Nanoporous Carbon Magnetic Hybrid Derived From Waterlock Polymers and Its Application for Hexavalent Chromium Removal from Aqueous Solution

2021 ◽  
Vol 7 (4) ◽  
pp. 69
Author(s):  
Georgios Asimakopoulos ◽  
Angeliki Karakassides ◽  
Maria Baikousi ◽  
Christina Gioti ◽  
Dimitrios Moschovas ◽  
...  
Keyword(s):  
Hybrid Material ◽  
Chemical Activation ◽  
Iron Carbide ◽  
Nanoporous Carbon ◽  
High Specific Surface Area ◽  
Nanoporous Structure ◽  
Order Kinetic ◽  
Sodium Polyacrylate ◽  
Activation Conditions ◽  
Zero Valent Iron Nanoparticles

Sodium polyacrylate is the superabsorbent waterlock polymer used in disposable diapers, which are the third largest single consumer item in landfills. As diapers are difficult to recycle, their use produces an incredible amount of environmental waste. In the present article, we present a reliable and facile approach to transform sodium polyacrylate, the main constitute in the used diapers, in a carbon-based magnetic sorbent material, capable for use in environmental applications. A nanoporous carbon magnetic hybrid material was prepared by reacting NaPA with iron acetate species under chemical activation conditions. Analysis of the characterization results revealed, the creation of a nanoporous structure, with high specific surface area value (SgBET = 611 m2/g), along with the formation of nanosized zero valent iron nanoparticles and iron carbide (Fe3C), inside the carbon pore system. 57Fe Mössbauer spectroscopy verified also the existence of these two main iron-bearing phases, as well as additional minor magnetic phases, such as Fe3O4 and γ-Fe2O3. Vibrating sample magnetometry (VSM) measurements of the obtained hybrid confirmed its ferromagnetic/ferrimagnetic behavior. The hybrid material demonstrated a rapid sorption of Cr(VI) ions (adsorption capacity: 90 mg/g, 24 h pH = 3). The results showed highly pH-dependent sorption efficiency of the hybrids, whereas a pseudo-second-order kinetic model described their kinetics.

scholarly journals Zero-Valent Iron Nanoparticles for Soil and Groundwater Remediation

2020 ◽  
Vol 17 (16) ◽  
pp. 5817
Author(s):  
Alazne Galdames ◽  
Leire Ruiz-Rubio ◽  
Maider Orueta ◽  
Miguel Sánchez-Arzalluz ◽  
José Luis Vilas-Vilela
Keyword(s):  
Contaminated Soils ◽  
Groundwater Remediation ◽  
Iron Nanoparticles ◽  
Environmental Issues ◽  
High Specific Surface Area ◽  
Zero Valent Iron ◽  
Pilot Studies ◽  
High Effectiveness ◽  
Nanosized Materials ◽  
Zero Valent Iron Nanoparticles

Zero-valent iron has been reported as a successful remediation agent for environmental issues, being extensively used in soil and groundwater remediation. The use of zero-valent nanoparticles have been arisen as a highly effective method due to the high specific surface area of zero-valent nanoparticles. Then, the development of nanosized materials in general, and the improvement of the properties of the nano-iron in particular, has facilitated their application in remediation technologies. As the result, highly efficient and versatile nanomaterials have been obtained. Among the possible nanoparticle systems, the reactivity and availability of zero-valent iron nanoparticles (NZVI) have achieved very interesting and promising results make them particularly attractive for the remediation of subsurface contaminants. In fact, a large number of laboratory and pilot studies have reported the high effectiveness of these NZVI-based technologies for the remediation of groundwater and contaminated soils. Although the results are often based on a limited contaminant target, there is a large gap between the amount of contaminants tested with NZVI at the laboratory level and those remediated at the pilot and field level. In this review, the main zero-valent iron nanoparticles and their remediation capacity are summarized, in addition to the pilot and land scale studies reported until date for each kind of nanomaterials.

scholarly journals Chemical Modification of Combusted Coal Gangue for U(VI) Adsorption: Towards a Waste Control by Waste Strategy

2021 ◽  
Vol 13 (15) ◽  
pp. 8421
Author(s):  
Yuan Gao ◽  
Jiandong Huang ◽  
Meng Li ◽  
Zhongran Dai ◽  
Rongli Jiang ◽  
...  
Keyword(s):  
Structural Analysis ◽  
High Efficiency ◽  
Low Cost ◽  
Chemical Activation ◽  
Cost Effective ◽  
Coal Gangue ◽  
Order Kinetic ◽  
Practical Applications ◽  
Detailed Structural Analysis ◽  
Alkaline Conditions

Uranium mining waste causes serious radiation-related health and environmental problems. This has encouraged efforts toward U(VI) removal with low cost and high efficiency. Typical uranium adsorbents, such as polymers, geopolymers, zeolites, and MOFs, and their associated high costs limit their practical applications. In this regard, this work found that the natural combusted coal gangue (CCG) could be a potential precursor of cheap sorbents to eliminate U(VI). The removal efficiency was modulated by chemical activation under acid and alkaline conditions, obtaining HCG (CCG activated with HCl) and KCG (CCG activated with KOH), respectively. The detailed structural analysis uncovered that those natural mineral substances, including quartz and kaolinite, were the main components in CCG and HCG. One of the key findings was that kalsilite formed in KCG under a mild synthetic condition can conspicuous enhance the affinity towards U(VI). The best equilibrium adsorption capacity with KCG was observed to be 140 mg/g under pH 6 within 120 min, following a pseudo-second-order kinetic model. To understand the improved adsorption performance, an adsorption mechanism was proposed by evaluating the pH of uranyl solutions, adsorbent dosage, as well as contact time. Combining with the structural analysis, this revealed that the uranyl adsorption process was mainly governed by chemisorption. This study gave rise to a utilization approach for CCG to obtain cost-effective adsorbents and paved a novel way towards eliminating uranium by a waste control by waste strategy.

Comparative Study of Different Activation Treatments for the Preparation of Activated Carbon: A Mini-Review

2017 ◽  
Vol 100 (3) ◽  
pp. 299-312 ◽  
Author(s):  
Muhammad Imran Din ◽  
Sania Ashraf ◽  
Azeem Intisar
Keyword(s):  
Activated Carbon ◽  
Comparative Study ◽  
Raw Materials ◽  
Chemical Activation ◽  
Comparative Approach ◽  
Adsorption Mechanisms ◽  
Temperature Activation ◽  
Activation Conditions ◽  
Physical And Chemical ◽  
Characterisation Techniques

In this review, various methods of preparation of activated carbon from agricultural and commercial waste material are reviewed. In addition, we also discuss various activation treatments using a comparative approach. The data are organised in tabulated form for ease of comparative study. A review of numerous characterisation techniques is also provided. The effect of time and temperature, activation conditions, carbonisation conditions and impregnation ratios are explained and several physical and chemical activation treatments of raw materials and their impact on the micro- and mesoporous volumes and surface area are discussed. Lastly, a review of adsorption mechanisms of activated carbon (AC) is also provided.

scholarly journals Highly microporous carbons from olive tree pruning: Optimization of chemical activation conditions

2019 ◽  
Vol 7 (1) ◽  
pp. 102830 ◽  
Author(s):  
Arminda Mamaní ◽  
María Fabiana Sardella ◽  
Marianela Giménez ◽  
Cristina Deiana
Keyword(s):  
Chemical Activation ◽  
Olive Tree ◽  
Microporous Carbons ◽  
Activation Conditions ◽  
Tree Pruning

scholarly journals Effective Removal of Malachite Green from Aqueous Solutions Using Magnetic Nanocomposite: Synthesis, Characterization, and Equilibrium Study

2021 ◽  
Vol 2021 ◽  
pp. 1-15
Author(s):  
Ali Q. Alorabi
Keyword(s):  
Surface Area ◽  
Malachite Green ◽  
Chemical Activation ◽  
Aqueous Media ◽  
Kinetic Studies ◽  
Cost Effective ◽  
Magnetic Nanocomposite ◽  
Bet Surface Area ◽  
Isotherm Models ◽  
Order Kinetic

In this work, magnetized activated Juniperus procera leaves (Fe3O4@AJPL) were successfully prepared via chemical activation of JPL and in situ coprecipitation with Fe3O4. A Fe3O4@AJPL nanocomposite was successfully applied for the elimination of malachite green (MG) dye from aqueous media. The prepared Fe3O4@AJPL adsorbent was characterized by SEM, EDX, TEM, XRD, FTIR, TGA, and BET surface area analyses. The BET surface area and pore size of the Fe3O4@AJPL nanocomposite were found to be 38.44 m2/g and 10.6 nm, respectively. The XRD and FTIR results indicated the formation of a Fe3O4@AJPL nanocomposite. Different parameters, such as pH of the solution (3–8), adsorbent dosage (10–100 mg), temperature (25–45°C), contact time (5-240 min), and initial MG concentrations (20–350 mg/L), for the elimination of the MG dye using Fe3O4@AJPL were optimized and found to be 7, 50 mg, 45°C, 120 min, and 150 mg/L, respectively. The nonlinear isotherm and kinetic studies exhibited a better fitting to second-order kinetic and Langmuir isotherm models, with a maximum monolayer adsorption capacity of 318.3 mg/g at 45°C, which was highly superior to the previously reported magnetic nanocomposite adsorbents. EDX analyses confirmed the presence of nitrogen on the Fe3O4@AJPL surface after MG adsorption. The calculated thermodynamic factors indicated endothermic and spontaneous processes. The desorption of MG dye from Fe3O4@AJPL was performed using a solution of 90% ethanol. Finally, it could be concluded that the designed Fe3O4@AJPL magnetic nanocomposite will be a cost-effective and promising adsorbent for the elimination of MG from aqueous media.

scholarly journals Microporosity Development of Herringbone Carbon Nanofibers by RbOH Chemical Activation

2009 ◽  
Vol 2009 ◽  
pp. 1-5 ◽  
Author(s):  
Vicente Jiménez ◽  
Paula Sánchez ◽  
Fernando Dorado ◽  
José Luís Valverde ◽  
Amaya Romero
Keyword(s):  
Specific Surface ◽  
Surface Area ◽  
Carbon Nanofibers ◽  
Flow Rate ◽  
Chemical Activation ◽  
Micropore Volume ◽  
Structure Development ◽  
Activation Temperature ◽  
Activating Agent ◽  
Activation Conditions

The influence of different activation conditions, including activating agent/CNFs ratio, activation temperature, and He flow rate, on the pore structure development of herringbone carbon nanofibers (CNFs) was studied. The best results of activated CNFs with larger specific surface area can be achieved using the following optimized factors: RbOH/CNFs ratio = 4/1, activation temperature = ,and a He flow rate = 850 ml/min. The optimization of these three factors leads to high CNFs micropore volume, being the surface area increased by a factor of 3 compared to the raw CNFs. It is important to note that only the creation of micropores (ultramicropores principally) took place, and mesopores were not generated if compared with raw CNFs.

scholarly journals Adsorption of hexavalent chromium by activated carbon obtained from a waste lignocellulosic material (Ziziphus jujuba cores): Kinetic, equilibrium, and thermodynamic study

2018 ◽  
Vol 36 (3-4) ◽  
pp. 1066-1099 ◽  
Author(s):  
Radia Labied ◽  
Oumessaad Benturki ◽  
Adh’ Ya Eddine Hamitouche ◽  
André Donnot
Keyword(s):  
Fourier Transform ◽  
Activated Carbon ◽  
Hexavalent Chromium ◽  
Chemical Activation ◽  
Fourier Transform Infrared ◽  
Infrared Analysis ◽  
Order Kinetic ◽  
Lignocellulosic Material ◽  
Ziziphus Jujuba ◽  
Key Functional Groups

In aqueous solutions, hexavalent chromium Cr(VI) was successfully removed by activated carbon “ Z. jujuba rubidium carbonate-activated carbon” obtained from waste lignocellulosic material ( Ziziphus jujuba cores). Rubidium carbonate was used to prepare Z. jujuba rubidium carbonate-activated carbon by chemical activation using a 1:1 w/w ratio. Our results indicate that the obtained surface area of the activated carbon was equal to 608.31 m2/g. The adsorption study of Cr(VI) was investigated under batch conditions at constant stirring speed (220 r/min). Factors such as pH (1–6), temperature (20–40°C), adsorbent concentration (0.5–3 g/l), and initial Cr(VI) concentration (50–500 mg/l) were all studied to attain the maximum removal efficiency. Prior to the adsorption process, the morphology, elementary composition, and loss mass of activated carbon were characterized using scanning electron microscopy, X-ray fluorescence spectrometry, Fourier transform infrared spectroscopy, and thermogravimetric analysis. Fourier transform infrared analysis of the adsorbent demonstrated the presence of key functional groups associated with the adsorption phenomenon such as those of hydroxyl and aromatic groups. The obtained results showed that the optimal conditions for a maximum adsorption efficiency are 2 for pH, 1 g/l for activated carbon dosage and 100 mg/l for Cr(VI) concentration. The removal percentage increased from 27.2 to 62.08%. The kinetic sorption was described by a pseudo-second-order kinetic equation ( R2 ≈ 0.995). The Tóth ( R2 = 0.997) and Elovich models were best to explain the sorption phenomenon. Thermodynamic studies showed that the adsorption of Cr(VI) onto activated carbon was feasible, spontaneous, and endothermic at 20–40°C. This novel Z. jujuba rubidium carbonate-activated carbon derived from Z. jujuba core has been found to be effective for the removal of Cr(VI) and not harmful to the ecosystem.

Analysis of the Factors Affecting the Instrumentation of the Technological Process of the Activated Carbon Material Production

2022 ◽  
pp. 20-30
Author(s):  
A.A. Popova ◽  
I.N. Shubin
Keyword(s):  
Activated Carbon ◽  
Specific Surface ◽  
Carbon Material ◽  
Mutual Influence ◽  
Chemical Activation ◽  
High Specific Surface Area ◽  
Laboratory Research ◽  
High Porosity ◽  
Gas Purification ◽  
Factors Affecting

The article discusses significance of the development of activated carbon materials with a high specific surface area and high porosity. The features of the course of chemical activation and the factors influencing the characteristics of the obtained material have been established. The main stages of the activation of the carbon material, including the preliminary raw carbon material carbonization, its alkaline activation, and the post-processing of the created material, have been determined. The mutual influence of temperature and flow rate of an inert gas on the characteristics of a carbon material obtained with a BET specific surface in the range of 2550–2700 m2/g is experimentally investigated. The analysis of the obtained results has been carried out. Recommendations are given for reducing ambiguity and uncertainty during the transition from laboratory research to pilot production. The resulting activated carbon material can be used as a sorbent in gas purification systems, gas accumulators and for solving various environmental problems.

scholarly journals Adsorption Property, Kinetic and Equilibrium Studies of Activated Carbon Fiber Prepared from Liquefied Wood by Zncl2 Activation

Materials ◽  
2019 ◽  
Vol 12 (9) ◽  
pp. 1377 ◽  
Author(s):  
Ruoke Ma ◽  
Xianxian Qin ◽  
Zhigao Liu ◽  
Yunlin Fu
Keyword(s):  
Activated Carbon ◽  
Carbon Fiber ◽  
Adsorption Property ◽  
Chemical Activation ◽  
Activated Carbon Fiber ◽  
Activation Process ◽  
Order Kinetic ◽  
Liquefied Wood ◽  
Zncl2 Activation ◽  
Mb Adsorption

Activated carbon fiber was prepared from liquefied wood by chemical activation with ZnCl2 (Z-LWACF) at different impregnation ratios, with a particular focus on its adsorption property, kinetic and isotherm. The characterization and properties of Z-LWACFs were investigated by nitrogen adsorption/desorption, X-ray photoelectron spectroscopy (XPS), methylene blue (MB) and iodine adsorption. Two activation process methods were employed to prepare Z-LWACF and contrasted with others fibers. The results showed that the Z-LWACF obtained by one-step ZnCl2 activation present higher yields and specific surface area than others fibers. Besides, the change of MB adsorption value at different impregnation ratios was consistent with pore structure distribution above 1.5 nm pore size, indicating that larger micropores (1.5 to 2 nm) and mesopores played a major role in the MB adsorption by Z-LWACF. The kinetics of MB adsorption process was found to follow the pseudo-second-order kinetic model and the adsorption rate was controlled by chemisorption. It was also found that MB adsroption by Z-LWACF belonged to monolayer adsorption and Z-LWACF was easy to adsorb MB.

scholarly journals Characterization and Modelling Studies of Activated Carbon Produced from Rubber-Seed Shell Using KOH for CO2 Adsorption

Processes ◽  
2019 ◽  
Vol 7 (11) ◽  
pp. 855 ◽  
Author(s):  
Azry Borhan ◽  
Suzana Yusup ◽  
Jun Wei Lim ◽  
Pau Loke Show
Keyword(s):  
Experimental Data ◽  
Activated Carbon ◽  
Co2 Adsorption ◽  
Chemical Activation ◽  
Freundlich Isotherm ◽  
Nitrogen Adsorption ◽  
Rubber Seed ◽  
Modelling Studies ◽  
Carbon Dioxide Co2 ◽  
Activation Conditions

Global warming due to the emission of carbon dioxide (CO2) has become a serious problem in recent times. Although diverse methods have been offered, adsorption using activated carbon (AC) from agriculture waste is regarded to be the most applicable one due to numerous advantages. In this paper, the preparation of AC from rubber-seed shell (RSS), an agriculture residue through chemical activation using potassium hydroxide (KOH), was investigated. The prepared AC was characterized by nitrogen adsorption–desorption isotherms measured in Micrometrices ASAP 2020 and FESEM. The optimal activation conditions were found at an impregnation ratio of 1:2 and carbonized at a temperature of 700 °C for 120 min. Sample A6 is found to yield the largest surface area of 1129.68 m2/g with a mesoporous pore diameter of 3.46 nm, respectively. Using the static volumetric technique evaluated at 25 °C and 1.25 bar, the maximum CO2 adsorption capacity is 43.509 cm3/g. The experimental data were analyzed using several isotherm and kinetic models. Owing to the closeness of regression coefficient (R2) to unity, the Freundlich isotherm and pseudo-second kinetic model provide the best fit to the experimental data suggesting that the RSS AC prepared is an attractive source for CO2 adsorption applications.

Sign in / Sign up

Export Citation Format

Share Document