Challenges in Failure Analysis of 3D Bonded Wafers

2018 ◽  
Author(s):  
Pradip Sairam Pichumani ◽  
Tanya Atanasova ◽  
Frieder Baumann ◽  
Michael Hatzistergos ◽  
Jay Mody ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Interfacial Strength ◽  
Auger Spectroscopy ◽  
Acoustic Microscopy ◽  
Force Microscopy ◽  
Analysis Methodology ◽  
Confocal Scanning ◽  
Double Cantilever Beam Test

Abstract This paper discusses the Failure Analysis methodology used to characterize 3D bonded wafers during the different stages of optimization of the bonding process. A combination of different state-of-the-art techniques were employed to characterize the 3D patterned and unpatterned bonded wafers. These include Confocal Scanning Acoustic Microscopy (CSAM) to determine the existence of voids, Atomic Force Microscopy (AFM) to determine the roughness of the films on the wafers, and the Double Cantilever Beam Test to determine the interfacial strength. Focused Ion Beam (FIB) was used to determine the alignment offset in the patterns. The interface was characterized by Auger Spectroscopy and the precession electron nanobeam diffraction analysis to understand the Cu grain boundary formation.

Direct Plan View FIB Liftout for Near-Surface Defect Analysis in TEM

2013 ◽  
Author(s):  
Max L. Lifson ◽  
Carla M. Chapman ◽  
D. Philip Pokrinchak ◽  
Phyllis J. Campbell ◽  
Greg S. Chrisman ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Silicon Germanium ◽  
Focused Ion Beam ◽  
Surface Defects ◽  
Ion Beam ◽  
Misfit Dislocations ◽  
Tem Analysis ◽  
Plan View ◽  
Near Surface ◽  
Straightforward Method

Abstract Plan view TEM imaging is a powerful technique for failure analysis and semiconductor process characterization. Sample preparation for near-surface defects requires additional care, as the surface of the sample needs to be protected to avoid unintentionally induced damage. This paper demonstrates a straightforward method to create plan view samples in a dual beam focused ion beam (FIB) for TEM studies of near-surface defects, such as misfit dislocations in heteroepitaxial growths. Results show that misfit dislocations are easily imaged in bright-field TEM and STEM for silicon-germanium epitaxial growth. Since FIB tools are ubiquitous in semiconductor failure analysis labs today, the plan view method presented provides a quick to implement, fast, consistent, and straightforward method of generating samples for TEM analysis. While this technique has been optimized for near-surface defects, it can be used with any application requiring plan view TEM analysis.

Fast Turn-around Failure Analysis of Metal Interconnection Using FIB and LA ICP-MS

2010 ◽  
Author(s):  
Zixiao Pan ◽  
Wei Wei ◽  
Fuhe Li
Keyword(s):  
Failure Analysis ◽  
Inductively Coupled Plasma ◽  
Structural Damage ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Detection Sensitivity ◽  
Chemical Contamination ◽  
Inductively Coupled ◽  
Minimal Sample ◽  
Icp Ms

Abstract This paper introduces our effort in failure analysis of a 200 nm thick metal interconnection on a glass substrate and covered with a passivation layer. Structural damage in localized areas of the metal interconnections was observed with the aid of focused ion beam (FIB) cross-sectioning. Laser ablation inductively coupled plasma mass spectroscopy (LA ICP-MS) was then applied to the problematic areas on the interconnection for chemical survey. LA ICP-MS showed direct evidence of localized chemical contamination, which has likely led to corrosion (or over-etching) of the metal interconnection and the assembly failure. Due to the high detection sensitivity of LA ICP-MS and its compatibility with insulating material analysis, minimal sample preparation is required. As a result, the combination of FIB and LA ICP-MS enabled successful meso-scale failure analysis with fast turnaround and reasonable cost.

Application of Conductive-AFM in Soft Failure Analysis

2017 ◽  
Author(s):  
Chuan Zhang ◽  
Yinzhe Ma ◽  
Gregory Dabney ◽  
Oh Chong Khiam ◽  
Esther P.Y. Chen
Keyword(s):  
Failure Analysis ◽  
Conductive Atomic Force Microscopy ◽  
Test Parameter ◽  
Conductive Afm ◽  
Force Microscopy ◽  
Analysis Methodology ◽  
Soft Failure ◽  
Atomic Force ◽  
Test Conditions ◽  
Sensitive Characteristics

Abstract Soft failures are among the most challenging yield detractors. They typically show test parameter sensitive characteristics, which would pass under certain test conditions but fail under other conditions. Conductive-atomic force microscopy (CAFM) emerged as an ideal solution for soft failure analysis that can balance the time and thoroughness. By inserting CAFM into the soft failure analysis flow, success rate of such type of analysis can be significantly enhanced. In this paper, a logic chain soft failure and a SRAM local bitline soft failure are used as examples to illustrate how this failure analysis methodology provides a powerful and efficient solution for soft failure analysis.

Logical-to-Physical Device Navigation using Place-and-Route Data as an Alternative to LVS

2006 ◽  
Author(s):  
Roger Nicholson
Keyword(s):  
Failure Analysis ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Traditional Methods ◽  
Navigation Data ◽  
Use Of Time ◽  
Place And Route ◽  
Physical Layout

Abstract Logical-to-physical device navigation for failure analysis is often used to drive physical probers and focused ion beam tools. Traditional methods of creating navigation data rely upon the use of time consuming Layout-versus-Schematic (LVS) based methods. By using existing place-and-route data, full cross-linked navigation between schematic and physical layout may be achieved in a fraction of the time that it takes for the LVS methods to be used. Place-and-route data offers significantly more information to the analyst than LVS based data.

Layout Overlay Techniques to Improve Failure Analysis

1998 ◽  
Author(s):  
Christian Burmer ◽  
Siegfried Görlich ◽  
Siegfried Pauthner
Keyword(s):  
Failure Analysis ◽  
Focused Ion Beam ◽  
New Technologies ◽  
Ion Beam ◽  
Image Correlation ◽  
Microelectronic Devices ◽  
Overlay Technique ◽  
Correlation Techniques ◽  
Navigation Software ◽  
Image Format

Abstract New layout overlay technique has been developed based on standard image correlation techniques to support failure analysis in modern microelectronic devices, which are critical to analyze because they are realized in new technologies using sub-ìm design rules, chemical mechanical polishing techniques (CMP) and autorouted design techniques. As the new technique is realized as an extension of a standard CAD-navigation software and as it makes use of standard image format "TIFF" for data input, which is available at all modern equipments for failure analysis, these technique can be applied to all modern failure analysis methods. Here examples are given for three areas of application: circuit modification using Focused Ion Beam (FIB), support of preparation for backside inspection and fault localization using emission microscopy.

Solving the Voltage Contrast on Floating Substrate with Standard FA Toolset

2016 ◽  
Author(s):  
Julien Goxe ◽  
Béatrice Vanhuffel ◽  
Marie Castignolles ◽  
Thomas Zirilli
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Sample Preparation ◽  
Failure Analysis ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Silicon On Insulator ◽  
Mixed Signal ◽  
Voltage Contrast ◽  
Scanning Electron

Abstract Passive Voltage Contrast (PVC) in a Scanning Electron Microscope (SEM) or a Focused Ion Beam (FIB) is a key Failure Analysis (FA) technique to highlight a leaky gate. The introduction of Silicon On Insulator (SOI) substrate in our recent automotive analog mixed-signal technology highlighted a new challenge: the Bottom Oxide (BOX) layer, by isolating the Silicon Active Area from the bulk made PVC technique less effective in finding leaky MOSFET gates. A solution involving sample preparation performed with standard FA toolset is proposed to enhance PVC on SOI substrate.

High-Throughput, Site-Specific Sample Prep of Ultra-Thin TEM Lamella for Process Metrology and Failure Analysis

2012 ◽  
Author(s):  
Roger Alvis ◽  
Jeff Blackwood ◽  
Sang-Hoon Lee ◽  
Matthew Bray
Keyword(s):  
Sample Preparation ◽  
Failure Analysis ◽  
Process Monitoring ◽  
High Throughput ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Memory Devices ◽  
Site Specific ◽  
Critical Dimensions ◽  
Tem Lamella

Abstract Semiconductor devices with critical dimensions less than 20nm are now being manufactured in volume. A challenge facing the failure analysis and process-monitoring community is two-fold. The first challenge of TEM sample prep of such small devices is that the basic need to end-point on a feature-of-interest pushes the imaging limit of the instrument being used to prepare the lamella. The second challenge posed by advanced devices is to prepare an artifact-free lamella from non-planar devices such as finFETs as well as from structures incorporating ‘non-traditional’ materials. These challenges are presently overcome in many advanced logic and memory devices in the focused ion beam-based TEM sample preparation processes by inverting the specimen prior to thinning to electron transparency. This paper reports a highthroughput method for the routine preparation of artifact-free TEM lamella of 20nm thickness, or less.

Failure Modes, Reliability Analysis and Case Studies on the Integration of Copper and Low-K Technology

2004 ◽  
Author(s):  
Huixian Wu ◽  
James Cargo ◽  
Huixian Wu ◽  
Marvin White
Keyword(s):  
Failure Analysis ◽  
Case Studies ◽  
Cross Section ◽  
Focused Ion Beam ◽  
Failure Modes ◽  
Ion Beam ◽  
Copper Interconnects ◽  
Wet Chemical ◽  
Low K ◽  
Section Analysis

Abstract The integration of copper interconnects and low-K dielectrics will present novel failure modes and reliability issues to failure analysts. This paper discusses failure modes related to Cu/low-K technology. Here, physical failure analysis (FA) techniques including deprocessing and cross-section analysis have been developed. The deprocessing techniques include wet chemical etching, reactive ion etching, chemical mechanical polishing and a combination of these techniques. Case studies on different failure modes related to Cu/low k technology are discussed: copper voiding, copper extrusion; electromigration stress failure; dielectric cracks; delamination-interface adhesion; and FA on circuit-under-pad. For the cross-section analysis of copper/low-K samples, focused ion beam techniques have been developed. Scanning electron microscopy, EDX, and TEM analytical analysis have been used for failure analysis for Cu/low-K technology. Various failure modes and reliability issues have also been addressed.

Localization Techniques on a 0.15um CMOS Device: Charge Pump Failure Analysis

2002 ◽  
Author(s):  
Hui Pan ◽  
Thomas Gibson
Keyword(s):  
Failure Analysis ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Electrical Characterization ◽  
Charge Pump ◽  
Front Side ◽  
Pump Failure ◽  
Electrical Failure ◽  
Optical Proximity Correction ◽  
A Charge

Abstract In recent years, there have been many advances in the equipment and techniques used to isolate faults. There are many options available to the failure analyst. The available techniques fall into the categories of electrical, photonic, thermal and electron/ion beam [1]. Each technique has its advantages and its limitations. In this paper, we introduce a case of successful failure analysis using a combination of several fault localization techniques on a 0.15um CMOS device with seven layers of metal. It includes electrical failure mode characterization, front side photoemission, backside photoemission, Focused Ion Beam (FIB), Scanning Electron Microscope (SEM) and liquid crystal. Electrical characterization along with backside photoemission proved most useful in this case as a poly short problem was found to be causing a charge pump failure. A specific type of layout, often referred to as a hammerhead layout, and the use of Optical Proximity Correction (OPC) contributed to the poly level shorts.

Failure Analysis Strategies for Multistacked Memory Devices with TSV Interconnects

2015 ◽  
Author(s):  
Frank Altmann ◽  
Christian Grosse ◽  
Falk Naumann ◽  
Jens Beyersdorfer ◽  
Tony Veches
Keyword(s):  
Failure Analysis ◽  
Focused Ion Beam ◽  
Failure Modes ◽  
Ion Beam ◽  
Memory Devices ◽  
Metallographic Cross Section ◽  
Electron Beam Induced Current ◽  
Thermal Simulations ◽  
Lock In ◽  
Non Destructive

Abstract In this paper we will demonstrate new approaches for failure analysis of memory devices with multiple stacked dies and TSV interconnects. Therefore, TSV specific failure modes are studied on daisy chain test samples. Two analysis flows for defect localization implementing Electron Beam Induced Current (EBAC) imaging and Lock-in-Thermography (LIT) as well as adapted Focused Ion Beam (FIB) preparation and defect characterization by electron microscopy will be discussed. The most challenging failure mode is an electrical short at the TSV sidewall isolation with sub-micrometer dimensions. It is shown that the leakage path to a certain TSV within the stack can firstly be located by applying LIT to a metallographic cross section and secondly pinpointing by FIB/SEM cross-sectioning. In order to evaluate the potential of non-destructive determination of the lateral defect position, as well as the defect depth from only one LIT measurement, 2D thermal simulations of TSV stacks with artificial leakages are performed calculating the phase shift values per die level.

Sign in / Sign up

Export Citation Format

Share Document