scholarly journals Effect of Denitrifying Bacterial Biomass and Carbon Sources on Nitrate Removal

2020 ◽  
Vol 14 (4) ◽  
pp. 2417-2424
Author(s):  
Essam J. Alyamani ◽  
Rayan Y. Booq ◽  
Ali H. Bahkali ◽  
Sulaiman A. Alharbi
Keyword(s):  
Pseudomonas Aeruginosa ◽  
Carbon Source ◽  
Conventional Treatment ◽  
Nitrate Removal ◽  
Carbon Sources ◽  
Bacterial Biomass ◽  
Alkaline Ph ◽  
Biological Denitrification ◽  
Bacterial Inoculum ◽  
Denitrification Process

Denitrification based on immobilized microbial cellulose may offer an economical replacement for conventional treatment for nitrate removal. The environmental and bacterial biomass may influence the rate of biological denitrification processes. This study aimed to investigate the factors that affect denitrification rates, including carbon sources, pH, and bacterial inoculum. Different inoculum biomass of Pseudomonas aeruginosa and various carbon sources of glucose, sucrose, and cellulose with different concentrations were tested to assimilate 100 mg/L of KNO3 as nitrate source. Additionally, five additional inoculations, five different incubation time, and seven different pH levels were studied. The Pseudomonas aeruginosa isolates used different mineral media with three carbon sources, glucose, sucrose, and cellulose, with different concentrations at different rates to denitrify nitrate. The highest denitrification rate was with glucose after 18 hrs and was after 24 hrs when sucrose and cellulose were used, respectively. The bacterial biomass denitrification level was the highest, between 0.8% and 1% of OD600=1. Nitrate removal by Pseudomonas aeruginosa was the highest at pH 7, 8, and 9. This report suggests that when glucose is used as a carbon source, at neutral to alkaline pH, and 1% of denitrifying bacterial biomass, the highest level of biological denitrification process may be achieved.

Nitrate removal using Brevundimonas diminuta MTCC 8486 from ground water

2009 ◽  
Vol 60 (2) ◽  
pp. 517-524 ◽  
Author(s):  
S. Kavitha ◽  
R. Selvakumar ◽  
M. Sathishkumar ◽  
K. Swaminathan ◽  
P. Lakshmanaperumalsamy ◽  
...  
Keyword(s):  
Carbon Source ◽  
Ground Water ◽  
Nitrate Removal ◽  
Carbon Sources ◽  
Treatment Plant ◽  
Growth Conditions ◽  
Pilot Scale ◽  
Biological Removal ◽  
Treatment Processes ◽  
Brevundimonas Diminuta

Brevundimonas diminuta MTCC 8486, isolated from marine soil of coastal area of Trivandrum, Kerala, was used for biological removal of nitrate from ground water collected from Kar village of Pali district, Rajasthan. The organism was found to be resistance for nitrate up to 10,000 mg L−1. The optimum growth conditions for biological removal of nitrate were established in batch culture. The effect of carbon sources on nitrate removal was investigated using mineral salt medium (MSM) containing 500 mg L−1 of nitrate to select the most effective carbon source. Among glucose and starch as carbon source, glucose at 1% concentration increased the growth (182±8.24 × 104 CFU mL−1) and induced maximum nitrate reduction (86.4%) at 72 h. The ground water collected from Kar village, Pali district of Rajasthan containing 460±5.92 mg L−1 of nitrate was subjected to three different treatment processes in pilot scale (T1 to T3). Higher removal of nitrate was observed in T2 process (88%) supplemented with 1% glucose. The system was scaled up to 10 L pilot scale treatment plant. At 72 h the nitrate removal was observed to be 95% in pilot scale plant. The residual nitrate level (23±0.41 mg L−1) in pilot scale treatment process was found to be below the permissible limit of WHO.

Comparison of denitrification performances using PLA/starch with different mass ratios as carbon source

2015 ◽  
Vol 71 (7) ◽  
pp. 1019-1025 ◽  
Author(s):  
Chuanfu Wu ◽  
Danqi Tang ◽  
Qunhui Wang ◽  
Juan Wang ◽  
Jianguo Liu ◽  
...  
Keyword(s):  
Carbon Source ◽  
Groundwater Remediation ◽  
Nitrate Concentration ◽  
Starch Content ◽  
Nitrate Removal ◽  
Carbon Sources ◽  
National Standard ◽  
Biofilm Carrier ◽  
Carbon Release ◽  
Biological Nitrate Removal

A suitable carbon source is significant for biological nitrate removal from groundwater. In this study, slow-release carbon sources containing polylactic acid (PLA) and starch at 8:2, 7:3, 6:4, 5:5, 4:6, and 3:7 ratios were prepared using a blending and fusing technique. The PLA/starch blend was then used as a solid carbon source for biological nitrate removal. The carbon release rate of PLA/starch was found to increase with increased starch content in leaching experiments. PLA/starch at 5:5 mass ratio was found to have the highest denitrification performance and organic carbon consumption efficiency in semi-continuous denitrification experiments, and was also revealed to support complete denitrification at 50 mg-N/L influent nitrate concentration in continuous experiments. The effluent nitrate concentration was <2 mg NO3–-N/L, which met the national standard (GB 14848-93) for groundwater. Scanning electron microscopy results further showed that the surface roughness of PLA/starch increased with prolonged experimental time, which may be conducive to microorganism attachment. Therefore, PLA/starch was a suitable carbon source and biofilm carrier for groundwater remediation.

scholarly journals Impact of Temperature on Biological Denitrification Process

1970 ◽  
Vol 7 (1) ◽  
pp. 121-126 ◽  
Author(s):  
Iswar Man Amatya ◽  
Bhagwan Ratna Kansakar ◽  
Vinod Tare ◽  
Liv Fiksdal
Keyword(s):  
Filtration Rate ◽  
Nitrate Nitrogen ◽  
Nitrate Removal ◽  
Biological Method ◽  
Biological Denitrification ◽  
Nitrite Nitrogen ◽  
Nitrogen Concentrations ◽  
In Series ◽  
Nitrate And Nitrite ◽  
Denitrification Process

Nitrate removal in groundwater was carried out by biological method of denitrification process. The denitrification and without denitrification were performed in two different sets of reactors. Each reactor consists of two columns connected in series packed with over burnt bricks as media. The filtration rate varied from 5.3 to 52.6 m/day for denitrification process. The ammonia, nitrate and nitrite nitrogen concentrations were measured at inlet, intermediate ports and outlet. The temperature varied from 10 to 30°C at 2°C intervals. The results demonstrated that high amount of nitrate nitrogen removed in groundwater at denitrification process. The nitrate nitrogen removed by denitrification varied from 3.50 to 39.08 gm/m3/h at influent concentration from 6.32 to 111.04 gm/m3/h. Denitrification was found more significant above 16°C.Key words: Over burnt brick, Denitrification, Filtration rate and TemperatureJournal of the Institute of Engineering, Vol. 7, No. 1, July, 2009 pp. 121-126doi: 10.3126/jie.v7i1.2070 

Denitrification with isopropanol as a carbon source in a biofilm system

1994 ◽  
Vol 30 (11) ◽  
pp. 69-78 ◽  
Author(s):  
Yongwoo Hwang ◽  
Hiroshi Sakuma ◽  
Toshihiro Tanaka
Keyword(s):  
Carbon Source ◽  
Nitrate Removal ◽  
Growth Yield ◽  
Pilot Scale ◽  
Denitrification Rate ◽  
Hydrogen Donor ◽  
Microbial Oxidation ◽  
Biological Denitrification ◽  
Batch Tests

Several batch tests and pilot-scale investigations on biological denitrification with isopropanol were performed. Isopropanol was converted to acetone by microbial oxidation during denitrification. Isopropanol itself little contributed to denitrification in practice while the converted acetone played a role of a main hydrogen donor. A larger quantity of nitrite intermediate was formed by using methanol compared to the case of isopropanol. The measured requirement of isopropanol was 2.0 mg mg−1 NO3-N, and was 2/3 of methanol. The oxygen equivalent of isopropanol for nitrate removal was almost the same as that of methanol. The denitrifier net growth yield for isopropanol was greater than for methanol. In order to maximize the denitrification rate, it is essential to convert isopropanol to acetone rapidly by accurate dosing for nitrogen load because the denitrification rate was accelerated by using acetone only. Excessive dose of isopropanol can cause a decrease in the denitrification rate as well as an increase of BOD in the effluent.

Groundwater denitrification with alternative carbon sources

1998 ◽  
Vol 38 (6) ◽  
pp. 237-243 ◽  
Author(s):  
A. Mohseni-Bandpi ◽  
D. J. Elliott
Keyword(s):  
Acetic Acid ◽  
Carbon Source ◽  
Nitrate Nitrogen ◽  
Nitrogen Concentration ◽  
Nitrate Removal ◽  
Carbon Sources ◽  
Pilot Scale ◽  
Rotating Biological Contactor ◽  
Nitrogen Ratio ◽  
Biological Nitrate Removal

A pilot scale rotating biological contactor (RBC) was used to investigate the removal of nitrate-nitrogen from groundwater using three different carbon sources, i.e., methanol, ethanol and acetic acid. Optimum carbon sources to influent nitrate-nitrogen ratio were established by varying the influent concentration of carbon sources. The optimum ratio of methanol, ethanol and acetic acid to nitrate-nitrogen ratios were found to be 2.9, 2.35 and 4.3 respectively. The nitrate-nitrogen removal efficiency averaged 93, 91 and 98 for methanol, ethanol and acetic acid respectively at a loading rate of 76 mg/m2.h. The results of this study show that the acetic acid is the most efficient carbon source for removal of nitrate-nitrogen. Effluent nitrite-nitrogen concentration was minimum for acetic acid as compared with ethanol and methanol. The effluent contained minimum suspended solids and turbidity for methanol as a carbon source. The results of this study indicate that biological nitrate removal using a RBC is a reliable and stable system under all the three carbon sources. The denitrified water in all cases requires some post treatment to oxidise the residual carbon source and remove biomass before distribution.

Full-Scale Application of Nitrogen Removal with Methanol as Carbon Source

1992 ◽  
Vol 26 (5-6) ◽  
pp. 1077-1086 ◽  
Author(s):  
U. Nyberg ◽  
H. Aspegren ◽  
B. Andersson ◽  
J. la C. Jansen ◽  
I.S. Villadsen
Keyword(s):  
Carbon Source ◽  
Nitrogen Removal ◽  
Nitrate Removal ◽  
Sewage Treatment ◽  
Carbon Sources ◽  
Treatment Plant ◽  
Cost Effective ◽  
High Level ◽  
Plant Configuration ◽  
Composite Samples

In Sweden many advanced sewage treatment plants for BOD and phosphorus removal have to be extended with nitrogen removal. Due to existing plant configuration and wastewater composition, denitrification with supply of an external carbon source can be a cost-effective solution in many cases. At the Klagshamn wastewater treatment plant in Malmo investigations for extensive nitrogen removal have been made in a single-sludge system with pre-precipitation and post-denitrification where methanol was added for denitrification. Results from the tests showed that a high level of nitrogen removal can be reached, and that the process was stable and easy to operate. The process application gave less supplementary cost for an extended nitrogen removal than for upgrading the plant with larger basin volumes. In order to examine the purification performance caused by the addition of methanol, the starting period was followed extensively with online nitrate sensors and daily composite samples. The development of the denitrif ication capacity of the sludge with methanol and acetate as carbon sources was followed and microbiological changes were examined microscopically. Complete denitrification was obtained after approximately one month at 10°C. The denitrification capacity of the sludge with methanol reached that of acetate after about the same time. The microscopic examination revealed a growing population of budding and/or appendaged bacteria, presumably Hyphomicrobium spp, reaching a stable maximum at the time when optimal nitrate removal occurred.

Comparative Analysis of Nitrate Removal in Sub-Surface Flow Constructed Wetlands by Different External Carbon Sources

2014 ◽  
Vol 1073-1076 ◽  
pp. 779-783
Author(s):  
Patience Awhavbera ◽  
Lian Fang Zhao
Keyword(s):  
Carbon Source ◽  
Wheat Straw ◽  
Constructed Wetlands ◽  
Nitrate Removal ◽  
Waste Product ◽  
Carbon Sources ◽  
Surface Flow ◽  
Synthetic Wastewater ◽  
External Carbon Source ◽  
N Removal

External carbon sources provide additional nutrients that improve the efficiency of nitrate removal in constructed wetlands. Typha angustifolia L. were planted in four vertical subsurface-flow constructed wetlands. Different external carbon sources were fed into the columns, to investigate and compare their treatment of nitrate in synthetic wastewater, with initial influent C/N ratio of 1:1. Wetland A (WA) with 50g wheat straw as external carbon source, wetland B (WB) with 50g woodchips, wetland C (WC) with additional 10mg/L glucose and wetland D (WD) without external carbon source to serve as the control, were used in the lab-scale experimental study. WA, WB, WC and WD within a period of 24 days, cumulatively removed 109.38mg/L, 93.75mg/L, 85.14mg/L, and 64.01mg/L nitrate, respectively, from the influent. The nitrate-nitrogen (NO3–N) removal efficiency as aided by the external carbon sources was in the order: wheat straw > woodchips > glucose > control. Wheat straw treated 93% NO3–N, woodchips 78%, glucose 72% and the control 53%. The results indicate that WA, WB and WC outperformed the control system, due to the additional carbon sources. In general, the wheat straw had a better performance than wood chips and glucose. Thus, wheat straw as low cost biological waste product is recommended for the treatment of nitrate in wetlands.

Comparison of aerobic denitrifying activity among three cultural species with various carbon sources

2004 ◽  
Vol 50 (8) ◽  
pp. 15-22 ◽  
Author(s):  
Y. Otani ◽  
K. Hasegawa ◽  
K. Hanaki
Keyword(s):  
Carbon Source ◽  
Nitrate Reduction ◽  
Sodium Acetate ◽  
Nitrate Removal ◽  
Carbon Sources ◽  
Alcaligenes Faecalis ◽  
Aerobic Denitrification ◽  
Denitrification Activity ◽  
Paracoccus Pantotrophus ◽  
Nitrate And Nitrite

Abilities of three aerobic denitrifiers such as Alcaligenes faecalis, Microvirgula aerodenitrificans and Paracoccus pantotrophus were compared from the viewpoints of nitrate removal efficiency and organic matter utilization. First, the effect of carbon source was investigated. Although nitrate reduction was observed in all strains under aerobic conditions, a change of carbon source considerably affected the denitrification ability. In the case of P. pantotrophus, nitrate and nitrite were completely removed in three days under sodium acetate or leucine as a carbon source. In the case of A. faecalis, sufficient nitrate removal was observed only when sodium acetate or ethanol was added. P. pantotrophus and A. faecalis showed a higher ability of nitrate removal than that of M. aerodenitrificans. Therefore, P. pantotrophus was selected in order to investigate the effects of concentration and repetitive addition of carbon. Sodium acetate was used as a sole carbon source. Nitrate was not reduced when the carbon concentration was below 500 mgC/L. However, when carbon source was added repeatedly, nitrate was reduced under 100 mgC/L after the optical density of the bacterium reached above 1.0. This result indicated that a high enough level of bacterial density was necessary to express aerobic denitrification activity.

Comparison and Analysis of Denitrification Effect and Kinetics Regarding Several New Type Carbon Sources

2011 ◽  
Vol 255-260 ◽  
pp. 2695-2699
Author(s):  
Hao Yan Li ◽  
Dian Hai Yang ◽  
Hai Yan Wu ◽  
Qin Lu ◽  
Xiang Zheng
Keyword(s):  
Carbon Source ◽  
Nitrate Removal ◽  
Carbon Sources ◽  
Batch Reactors ◽  
Order Kinetic ◽  
Starch Solution ◽  
Primary Sludge ◽  
Carbon Decomposition ◽  
Order Kinetic Model ◽  
Denitrification Kinetics

Three typical external carbon sources (i.e. leachate, hydrolysates from primary sludge and starch solution) with regard to the denitrification process were investigated respectively in sequencing batch reactors (SBR) and their denitrification properties were compared to provide the optimum substrate suited for nitrogen removal processes. The variations of nitrogen were examined and nitrate utility ratio as well as carbon consumption rate was exhibited, denitrification kinetics regarding leachate was also analyzed by use of zero-order kinetic model. The experimental results indicated that the similar denitrification trend was achieved between hydrolysates from primary sludge and starch solution other than leachate as carbon source in denitrification system. The nitrate was not entirely degraded and the nitrite generated permanent accumulation. Compared with other carbon sources, leachate in steady operation showed the highest nitrate removal concentration and rate in phase I with an average of 13 mg/L and 86%, respectively. In phase II, the maximum nitrate and carbon decomposition rates were 0.088 g N/g VSS•d and 0.848 g TOC/g VSS•d respectively occurring at leachate as substrate. Thus, stable leachate was considered as the most suitable carbon source in comparison with other substrates.

scholarly journals Pseudomonas aeruginosa transcriptome adaptations from colonization to biofilm infection of skin wounds

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Peter D’Arpa ◽  
S. L. Rajasekhar Karna ◽  
Tsute Chen ◽  
Kai P. Leung
Keyword(s):  
Pseudomonas Aeruginosa ◽  
Carbon Source ◽  
Wound Infection ◽  
Glyoxylate Cycle ◽  
Acute Infection ◽  
Carbon Sources ◽  
Myeloid Cell ◽  
Carbon Utilization ◽  
Branched Chain ◽  
Biofilm Infection

AbstractIn burn patients Pseudomonas aeruginosa infection is a major cause of morbidity. Analysis of the pathogen’s gene expression as it transitions from colonization to acute and then biofilm wound infection may provide strategies for infection control. Toward this goal, we seeded log-phase P. aeruginosa (PAO1) into 3-day-old, full-thickness excision wounds (rabbit ear) and harvested the bacteria during colonization (Hrs 2 and 6), acute infection (Hr 24), and biofilm infection (Days 5 and 9) for transcriptome analysis (RNA-Seq). After 2–6 h in the wound, genes for metabolism and cell replication were down-regulated while wound-adaptation genes were up-regulated (vs. expression in log-phase culture). As the infection progressed from acute to biofilm infection, more genes became up-regulated than down-regulated, but the down-regulated genes enriched in more pathways, likely because the genes and pathways that bacteria already colonizing wounds up-regulate to establish biofilm infection are less known. Across the stages of infection, carbon-utilization pathways shifted. During acute infection, itaconate produced by myeloid cells appears to have been a carbon source because myeloid cell infiltration and the expression of the host gene, ACOD1, for itaconate production peaked coincidently with the expression of the PAO1 genes for itaconate transport and catabolism. Additionally, branched-chain amino acids are suggested to be a carbon source in acute infection and in biofilm infection. In biofilm infection, fatty acid degradation was also up-regulated. These carbon sources feed into the glyoxylate cycle that was coincidently up-regulated, suggesting it provided the precursors for P. aeruginosa to synthesize macromolecules in establishing wound infection.

Sign in / Sign up

Export Citation Format

Share Document