scholarly journals Effect of Orientation Angle on Surface Quality and Dimensional Accuracy of Functional Parts Manufactured by Multi Jet Fusion Technology

2020 ◽  
Vol 4 (2) ◽  
pp. 47-52
Author(s):  
Binnur SAĞBAŞ
Keyword(s):  
Surface Quality ◽  
Orientation Angle ◽  
Dimensional Accuracy ◽  
Fusion Technology

Research Status of Subsequent Machining of Laser Cladding Layers

2020 ◽  
Vol 15 ◽  
Author(s):  
Lei Li ◽  
Yujun Cai ◽  
Guohe Li ◽  
Meng Liu
Keyword(s):  
Tool Wear ◽  
Surface Quality ◽  
Laser Cladding ◽  
Wear Surface ◽  
Chip Formation ◽  
Cutting Temperature ◽  
Dimensional Accuracy ◽  
Cutting Parameters ◽  
Cladding Layer ◽  
Cladding Layers

Background: As an important method of remanufacturing, laser cladding can be used to obtain the parts with specific shapes by stacking materials layer by layer. The formation mechanism of laser cladding determines the “Staircase effect”, which makes the surface quality can hardly meet the dimensional accuracy of the parts. Therefore, the subsequent machining must be performed to improve the dimensional accuracy and surface quality of cladding parts. Methods: In this paper, chip formation, cutting force, cutting temperature, tool wear, surface quality, and optimization of cutting parameters in the subsequent cutting of laser cladding layer are analyzed. Scholars have expounded and studied these five aspects but the cutting mechanism of laser cladding need further research. Results: The characteristics of cladding layer are similar to that of difficult to machine materials, and the change of parameters has a significant impact on the cutting performance. Conclusion: The research status of subsequent machining of cladding layers is summarized, mainly from the aspects of chip formation, cutting force, cutting temperature, tool wear, surface quality, and cutting parameters optimization. Besides, the existing problems and further developments of subsequent machining of cladding layers are pointed out. The efforts are helpful to promote the development and application of laser cladding remanufacturing technology.

Flexibles robotergeführtes Dornhonen*/Flexible, robot guided single-pass honing - Flexible honing of geometrically complex workpieces in small and medium lot size production

2015 ◽  
Vol 105 (06) ◽  
pp. 360-365
Author(s):  
E. Uhlmann ◽  
S. Zimmermann
Keyword(s):  
Surface Quality ◽  
Tribological Properties ◽  
Industrial Robot ◽  
Dimensional Accuracy ◽  
Lot Size ◽  
Flexible Robot ◽  
Single Pass ◽  
Machining Center ◽  
Geometrically Complex ◽  
Flexible Honing

Das Fertigungsverfahren Honen kommt zur Anwendung, wenn an Bauteile hohe Anforderungen hinsichtlich Form- und Maßgenauigkeit, Oberflächenqualität sowie tribologische Eigenschaften gestellt werden. Insbesondere das Honen von Bauteilen mit Bohrungen in verschiedenen Positionen und Winkellagen stellt eine Herausforderung dar. Mithilfe eines 6-Achs-Industrieroboters wurde ein Verdichtergehäuse in W-Bauform bearbeitet. Anschließend wurden die Arbeitsergebnisse mit konventionell gefertigten Bauteilen verglichen.   In manufacturing, honing is used to meet high demands on shape and dimensional accuracy, surface quality, as well as tribological properties. In particular, the honing of workpieces with bore holes in various positions and angles represents a challenge. With the help of a six-axis industrial robot, a W-shaped compressor housing was machined and working results were compared with results produced on a machining center.

scholarly journals Effects of Sintering Behaviors on Dimensional Accuracy, Surface Quality, and Mechanical Properties of Stereolithography-printed 3Y-ZrO2 Ceramics

2021 ◽  
Author(s):  
Cheng Zhang ◽  
Zhaoliang Jiang ◽  
Li Zhao ◽  
Weiwei Guo ◽  
Chengpeng Zhang
Keyword(s):  
Mechanical Properties ◽  
Dental Implants ◽  
Surface Quality ◽  
Dimensional Accuracy ◽  
Scanning Speed ◽  
Sintering Process ◽  
X Ray Diffraction ◽  
Air Atmosphere ◽  
Length Width ◽  
Technical Guide

Abstract Sintering process is essential to acquire the final components by stereolithography (SLA), which is a promising additive manufacturing technology for the fabrication of complex, custom-designed dental implants. 3Y-ZrO2 ceramics at different sintering behaviors in air atmosphere were successfully obtained in this study. Firstly, the curing properties of homemade pastes were studied, and the penetration depth and critical exposure of the pastes were calculated as 17.2 μm and 4.80 mJ/cm2, respectively. The green ceramic parts were performed at 154 mW laser power and 6000 mm/s scanning speed. Then, the dimensional accuracy, surface quality, and mechanical properties of 3Y-ZrO2 ceramics were investigated. The shrinkages of length, width, and height were 26%~27 %, 30%~31 %, and 27%~33 % in sintered ceramics, respectively. The Ra values of XOY, YOZ, and XOZ surfaces showed an anisotropic feature, and they were smallest as 0.52 μm, 2.40 μm, and 2.46 μm, respectively. Meanwhile, the mechanical properties presented a similar trend that they grew first and then dropped at various sintering behaviors. The optimal parameters were 1500 ℃, 60 min, and 4 ℃/min, and the maximum relative density of 96.18 %, Vickers hardness of 12.45 GPa, and fracture toughness of 6.35 MPa·m1/2 were achieved. Finally, the X-ray diffraction (XRD) and energy-dispersive spectroscopy (EDS) analysis demonstrated that no change was observed in crystal transformation and phase composition, and the organic was completely removed in sintered ceramics. This research is expected to provide a technical guide for the fabrication of ceramics for dental implants using SLA technique.

Influence of Manufacturing Process on the Fatigue Strength of Gears

2014 ◽  
Vol 1018 ◽  
pp. 269-276
Author(s):  
Andrea Reiß ◽  
Ulf Engel
Keyword(s):  
Fatigue Strength ◽  
Surface Quality ◽  
Fatigue Behavior ◽  
High Surface ◽  
Research Work ◽  
Dimensional Accuracy ◽  
Cold Forging ◽  
Hardness Distribution ◽  
Forming Process ◽  
High Surface Quality

With cold forging processes it is possible to produce parts characterized by high strength, high dimensional accuracy and high surface quality. In order to optimize the forming process and to be able to use the advantages of cold forging specifically and combined, it is necessary to find correlations between manufacturing parameters on the one side, strength and other properties like hardness distribution and surface quality of the component on the other side. The research work covered in this paper focuses on the correlation of the components properties influenced by its manufacturing history and their fatigue strength. The used component is a gear produced by a lateral cold forging process. For the investigations an experimental setup has been designed. The aim for the design of the setup is to reproduce the real contact condition for the contact of two gears. To obtain different component properties the production process of the gear was varied by producing the parts by a milling operation. First of all, the components’ properties, for example hardness distribution, remaining residual stresses, orientation of fibers and surface quality, were determined. The components’ fatigue behavior was determined using a high frequency pulsator and evaluated in terms of finite life fatigue strength and fatigue endurance limit. These examinations were used to produce Woehler curves for the differently manufactured components with a certain statistical data analysis method.

Experimental study on the accuracy and surface quality of printed versus machined holes in PEI Ultem 9085 FDM specimens

2021 ◽  
Vol 27 (11) ◽  
pp. 1-12
Author(s):  
Giovanni Gómez-Gras ◽  
Marco A. Pérez ◽  
Jorge Fábregas-Moreno ◽  
Guillermo Reyes-Pozo
Keyword(s):  
Surface Quality ◽  
Fused Deposition Modeling ◽  
Three Dimensional ◽  
Dimensional Accuracy ◽  
Technological Parameters ◽  
Content Type ◽  
Fused Deposition ◽  
Comparison Of The Results ◽  
Through Hole

Purpose This paper aims to investigate the quality of printed surfaces and manufacturing tolerances by comparing the cylindrical cavities machined in parts obtained by fused deposition modeling (FDM) with the holes manufactured during the printing process itself. The comparison focuses on the results of roughness and tolerances, intending to obtain practical references when making assemblies. Design/methodology/approach The experimental approach focuses on the comparison of the results of roughness and tolerances of two manufacturing strategies: geometric volumes with a through-hole and the through-hole machined in volumes that were initially printed without the hole. Throughout the study, both alternates are explained to make appropriate recommendations. Findings The study shows the best combinations of technological parameters, both machining and three-dimensional printing, which have been decisive for obtaining successful results. These conclusive results allow enunciating recommendations for use in the industrial environment. Originality/value This paper fulfills an identified need to study the dimensional accuracy of the geometries obtained by additive manufacturing, as no experimental evidence has been found of studies that directly address the problem of the FDM-printed part with geometric and dimensional tolerances and desirable surface quality for assembly.

Characterization of Cutting-Induced Heat Generation in Ultra-Precision Milling of Aluminium Alloy 6061

2013 ◽  
Vol 552 ◽  
pp. 201-206
Author(s):  
Su Juan Wang ◽  
Suet To ◽  
Xin Du Chen
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Heat Generation ◽  
Feed Rate ◽  
Dimensional Accuracy ◽  
Precision Machining ◽  
Machined Surface ◽  
Single Crystal Diamond ◽  
Ultra Precision ◽  
Alloy 6061

The technology of ultra-precision machining with single crystal diamond tool produces advanced components with higher dimensional accuracy and better surface quality. The cutting-induced heat results in high temperature and stress at the chip-tool and tool-workpiece interfaces therefore affects the materials and the cutting tool as well as the surface quality. In the ultra-precision machining of al6061, the cutting-induced heat generates precipitates on the machined surface and those precipitates induce imperfections on the machined surface. This paper uses the time-temperature-precipitation characteristics of aluminum alloy 6061 (al6061) to investigate the effect of feed rate on the cutting-induced heat generation in ultra-precision multi-axis milling process. The effect of feed rate and feed direction on the generation of precipitates and surface roughness in ultra-precision raster milling (UPRM) is studied. Experimental results show that heat generation in horizontal cutting is less than that in vertical cutting and a larger feed rate generates more heat on the machined workpiece. A smaller feed rate produces a better surface finish and under a larger feed rate, scratch marks are produced by the generated precipitates and increase surface roughness.

Scratching Experimental Research on Critical Cut Depth of Glass BK7

2013 ◽  
Vol 589-590 ◽  
pp. 194-197 ◽  
Author(s):  
Peng Jia
Keyword(s):  
Surface Quality ◽  
Optical Glass ◽  
Dimensional Accuracy ◽  
Cutting Fluid ◽  
Dry Cutting ◽  
Diamond Cutting ◽  
Fluid Properties ◽  
Indentation Experiment ◽  
Cut Depth

For the technology of diamond cutting of optical glass, the machinability of glass is poor, which hindering the practical application of this technology. In order to investigate and ameliorate the machinability of glass, and achieve optical parts with the satisfied surface quality and dimensional accuracy, this paper first conducted SF6 indentation experiment by Vickers microhardness instrument, and then the scratching tests with increasing depths of cut were conducted on glass SF6 to evaluate the influence of the cutting fluid properties on the machinability of glass. Based on this, turning tests were carried out, and the surface quality of SF6 was assessed based on the detections of the machined surfaces roughness. Experimental results indicated that compared with the process of dry cutting, the machinability of glass SF6 can be improved by using the cutting fluid

scholarly journals Combination of Laser Material Deposition and Laser Surface processes for the manufacture of sculptured surface components

2018 ◽  
Author(s):  
Jon Iñaki Arrizubieta ◽  
Magdalena Cortina ◽  
Jose Exequiel Ruiz ◽  
Aitzol Lamikiz
Keyword(s):  
Surface Quality ◽  
Dimensional Accuracy ◽  
Laser Machining ◽  
Additive Process ◽  
Laser Polishing ◽  
Material Deposition ◽  
Laser Heat Source ◽  
Near Net Shape ◽  
Machining Operations

The present work proposes a novel manufacturing technique based on the combination of Laser Metal Deposition, Laser Beam Machining and Laser Polishing processes for the complete manufacturing of complex parts. Therefore, the complete process is based on the application of a laser heat source both for the building of the preform shape of the part by additive manufacturing and for the finishing operations. Their combination enables to manufacture near-net-shape parts and afterwards, remove the excess material via laser machining, which has resulted to be capable of eliminating the waviness resulting from the additive process. Besides, surface quality is improved via laser polishing to reduce the roughness of the final part. Therefore, conventional machining operations are eliminated, what results in a much cleaner process. In order to validate the capability of this new approach, the dimensional accuracy and surface quality of the resulting parts are evaluated. The process has been validated on an Inconel 718 test part, where a previously additively built up part has been finished by means of laser machining and laser polishing.

Barrel Chamber Polishing, Using Electrochemical Theories

2007 ◽  
Vol 364-366 ◽  
pp. 272-279
Author(s):  
Ramezan Ali Mahdavinejad
Keyword(s):  
Surface Quality ◽  
High Surface ◽  
Dimensional Accuracy ◽  
Point Of View ◽  
Electrochemical Polishing ◽  
Machining Time ◽  
High Surface Quality ◽  
Surface Polishing ◽  
Complex Shapes ◽  
Complex Parts

Electrochemical polishing is a well-known method in finishing of complex shapes with high surface quality. Inner surface polishing of complex parts with high precision can also be easily done by this method. In this research, barrel chamber’s surface, with numerous serial surface angles, is analyzed so that, according to the various set ups, the optimized polishing parameters are obtained. The comparison between electrochemical polishing and conventional methods from this point of view, shows good advantages of this method, so that, the machining time is more than thirty times less and produces very high surface quality. Besides, the dimensional accuracy of the workpiece repeatability process in this polishing method is noticeable.

Sign in / Sign up

Export Citation Format

Share Document