative Fuels ◽  
Combustion Process ◽  
Pollutant Emissions ◽  
Experimental Investigations ◽  
Maximum Pressure ◽  
Content Increase ◽  
Animal Fats ◽  
Viable Solution

The progressive diminution of the oil reserves all over the world highlights the necessity of using alternative fuels derived from durable renewable resource. The use of the alternative fuels represents a viable solution to reduce the pollutant emissions and to replace fossil fuels. Thus, a viable solution is the use of the animal fats in mixture with the diesel fuel at the diesel engines. A D2156 MTN8 diesel engine was firstly fuelled with diesel fuel and then with different blends of diesel fuel-animal fats (5% and 10% animal fats content). In the paper are presented some results of the experimental investigations of engine fuelled with preheated animal fats. The raw animal fats effects on the combustion process and on the pollutant emissions at different engine loads and 1450 rev/min engine speed are showed. The engine cycle variability increases at the animal fats content increase. The cycle variability for maximum pressure, maximum pressure angle and indicated mean effective pressure is analysed. The cycle variability coefficients values don’t exceed the recommended values of the standard diesel engine.

scholarly journals An Experimental Study on the Performance and Emission of the diesel/CNG Dual-Fuel Combustion Mode in a Stationary CI Engine

Energies ◽  
2019 ◽  
Vol 12 (20) ◽  
pp. 3857 ◽  
Author(s):  
Arkadiusz Jamrozik ◽  
Wojciech Tutak ◽  
Karol Grab-Rogaliński
Keyword(s):  
Diesel Fuel ◽  
Carbon Dioxide Emissions ◽  
Combustion Engine ◽  
Combustion Process ◽  
Pressure Rise ◽  
Dual Fuel ◽  
Maximum Pressure ◽  
Stable Operation ◽  
Performance And Emission ◽  
Ci Engine

One of the possibilities to reduce diesel fuel consumption and at the same time reduce the emission of diesel engines, is the use of alternative gaseous fuels, so far most commonly used to power spark ignition engines. The presented work concerns experimental research of a dual-fuel compression-ignition (CI) engine in which diesel fuel was co-combusted with CNG (compressed natural gas). The energy share of CNG gas was varied from 0% to 95%. The study showed that increasing the share of CNG co-combusted with diesel in the CI engine increases the ignition delay of the combustible mixture and shortens the overall duration of combustion. For CNG gas shares from 0% to 45%, due to the intensification of the combustion process, it causes an increase in the maximum pressure in the cylinder, an increase in the rate of heat release and an increase in pressure rise rate. The most stable operation, similar to a conventional engine, was characterized by a diesel co-combustion engine with 30% and 45% shares of CNG gas. Increasing the CNG share from 0% to 90% increases the nitric oxide emissions of a dual-fuel engine. Compared to diesel fuel supply, co-combustion of this fuel with 30% and 45% CNG energy shares contributes to the reduction of hydrocarbon (HC) emissions, which increases after exceeding these values. Increasing the share of CNG gas co-combusted with diesel fuel, compared to the combustion of diesel fuel, reduces carbon dioxide emissions, and almost completely reduces carbon monoxide in the exhaust gas of a dual-fuel engine.

scholarly journals Comparative Analysis of Combustion Stability of Diesel/Ethanol Utilization by Blend and Dual Fuel

Processes ◽  
2019 ◽  
Vol 7 (12) ◽  
pp. 946 ◽  
Author(s):  
Wojciech Tutak ◽  
Arkadiusz Jamrozik
Keyword(s):  
Diesel Fuel ◽  
Fuel Injection ◽  
Combustion Process ◽  
Combustion Stability ◽  
Dual Fuel ◽  
Maximum Pressure ◽  
Compression Ignition Engine ◽  
Energy Fraction ◽  
Pure Ethanol ◽  
Advantages And Disadvantages

The aim of the work is a comparison of two combustion systems of fuels with different reactivity. The first is combustion of the fuel mixture and the second is combustion in a dual-fuel engine. Diesel fuel was burned with pure ethanol. Both methods of co-firing fuels have both advantages and disadvantages. Attention was paid to the combustion stability aspect determined by COVIMEP as well as the probability density function of IMEP. It was analyzed also the spread of the maximum pressure value, the angle of the position of maximum pressure. The influence of ethanol on ignition delay time spread and end of combustion process was evaluated. The experimental investigation was conducted on 1-cylinder air cooled compression ignition engine. The test engine operated with constant rpm equal to 1500 rpm and constant angle of start of diesel fuel injection. The engine was operated with ethanol up to 50% of its energy fraction.

The scavenging timing of pre-chamber on the performance of a natural gas engine

2020 ◽  
pp. 146808742096087
Author(s):  
Xue Yang ◽  
Yong Cheng ◽  
Pengcheng Wang
Keyword(s):  
Natural Gas ◽  
Combustion Process ◽  
Injection System ◽  
Maximum Pressure ◽  
Ignition Process ◽  
Main Chamber ◽  
Ignition Timing ◽  
Gas Engine ◽  
Natural Gas Engines ◽  
Natural Gas Engine

The pre-chamber ignition system scavenged with natural gas can effectively improve the in-cylinder combustion process and extend the lean-burn limit of natural gas engines. The scavenging process affects the flow field and fuel-air mixture concentration distribution in the pre-chamber and affects the combustion process in the pre-chamber as well as the ignition process in the main chamber. This has a significant influence on the performance of natural gas engines. It is supposed that the ratio of natural gas remaining in the mixture inside the pre-chamber at the ignition timing affects the combustion process in the pre-chamber. To verify this suppose, an independent injection system for injecting natural gas into the pre-chamber is designed and experiments are carried out on a single-cylinder natural gas engine. The ratio of natural gas remaining in the mixture inside the pre-chamber at the ignition timing is adjusted by changing the injection start angle of the scavenging process. The combustion process in the pre-chamber and the main chamber are analyzed using the in-cylinder pressures. The results indicate that, with the delay of the injection start angle, the ratio of natural gas remaining in the mixture inside the pre-chamber at the ignition timing increases, the combustion process in the pre-chamber is enhanced, the maximum pressure difference between two chambers increases and appears earlier. The energy of the hot jets and the penetration of the jets increase, which enhances the combustion process in the main chamber.

scholarly journals Energy Willow From Experimental Plantation as a Potentially Clean Energy Source

2017 ◽  
Vol 24 (2) ◽  
pp. 203-212 ◽  
Author(s):  
Monika Janas ◽  
Alicja Zawadzka
Keyword(s):  
Heavy Metals ◽  
Combustion Process ◽  
Production Capacity ◽  
Calorific Value ◽  
Absorption Spectrometry ◽  
Clean Energy ◽  
Heat Of Combustion ◽  
Wide Range ◽  
Close Relationship ◽  
Clean Energy Source

Abstract Energy willow as a species with broad adaptation possibilities, large production capacity and a wide range of applications, takes a special place among the plants grown for energy production. In this work an analysis was conducted in respect of the usefulness of this type of wood from experimental plantations as a clean source of energy generated in the combustion process. The heat of combustion and net calorific value of dry matter of energy willow wood, including selected sorts and classes of thickness were determined. Energy willow has a natural ability to accumulate heavy metals which are oxidized during the combustion process or remain in the ash, and consequently repollute the environment. In order to determine the environmental impact the content of heavy metals was examined in energy willow wood and in the soil of the experimental plantation. Metal concentrations were determined by the Atomic Absorption Spectrometry method (AAS). Results of the tests confirmed a close relationship between the heat of combustion, calorific value and wood thickness as well as its location in the tree structure. Furthermore, very large differences were found in the content of heavy metals in the samples of both willow wood and soil. The levels of heavy metal content in the wood of energy willow determine the agricultural use of ashes produced during combustion.

Numerical Simulation of Seismic Risk and Loss Propagation Effects in Process Plants: An Oil Refinery Case Study

2017 ◽  
Author(s):  
Antonio C. Caputo ◽  
Alessandro Vigna
Keyword(s):  
Risk Assessment ◽  
Seismic Risk ◽  
Production Capacity ◽  
Industrial Process ◽  
Oil Refinery ◽  
Quantitative Methodology ◽  
Seismic Risk Assessment ◽  
Technical Standards ◽  
Process Plants

Process plants are vulnerable to natural hazards and, in particular, to earthquakes. Nevertheless, the quantitative assessment of seismic risk of process plants is a complex task because available methodologies developed in the field of civil and nuclear engineering are not readily applicable to process plants, while technical standards and regulations do not establish any procedure for the overall seismic risk assessment of industrial process plants located in earthquake-prone areas. This paper details the results of a case study performing a seismic risk assessment of an Italian refinery having a 85,000 barrels per day production capacity, and a storage capacity of over 1,500,000 m3. The analysis has been carried out resorting to a novel quantitative methodology developed in the framework of a European Union research program (INDUSE 2 SAFETY). The method is able to systematically generate potential starting scenarios, deriving from simultaneous interactions of the earthquake with each separate equipment, and to account for propagation of effects between distinct equipment (i.e. Domino effects) keeping track of multiple simultaneous and possibly interacting chains of accidents. In the paper the methodology, already described elsewhere, is briefly resumed, and numerical results are presented showing relevant accident chains and expected economic loss, demonstrating the capabilities of the developed tool.

scholarly journals DESIGN OF SIMPLE ELECTRICAL GENERATOR AS HIGH SCHOOL LEARNING MEDIA

2020 ◽  
Vol 4 (1) ◽  
pp. 44-49
Author(s):  
Syarifah Muthia Putri ◽  
Zulkifli Bahri ◽  
Dina Maizana
Keyword(s):  
Electric Power ◽  
Power Plants ◽  
Human Life ◽  
Electrical Energy ◽  
Electric Power Plants ◽  
Upper Secondary ◽  
School Learning ◽  
Electrical Generator ◽  
Training Activities ◽  
Upper Secondary Level

Electrical energy has an important role in human life today. Many aspects of human life today rely on electrical energy. National electrical energy defense is an important issue so that Indonesia can become an independent nation in the field of electrical energy sources. Strategies in realizing this issue can be implemented by fostering the interests and talents of upper secondary level students so that the students will explore the field of electricity science. Training on simple electricity generation was conducted for students of Budi Utomo Binjai Private Vocational School so that the students could improve their skills and insight on electricity. The training was carried out by providing an understanding of the role and condition of current electricity, the design of a simple electric power plant, and providing insights on renewable energy. The results of the design during the training are given to the school which can be used as a medium of learning for students in the future. Based on the results of the questionnaire given to students during training it can be seen that 61% of the total number of students participating in training activities can have sufficiently good skills in designing simple electric power plants.

Sign in / Sign up

Export Citation Format

Share Document