The Mechanical Properties of Combustion-Sprayed Polymers and Blends

1996 ◽  
Author(s):  
J.A. Brogan ◽  
C.C. Berndt ◽  
A. Claudon ◽  
C. Coddet
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Yield Strength ◽  
Deposition Temperature ◽  
Processing Parameters ◽  
Low Energy ◽  
Melt Compounding ◽  
Acid Copolymer ◽  
Spray Processing ◽  
Break Water

Abstract The mechanical properties of EMAA copolymer are dependent upon the thermal spray processing parameters. The parameters determine coating temperatures which, in turn, affects the microstructure. If the deposition temperature is too low, (104 °C for PFl 13 and 160 °C for PFl 11) coatings have low strengths and low energy to break values. Increased coating temperatures allow the particles to fully coalesce resulting in maximized strength and elongation to break. However, at 271 °C, PFl 11 had visible porosity which decreased both strength and elastic modulus. Pigment acts as reinforcement in the sense that the modulus increased but the elongation to break decreased, thus reducing the energy to break. Water quenching reduces the elastic modulus and yield strength, but increases the elongation to break for both EMAA formulations. The mechanical properties of post consumer commingled plastic and PCCP / EMMA blends improved if the recycled plastic was pre-processed by melt-compounding. Melt compounding increased the strength and toughness by improving the compatibility among the various polymer constituents. The addition of PCCP increases the modulus and yield strength of ethylene methaciylic acid copolymer.

Ageing Effect on Mechanical Properties of Machined Nanostructures

2013 ◽  
Vol 683 ◽  
pp. 145-149
Author(s):  
Xing Lei Hu ◽  
Ya Zhou Sun ◽  
Ying Chun Liang ◽  
Jia Xuan Chen
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Yield Strength ◽  
Md Simulation ◽  
Fracture Strain ◽  
Machining Process ◽  
Ageing Process ◽  
Yield Strain ◽  
Before And After ◽  
Mc Simulation

Monte Carlo (MC) method and molecular dynamics (MD) are combined to analyze the influence of ageing on mechanical properties of machined nanostructures. Single crystal copper workpiece is first cut in MD simulation, and then the machined workpiece is used in MC simulation of ageing process, finally the tensile mechanical properties of machined nanostructures before and after ageing are investigated by MD simulation. The results show that machining process and ageing have obvious influence of tensile mechanical properties. After machining, the yield strength, yield strain, fracture strain and elastic modulus reduce by 36.02%, 28.86%, 20.79% and 7.16% respectively. However, the yield strength, yield strain and elastic modulus increase by 4.84%, 1.41% and 1.02% respectively, fracture strain reduce by 24.53% after ageing process. To research the ageing processes of machined nanostructures by MC simulation is both practical and meaningful.

A Study on the Effect of the Temperature on Mechanical Properties of H90 Copper Strip

2019 ◽  
Vol 950 ◽  
pp. 65-69
Author(s):  
Sun Fei ◽  
Xu Cheng
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Yield Strength ◽  
Effect Of Temperature ◽  
Basic Material ◽  
Copper Strip ◽  
Study Results ◽  
Different Temperatures ◽  
Strip Test

In order to study the effect of temperature on the mechanical properties of H90 copper strip material, the H90 copper strip test pieces were heated to different temperatures (20~600 °C) for tensile test; the yield strength, tensile strength, elastic modulus and elongation of H90 copper strip at different temperatures were obtained. Based on the test results, the empirical models of yield strength, tensile strength, elastic modulus of H90 copper strip at high temperature were established; the test showed that, with the increase of temperature, the yield strength, tensile strength and elastic modulus of H90 copper strip decreased greatly, and the elongation after fracture first increased-decreased-increased at 20~600 °C. The study results in this paper provide basic material data for analyzing the effect of temperature on the continuous firing of firearms and other weapons.

Investigation of Pore Structures on Mechanical Properties of Porous Ti by 3D Finite Element Models

2013 ◽  
Vol 647 ◽  
pp. 683-687
Author(s):  
Mi Gong ◽  
Hong Chao Kou ◽  
Yu Song Yang ◽  
Guang Sheng Xu ◽  
Jin Shan Li ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Finite Element ◽  
Elastic Modulus ◽  
Yield Strength ◽  
Finite Element Models ◽  
3D Finite Element ◽  
Pore Model ◽  
Porous Ti ◽  
Pore Structures ◽  
Medium Porosity

The pore structures on mechanical properties of porous Ti were investigated by 3D finite element models. Calculated elastic modulus and yield strength suggested that square-pore models exhibit lower modulus and higher strength compared with another two kinds of shapes (circle and hexagonal). In addition, under the condition of medium porosity (58.96%), integrated property was found in square-pore model which elastic modulus was 26.97GPa, less than 1/3 of hexagonal-pore model; while the yield strength maintained 63.82MPa, doubled the figure of circle-pore model. Thus, models with square-pore structures show potential perspective as hard tissue replacements. Investigation on anisotropy of microstructure implies that the elastic modulus was affected more intensively than the yield strength.

Dependence of Anisotropy of Human Lumbar Vertebral Trabecular Bone on Quantitative Computed Tomography-Based Apparent Density

2014 ◽  
Vol 136 (9) ◽  
Author(s):  
Ameet K. Aiyangar ◽  
Juan Vivanco ◽  
Anthony G. Au ◽  
Paul A. Anderson ◽  
Everett L. Smith ◽  
...  
Keyword(s):  
Computed Tomography ◽  
Mechanical Properties ◽  
Finite Element ◽  
Elastic Modulus ◽  
Yield Strength ◽  
Apparent Density ◽  
Transverse Direction ◽  
Quantitative Computed Tomography ◽  
Axial Direction ◽  
Anisotropy Ratio

Most studies investigating human lumbar vertebral trabecular bone (HVTB) mechanical property–density relationships have presented results for the superior–inferior (SI), or “on-axis” direction. Equivalent, directly measured data from mechanical testing in the transverse (TR) direction are sparse and quantitative computed tomography (QCT) density-dependent variations in the anisotropy ratio of HVTB have not been adequately studied. The current study aimed to investigate the dependence of HVTB mechanical anisotropy ratio on QCT density by quantifying the empirical relationships between QCT-based apparent density of HVTB and its apparent compressive mechanical properties— elastic modulus (Eapp), yield strength (σy), and yield strain (εy)—in the SI and TR directions for future clinical QCT-based continuum finite element modeling of HVTB. A total of 51 cylindrical cores (33 axial and 18 transverse) were extracted from four L1 human lumbar cadaveric vertebrae. Intact vertebrae were scanned in a clinical resolution computed tomography (CT) scanner prior to specimen extraction to obtain QCT density, ρCT. Additionally, physically measured apparent density, computed as ash weight over wet, bulk volume, ρapp, showed significant correlation with ρCT [ρCT = 1.0568 × ρapp, r = 0.86]. Specimens were compression tested at room temperature using the Zetos bone loading and bioreactor system. Apparent elastic modulus (Eapp) and yield strength (σy) were linearly related to the ρCT in the axial direction [ESI = 1493.8 × (ρCT), r = 0.77, p < 0.01; σY,SI = 6.9 × (ρCT) − 0.13, r = 0.76, p < 0.01] while a power-law relation provided the best fit in the transverse direction [ETR = 3349.1 × (ρCT)1.94, r = 0.89, p < 0.01; σY,TR = 18.81 × (ρCT)1.83, r = 0.83, p < 0.01]. No significant correlation was found between εy and ρCT in either direction. Eapp and σy in the axial direction were larger compared to the transverse direction by a factor of 3.2 and 2.3, respectively, on average. Furthermore, the degree of anisotropy decreased with increasing density. Comparatively, εy exhibited only a mild, but statistically significant anisotropy: transverse strains were larger than those in the axial direction by 30%, on average. Ability to map apparent mechanical properties in the transverse direction, in addition to the axial direction, from CT-based densitometric measures allows incorporation of transverse properties in finite element models based on clinical CT data, partially offsetting the inability of continuum models to accurately represent trabecular architectural variations.

scholarly journals Mechanical Properties and Metal-Ceramic Bond Strength of Co-Cr Alloy Manufactured by Selective Laser Melting

Materials ◽  
2020 ◽  
Vol 13 (24) ◽  
pp. 5745
Author(s):  
Joon-Ki Hong ◽  
Seong-Kyun Kim ◽  
Seong-Joo Heo ◽  
Jai-Young Koak
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Flexural Strength ◽  
Yield Strength ◽  
Bond Strength ◽  
Selective Laser Melting ◽  
Laser Melting ◽  
Three Point Bending ◽  
Ceramic Bond ◽  
Metal Ceramic

Cobalt–chromium (Co-Cr) metal is one of the widely used biomaterials in the fabrication of dental prosthesis. The purpose of this study was to investigate whether there are differences in the properties of metals and bond strength with ceramics depending on the manufacturing methods of Co-Cr alloy. Co-Cr alloy specimens were prepared in three different ways: casting, milling, and selective laser melting (SLM). The mechanical properties (elastic modulus, yield strength, and flexural strength) of the alloys were investigated by flexure method in three-point bending mode, and microstructures of the specimens were analyzed. After application of the veneering ceramic through the three-point bending test, bond strength of the Metal-Ceramic was investigated. The cracked surfaces were observed by means of energy dispersive X-ray (EDX) spectroscopy and scanning electron microscopy (SEM) with backscattered electron (BSE) images. In mechanical properties, the elastic modulus was highest for the casting group, and the yield strength and flexural strength were lowest for the milling group. The SLM group showed finer homogeneous crystalline-microstructure, and a layered structure was observed at the fractured surface. After the ceramic bond strength test, all groups showed a mixed failure pattern. The casting group showed the highest bond strengths, whereas there was no significant difference between the other two groups. However, all groups have met the standard of bond strength according to international standards organization (ISO) with the appropriate passing rate. The results of this study indicate that the SLM manufacturing method may have the potential to replace traditional techniques for fabricating dental prosthesis.

Correlation of The Mechanical Properties of Silicon Oxynitride Films to Processing Parameters, Film Stoichiometry, and Hydride Bond Concentration

1995 ◽  
Vol 391 ◽  
Author(s):  
Mansour Moinpour ◽  
Farhad Moghadam ◽  
Byron Williams
Keyword(s):  
Thin Films ◽  
Mechanical Properties ◽  
Elastic Modulus ◽  
Linear Correlation ◽  
Processing Parameters ◽  
Silicon Oxynitride ◽  
Nitrogen Hydride ◽  
Micro Indentation ◽  
Hardness Values ◽  
Measured Hardness

AbstractA selective range of hydrated silicon oxynitride thin films (SixOyNz:H) have been characterized in terms of their stress, hardness, and modulus in order to mechanically qualify them for use as an encapsulation layer for memory devices (e.g., Flash and EPROM memories). These films are analyzed by RBS and HFS for stoichiometry. The films exhibited stress values between 1.86 x 109 to -3.54 x 109 dyne/cm2 and showed a linear correlation with the hydride ratio (N-H/Si-H). An Ultra Micro-Indentation System (UMIS) measured hardness values between 10.5 GPa to 16.2 GPa while the elastic modulus varied between 119.1 to 141.2 GPa. The monatomic increase of modulus with hardness is attributed to increased amounts of nitrogen and nitrogen hydride bonding in the silicon oxynitride samples.

Investigation of the Effect of Heating-Lines on Tensional Mechanical Properties of Sheet Metal after Laser Forming

2011 ◽  
Vol 117-119 ◽  
pp. 1666-1671
Author(s):  
Ai Hui Luo ◽  
Wen Jiao Dan ◽  
Wei Gang Zhang
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Yield Strength ◽  
Sheet Metal ◽  
Heat Affected Zone ◽  
Total Elongation ◽  
Laser Forming ◽  
Strain Hardening Exponent ◽  
Elongation Index ◽  
Hardening Coefficient

In this study，tensional mechanical properties of sheet metal with different heating-lines after laser forming are investigated. The basic mechanical properties of material (such as elastic modulus, yield strength, ultimate strength, TEI (total elongation index) and EIU (elongation index of uniform)) with different spacing between neighbored heating-lines and different heating-lines number are presented. The stress-strain curves are complied with a modified Swift law, where the hardening coefficient and strain hardening exponent of material are controlled by strain. The influence of heating-lines number on tensional mechanical properties of material is greater than that of the spacing between neighbored heating-lines. The results show that all mechanical properties are related to the distribution of microstructure in heat-affected zone after laser forming.

Synthesis and Characterisation of New Superelastic and Low Elastic Modulus Ti-Nb-X Alloys for Biomedical Application

2011 ◽  
Vol 409 ◽  
pp. 170-174
Author(s):  
A. Ramarolahy ◽  
Philippe Castany ◽  
Thierry Gloriant ◽  
Frédéric Prima ◽  
P. Laheurte ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Yield Strength ◽  
Shape Memory ◽  
Biomedical Application ◽  
The Other ◽  
Alloying Element ◽  
Low Elastic Modulus ◽  
Superelastic Behavior ◽  
Good Biocompatibility

Ti-Nb based alloys are well known to their good mechanical properties, shape memory effect, superelasticity, as well as good biocompatibility. The Ti-24Nb (at%) binary alloy presents a shape memory behavior and low elastic modulus. Our study is focused on the improvement of their mechanical properties by adding a third alloying element (oxygen, nitrogen or silicon). Addition of 0.5 at% of N or O modifies drastically the mechanical behavior of Ti-24Nb alloy that exhibits superelastic behavior instead of shape memory one. On the other hand, addition of 0.5 at% of Si increased yield strength of the Ti-24Nb shape memory alloy.

scholarly journals Dislocation Processes and Deformation Behavior in -Oriented FeX-Ni60–X-Al40 Single Crystals

2000 ◽  
Vol 646 ◽  
Author(s):  
P. S. Brenner ◽  
R. Srinivasan ◽  
R. D. Noebe ◽  
T. Lograsso ◽  
M. J. Mills
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Yield Strength ◽  
Strain Hardening ◽  
Single Crystals ◽  
Deformation Behavior ◽  
Room Temperature ◽  
Elevated Temperatures ◽  
Pseudobinary System ◽  
Dislocation Dissociation

ABSTRACTThe mechanical properties and dislocation microstructure of single crystals with a range of compositions within the Fex-Ni60–x-Al40 pseudobinary system have been investigated, with the purpose of bridging the behavior from FeAl to NiAl. Experiments are focused on the compression testing of <001> oriented single crystals with compositions where x = 10, 20, 30, 40, and 50 (in atomic percent). Observations of a<111> dislocation morphologies at room temperature and both a<111> and non-a<111> dislocation activity at elevated temperatures are reported and discussed. Measurements of the yield strength, elastic modulus and strain hardening rates are reported, and the variation of strength with composition is correlated with dislocation dissociation and overall dislocation morphology.

scholarly journals Investigation on the preparation and mechanical properties of porous Cu35Ni15Cr alloy for a molten carbonate fuel cell

2015 ◽  
Vol 33 (4) ◽  
pp. 887-893
Author(s):  
Cong Li ◽  
Jian Chen ◽  
Wei Li ◽  
Yanjie Ren ◽  
Jianjun He
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Yield Strength ◽  
Ball Milling ◽  
Deformation Temperature ◽  
Loading Rate ◽  
Molten Carbonate Fuel Cell ◽  
Molten Carbonate ◽  
Β Phase ◽  
Steady Level

AbstractThe preparation process of porous Cu35Ni15Cr alloy was studied in this paper. The effect of ball milling time and sintering temperature on the porosity of Cu35Ni15Cr alloy was identified. It was found that 18 h ball milling and 950 °C sintering are the most promising parameters for the preparation of porous Cu35Ni15Cr alloy. The products have a ~62 % porosity. The alloy consists of an α phase and β phase. The influence of deformation temperature and loading rate on the mechanical properties of Cu35Ni15Cr alloys was investigated. The results show that with decreasing deformation temperature, the yield strength and elastic modulus of the porous alloy increase. With the increase of loading rate, the yield strength of these alloys shows an increasing trend, but the elastic modulus is on a steady level.

Sign in / Sign up

Export Citation Format

Share Document