scholarly journals Antimicrobial activity and physicochemical performance of a modified endodontic sealer

2020 ◽  
Vol 9 (11) ◽  
pp. e069119401
Author(s):  
Flávia Gonçalves ◽  
Luiza Mello de Paiva Campos ◽  
Luciana Katty Figueiredo Sanches ◽  
Larissa Tavares Sampaio Silva ◽  
Tamiris Martins Ribeiro dos Santos ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Antimicrobial Activity ◽  
Drug Release ◽  
Flexural Strength ◽  
Physicochemical Properties ◽  
Flexural Modulus ◽  
Control Group ◽  
Ah Plus ◽  
Drug Incorporation ◽  
One Way Anova

Introduction: this study aimed to evaluate the antimicrobial and physicochemical properties of a commercial endodontic sealer modified by the addition of montmorillonite (MMT) nanoparticles loaded with two different drugs: chlorhexidine (CHX) or metronidazole (MET). Methods: 5 wt% MMT/CHX or MMT/MET nanoparticles were added to the sealer AH-Plus. The experimental materials were evaluated for drug release, antimicrobial activity, flow, flexural strength, and flexural modulus. Data were subjected to one-way ANOVA, Kruskal-Wallis, and Mann-Whitney tests. Results: The drug incorporation into MMT particles was 9% and 10% for CHX and MET, respectively. At 20 days after manipulation, 16.5% of the drug was released by the sealer with MMT/MET and 0.4% by MMT/CHX. The addition of both nanoparticles decreased the flow of materials, but they were still in compliance with ISO 6876-2012. The conversion, flexural strength, and flexural modulus of MMT/MET (87%, 37±7 MPa, 2.3 GPa) and MMT/CHX (78%, 29±2 MPa, 2.7 GPa) were similar in both groups but lower than in the control group (100%, 54±7 MPa, 4.0±0.7 GPa). Both experimental materials were able to form an inhibition halo for E. faecalis bacteria (CHX: 4.8±1.4 and MET: 4.0±1.6 mm), whereas the control group did not inhibit the microorganism. Conclusion: both formulations proposed as endodontic sealer presented effective antimicrobial activity and acceptable flow. The addition of MMT/CHX and MMT/MET particles decreased the conversion and mechanical properties, but further studies are required to clarify the clinical relevance of these properties.

scholarly journals Investigating the Mechanical Properties of ZrO2-Impregnated PMMA Nanocomposite for Denture-Based Applications

Materials ◽  
2019 ◽  
Vol 12 (8) ◽  
pp. 1344 ◽  
Author(s):  
Saleh Zidan ◽  
Nikolaos Silikas ◽  
Abdulaziz Alhotan ◽  
Julfikar Haider ◽  
Julian Yates
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Impact Strength ◽  
Flexural Strength ◽  
Flexural Modulus ◽  
Surface Hardness ◽  
Bending Test ◽  
Zro2 Nanoparticles ◽  
Control Group ◽  
The Mean

Acrylic resin PMMA (poly-methyl methacrylate) is used in the manufacture of denture bases but its mechanical properties can be deficient in this role. This study investigated the mechanical properties (flexural strength, fracture toughness, impact strength, and hardness) and fracture behavior of a commercial, high impact (HI), heat-cured denture base acrylic resin impregnated with different concentrations of yttria-stabilized zirconia (ZrO2) nanoparticles. Six groups were prepared having different wt% concentrations of ZrO2 nanoparticles: 0% (control), 1.5%, 3%, 5%, 7%, and 10%, respectively. Flexural strength and flexural modulus were measured using a three-point bending test and surface hardness was evaluated using the Vickers hardness test. Fracture toughness and impact strength were evaluated using a single edge bending test and Charpy impact instrument. The fractured surfaces of impact test specimens were also observed using a scanning electron microscope (SEM). Statistical analyses were conducted on the data obtained from the experiments. The mean flexural strength of ZrO2/PMMA nanocomposites (84 ± 6 MPa) at 3 wt% zirconia was significantly greater than that of the control group (72 ± 9 MPa) (p < 0.05). The mean flexural modulus was also significantly improved with different concentrations of zirconia when compared to the control group, with 5 wt% zirconia demonstrating the largest (23%) improvement. The mean fracture toughness increased in the group containing 5 wt% zirconia compared to the control group, but it was not significant. However, the median impact strength for all groups containing zirconia generally decreased when compared to the control group. Vickers hardness (HV) values significantly increased with an increase in ZrO2 content, with the highest values obtained at 10 wt%, at 0 day (22.9 HV0.05) in dry conditions when compared to the values obtained after immersing the specimens for seven days (18.4 HV0.05) and 45 days (16.3 HV0.05) in distilled water. Incorporation of ZrO2 nanoparticles into high impact PMMA resin significantly improved flexural strength, flexural modulus, fracture toughness and surface hardness, with an optimum concentration of 3–5 wt% zirconia. However, the impact strength of the nanocomposites decreased, apart from the 5 wt% zirconia group.

scholarly journals Physicochemical Properties of a Methacrylate-Based Dental Adhesive Incorporated with Epigallocatechin-3-gallate

2014 ◽  
Vol 25 (6) ◽  
pp. 528-531 ◽  
Author(s):  
Jiovanne Rabelo Neri ◽  
Monica Yamauti ◽  
Victor Pinheiro Feitosa ◽  
Amanda Pontes Maia Pires ◽  
Rinaldo dos Santos Araújo ◽  
...  
Keyword(s):  
Flexural Strength ◽  
Physicochemical Properties ◽  
Water Sorption ◽  
Degree Of Conversion ◽  
The Other ◽  
Control Group ◽  
Dental Adhesive ◽  
Three Point Bending ◽  
Significant Difference ◽  
One Way Anova

This study aimed to evaluate the influence of epigallocatechin-3-gallate (EGCG) incorporation on the physicochemical properties of a methacrylate-based dental adhesive. EGCG was added to Adper Easy One (3M-ESPE) except in control group, to obtain concentrations of 0.01% w/w and 0.1% w/w of EGCG-doped adhesives. For water sorption (WS) and solubility (SL) surveys, resin discs were assayed following ISO recommendations (n=10). The degree of conversion (DC) was analyzed by FTIR whereas flexural strength (FS) was tested by three-point bending with bar specimens (n=10). Data were subjected to one-way ANOVA and Tukey's test (p<0.05). No significant difference in the DC, WS and FS were found between the different concentrations of EGCG (p>0.05). Adhesives containing 0.1% or 0.01% of EGCC demonstrated similar values of SL (p>0.05) and higher than those found for adhesive without EGCC (p<0.05). In conclusion, the addition of EGCC to adhesive reduced the solubility without affecting the other evaluated properties.

Contamination of Composite Resin by Glove Powder and Saliva Contaminants: Impact on Mechanical Properties and Incremental Layer Debonding

2015 ◽  
Vol 40 (4) ◽  
pp. 396-402 ◽  
Author(s):  
NM Martins ◽  
GU Schmitt ◽  
HL Oliveira ◽  
MM Madruga ◽  
RR Moraes ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Flexural Strength ◽  
Bond Strength ◽  
Mechanical Performance ◽  
Composite Resin ◽  
Flexural Modulus ◽  
Control Group ◽  
Digital Manipulation ◽  
Diametral Tensile Strength

SUMMARY This study investigated the influence of digital manipulation of a composite resin (Z250; 3M ESPE, St Paul, MN, USA) with gloves contaminated with powder and/or human stimulated saliva on the mechanical properties and incremental layer debonding of the restorative. The six groups tested were powdered gloves with or without saliva, powder-free gloves with or without saliva, powdered gloves with saliva cleaned with 70% ethanol, and no digital manipulation or contamination (control). Diametral tensile strength, flexural strength, flexural modulus, and incremental layer shear bond strength were evaluated. Each composite increment was digitally manipulated for 10 seconds. Data from each test were separately analyzed using analysis of variance and the Student-Newman-Keuls test (α=0.05). No significant differences for diametral tensile strength were observed. Manipulation of the composite using powder-free gloves with saliva or using gloves cleaned with ethanol generated higher flexural strength and modulus compared to the other groups. The control group and the group manipulated using powdered gloves with saliva generally showed lower mechanical performances. Lower incremental layer bond strength was observed for the group manipulated with powdered gloves without saliva. The control group and the groups manipulated with powdered gloves with saliva or cleaned with ethanol showed higher shear bond strengths. Most of the failures were cohesive. In conclusion, digital manipulation might be important for the composite resin to achieve better mechanical performance and incremental layer bond strength, provided that the gloves are not contaminated. Cleaning the gloves with ethanol might avoid the negative effects of digital manipulation using contaminated gloves.

scholarly journals Comparison of Mechanical Properties of PMMA Disks for Digitally Designed Dentures

Polymers ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1745
Author(s):  
Tamaki Hada ◽  
Manabu Kanazawa ◽  
Maiko Iwaki ◽  
Awutsadaporn Katheng ◽  
Shunsuke Minakuchi
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Water Sorption ◽  
Water Solubility ◽  
Flexural Modulus ◽  
Manufacturing Method ◽  
Heat Curing ◽  
Significant Difference ◽  
Cad Cam ◽  
Curing Method

In this study, the physical properties of a custom block manufactured using a self-polymerizing resin (Custom-block), the commercially available CAD/CAM PMMA disk (PMMA-disk), and a heat-polymerizing resin (Conventional PMMA) were evaluated via three different tests. The Custom-block was polymerized by pouring the self-polymerizing resin into a special tray, and Conventional PMMA was polymerized with a heat-curing method, according to the manufacturer’s recommended procedure. The specimens of each group were subjected to three-point bending, water sorption and solubility, and staining tests. The results showed that the materials met the requirements of the ISO standards in all tests, except for the staining tests. The highest flexural strength was exhibited by the PMMA-disk, followed by the Custom-block and the Conventional PMMA, and a significant difference was observed in the flexural strengths of all the materials (p < 0.001). The Custom-block showed a significantly higher flexural modulus and water solubility. The water sorption and discoloration of the Custom-block were significantly higher than those of the PMMA-disk, but not significantly different from those of the Conventional PMMA. In conclusion, the mechanical properties of the three materials differed depending on the manufacturing method, which considerably affected their flexural strength, flexural modulus, water sorption and solubility, and discoloration.

scholarly journals Mechanical Properties and Biocompatibility of Urethane Acrylate-Based 3D-Printed Denture Base Resin

Polymers ◽  
2021 ◽  
Vol 13 (5) ◽  
pp. 822
Author(s):  
Jy-Jiunn Tzeng ◽  
Tzu-Sen Yang ◽  
Wei-Fang Lee ◽  
Hsuan Chen ◽  
Hung-Ming Chang
Keyword(s):  
Mechanical Properties ◽  
3D Printing ◽  
Flexural Modulus ◽  
Measurement Data ◽  
Uv Exposure ◽  
Control Group ◽  
Urethane Acrylate ◽  
Shore Hardness ◽  
Digital Light Processing ◽  
Denture Base

In this study, five urethane acrylates (UAs), namely aliphatic urethane hexa-acrylate (87A), aromatic urethane hexa-acrylate (88A), aliphatic UA (588), aliphatic urethane triacrylate diluted in 15% HDD (594), and high-functional aliphatic UA (5812), were selected to formulate five UA-based photopolymer resins for digital light processing (DLP)-based 3D printing. Each UA (40 wt%) was added and blended homogenously with ethoxylated pentaerythritol tetraacrylate (40 wt%), isobornyl acrylate (12 wt%), diphenyl (2,4,6-trimethylbenzoyl) phosphine oxide (3 wt%), and a pink acrylic (5 wt%). Each UA-based resin specimen was designed using CAD software and fabricated using a DLP 3D printer to specific dimensions. Characteristics, mechanical properties, and cytotoxicity levels of these designed UA-based resins were investigated and compared with a commercial 3D printing denture base acrylic resin (BB base) control group at different UV exposure times. Shore hardness-measurement data and MTT assays were analyzed using a one-way analysis of variance with Bonferroni’s post hoc test, whereas viscosity, maximum strength, and modulus were analyzed using the Kruskal–Wallis test (α = 0.05). UA-based photopolymer resins with tunable mechanical properties were successfully prepared by replacing the UA materials and the UV exposure times. After 15 min of UV exposure, the 5812 and 594 groups exhibited higher viscosities, whereas the 88A and 87A groups exhibited lower viscosities compared with the BB base group. Maximum flexural strength, flexural modulus, and Shore hardness values also revealed significant differences among materials (p < 0.001). Based on MTT assay results, the UA-based photopolymer resins were nontoxic. In the present study, mechanical properties of the designed photopolymer resins could be adjusted by changing the UA or UV exposure time, suggesting that aliphatic urethane acrylate has good potential for use in the design of printable resins for DLP-type 3D printing in dental applications.

Mechanical properties and toughening mechanisms of epoxy/graphene nanocomposites

2015 ◽  
Vol 35 (3) ◽  
pp. 257-266 ◽  
Author(s):  
Rahim Eqra ◽  
Kamal Janghorban ◽  
Habib Daneshmanesh
Keyword(s):  
Mechanical Properties ◽  
Fracture Surface ◽  
Flexural Strength ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Graphene Nanosheets ◽  
Flexural Modulus ◽  
Mechanical Tests ◽  
Toughening Mechanism ◽  
Graphene Nanocomposites

Abstract Because of extraordinary physical, chemical and mechanical properties, graphene nanosheets (GNS) are suitable fillers for optimizing the properties of different polymers. In this research, the effect of GNS content (up to 1 wt.%) on tensile and flexural properties, morphology of fracture surface, and toughening mechanism of epoxy were investigated. Results of mechanical tests showed a peak for tensile and flexural strength of samples with 0.1 wt.% GNS such that the tensile and flexural strength improved by 13% and 3.3%, respectively. The Young’s modulus and flexural modulus increased linearly with GNS content, although the behavior of the Young’s modulus was more remarkable. Morphological investigations confirmed this behavior because the GNS dispersion in the epoxy matrix was uniform at lower contents and agglomerated at higher contents. Finally, microscopical observation showed that the major toughening mechanism of graphene-epoxy nanocomposites was crack path deflection, which changed the mirror fracture surface of the pure epoxy to rough surface.

scholarly journals Influence of Different Concentration and Ratio of a Photoinitiator System on the Properties of Experimental Resin Composites

2017 ◽  
Vol 28 (6) ◽  
pp. 726-730 ◽  
Author(s):  
Caio Vinícius Signorelli Grohmann ◽  
Eveline Freitas Soares ◽  
Eduardo José Carvalho Souza-Junior ◽  
William Cunha Brandt ◽  
Regina Maria Puppin-Rontani ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Flexural Strength ◽  
Tertiary Amine ◽  
Water Sorption ◽  
Water Solubility ◽  
Distilled Water ◽  
Resin Composites ◽  
Amine Concentration ◽  
One Way Anova

Abstract The aim in this study was to evaluate the influence of different ratio of camphorquinone/tertiary amine concentration on the flexural strength (FS), elastic modulus (EM), degree of conversion (DC), yellowing (YL), water sorption (WS) and water solubility (WSL) of experimental composites. Thus, acrylate blends were prepared with different camphorquinone (CQ) and amine (DABE) concentrations and ratios by weight: (CQ/DABE%): 0.4/0.4% (C1), 0.4/0.8% (C2), 0.6/0.6% (C3), 0.6/1.2% (C4), 0.8/0.8% (C5), 0.8/1.6% (C6), 1.0/1.0% (C7), 1.0/2.0% (C8), 1.5/1.5% (C9), 1.5/3.0% (C10). For the FS and EM, rectangular specimens (7x2x1 mm, n=10) were photo-activated by single-peak LED for 20 s and tested at Instron (0.5 mm/min). Then, the same specimens were evaluated by FTIR for DC measurement. For YL, disks (5x2 mm, n=10) were prepared, light-cured for 20 s and evaluated in spectrophotometer using the b aspect of the CIEL*a*b* system. For WS and WSL, the volume of the samples was calculated (mm³). For WS and WSL, composites disks (5x0.5 mm, n=5) were prepared. After desiccation, the specimens were stored in distilled water for 7 days and again desiccated, in order to measure the WS and WSL. Data were submitted to one-way ANOVA and Tukey’s test (5%). The groups C8, C9 and C10 showed higher DC, EM and YL means, compared to other composites. Therefore, the FS and WS values were similar among all groups. Also, C1, C2 and C3 presented higher WSL in 7 days, compared to other composites. In general, higher concentrations of camphorquinone promoted higher physical-mechanical properties; however, inducing higher yellowing effect for the experimental composites

scholarly journals Preliminary Study on Mechanical Properties of 3D Printed Multimaterials ABS/PC Parts: Effect of Printing Parameters

2021 ◽  
Vol 32 (2) ◽  
pp. 87-104
Author(s):  
Pui-Voon Yap ◽  
Ming-Yeng Chan ◽  
Seong-Chun Koay
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Flexural Strength ◽  
Young’S Modulus ◽  
Young's Modulus ◽  
Flexural Modulus ◽  
Nozzle Diameter ◽  
Fused Deposition ◽  
Printing Parameters ◽  
Printing Speed

This research work highlights the mechanical properties of multi-material by fused deposition modelling (FDM). The specimens for tensile and flexural test have been printed using polycarbonate (PC) material at different combinations of printing parameters. The effects of varied printing speed, infill density and nozzle diameter on the mechanical properties of specimens have been investigated. Multi-material specimens were fabricated with acrylonitrile butadiene styrene (ABS) as the base material and PC as the reinforced material at the optimum printing parameter combination. The specimens were then subjected to mechanical testing to observe their tensile strength, Young’s modulus, percentage elongation, flexural strength and flexural modulus. The outcome of replacing half of ABS with PC to create a multi-material part has been examined. As demonstrated by the results, the optimum combination of printing parameters is 60 mm/s printing speed, 15% infill density and 0.8 mm nozzle diameter. The combination of ABS and PC materials as reinforcing material has improved the tensile strength (by 38.46%), Young’s modulus (by 23.40%), flexural strength (by 23.90%) and flexural modulus (by 37.33%) while reducing the ductility by 14.31% as compared to pure ABS. The results have been supported by data and graphs of the analysed specimens.

Effects of Hydrothermal Treatment on the Phase Transformation, Surface Roughness, and Mechanical Properties of Monolithic Translucent Zirconia

2022 ◽  
Author(s):  
CY Zhang ◽  
C Agingu ◽  
H Yang ◽  
H Cheng ◽  
H Yu
Keyword(s):  
Mechanical Properties ◽  
Surface Roughness ◽  
Phase Transformation ◽  
Flexural Strength ◽  
Hydrothermal Treatment ◽  
Cross Sections ◽  
Monoclinic Phase ◽  
Control Group ◽  
Hydrothermal Aging ◽  
Characteristic Strength

SUMMARY Objectives: This study aimed to investigate the effects of hydrothermal treatment on four types of monolithic, translucent, yttria-stabilized, tetragonal zirconia polycrystals (Y-TZPs). Methods and Materials: Two commercially available Y-TZP brands—SuperfectZir High Translucency (Aidite Technology Co, China) and Katana HT (Kuraray Noritake Dental, Japan) were assessed. For each brand of Y-TZP, materials of four coloring types, including noncolored (NC), colored by staining (CS), precolored (PC), and multilayered (ML) specimens were investigated after hydrothermal aging in an autoclave at 134°C/0.2 MPa for 0 (control group), 5, 10, and 20 hours. The tetragonal-to-monoclinic phase transformation, surface roughness, flexural strength, and structural reliability (Weibull analysis) were measured and statistically analyzed (α=0.05). The subsurface microstructure was analyzed with scanning electron microscopy. Results: The group ML exhibited the lowest flexural strength and Weibull characteristic strength among the four coloring types (p&lt;0.05). Slight increases in the monoclinic phase volume, flexural strength, and Weibull characteristic strength were observed after hydrothermal aging (pall&lt;0.05). Regardless of coloring type, no significant effects of aging on the Weibull modulus or surface roughness were found for the tested materials. Compared with the Katana HT cross-sections, the SuperfectZir High Translucency cross-sections exhibited a similar but thicker transformation zone. Conclusions: The coloring procedure and material type were found to affect the mechanical properties and aging resistance of translucent monolithic Y-TZP ceramics. Regardless of the aging time, the surface roughness of the tested Y-TZP ceramics remained unchanged.

Physical Properties of Vanillin Incorporated Self-Curing Orthodontic Polymethylmethacrylate Resin

2020 ◽  
Vol 853 ◽  
pp. 46-50
Author(s):  
Thongchai Poonpiriya ◽  
Pornrachanee Sawaengkit ◽  
Sroisiri Thaweboon ◽  
Pornkiat Churnjitapirom
Keyword(s):  
Flexural Strength ◽  
Physical Properties ◽  
Flexural Modulus ◽  
Orthodontic Appliances ◽  
Surface Porosity ◽  
Significance Level ◽  
Removable Orthodontic Appliances ◽  
Pmma Resin ◽  
One Way Anova

Polymethylmethacrylate (PMMA) resin is the main polymeric material used in removable orthodontic appliances. However, it can promote the adhesion of microbes due to its surface porosity and from long-term use. While vanillin incorporated PMMA resin has been reported to have antimicrobial effects against Candida albicans, the influence of vanillin incorporation on the physical properties of self-curing orthodontic PMMA resin has not been studied. Objective: To determine the flexural strength and flexural modulus of self-curing orthodontic PMMA resin incorporated with vanillin in different concentrations. Materials and methods: Three groups of self-curing orthodontic PMMA with incorporated vanillin concentrations of 0.1%, 0.5% as well as PMMA without vanillin as a control were prepared with ten specimens per group. Flexural strength and flexural modulus were tested by a 3-point bending machine according to ISO 20795-2:2013 specifications. One-way ANOVA and Tukey’s multiple comparison tests at a p<0.05 significance level were used to analyse the data. Results: The 0.1% vanillin incorporated group met ISO standard requirements (flexural strength = 60.48 MPa, flexural modulus = 1756.60 MPa), while the 0.5% vanillin incorporated group failed to pass this standard (flexural strength = 46.94 MPa, flexural modulus = 1423.49 MPa). The means of both flexural strength and flexural modulus showed significant differences among the three groups. Increasing the concentration of vanillin would decrease the flexural strength and flexural modulus of PMMA resin. Conclusion: The incorporation of vanillin into self-curing orthodontic PMMA resin can affect its physical properties, namely flexural strength and flexural modulus. At a concentration of 0.1% vanillin incorporation, PMMA resin displayed physical properties within the ISO standards.

Sign in / Sign up

Export Citation Format

Share Document