scholarly journals Experimental testing of the digital multichannel analyzer for gamma spectrometry measurements

2008 ◽  
Vol 23 (1) ◽  
pp. 43-46 ◽  
Author(s):  
Dusan Novkovic ◽  
Laslo Nadjdjerdj ◽  
Aleksandar Kandic ◽  
Ivana Vukanac ◽  
Mirjana Djurasevic
Keyword(s):  
Experimental Testing ◽  
Peak Position ◽  
Automatic Tuning ◽  
Multichannel Analyzer ◽  
Time Correction ◽  
The Stability ◽  
Two Peaks ◽  
Full Peak ◽  
Optimum Measurement

The results of experimental testing of the digital multichannel analyzer which digitalizes the signal after a preamplifier are presented. The recordings of some of the characteristics of the spectrometer containing a digital MCA, such as full-peak efficiency, net area ratio of the two peaks and the stability of the peak position, were carried out under different input counting rates, with different radioactive sources. The tested MCA has shown some excellent features, like the stability of the peak position over a long-term period and flexibility in the adjusting of optimum measurement conditions. However, the performed tests have also shown some serious and unexpected disadvantages of the digital MCA when it operates under certain circumstances, one of them having to do with the automatic tuning of live-time correction at low-input counting rates.

Comparative Analysis of the Effect of Immersion of Porous Silicon in Aqueous Solutions of Li and Fe Salts on the Stability, Peak Position and Intensity of its Photoluminescence

2018 ◽  
Vol 386 ◽  
pp. 75-79
Author(s):  
Nikolay G. Galkin ◽  
Dmitrii Tkhyarbonovich Yan ◽  
Konstantin N. Galkin ◽  
Evgeniy Anatolievich Chusovitin ◽  
Mikhail Victorovich Bozhenko
Keyword(s):  
Porous Silicon ◽  
Aqueous Solutions ◽  
Blue Shift ◽  
Peak Position ◽  
Maximum Increase ◽  
Long Term Storage ◽  
Low Concentrations ◽  
The Stability ◽  
Term Storage

In the process of comparative studies of immersing layers of porous silicon (PS) in aqueous solutions of LiBr and Fe (NO3)3 with subsequent long-term storage up to 150 days, it is established that there exists: (1) the range of concentrations of LiBr (S/2 - S/4) and Fe (NO3)3 (0.2 M), which provide the maximum increase in the intensity of PL; (2) at low concentrations of both salts, a blue shift of the PL peaks and an increase in their intensity are observed during the long-term storage, which is associated with a decrease in the size of the NC in the PS and the influence of silicon bonds with lithium or iron ions; (3) full protection of the PS layer is observed in case of immersion in Fe (NO3)3 with a concentration of 0.7M - 0.8M.

Quality of Reamed Surface Using Serrated Blades as Compared to a Conventional Acetabular Reamer

2013 ◽  
Author(s):  
Annie Levasseur ◽  
Jérémie Ménard ◽  
Victor Songmené ◽  
Julio Fernandes ◽  
Yvan Petit
Keyword(s):  
Experimental Testing ◽  
Three Dimensional ◽  
Laser Scanner ◽  
Numerical Control ◽  
Long Term Stability ◽  
Surface Irregularities ◽  
The Stability ◽  
Acetabular Implant

Background: Hip arthroplasty requires the preparation of the acetabular cavity to allow a proper contact between the bone and the implant. It is essential to allow osseointegration and long-term stability of the implant. The aim of this study was to conduct experimental testing to evaluate the quality of reamed surfaces using a serrated blade acetabular reamer as compared to a conventional rasp reamer. Method of Approach: Reaming tests were performed on a computerized numerical control tools machine at a rotational speed of 250 rpm and 3 different penetration speeds: 0.20 mm/s, 0.55 mm/s and 0.90 mm/s. For each reamer, a complete semi-hemispherical hole was perforated in 7 polyurethane samples. The reamed surfaces were digitized with a three-dimensional high resolution (40 μm) self-positioning laser scanner to carry out a quantitative analysis of the surface quality. Results: Results demonstrated that the cutting edge and the penetration speed influence the quality of the reamed surface. The serrated blade was found to reduce surface irregularities (ranging between 0.19 mm to 0.21 mm for the conventional rasp and between 0.07 mm and 0.12 mm for the serrated blades), and to reduce inaccuracies on the reamed cavity diameter (0.13 mm ± 0.05mm for the rasps and 0.06 mm ± 0.03mm for the serrated blade). Conclusions: The use of such tool by the surgeon may influence the stability of the acetabular implant and reduce the risks of revision surgery.

scholarly journals Effect of Rainfall, Runoff and Infiltration Processes on the Stability of Footslopes

Water ◽  
2020 ◽  
Vol 12 (5) ◽  
pp. 1229
Author(s):  
Hung-En Chen ◽  
Yen-Yu Chiu ◽  
Tung-Lin Tsai ◽  
Jinn-Chuang Yang
Keyword(s):  
Slope Failure ◽  
Limit Equilibrium ◽  
Limit Equilibrium Method ◽  
Peak Position ◽  
Shallow Landslides ◽  
Rainfall Runoff ◽  
One Dimensional ◽  
Landslide Modeling ◽  
The Stability

To analyze the effect of runoff on shallow landslides, a model coupling one-dimensional rainfall–runoff and two-dimensional infiltration was established to simulate rainfall, infiltration, and runoff processes. Based on Bishop’s limit equilibrium method, the slope failure of a hypothetical footslope was studied. First, conditions with and without inflow were compared. The results reveal a remarkable difference in factors of safety (FS) between the two conditions, suggesting that considering the effect of runoff is crucial for landslide modeling. In terms of a series of tests of the various magnitudes, durations, lag-time, and peak position of the hydrograph, analyses show that larger inflow leads to more accumulated infiltration and triggers landslides earlier. A long-term duration inflow decreases the stability more than short intensive inflow does. With subsequent surface inflow, slope failure may occur after rainfalls stop, owing to the inflow, and the shape of inflow hydrographs could slightly affect the variance in FS. Results also indicate the necessity of considering the surface runoff when using a numerical model to analyze landslide, particularly on a footslope.

The Stability of the WHO Reference Thromboplastin NIBS & C 67/40

1979 ◽  
Vol 42 (04) ◽  
pp. 1135-1140 ◽  
Author(s):  
G I C Ingram
Keyword(s):  
Human Brain ◽  
Collaborative Study ◽  
Calibration Constant ◽  
Long Term Stability ◽  
Freeze Dried ◽  
Show Evidence ◽  
Human Material ◽  
Reference Preparation ◽  
The Stability

SummaryThe International Reference Preparation of human brain thromboplastin coded 67/40 has been thought to show evidence of instability. The evidence is discussed and is not thought to be strong; but it is suggested that it would be wise to replace 67/40 with a new preparation of human brain, both for this reason and because 67/40 is in a form (like Thrombotest) in which few workers seem to use human brain. A �plain� preparation would be more appropriate; and a freeze-dried sample of BCT is recommended as the successor preparation. The opportunity should be taken also to replace the corresponding ox and rabbit preparations. In the collaborative study which would be required it would then be desirable to test in parallel the three old and the three new preparations. The relative sensitivities of the old preparations could be compared with those found in earlier studies to obtain further evidence on the stability of 67/40; if stability were confirmed, the new preparations should be calibrated against it, but if not, the new human material should receive a calibration constant of 1.0 and the new ox and rabbit materials calibrated against that.The types of evidence available for monitoring the long-term stability of a thromboplastin are discussed.

Application of the method of mathematical modeling for forecasting channel deformations at the underwater crossing of the main pipeline

2020 ◽  
Vol 10 (6) ◽  
pp. 599-609
Author(s):  
Valery А. Gruzdev ◽  
◽  
Georgy V. Mosolov ◽  
Ekaterina A. Sabayda ◽  
◽  
...  
Keyword(s):  
Mathematical Modeling ◽  
Mathematical Model ◽  
Roughness Coefficient ◽  
Computational Domain ◽  
Channel Deformations ◽  
Geological Surveys ◽  
Kuban River ◽  
The Stability ◽  
Protective Structures

In order to determine the possibility of using the method of mathematical modeling for making long-term forecasts of channel deformations of trunk line underwater crossing (TLUC) through water obstacles, a methodology for performing and analyzing the results of mathematical modeling of channel deformations in the TLUC zone across the Kuban River is considered. Within the framework of the work, the following tasks were solved: 1) the format and composition of the initial data necessary for mathematical modeling were determined; 2) the procedure for assigning the boundaries of the computational domain of the model was considered, the computational domain was broken down into the computational grid, the zoning of the computational domain was performed by the value of the roughness coefficient; 3) the analysis of the results of modeling the water flow was carried out without taking the bottom deformations into account, as well as modeling the bottom deformations, the specifics of the verification and calibration calculations were determined to build a reliable mathematical model; 4) considered the possibility of using the method of mathematical modeling to check the stability of the bottom in the area of TLUC in the presence of man-made dumping or protective structure. It has been established that modeling the flow hydraulics and structure of currents, making short-term forecasts of local high-altitude reshaping of the bottom, determining the tendencies of erosion and accumulation of sediments upstream and downstream of protective structures are applicable for predicting channel deformations in the zone of the TLUC. In all these cases, it is mandatory to have materials from engineering-hydro-meteorological and engineering-geological surveys in an amount sufficient to compile a reliable mathematical model.

Influence of internal and external risks on sustainability of financial system of Аltai krai

2018 ◽  
Vol 35 (4) ◽  
pp. 133-136
Author(s):  
R. N. Ibragimov
Keyword(s):  
Sustainable Development ◽  
Financial Stability ◽  
Management Strategy ◽  
Financial System ◽  
Risk Management Strategy ◽  
The Sustainable Development ◽  
The Stability ◽  
The Impact

The article examines the impact of internal and external risks on the stability of the financial system of the Altai Territory. Classification of internal and external risks of decline, affecting the sustainable development of the financial system, is presented. A risk management strategy is proposed that will allow monitoring of risks, thereby these measures will help reduce the loss of financial stability and ensure the long-term development of the economy of the region.

Long-term vegetation restoration promotes the stability of the soil micro-food web in the Loess Plateau in North-west China

CATENA ◽  
2021 ◽  
Vol 202 ◽  
pp. 105293
Author(s):  
Yang Wu ◽  
WenJing Chen ◽  
Wulan Entemake ◽  
Jie Wang ◽  
HongFei Liu ◽  
...  
Keyword(s):  
Food Web ◽  
Loess Plateau ◽  
Vegetation Restoration ◽  
The Loess Plateau ◽  
West China ◽  
North West ◽  
The Stability

scholarly journals An unusually low density ultra-short period super-Earth and three mini-Neptunes around the old star TOI-561

2020 ◽  
Author(s):  
G Lacedelli ◽  
L Malavolta ◽  
L Borsato ◽  
G Piotto ◽  
D Nardiello ◽  
...  
Keyword(s):  
Transit Time ◽  
Time Variation ◽  
Planetary System ◽  
Radial Velocities ◽  
Low Density ◽  
Outer Planets ◽  
Short Period ◽  
The Stability

Abstract Based on HARPS-N radial velocities (RVs) and TESS photometry, we present a full characterisation of the planetary system orbiting the late G dwarf After the identification of three transiting candidates by TESS, we discovered two additional external planets from RV analysis. RVs cannot confirm the outer TESS transiting candidate, which would also make the system dynamically unstable. We demonstrate that the two transits initially associated with this candidate are instead due to single transits of the two planets discovered using RVs. The four planets orbiting TOI-561 include an ultra-short period (USP) super-Earth (TOI-561 b) with period Pb = 0.45 d, mass Mb = 1.59 ± 0.36 M⊕ and radius Rb = 1.42 ± 0.07 R⊕, and three mini-Neptunes: TOI-561 c, with Pc = 10.78 d, Mc = 5.40 ± 0.98 M⊕, Rc = 2.88 ± 0.09 R⊕; TOI-561 d, with Pd = 25.6 d, Md = 11.9 ± 1.3 M⊕, Rd = 2.53 ± 0.13 R⊕; and TOI-561 e, with Pe = 77.2 d, Me = 16.0 ± 2.3 M⊕, Re = 2.67 ± 0.11 R⊕. Having a density of 3.0 ± 0.8 g cm−3, TOI-561 b is the lowest density USP planet known to date. Our N-body simulations confirm the stability of the system and predict a strong, anti-correlated, long-term transit time variation signal between planets d and e. The unusual density of the inner super-Earth and the dynamical interactions between the outer planets make TOI-561 an interesting follow-up target.

scholarly journals Effect of Photoinitiator on Precursory Stability and Curing Depth of Thiol-Ene Clickable Gelatin

Polymers ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1877
Author(s):  
Kai-Hung Yang ◽  
Gabriella Lindberg ◽  
Bram Soliman ◽  
Khoon Lim ◽  
Tim Woodfield ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Visible Light ◽  
Rheological Properties ◽  
Swelling Ratio ◽  
Sodium Persulfate ◽  
Photo Polymerization ◽  
Gelation Kinetics ◽  
The Stability ◽  
Over Time

Recent advances highlight the potential of photopolymerizable allylated gelatin (GelAGE) as a versatile hydrogel with highly tailorable properties. It is, however, unknown how different photoinitiating system affects the stability, gelation kinetics and curing depth of GelAGE. In this study, sol fraction, mass swelling ratio, mechanical properties, rheological properties, and curing depth were evaluated as a function of time with three photo-initiating systems: Irgacure 2959 (Ig2959; 320–500 nm), lithium phenyl-2,4,6-trimethylbenzoylphosphinate (LAP; 320–500 nm), and ruthenium/sodium persulfate (Ru/SPS; 400–500 nm). Results demonstrated that GelAGE precursory solutions mixed with either Ig2959 or LAP remained stable over time while the Ru/SPS system enabled the onset of controllable redox polymerization without irradiation during pre-incubation. Photo-polymerization using the Ru/SPS system was significantly faster (<5 s) compared to both Ig2959 (70 s) and LAP (50 s). Plus, The Ru/SPS system was capable of polymerizing a thick construct (8.88 ± 0.94 mm), while Ig2959 (1.62 ± 0.49 mm) initiated hydrogels displayed poor penetration depth with LAP (7.38 ± 2.13 mm) in between. These results thus support the use of the visible light based Ru/SPS photo-initiator for constructs requiring rapid gelation and a good curing depth while Ig2959 or LAP can be applied for photo-polymerization of GelAGE materials requiring long-term incubation prior to application if UV is not a concern.

scholarly journals Carrier-microencapsulation using Al-catecholate complex to suppress arsenopyrite oxidation: Evaluation of the coating stability under simulated weathering conditions

2019 ◽  
Vol 268 ◽  
pp. 06002 ◽  
Author(s):  
Kensuke Seno ◽  
Ilhwan Park ◽  
Carlito Tabelin ◽  
Kagehiro Magaribuchi ◽  
Mayumi Ito ◽  
...  
Keyword(s):  
Protective Coating ◽  
Sulfide Mineral ◽  
Sulfide Minerals ◽  
Low Ph ◽  
Oxidation Products ◽  
Arsenic Sulfide ◽  
Catecholate Complex ◽  
Coating Stability ◽  
The Stability

Arsenopyrite (FeAsS) is the most common primary arsenic-sulfide mineral in nature, and its oxidation causes the release of toxic arsenic (As). To mitigate these problems, carrier-microencapsulation (CME), a technique that passivates sulfide minerals by covering their surfaces with a protective coating, has been developed. In the previous study of authors on CME, Al-catecholate complex significantly suppressed arsenopyrite oxidation via electron donating effects of the complex and the formation of an Al-oxyhydroxide coating. For the application of this technique to real tailings, however, further study should be carried out to elucidate long-term effectiveness of the coating to suppress arsenopyrite oxidation. This study investigates the stability of the coating formed on arsenopyrite by Al-based CME using weathering tests. The Al-oxyhydroxide coating suppressed arsenopyrite oxidation until about 50 days of the experiment, but after this, the amounts of oxidation products like dissolved S and As increased due to the gradual dissolution of the coating with time as a result of the low pH of leachate. This suggests that co-disposal of Al-based CME-treated arsenopyrite with minerals that have appropriate neutralization potentials, so that the pH is maintained at around 5 to 8 where Al-oxyhydroxide is stable.

Sign in / Sign up

Export Citation Format

Share Document