scholarly journals PENGARUH DEBIT ALIRAN RESIN BISPHENOL A LP-1Q-EX PADA METODE VACUUM INFUSION RESIN TERHADAP KEKUATAN TARIK KOMPOSIT SERAT KULIT POHON WARU (HIBISCUS TILIACEUS)

2021 ◽  
Vol 4 (01) ◽  
pp. 17-24
Author(s):  
Teddy Wicaksono Wicaksono ◽  
Akhmad Farid ◽  
Nova Risdiyanto Ismail ◽  
Arief Rizki Fadhillah
Keyword(s):  
Tensile Strength ◽  
Bisphenol A ◽  
Tensile Test ◽  
Flow Rate ◽  
Natural Fiber ◽  
Fiber Composites ◽  
Type I ◽  
Resin Flow ◽  
Vacuum Infusion ◽  
Resin Method

Research on natural fiber composites is being carried out in various parts of the world to produce solutions to environmental problems by utilizing natural fiber materials prepared for environmentally friendly and renewable materials. The natural fiber currently being developed for composite reinforcement is hibiscus bark fiber. This study aims to determine the effect of the flow rate of bisphenol A resin LP-1Q-EX on the vacuum infusion resin method on the tensile strength of hibiscus bark fiber composites. The method used in this study is the fiber structure model in the direction of tensile load, composite using hibiscus bark fiber (Hibiscus tiliaceus), composite using bisphenol A resin LP-1Q-EX, composite using mass fraction with a ratio of 60 fibers: 40 resin, Waru tree bark was treated with 6% NaOH alkaline soaking (aquades 938.8 grams, and NaOH 61.2 grams) for 120 minutes, the number of hibiscus tiliaceus bark fibers in one composite material was 22 fibers with a material thickness of 3.2 mm (according to ASTM D638-03 Type 1 standard), the composite was produced using the vacuum infusion resin method with variations in resin flow rate of 1.19 ml/s, 3.66 ml/s, 4.67 ml/s. The testing process in this study is a composite tensile test using the ASTM D638-03 Type I standard. The analysis of the fractures that occur in each specimen uses macro photos, namely the process of taking several photos of the fracture after the specimen is subjected to a tensile test using a digital camera placed on the ground. topped a tripod. The results of the composite tensile test showed that the variation of resin flow rate of 1.19 ml/s had the lowest tensile strength of 282.94 MPa, while the variation of flow discharge of 3.66 ml/s had the highest tensile strength of 301.75 MPa. and the flow variation of 4.67 ml/s has a tensile strength of 284.54 MPa. Based on the results of the tensile test of the hibiscus tiliaceus bark fiber composite using the vacuum infusion resin method, the highest strength was obtained at a variation of the resin flow rate of 3.66 ml/s.

Degradation Behaviour of Nanosilica Enhanced Oil Palm Empty Fruit Bunch Fiber Epoxy Composites

2020 ◽  
Vol 305 ◽  
pp. 28-35
Author(s):  
Anslem Wong Tsu An ◽  
Sujan Debnath ◽  
Vincent Lee Chieng Chen ◽  
Moola Mohan Reddy ◽  
Alokesh Pramanik
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Oil Palm ◽  
Environmental Conditions ◽  
Natural Fiber ◽  
Fiber Composites ◽  
Epoxy Composites ◽  
Empty Fruit Bunch ◽  
Degradation Behaviour ◽  
Brine Solution

In recent years, studies regarding natural fiber reinforced composites have been increased as they are biodegradable with good mechanical performance therefore can help to overcome the environmental issue. As the natural fibers are easy to obtain, many industries have started to make use of natural fiber composites which are light in weight and possess good mechanical properties. However, the natural fiber composites also possess certain limitations most importantly their high moisture absorption ability which makes them incompatible at degradable environment. The fiber constituents of natural fiber composite may have different type of interactions at different environmental conditions. In addition, the involvement of nanoparticles in the composite may be the solution to overcome the deficiencies. In this research, the degradation behaviour of Oil palm empty fruit bunch (OPEFB) fibers reinforced epoxy composites upon exposure to degradable environmental conditions and the effect of adding nanoparticles have been studied. The tensile tests were conducted before and after the exposure to different environmental conditions including plain water, moist soil, brine solution, and cooking oil. Results shows that the addition of 10wt% of OPEFB fiber to the epoxy composites had improved the mechanical tensile strength up to 15.97% and composites exposed to brine solution have the most prominent sign of degradation in mechanical properties in both composites with and without nanosilica. Nevertheless, the composites with nanosilica have shown up to 24.28% improvement in tensile strength after exposure to different environmental conditions. The improvement were attributed due to filling the voids of the composites with nanosilica and good interfacial adhesion between the nanofiller, fiber, and matrix.

Bacterial cellulose-natural fiber composites produced by fibers extracted from banana peel waste

2020 ◽  
pp. 152808372092584
Author(s):  
Muhammad Awais Naeem ◽  
Qasim Siddiqui ◽  
Muhammad Rafique Khan ◽  
Muhammad Mushtaq ◽  
Muhammad Wasim ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Tensile Strength ◽  
Bacterial Cellulose ◽  
Natural Fiber ◽  
Natural Fibers ◽  
Fiber Composites ◽  
Banana Peel ◽  
Gravimetric Analysis ◽  
Natural Fiber Composites ◽  
Banana Fibers

In recent times, there is a growing demand for low-cost raw materials, renewable resources, and eco-friendly end products. Natural fibers are considered as strong candidates to be used as a potential reinforcement for composite manufacturing. In the current study, natural fibers extracted from banana peel were coated with bacterial cellulose through a green biosynthesis approach as well as by a simple slurry dipping method. Thus, natural fibers from banana peel waste were used the first time, to produce bacterial cellulose-natural fiber composites. SEM analysis revealed good interaction between the hybrid fibers and the epoxy matrix. Thermal gravimetric analysis results revealed that the degradation temperature increases because of the addition of bacterial cellulose on fiber surface, which improves the thermal stability. The maximum thermal decomposition temperature (405°C) was noticed for nanocomposites reinforced by banana fibers with bacterial cellulose deposited on their surface. Whereas the lowest weight loss was also found for the same sample group. The highest tensile strength (57.95 MPa) was found for SBC-BP/epoxy, followed by DBC-BP/epoxy (54.73 MPa) and NBP/epoxy (45.32 MPa) composites, respectively. Composites reinforced by both types of hybrid banana fibers shown comparatively higher tensile performance as compared with the neat banana peel fiber-epoxy composites, which can be attributed to the high strength and stiffness associated with the bacterial cellulose. Overall, this study suggests a successful and green route for the fabrication of natural fiber-reinforced composites with improved properties such as tensile strength and thermal stability.

Prediction of Mechanical Properties of Polymer Composites Reinforced with Feather Fibers of ‘Emu’ Bird

2014 ◽  
Vol 592-594 ◽  
pp. 694-699
Author(s):  
Chandra V. Sekhar ◽  
V. Pandurangadu ◽  
T. Subba Rao
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Response Surface Methodology ◽  
Natural Fiber ◽  
Flexural Modulus ◽  
Fiber Composites ◽  
Weight Percentage ◽  
Feather Fibers ◽  
Prediction Of Mechanical Properties ◽  
Feather Fiber

Now a day’s researchers are focusing on natural fiber composites. In the present work composites were prepared with epoxy (Araldite LY-556) resin and ‘emu’ bird feathers as fiber. The composites were prepared by varying the weight percentage (P) of ‘emu’ fiber ranging from 1 to 5 and length (L) of feather fibers from 1 to 5 cm. The various mechanical properties like tensile strength, flexural strength; flexural modulus and impact strength were determined. An attempt is made to model the mechanical properties through response surface methodology (RSM). Analysis of Variance (ANOVA) is used to check the validity of the model. The results reveal that the developed models are suitable for prediction of mechanical properties of Epoxy ‘Emu’ Feather Fiber Composites.

Effects on Tensile and Morphology Properties of Casuarina equisetifolia Reinforced Unsaturated Polyester Composites

2013 ◽  
Vol 748 ◽  
pp. 211-215
Author(s):  
Borhan Nurulaini ◽  
Romli A.Z. ◽  
Mohd Hanafiah Abidin
Keyword(s):  
Tensile Strength ◽  
Tensile Test ◽  
Natural Fiber ◽  
Unsaturated Polyester ◽  
Casuarina Equisetifolia ◽  
Microscopy Technique ◽  
Morphological Studies ◽  
Structural Applications ◽  
Polyester Composites ◽  
Composite Samples

New knowledge in findings potential usage of natural fiber as new material in composite technology has been increased gradually in years and these natural fiber materials are well known as competent material which can become an alternative material to the conventional and synthetic materials for suitable applications. In this research, Casuarina equisetifolia leaf was used as bio-based fiber and unsaturated polyester composite as the matrix due to its natural surface roughness without any chemical treatment. The aim of this study was to investigate the effect of various weight loadings of Casuarina equisetifolia in unsaturated polyester composites on the tensile test and morphological studies. The composite samples were fabricated by using press machine with mould dimension of (15x15x0.3) cm. From the tensile test results, tensile strength of the composite samples decreases with the increment of Casuarina equisetifolia by weight loadings. The surface morphology of the fractures composite samples was then analyzed using the microscopy technique (SEM) and found the evidence of fractured fiber breakage and voids content of the samples. Base on the result obtained, the tensile strength at 30% up to 50% weight loading of Casuarina equisetifolia has the potential to be used in non-structural applications.

Impact of Alkali Treatment Conditions on Kenaf Fiber Polyester Composite Tensile Strength

2014 ◽  
Vol 660 ◽  
pp. 285-289 ◽  
Author(s):  
Mohd Yussni Hashim ◽  
Mohd Nazrul Roslan ◽  
Shahruddin Mahzan ◽  
Mohd Zin ◽  
Saparudin Ariffin
Keyword(s):  
Tensile Strength ◽  
Immersion Time ◽  
Natural Fiber ◽  
Alkali Treatment ◽  
Solution Temperature ◽  
Type I ◽  
Kenaf Fiber ◽  
Treatment Conditions ◽  
Polyester Composite ◽  
The Impact

The increase of environmental issues awareness has accelerated the utilization of renewable resources like plant fiber to be used as reinforced material in polymer composite. However, there are significant problems of compatibility between the fiber and the matrix due to weakness in the interfacial adhesion of the natural fiber with the synthetic matrices. One of the solutions to overcome this problem is using chemical modification like alkali treatment. In this study, the impact of alkali treatment conditions on short randomly oriented kenaf fiber reinforced polyester matrix composite tensile strength was investigated. The experimental design setting was based on 2 level factorial experiments. Two parameters were selected during alkali treatment process which are kenaf fiber immersion duration (at 30 minute and 480 minute) and alkali solution temperature (at 40°C and 80°C). Alkali concentration was fixed at 2% (w/v) and the kenaf polyester volume fraction ratio was 10:90. The composite specimens were tested to determine the tensile properties according to ASTM D638-10 Type I. JOEL scanning electron microscopy (SEM) was used to study the microstructure of the material. The result showed that alkali treatment conditions setting do have the impact on tensile strength of short randomly oriented kenaf polyester composite. The interaction factors between immersion time and temperature was found to have prominent factors to the tensile strength of composite followed by the immersion time factor.

scholarly journals Mechanical Properties of Layered-Carbon Fiber Reinforced with Vacuum Infusion Process

2021 ◽  
Vol 6 (1) ◽  
pp. 33-40
Author(s):  
Ali Saifullah ◽  
Mohammad Jufri ◽  
Dini Kurniawati ◽  
Risky Chandra
Keyword(s):  
Mechanical Properties ◽  
Carbon Fiber ◽  
Tensile Test ◽  
Tensile Tests ◽  
Fiber Composites ◽  
Bending Test ◽  
Carbon Fiber Composites ◽  
Fiber Reinforced ◽  
Vacuum Infusion ◽  
Carbon Fiber Reinforced

Research on material engineering is widely developed in the precursors, composition of the material, and technique to create a composite. The layering and vacuum infusion resin are the developing technology to create the composites with the new characteristics and properties. This experiment is intended to find out the characteristics of layering carbon fiber reinforced by resin and is molded with vacuum infusion technique. The specimens of this experiment is layered-carbon fiber composites determined in three, four, five, six, and seven layers. The precursors of 220 and 240 carbon fibers are the main material of the composites. The tests conducted to the specimens are bending and tensile tests. The both tests are treated to reveal the mechanical properties of the composites. The least layers of 220 and 240 carbon fiber result the highest value of bending test, but the most number of carbon fiber layers show the opposite value. The results are reverse in the tensile test. The highest value of the tensile test is achieved by the most layers of carbon fiber, while the lowest value is in the least layers. This result is almost the same with the strain-stress, but overall the graphic is similarly increase to the most layers. Deduction achieved in this experiment is that the number of layers in the carbon fiber composites is significantly influencing the mechanical properties of the composite.

scholarly journals KAJIAN EKSPERIMENTAL TENSILE PROPERTIES KOMPOSIT POLIESTER BERPENGUAT SERAT KARBON SEARAH HASIL MANUFAKTUR VACUUM INFUSION SEBAGAI MATERIAL STRUKTUR LSU

2018 ◽  
Vol 14 (1) ◽  
pp. 61
Author(s):  
Kosim Abdurohman ◽  
Aryandi Marta
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Tensile Test ◽  
Failure Mode ◽  
Modulus Of Elasticity ◽  
Failure Modes ◽  
Volume Fraction ◽  
Manufacturing Method ◽  
Vacuum Infusion

Vacuum infusion is a manufacturing method to improve mechanical properties of composite. Before apply this in LSU structure, it should be experimented using tensile test to know mechanical properties of the composite. Tensile test is an experimental to know tensile strength, modulus of elasticity, and failure modes of composite. Experimental process of CFRP composite using unidirectional carbon fiber and polyester matrix was done using vacuum infusion technology, strart from specimens preparation until testing steps. Manufacturing results gave the values of composite density and thickness; mass and volume fraction of fiber and matrix materials. Specimens and testing process are refer to ASTM D3039 tensile test standard for composite matrix polymers. The testing results showed 1011.67 MPa ultimate tensile strength, 59074.96 MPa modulus of elasticity, and SGV (long spliting, gage, various) failure mode . ABSTRAKVacuum infusion merupakan salah satu metode manufaktur yang digunakan untuk meningkatkan sifat mekanik komposit. Untuk mengaplikasikan metode ini dalam pembuatan struktur LAPAN Surveillance UAV (LSU), perlu diketahui terlebih dahulu sifat mekanik dari komposit hasil metode ini secara eksperimen. Salah satu eksperimen yang dilakukan yaitu pengujian tarik untuk mendapatkan tensile strength, modulus elastisitas, dan failure mode yang terjadi pada komposit. Eksperimen dilakukan terhadap komposit CFRP menggunakan material serat karbon searah (UD) 0⁰ dan matriks poliester dibuat dengan metode vacuum infusion mulai dari tahap preparasi sampai tahap pengujian. Dari hasil manufaktur didapat nilai densitas dan ketebalan komposit serta fraksi massa dan fraksi volume material penyusun komposit. Spesimen dan proses pengujian mengikuti standar ASTM D3039 yang merupakan standar pengujian tarik untuk komposit dengan matriks polimer. Hasil pengujian menunjukkan nilai ultimate tensile strength 1011,67 MPa, modulus elastisitas 59074,96 MPa, dan failure mode SGV (Long Spliting, Gage, Various).

scholarly journals Mechanical Behaviour of Areca Nut, Sunn Hemp Natural Fibers and E-Glass Fibers Reinforced With Epoxy Composites

2019 ◽  
Vol 8 (6) ◽  
pp. 1092-1101 ◽  
Keyword(s):  
Tensile Strength ◽  
Glass Fiber ◽  
Automobile Industry ◽  
Natural Fiber ◽  
Glass Fibers ◽  
Natural Fibers ◽  
Fiber Composites ◽  
Tensile Behaviour ◽  
Areca Nut ◽  
Sunn Hemp

In this paper, tensile behaviour of the natural fiber composites such as the areca nut composites and the sunn hemp composites were determined. The fibers were arranged in different orientations such as the uniaxial, biaxial and the criss-cross arrangements. For both the types of fiber composites, specimens were made with and without the incorporation of E-glass fibers. Comparisons were done on the basis of fiber orientation, E-glass fibers incorporation and the type of natural fiber used. Initially, the fibers were treated with alkali, i.e. Sodium hydroxide (NaOH) in order to get better bonding at the fiber-matrix interface. The conventional hand lay-up technique followed by the soft compression molding technique was carried out for fabricating the composite specimens. It was inferred from the results that the tensile strength was more for uniaxial arrangement and the least for biaxial arrangement in case of both the fibers. Further, for both the fibers, E-glass fiber incorporation increased the tensile strength as compared to the non-incorporated E-glass fiber composites. Also, sunn hemp composites showed better tensile strength than areca nut composites. The research suggested that the areca nut and sunn hemp composites were assets to many potential applications that did not require very high load bearing capabilities. These examined composites can be considered as very reliable materials for fabrication of lightweight materials used in automobile industry, packaging materials, medical field, etc.

Tensile Strength of Banana – Bamboo – Glass Fiber Reinforced Natural Fiber Composites

2014 ◽  
Vol 592-594 ◽  
pp. 1195-1199
Author(s):  
Ashwin Sailesh ◽  
C. Shanjeevi ◽  
J.Jeswin Arputhabalan
Keyword(s):  
Tensile Strength ◽  
Glass Fiber ◽  
Fiber Orientation ◽  
Natural Fiber ◽  
Fiber Composite ◽  
Natural Fibers ◽  
Fiber Composites ◽  
Natural Fiber Composites ◽  
Fiber Reinforced ◽  
Glass Fiber Reinforced

The developments in the field of composite materials are growing tremendously day by day. One such development is the use of natural fibers as reinforcement in the composite material. This is attributed to the fact that natural fibers are environmental friendly, economical, easily available and non-abrasive. Mixing of natural fiber with Glass Fibers is finding increased applications. In this present investigation Banana – Bamboo – Glass fiber reinforced natural fiber composites is fabricated by Hand – Layup technique with varying fiber orientation such as [0°G, 90°BM, 0°BN, 0°G], [0°G, 0°BM, +45°BN, 0°G] and [0°G, 0°BM, 90°BN, 0°G] and are tested for its tensile strength. The tensile strength of the fabricated composites is evaluated. The results indicated that the natural fiber composite with the fiber orientation of [0°G, 0°BM, 90°BN, 0°G] can withstand more load when compared to the samples with other fiber orientation. Nomenclature Used: BN – Banana fiber BM – Bamboo fiber G – Glass fiber

Sign in / Sign up

Export Citation Format

Share Document