scholarly journals Oxidation of aniline in the presence of phenolic acids

2010 ◽  
Vol 64 (3) ◽  
pp. 215-220 ◽  
Author(s):  
Aleksandra Janosevic ◽  
Gordana Ciric-Marjanovic
Keyword(s):  
Phenolic Acids ◽  
Ph Value ◽  
Polymerization Degree ◽  
Emeraldine Salt ◽  
Sulfosalicylic Acid ◽  
Molar Ratios ◽  
Ammonium Peroxydisulfate ◽  
Benzene Rings ◽  
Initial Ph ◽  
Anion Type

Aniline was oxidized with ammonium peroxydisulfate (APS) in aqueous solutions of various phenolic acids: 5-sulfosalicylic acid (SSA), 3,5-dinitrosalicylic acid (DNSA) and gallic acid (GA). Polymerizations were performed at the constant molar ratios [acid]/[aniline]=0.5 and [APS]/[aniline]=1.25. The conductivity of synthesized polyaniline (PANI) is affected by the dopant anion type and decreases in order: PANI-SSA > PANI-DNSA > PANI-GA, the last polymer being nonconducting. This decrease is in accordance with the increase of initial pH value of the reaction mixture. The differences in molecular structure of synthesized PANI have been revealed by FTIR spectroscopy. FTIR spectra of PANI-SSA and PANI-DNSA show typical features of PANI conductive emeraldine salt segments. On the contrary, FTIR spectrum of PANI-GA shows absence of bands typical for conducting PANI polaronic lattice, and indicates the higher oxidation state of this polymer than that of emeraldine, the presence of substituted phenazines as constitutional units, as well as significant content of monosubstituted benzene rings which reflects low polymerization degree and/or pronounced chain branching. The strong hydrogen bonding between GA and PANI can obstruct propagation of oligoanilines and formation of longer conducting PANI chains.

scholarly journals Synthesis of nanostructured conducting polyaniline in the presence of 5-sulfosalicylic acid

2008 ◽  
Vol 62 (3) ◽  
pp. 107-113 ◽  
Author(s):  
Aleksandra Janosevic ◽  
Gordana Ciric-Marjanovic
Keyword(s):  
Molecular Structure ◽  
Oxidative Polymerization ◽  
Average Diameter ◽  
Polymerization Process ◽  
Molar Ratio ◽  
Sulfosalicylic Acid ◽  
Molar Ratios ◽  
Reaction Solution ◽  
Initial Ph ◽  
Constant Molar Ratio

Oxidative polymerizations of aniline with ammonium peroxydisulfate in aqueous solution of 5-sulfosalicylic acid (SSA), were performed at the constant molar ratio [oxidant]/[monomer] = 1.25, by using various initial molar ratios of SSA to aniline. It was shown that the ratio [SSA]/[aniline] has a crucial influence on the molecular structure, morphology, and conductivity of synthesized polyaniline5-sulfosalicylate (PANI-SSA), as well as on the yield and temperature profile i.e. the mechanism of polymerization process. The yield of PANI-SSA was 80 - 86% for [SSA]/[aniline] ratios in the range 0.25-1.0. Granular PANI-SSA was obtained by the oxidative polymerization of in situ formed anilinium 5-sulfosalicylate ([SSA]/[aniline] = 1.0). The initial induction period was followed by the rapid exothermic polymerization of aniline during the oxidation of anilinium 5-sulfosalicylate with peroxydisulfate. Nanostructured PANI-SSA was synthesized by the oxidation of the mixture of dianilinium 5-sulfosalicylate and aniline ([SSA]/[aniline] = 0.25), which proceeds in two exothermic phases well separated with an athermal period. The presence of nanocylinders (nanorods, possibly nanotubes), with the average diameter of 95-250 nm and the length of 0.5-1.0 ?m has been revealed by scanning electron microscopy. It was concluded that PANI nanocylinders are formed when reaction solution has the initial pH > 3.5. Electroconductivity of synthesized polyanilines was in the range 0.01-0.17 S cm-1, and it increases with increasing molar ratio of SSA to aniline. Molecular structure of synthesized polyanilines was investigated by FTIR spectroscopy. Besides the characteristic bands of standard PANI in emeraldine form (benzenoid, quinonoid, and semiquinonoid units), the band attributable to substituted phenazine structural units was observed at -1415 cm-1 in the FTIR spectrum of nanostructured PANI-SSA sample.

scholarly journals Hydrothermal Synthesis of Various Shape-Controlled Europium Hydroxides

Nanomaterials ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 529
Author(s):  
Hongjuan Zheng ◽  
Kongjun Zhu ◽  
Ayumu Onda ◽  
Kazumichi Yanagisawa
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Ph Value ◽  
Hydrothermal Temperature ◽  
X Ray ◽  
Hydrothermal Reactions ◽  
Starting Solution ◽  
Initial Ph ◽  
Shape Controlled ◽  
Scanning Electron

Eu(OH)3 with various shape-controlled morphologies and size, such as plate, rod, tube, prism and nanoparticles was successfully synthesized through simple hydrothermal reactions. The products were characterized by XRD (X-Ray Powder Diffraction), FE-SEM (Field Emission- Scanning Electron Microscopy) and TG (Thermogravimetry). The influence of the initial pH value of the starting solution and reaction temperature on the crystalline phase and morphology of the hydrothermal products was investigated. A possible formation process to control morphologies and size of europium products by changing the hydrothermal temperature and initial pH value of the starting solution was proposed.

scholarly journals Optimizing the catalytic activities of methanol and thermotolerant Kocuria flava lipases for biodiesel production from cooking oil wastes

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Azhar Najjar ◽  
Elhagag Ahmed Hassan ◽  
Nidal Zabermawi ◽  
Saber H. Saber ◽  
Leena H. Bajrai ◽  
...  
Keyword(s):  
Ph Value ◽  
Energy Content ◽  
Value Added ◽  
Relative Activity ◽  
Economic Feasibility ◽  
Biodiesel Production ◽  
Molar Ratios ◽  
Cooking Oil ◽  
Enzyme Biocatalysis ◽  
Methanol Tolerant

AbstractIn this study, two highly thermotolerant and methanol-tolerant lipase-producing bacteria were isolated from cooking oil and they exhibited a high number of catalytic lipase activities recording 18.65 ± 0.68 U/mL and 13.14 ± 0.03 U/mL, respectively. Bacterial isolates were identified according to phenotypic and genotypic 16S rRNA characterization as Kocuria flava ASU5 (MT919305) and Bacillus circulans ASU11 (MT919306). Lipases produced from Kocuria flava ASU5 showed the highest methanol tolerance, recording 98.4% relative activity as well as exhibited high thermostability and alkaline stability. Under the optimum conditions obtained from 3D plots of response surface methodology design, the Kocuria flava ASU5 biocatalyst exhibited an 83.08% yield of biodiesel at optimized reaction variables of, 60 ○C, pH value 8 and 1:2 oil/alcohol molar ratios in the reaction mixture. As well as, the obtained results showed the interactions of temperature/methanol were significant effects, whereas this was not noted in the case of temperature/pH and pH/methanol interactions. The obtained amount of biodiesel from cooking oil was 83.08%, which was analyzed by a GC/Ms profile. The produced biodiesel was confirmed by Fourier-transform infrared spectroscopy (FTIR) approaches showing an absorption band at 1743 cm−1, which is recognized for its absorption in the carbonyl group (C=O) which is characteristic of ester absorption. The energy content generated from biodiesel synthesized was estimated as 12,628.5 kJ/mol. Consequently, Kocuria flava MT919305 may provide promising thermostable, methanol-tolerant lipases, which may improve the economic feasibility and biotechnology of enzyme biocatalysis in the synthesis of value-added green chemicals.

scholarly journals The sorption of inorganic arsenic on modified sepiolite: Effect of hydrated iron(III)-oxide

2014 ◽  
Vol 79 (7) ◽  
pp. 815-828 ◽  
Author(s):  
Nikola Ilic ◽  
Slavica Lazarevic ◽  
Vladana Rajakovic-Ognjanovic ◽  
Ljubinka Rajakovic ◽  
Djordje Janackovic ◽  
...  
Keyword(s):  
Sorption Capacity ◽  
Arsenic Removal ◽  
Ph Value ◽  
Inorganic Arsenic ◽  
Arsenic Species ◽  
Deionized Water ◽  
Order Kinetic ◽  
Initial Ph ◽  
Order Kinetic Model ◽  
Pseudo Second Order

The sorption of inorganic arsenic species, As(III) and As(V), from water by sepiolite modified with hydrated iron(III) oxide was investigated at 25 ?C through batch studies. The influence of the initial pH value, the initial As concentrations, the contact time and types of water on the sorption capacity was investigated. Two types of water were used, deionized and groundwater. The maximal sorption capacity for As(III) from deionized water was observed at initial and final pH value 7.0, while the bonding of As(V) was observed to be almost pH independent for pH value in the range from 2.0 to 7.0, and the significant decrease in the sorption capacity was observed at pH values above 7.0. The sorption capacity at initial pH 7.0 was about 10 mg g?1 for As(III) and 4.2 mg g?1 for As(V) in deionized water. The capacity in groundwater was decreased by 40 % for As(III) and by 20 % for As(V). The Langmuir model and pseudo-second order kinetic model revealed good agreement with the experimental results. The results show that Fe(III)-modified sepiolite exhibits significant affinity for arsenic removal and it has a potential for the application in water purification processes.

scholarly journals The Removal of Methylene Blue Dye from Aqueous Solutions Using Activated and Non-Activated Bentonites

2003 ◽  
Vol 21 (5) ◽  
pp. 451-462 ◽  
Author(s):  
Sameer Al-Asheh ◽  
Fawzi Banat ◽  
Leena Abu-Aitah
Keyword(s):  
Methylene Blue ◽  
Ph Value ◽  
Sodium Dodecyl ◽  
Freundlich Isotherm ◽  
Blue Dye ◽  
Batch Adsorption ◽  
Ionic Surfactant ◽  
Methylene Blue Dye ◽  
X Ray Diffraction ◽  
Initial Ph

An improvement in the adsorption capacity of naturally available bentonite towards water pollutants such as Methylene Blue dye (MBD) is certainly needed. For this purpose, sodium bentonite was activated by two methods: (1) treatment with sodium dodecyl sulphate (SDS) as an ionic surfactant and (2) thermal treatment in an oven operated at 850°C. Batch adsorption tests were carried out on removing MBD from aqueous solution using the above-mentioned bentonites. It was found that the effectiveness of bentonites towards MBD removal was in the following order: thermal-bentonite > SDS-bentonite > natural bentonite. X-Ray diffraction analysis showed that an increase in the microscopic bentonite platelets on treatment with SDS was the reason behind the higher uptake of MBD. An increase in sorbent concentration or initial pH value of the solutions resulted in a greater removal of MBD from the solution. An increase in temperature led to an increase in MBD uptake by the bentonites studied in this work. The Freundlich isotherm model was employed and found to represent the experimental data well.

High Cr(VI) Adsorption Performance of Coal-Based Activated Carbon in Aqueous Solution

2013 ◽  
Vol 798-799 ◽  
pp. 1123-1127
Author(s):  
Hua Lei Zhou ◽  
Qiong Qiong Zhu ◽  
Dong Hua Huang
Keyword(s):  
Aqueous Solution ◽  
Activated Carbon ◽  
Pore Structure ◽  
Ph Value ◽  
High Surface ◽  
High Surface Area ◽  
Koh Activation ◽  
Transmission Electron ◽  
Mesoporous Adsorbent ◽  
Initial Ph

The activated carbon with high surface area was prepared by KOH activation from anthracite and used as adsorbent for removal of Cr (VI) from aqueous solution. The pore structure and surface properties were characterized by N2 adsorption at 77K, transmission electron microscope (TEM) and Fourier transform infrared spectroscopy ( FTIR). Effect of pH and isotherms at different temperature were investigated. Results show that the prepared carbon is a microporous-and mesoporous-adsorbent with developed pore structure and abundant surface oxygen-containing groups. PH value of the solution plays key function on the adsorption. The chemical adsorption dominates the adsorption process. The activated carbon exhibits much higher Cr adsorption capacity than the commercial activated carbon at initial pH of ~3. The equilibrium adsorption data are fitted by both Freundlich model and Langmuir model well.

scholarly journals Comparison between Different Keratin-composed Biosorbents for the Removal of Heavy Metal Ions from Aqueous Solutions

2002 ◽  
Vol 20 (4) ◽  
pp. 393-416 ◽  
Author(s):  
Fawzi Banat ◽  
Sameer Al-Asheh ◽  
Dheaya‘ Al-Rousan
Keyword(s):  
Aqueous Solutions ◽  
Human Hair ◽  
Metal Ion ◽  
Ph Value ◽  
Freundlich Isotherm ◽  
Operating Conditions ◽  
Ion Uptake ◽  
Chicken Feathers ◽  
Initial Ph ◽  
Metal Ion Uptake

This study examined and compared the ability of chicken feathers, human hair and animal horns, as keratin-composed biosorbents, for the removal of Zn2+ and Cu2+ ions from single metal ion aqueous solutions under different operating conditions. The three biosorbents investigated in this study were all capable of adsorbing Zn2+ and Cu2+ ions from aqueous solutions. The biosorbent showing the highest uptake of Zn2+ and Cu2+ ions was animal horns. Chicken feathers showed a higher Cu2+ ion uptake and a lower Zn2+ ion compared to human hair. Increasing the initial concentration of Zn2+ or Cu2+ ions, or increasing the initial pH value, increased the metal ion uptake. Such uptake decreased when the temperature was raised from 25°C to 50°C for all adsorbent/metal ion combinations except for Zn2+ ion/human hair where the uptake increased with temperature. It was demonstrated that the addition of NaCl salt to the metal ion solution depressed the metal ion uptake. The Freundlich isotherm model was found to be applicable to the adsorption data for Cu2+ and Zn2+ ions.

The Study about Environmentally-Friendly Passivation Technology Process and Performance on Brass Surface

2011 ◽  
Vol 399-401 ◽  
pp. 1967-1971
Author(s):  
Hong Yin Xu ◽  
Li Li
Keyword(s):  
Corrosion Resistance ◽  
Phytic Acid ◽  
Passive Film ◽  
Ph Value ◽  
Sodium Molybdate ◽  
Solution Ph ◽  
Sulfosalicylic Acid ◽  
Passivation Film ◽  
Brass Surface ◽  
And Performance

The paper through the synergy before mixed Phytic acid and Sodium molybdate, Sulfosalicylic acid, Organic silane, and add the active substances PEG, Optimize the Passivation liquid formula of Brass surface, Phytic acid is the main ingredient, study the affection of Phytic acid Passive film Corrosion resistance on the three main Passivation conditions: Passivation temperature, time and Passivation solution PH value. The results show that，Phytic acid passivation film process recipes as follows：Phytic acid (quality score 50%) 2~5ml/L, sodium molybdate 4~8g/L, organic material 10~30ml/L, sulfosalicylic acid 3~7g/L, polyethylene glycol 2~6g/L, deactivated temperature 30~35°C, pH value 5, deactivated time 60s. The test showed that，the phytic acid passive film can obviously enhance the anti-corrosive performance on the brass surface, its corrosion resistance proportion chromates passive film is fairly good.

Screening and Desilication of a Silicate Bacteria

2011 ◽  
Vol 236-238 ◽  
pp. 253-257
Author(s):  
Xian Zhen Zhang ◽  
De Si Sun ◽  
Hai Lin
Keyword(s):  
Particle Size ◽  
Incubation Time ◽  
Ph Value ◽  
Solution Temperature ◽  
Optimum Conditions ◽  
Initial Ph ◽  
Silicate Bacteria ◽  
Bauxite Ore

The strain Jgj-1 was isolated from Gaoan bauxite ore. The relations of desilication of the strain Jgj-1 and the pH of solution, temperature, shaking speed, incubation time, particle size were investigated. The results shows the optimum conditions of bioleaching are as following: at 28°C, initial pH value is 7.2, particle size 0.056mm, 200rpm shaking speed, incubation 5-7 days.

scholarly journals Biogas Production from Combined Irish Potato and Poultry Wastes: Optimization and Kinetic Studies

2018 ◽  
Vol 7 (3.36) ◽  
pp. 170
Author(s):  
Umar M. Ibrahim ◽  
Saeed I. Ahmed ◽  
Babagana Gutti ◽  
Idris M. Muhammad ◽  
Usman D. Hamza ◽  
...  
Keyword(s):  
Anaerobic Digestion ◽  
Kinetic Parameters ◽  
Ph Value ◽  
Biogas Production ◽  
Irish Potato ◽  
Coefficient Of Determination ◽  
Optimum Conditions ◽  
Biogas Yield ◽  
Potato Waste ◽  
Initial Ph

The combination of Irish potato waste (IPW) and poultry waste (PW) can form a synergy resulting into an effective substrate for a better biogas production due to some materials they contain. In this work, optimization and kinetic study of biogas production from anaerobic digestion of IPW and PW was investigated. Response surface methodology (RSM) was applied to optimize conditions such as initial pH, solids concentrations and waste ratios. The anaerobic digestion of the two wastes was carried out in the mesophilic condition and Box-Behnken design (BBD) was used to develop and analyze a predictive model which describes the biogas yield. The results revealed that there is a good fit between the experimental and the predicted biogas yield as revealed by the coefficient of determination (R2) value of 97.93%. Optimization using quadratic RSM predicts biogas yield of 19.75% at the optimal conditions of initial pH value 7.28, solids concentration (w/v) 9.85% and waste ratio (IPW:PW) 45:55%. The reaction was observed to have followed a first order kinetics having R2 and relative squared error (RSE) values of 90.61 and 9.63% respectively. Kinetic parameters, such as rate constant and half-life of the biogas yield were evaluated at optimum conditions to be 0.0392 day-1 and 17.68 days respectively. The optimum conditions and kinetic parameters generated from this research can be used to design real bio-digesters, monitor substrate concentrations, simulate biochemical processes and predict performance of bio-digesters using IPW and PW as substrate.  

Sign in / Sign up

Export Citation Format

Share Document