scholarly journals A Low-Voltage, Ultra-Low-Power, High-Gain Operational Amplifier Design for Portable Wearable Devices

Electronics ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 74
Author(s):  
Na Bai ◽  
Xiaolong Li ◽  
Yaohua Xu
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
Operational Amplifier ◽  
Low Voltage ◽  
Simulation Analysis ◽  
Supply Voltage ◽  
High Gain ◽  
Common Mode ◽  
Ultra Low Power ◽  
The Common

Based on the SMIC 0.13 um CMOS technology, this paper uses a 0.8 V supply voltage to design a low-voltage, ultra-low-power, high-gain, two-stage, fully differential operational amplifier. Through the simulation analysis, when the supply voltage is 0.8 V, the design circuit meets the ultra-low power consumption and also has the characteristic of high gain. The five-tube, fully differential, and common-source amplifier circuits provide the operational amplifier with high gain and large swing. Unlike the traditional common-mode feedback, this paper uses the output of the common-mode feedback as the bias voltage of the five-tube operational transconductance amplifier load, which reduces the design cost of the circuit; the structure involves self-cascoding composite MOS, which makes the common-mode feedback loop more sensitive. The frequency compensation circuit adopts Miller compensation technology with zero-pole separation, which increases the stability of the circuit. The input of the circuit uses the current mirror. A small reference current is chosen to reduce power consumption. A detailed performance simulation analysis of this operational amplifier circuit is carried out on the Cadence spectre platform. The open-loop gain of this operational amplifier is 74.1 dB, the phase margin is 61°, the output swing is 0.7 V, the common-mode rejection ratio is 109 dB, and the static power consumption is only 11.2 uW.

A ± 0.2 V, 0.12 μW CCTA USING VTMOS AND AN APPLICATION FRACTIONAL-ORDER UNIVERSAL FILTER

2014 ◽  
Vol 23 (09) ◽  
pp. 1450126 ◽  
Author(s):  
TADA COMEDANG ◽  
PATTNA INTANI
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
Fractional Order ◽  
Low Voltage ◽  
Supply Voltage ◽  
Current Mode ◽  
Oxide Semiconductor ◽  
Ultra Low Power ◽  
Variable Threshold ◽  
High Output Impedance

In this paper, a variable threshold voltage metal oxide semiconductor (VTMOS) field effect transistor is used to improve an ultra-low voltage, ultra-low power current conveyor transconductance amplifier (CCTA). To achieve the desired result, an analytical subthreshold VTMOS model is used. Designs that utilize the TSMC 0.18 μm technology are verified using PSPICE simulation. The power consumption is simply 0.12 μW at a ± 0.2 V supply voltage. The proposed CCTA is synthesized using fractional-order (FO) universal filters that can simultaneously realise low pass (LP), high pass (HP) and bandpass (BP) responses with independent control of quality factor and pole frequency by transconductances (gm). Moreover, the circuit has low input and high output impedance which would be an ideal choice for cascading in current-mode circuit. The FO filters are constructed using two FO capacitors of orders α and β (0 < α, β ≤ 1). The FO filters provide improved performance in terms of pole frequency compared with conventional-order filters. The filter has a low power consumption of 0.71 μW at a ± 0.2 V supply voltage. The validity of the proposed filter is verified through PSPICE simulations.

COMPOSITE TRANSISTOR CELL USING DYNAMIC BODY BIAS FOR HIGH GAIN AND LOW-VOLTAGE APPLICATIONS

2014 ◽  
Vol 23 (08) ◽  
pp. 1450108 ◽  
Author(s):  
VANDANA NIRANJAN ◽  
ASHWANI KUMAR ◽  
SHAIL BALA JAIN
Keyword(s):  
Low Power ◽  
Large Scale ◽  
Low Voltage ◽  
Supply Voltage ◽  
High Gain ◽  
Signal Frequency ◽  
Output Impedance ◽  
Self Cascode ◽  
Intrinsic Gain ◽  
Body Bias

In this work, a new composite transistor cell using dynamic body bias technique is proposed. This cell is based on self cascode topology. The key attractive feature of the proposed cell is that body effect is utilized to realize asymmetric threshold voltage self cascode structure. The proposed cell has nearly four times higher output impedance than its conventional version. Dynamic body bias technique increases the intrinsic gain of the proposed cell by 11.17 dB. Analytical formulation for output impedance and intrinsic gain parameters of the proposed cell has been derived using small signal analysis. The proposed cell can operate at low power supply voltage of 1 V and consumes merely 43.1 nW. PSpice simulation results using 180 nm CMOS technology from Taiwan Semiconductor Manufacturing Company (TSMC) are included to prove the unique results. The proposed cell could constitute an efficient analog Very Large Scale Integration (VLSI) cell library in the design of high gain analog integrated circuits and is particularly interesting for biomedical and instrumentation applications requiring low-voltage low-power operation capability where the processing signal frequency is very low.

scholarly journals A 0.3 V Rail-to-Rail Ultra-Low-Power OTA with Improved Bandwidth and Slew Rate

2021 ◽  
Vol 11 (2) ◽  
pp. 19
Author(s):  
Francesco Centurelli ◽  
Riccardo Della Sala ◽  
Pietro Monsurrò ◽  
Giuseppe Scotti ◽  
Alessandro Trifiletti
Keyword(s):  
Low Power ◽  
Low Voltage ◽  
Supply Voltage ◽  
Cmos Process ◽  
Slew Rate ◽  
Large Signal ◽  
Output Stage ◽  
Ultra Low Power ◽  
Input Stage ◽  
Rail To Rail

In this paper, we present a novel operational transconductance amplifier (OTA) topology based on a dual-path body-driven input stage that exploits a body-driven current mirror-active load and targets ultra-low-power (ULP) and ultra-low-voltage (ULV) applications, such as IoT or biomedical devices. The proposed OTA exhibits only one high-impedance node, and can therefore be compensated at the output stage, thus not requiring Miller compensation. The input stage ensures rail-to-rail input common-mode range, whereas the gate-driven output stage ensures both a high open-loop gain and an enhanced slew rate. The proposed amplifier was designed in an STMicroelectronics 130 nm CMOS process with a nominal supply voltage of only 0.3 V, and it achieved very good values for both the small-signal and large-signal Figures of Merit. Extensive PVT (process, supply voltage, and temperature) and mismatch simulations are reported to prove the robustness of the proposed amplifier.

Low-Power and Reference-Less Data and Clock Recovery Circuit for Visible Light Receivers

2018 ◽  
Author(s):  
Ming-Cheng Liu ◽  
Paul C.-P. Chao ◽  
Soh Sze Khiong
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
Visible Light ◽  
Low Voltage ◽  
Supply Voltage ◽  
Clock And Data Recovery ◽  
Optical Receiver ◽  
Clock Recovery ◽  
Cmos Process ◽  
Rf Receiver

In this paper a low power all-digital clock and data recovery (ADCDR) with 1Mhz frequency has been proposed. The proposed circuit is designed for optical receiver circuit on the battery-less photovoltaic IoT (Internet of Things) tags. The conventional RF receiver has been replaced by the visible light optical receiver for battery-less IoT tags. With this proposed ADCDR a low voltage, low power consumption & tiny IoT tags can be fabricated. The proposed circuit achieve the maximum bandwidth of 1MHz, which is compatible with the commercial available LED and light sensor. The proposed circuit has been fabricated in TSMC 0.18um 1P6M standard CMOS process. Experimental results show that the power consumption of the optical receiver is approximately 5.58uW with a supply voltage of 1V and the data rate achieves 1Mbit/s. The lock time of the ADCDR is 0.893ms with 3.31ns RMS jitter period.

scholarly journals A 2.5 Gbps, 10-Lane, Low-Power, LVDS Transceiver in 28 nm CMOS Technology

Electronics ◽  
2019 ◽  
Vol 8 (3) ◽  
pp. 350 ◽  
Author(s):  
Xu Bai ◽  
Jianzhong Zhao ◽  
Shi Zuo ◽  
Yumei Zhou
Keyword(s):  
Low Power ◽  
High Speed ◽  
Low Voltage ◽  
Cmos Technology ◽  
Common Mode ◽  
Serial Interface ◽  
Common Mode Voltage ◽  
Rail To Rail ◽  
The Common ◽  
28 Nm

This paper presents a 2.5 Gbps 10-lane low-power low voltage differential signaling (LVDS) transceiver for a high-speed serial interface. In the transmitter, a complementary MOS H-bridge output driver with a common mode feedback (CMFB) circuit was used to achieve a stipulated common mode voltage over process, voltage and temperature (PVT) variations. The receiver was composed of a pre-stage common mode voltage shifter and a rail-to-rail comparator. The common mode voltage shifter with an error amplifier shifted the common mode voltage of the input signal to the required range, thereby the following rail-to-rail comparator obtained the maximum transconductance to recover the signal. The chip was fabricated using SMIC 28 nm CMOS technology, and had an area of 1.46 mm2. The measured results showed that the output swing of the transmitter was around 350 mV, with a root-mean-square (RMS) jitter of 3.65 [email protected] Gbps, and the power consumption of each lane was 16.51 mW under a 1.8 V power supply.

A LOW POWER CRYOGENIC CMOS ROIC DESIGN FOR 512 × 512 IRFPA

2013 ◽  
Vol 22 (10) ◽  
pp. 1340033 ◽  
Author(s):  
HONGLIANG ZHAO ◽  
YIQIANG ZHAO ◽  
YIWEI SONG ◽  
JUN LIAO ◽  
JUNFENG GENG
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
Integrated Circuit ◽  
High Performance ◽  
Supply Voltage ◽  
Cmos Technology ◽  
High Gain ◽  
Readout Integrated Circuit ◽  
Chip Area ◽  
Operating Modes

A low power readout integrated circuit (ROIC) for 512 × 512 cooled infrared focal plane array (IRFPA) is presented. A capacitive trans-impedance amplifier (CTIA) with high gain cascode amplifier and inherent correlated double sampling (CDS) configuration is employed to achieve a high performance readout interface for the IRFPA with a pixel size of 30 × 30 μm2. By optimizing column readout timing and using two operating modes in column amplifiers, the power consumption is significantly reduced. The readout chip is implemented in a standard 0.35 μm 2P4M CMOS technology. The measurement results show the proposed ROIC achieves a readout rate of 10 MHz with 70 mW power consumption under 3.3 V supply voltage from 77 K to 150 K operating temperature. And it occupies a chip area of 18.4 × 17.5 mm2.

scholarly journals Effects of the Target on the Performance of an Ultra-Low Power Eddy Current Displacement Sensor for Industrial Applications

Electronics ◽  
2020 ◽  
Vol 9 (8) ◽  
pp. 1287
Author(s):  
Alessandro Bertacchini ◽  
Marco Lasagni ◽  
Gabriele Sereni
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
Eddy Current ◽  
Supply Voltage ◽  
Low Cost ◽  
Industrial Applications ◽  
Complete Characterization ◽  
Displacement Sensor ◽  
Ultra Low Power ◽  
Industry Automation

The demand for smart, low-power, and low-cost sensors is rapidly increasing with the proliferation of industry automation. In this context, an Ultra-Low Power Eddy Current Displacement Sensor (ULP-ECDS) targeting common industrial applications and designed to be embedded in wireless Industrial Internet of Things (IIoT) devices is presented. A complete characterization of the realized ULP-ECDS operating with different metallic targets was carried out. The choice of the considered targets in terms of material and thickness was inspired by typical industrial scenarios. The experimental results show that the realized prototype works properly with extremely low supply voltages, allowing for obtaining an ultra-low power consumption, significantly lower than other state-of-the-art solutions. In particular, the proposed sensor reached the best resolution of 2 µm in case of a carbon steel target when operated with a supply voltage of 200 mV and with a power consumption of 150 µW. By accepting a resolution of 12 µm, it is possible to further reduce the power consumption of the sensor to less than 10 µW. The obtained results also demonstrate how the performances of the sensor are strongly dependent on both the target and the demodulation technique used to extract the displacement information. This allowed for defining some practical guidelines that can help the design of effective solutions considering application-specific constraints.

Analytical Modeling of D.C. Parameters of Double Gate Junctionless MOSFET in Near and Subthreshold Regime for RF Circuit Application

2020 ◽  
Vol 10 (4) ◽  
pp. 457-470 ◽  
Author(s):  
Dipanjan Sen ◽  
Savio J. Sengupta ◽  
Swarnil Roy ◽  
Manash Chanda ◽  
Subir K. Sarkar
Keyword(s):  
Power Consumption ◽  
Low Power ◽  
Circuit Design ◽  
Power Dissipation ◽  
Supply Voltage ◽  
Dominant Factor ◽  
Double Gate ◽  
Cmos Inverter ◽  
Ultra Low Power ◽  
Voltage Swing

Aims:: In this work, a Junction-Less Double Gate MOSFET (JLDG MOSFET) based CMOS inverter circuit is proposed for ultra-low power applications in the near and sub-threshold regime operations. Background:: D.C. performances like power, delay and voltage swing of the proposed Inverter have been modeled analytically and analyzed in depth. JLDG MOSFET has promising features to reduce the short-channel effects compared to the planner MOSFET because of better gate control mechanism. So, proposed Inverter would be efficacious to offer less power dissipation and higher speed. Objective:: Impact of supply voltage, temperature, High-k gate oxide, TOX, TSI on the power, delay and voltage swing of the Inverter circuits have been detailed here. Methods: Extensive simulations using SILVACO ATLAS have been done to validate the proposed logic based digital circuits. Besides, the optimum supply voltage has been modelled and verified through simulation for low voltage operations. In depth analysis of voltage swing is added to measure the noise immunity of the proposed logic based circuits in Sub & Near-threshold operations. For ultra-low power operation, JLDG MOSFET can be an alternative compared to conventional planar MOSFET. Result:: Hence, the analytical model of delay, power dissipation and voltage swing have been proposed of the proposed logic based circuits. Besides, the ultra-low power JLDG CMOS inverter can be an alternative in saving energy, reduction of power consumption for RFID circuit design where the frequency range is a dominant factor. Conclusion:: The power consumption can be lowered in case of UHF, HF etc. RF circuits using the Double Gate Junction-less MOSFET as a device for circuit design.

Sign in / Sign up

Export Citation Format

Share Document