scholarly journals The Effects of Micro-Segregation on Isothermal Transformed Nano Bainitic Microstructure and Mechanical Properties in Laser Cladded Coatings

Materials ◽  
2020 ◽  
Vol 13 (13) ◽  
pp. 3017
Author(s):  
Yanbing Guo ◽  
Zhuguo Li ◽  
Liqun Li ◽  
Kai Feng
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
Volume Fraction ◽  
High Strength ◽  
Isothermal Heat Treatment ◽  
Isothermal Temperature ◽  
Bainitic Microstructure ◽  
Microstructure Morphology ◽  
Tunable Mechanical Properties ◽  
The Stability

The design of metastable retained austenite is the key issue to obtain nano bainitic steel with high strength and toughness. In this study, nanostructured Fe-based bainitic coatings were fabricated using laser cladding and following isothermal heat treatment. The microstructures and mechanical properties of the laser cladded coating were investigated. The results show that the Mn, Cr, Co, and Al segregated at the solidified prior grain boundaries. The micro-segregation of the solutes strongly influenced the stability of the austenite. As the isothermal temperature decreases, the interface of the bainite and blocky retained austenite approach to the prior interdendritic regions with the decreasing isothermal temperature, and the final volume fraction also decreases. The volume fractions of each phase and microstructure morphology of the coatings were determined by the interdendritic micro-segregation and isothermal temperatures. The stability of the blocky retained austenite distributed at the interdendritic area was lower than that of film and island-like morphology. This phenomenon contributed to the ductile and tough nano bainitic coatings with tunable mechanical properties.

Effect of Phosphorus on Microstructure, Mechanical Properties, and Formation of Retained Austenite in TRIP Steels

2012 ◽  
Vol 508 ◽  
pp. 128-132 ◽  
Author(s):  
Eui Pyo Kwon ◽  
Shun Fujieda ◽  
Kozo Shinoda ◽  
Shigeru Suzuki
Keyword(s):  
Mechanical Properties ◽  
Carbon Concentration ◽  
Trip Steel ◽  
Retained Austenite ◽  
Volume Fraction ◽  
Transformation Induced Plasticity ◽  
Trip Steels ◽  
The Stability

In this Study, Influences of P on the Microstructure, Mechanical Properties, and Retained Austenite Characteristics in Transformation Induced Plasticity (TRIP) Steels Were Investigated. Microstructure of 0.2mass%P Containing TRIP Steel Was Inhomogeneous and it Resulted in Deterioration of the Mechanical Properties. Retained Austenite Characteristics such as Volume Fraction and Carbon Concentration Were Also Affected by P. The Stability of Retained Austenite in P Containing TRIP Steel Was Different from that in P-Free TRIP Steel. Such Difference in the Stability of Retained Austenite Was Attributed to the Effect of the Carbon Concentration in Retained Austenite as Well as their Different Microstructure.

scholarly journals Controlling the Content and Morphology of Phase Constituents in Nanobainitic Steel Containing 0.6%C to Obtain the Required Ratio of Strength to Plasticity

Metals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 658
Author(s):  
Jarosław Marcisz ◽  
Bogdan Garbarz ◽  
Aleksandra Janik ◽  
Władysław Zalecki
Keyword(s):  
Mechanical Properties ◽  
Phase Composition ◽  
Retained Austenite ◽  
Volume Fraction ◽  
Total Elongation ◽  
Isothermal Transformation ◽  
Effect Of Temperature ◽  
Isothermal Heat Treatment ◽  
Dilatometric Studies ◽  
Kinetics Of

The phase composition of nanobainitic steel 0.56–0.60%C, 1.68–1.95%Mn, 1.58–1.80%Si, 1.30–1.47%Cr, 0.57–0.75%Mo is described in this paper. The phase composition is controlled in order to obtain diversified mechanical properties for specific applications, such as armor plates. The effect of temperature and time of isothermal heat treatment on both the microstructure and the mechanical properties of the steel were determined. Dilatometric studies, as well as measurements of volume fraction and size distribution of retained austenite were carried out. Analysis of the kinetics of isothermal transformation in the temperature range of 200–225 °C for times of up to 144 h were also carried out, and the parameters of the production process of the steel were determined. A microstructure consisting of nanolathy carbideless bainite and blocky and lathy retained austenite, providing tensile strength of at least 2000 MPa, yield strength of at least 1300 MPa, and total elongation of at least 10% has been found.

scholarly journals Effect of Pre-Quenching Process on Microstructure and Mechanical Properties in a Nb-Microalloyed Low Carbon Q-P Steel

2015 ◽  
Vol 816 ◽  
pp. 729-735 ◽  
Author(s):  
Jun Zhang ◽  
Hua Ding ◽  
Jing Wei Zhao
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
Room Temperature ◽  
Volume Fraction ◽  
Total Elongation ◽  
Trip Effect ◽  
Low Carbon ◽  
Quenching And Partitioning ◽  
The Stability ◽  
Critical Annealing

A refined microstructure consisting of martensite and retained austenite at room temperature has been produced in a Nb-microalloyed low carbon Si-Mn steel by a novel heat-treatment, pre-quenching prior to quenching and partitioning processes (Q&Q-P). The results showed that compared with the conventional quenching and partitioning steel the mechanical properties of steel obtained by the novel treatment have been significantly improved, with a good combination of ultimate tensile strength (1000MPa) and total elongation (above 30%). Meanwhile, the volume fraction of retained austenite has been increased. It was found that the improvement of mechanical properties was mainly attributed to the enhanced TRIP effect due to the relatively high fraction of metastable retained austenite at room temperature. The increased stability of austenite results from the C and Mn partitioning during inter-critical annealing, which increased the chemical stability of austenite. The formation of refined austenite at inter-critical annealing also had a positive effect on the stability of the austenite. As a consequence, the volume fraction of retained austenite at room temperature was significantly increased. Compared with the Q-P steel, the Q&Q-P steel exhibited higher work hardening exponents during the stage of TRIP effect and had the higher ductility.

Designing, Processing and Isothermal Transformation of Al-Si Medium Carbon Ultrafine High Strength Bainitic Steel

2017 ◽  
Vol 380 ◽  
pp. 1-11
Author(s):  
Sherif Ali Abd El Rahman ◽  
Ahmed Shash ◽  
Mohamed K. El-Fawkhry ◽  
Ahmed Zaki Farahat ◽  
Taha Mattar
Keyword(s):  
Mechanical Properties ◽  
Carbon Steel ◽  
Retained Austenite ◽  
High Carbon Steel ◽  
Bainitic Ferrite ◽  
High Strength ◽  
Isothermal Transformation ◽  
High Carbon ◽  
Medium Carbon ◽  
The Stability

Medium-carbon, silicon-rich steels are commonly suggested to obtain a very fine bainitic microstructure at a low temperature slightly above Ms. Thereby, the resulted microstructure consists of slender bainitic-ferritic plates interwoven with retained austenite. The advanced strength and ductility package of this steel is much dependent on the fineness of bainitic ferrite, as well as the retained austenite phase. In this article, the aluminum to silicon ratio, and the isothermal transformation temperature have been adopted to obtain ultra-high strength high carbon steel. Optical and SEM investigation of the produced steels have been performed. XRD has been used to track the retained austenite development as a result of the change in the chemical composition of developed steels and heat treatment process. Mechanical properties in terms of hardness and microhardness of obtained phases and structure were investigated. Results show that the increment of aluminum to silicon ratio has a great effect in promoting the bainitic transformation, in tandem with improving the stability and the fineness of retained austenite. Such an advanced structure leads to enhancement in the whole mechanical properties of the high carbon steel.

scholarly journals The Effect of Mn and Si on the Properties of Advanced High Strength Steels Processed by Quenching and Partitioning

2010 ◽  
Vol 654-656 ◽  
pp. 94-97 ◽  
Author(s):  
Bohuslav Mašek ◽  
Hana Jirková ◽  
Daniela Hauserova ◽  
Ludmila Kučerová ◽  
Danuše Klauberová
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
Volume Fraction ◽  
High Strength Steels ◽  
High Strength ◽  
Microstructural Development ◽  
X Ray Diffraction ◽  
Quenching And Partitioning ◽  
Advanced High Strength Steels ◽  
High Ultimate Strength

The concepts new types of materials are, for economic reasons, focused mainly on low alloyed steels with a good combination of strength and ductility. Suitable heat and thermo-mechanical treatments play an important role for the utilization of these materials. Different alloying strategies are used to influence phase transformations. The quenching and partitioning process (Q-P Process) is one of the heat treatment methods which can result in a high ultimate strength as well as a good ductility. However, these good properties can be obtained only if a sufficient amount of retained austenite is stabilized. The influence of different contents of manganese, silicon and chromium on microstructural development and mechanical properties were experimentally tested. Alloying elements were used to stabilize the retained austenite in the final microstructure and also to strengthen the solid solution. Ultimate strengths of over 2000MPa with ductility over 10% were reached after the optimization of the Q-P Process. The microstructures were analyzed using several microscopic methods; mechanical properties were determined by a tensile test and the volume fraction of the retained austenite was established by X-ray diffraction phase analysis.

Microstructure Development and Mechanical Properties of a Hot Stamped Low-Carbon Advanced High Strength Steel Treated by a Novel Dynamic Carbon Partitioning Process

2014 ◽  
Vol 1063 ◽  
pp. 42-46 ◽  
Author(s):  
Fei Bao Zhang ◽  
Hong Wu Song ◽  
Ming Cheng ◽  
Xin Li ◽  
Shi Hong Zhang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
Volume Fraction ◽  
Hot Stamping ◽  
High Strength ◽  
Carbon Partitioning ◽  
Martensite Phase ◽  
Low Carbon ◽  
Step Method ◽  
The Impact

To make steel exhibit attractive properties as high strength and good ductility, this paper presents a novel one step method for forming-Q&P integration—Hot Stamping-Dynamic Partitioning (HS-DP) process. The proposed HS-DP process is simulated with salt bath heat treatment. The effect of microstructure and mechanical properties in a low-carbon AHSS with different cooling rate of the new process is investigated by using scanning electron microscopy (SEM), X-ray diffraction (XRD) and tensile test methods. Microstructure of the steel subjected to HS-DP treatment is mainly composed of initial quenched martensite phase , final quenched martensite phase and retained austenite phase formed. The impact of retained austenite is also discussed, especially the influence of elongation caused by various retained austenite volume fraction and carbon-content. This experiment illustrates the promising application potential of the hot stamping-dynamic carbon partitioning process.

scholarly journals EFFECTS OF COOLING RATE ON THE VOLUME FRACTION OF RETAINED AUSTENITE IN FORGINGS FROM HIGH-STRENGTH Mn-Si STEELS

2019 ◽  
Vol 25 (2) ◽  
pp. 93 ◽  
Author(s):  
Dagmar Bublíková ◽  
Hana Jirková ◽  
Kateřina Rubešová ◽  
Michal Peković ◽  
Julie Volkmannová ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Cooling Rate ◽  
Retained Austenite ◽  
Physical Simulation ◽  
Volume Fraction ◽  
High Strength ◽  
Hot Water ◽  
Quenching Temperature ◽  
Soaking Temperature

<p class="AMSmaintext"><span lang="EN-GB">Various ways are sought today to increase mechanical properties of steels while maintaining their good strength and ductility. Besides effective alloying strategies, one method involves preserving a certain amount of retained austenite in a martensitic matrix. The steel which was chosen as an experimental material for this investigation contained 2.5% manganese, 2.09% silicon and 1.34% chromium, with additions of nickel and molybdenum. An actual closed-die forged part was made of this steel. This forged part was fitted with thermocouples attached to its surface and placed in its interior and then treated using the Q&amp;P process. Q&amp;P process is characterized by rapid cooling from a soaking temperature to a quenching temperature, which is between the Ms and the Mf, and subsequent reheating to and holding at a partitioning temperature where retained austenite becomes stable. The quenchant was hot water. Cooling took place in a furnace. Heat treatment profiles were constructed from the thermocouple data and the process was then replicated in a thermomechanical simulator. The specimens obtained in this manner were examined using metallographic techniques. The effects of cooling rate on mechanical properties and the amount of retained austenite were assessed. The resultant ultimate strength was around 2100 MPa. Elongation and the amount of retained austenite were 15% and 17%, respectively. Microstructures and mechanical properties of the specimens were then compared to the real-world forged part in order to establish whether physical simulation could be employed for laboratory-based optimization of heat treatment of forgings.</span></p>

scholarly journals Mechanical Properties of Low-Temperature Bainite

2005 ◽  
Vol 500-501 ◽  
pp. 495-502 ◽  
Author(s):  
Carlos García-Mateo ◽  
Francisca García Caballero ◽  
Harshad K.D.H. Bhadeshia
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Retained Austenite ◽  
High Strength ◽  
Isothermal Transformation ◽  
Fine Scale ◽  
Bainitic Microstructure ◽  
Unusual Combination

The mechanical properties of a bainitic microstructure with slender ferrite plates (20-65 nm in thickness) in a matrix of carbon-enriched retained austenite were characterized. The microstructure is generated by isothermal transformation at temperatures in the range 200-300°C. A yield strength as high as 1.5 GPa and an ultimate tensile strength between 1.77 to 2.2 GPa was achieved, depending on the transformation temperature. Furthermore, the high strength is frequently accompanied by ductility (£ 30%) and respectable levels of fracture toughness (< 45 MPa m0.5). This unusual combination of properties is attributed to the exceptionally fine scale of the carbidefree bainitic microstructure and the associated retained austenite.

Effect of Si Content on Microstructure and Properties of 60Si2CrVA Spring Steel

2014 ◽  
Vol 968 ◽  
pp. 63-66 ◽  
Author(s):  
Fei Zhao ◽  
Zhan Ling Zhang ◽  
Jun Shuai Li ◽  
Cui Ye ◽  
Ni Li
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
Volume Fraction ◽  
Testing Machine ◽  
Spring Steel ◽  
Impact Testing ◽  
X Ray ◽  
Comprehensive Properties ◽  
Spring Steels ◽  
Si Content

The microstructure and mechanical properties of the four spring steels with different Si content treated by Q-I-Q-T process were studied by metallographic microscope, MTS, impact testing machine and X-ray stress analyzer. The results show that the tensile strength and yield strength is first increased and then decreased with the increase of Si content, the volume fraction of retained austenite and elongation are fist decreased and then increased when the Si content is less than 2.1%, and the microstructure become finer and homogeneous. When Si content reaches 2.1%, the comprehensive properties of 60Si2CrVA spring steel is the best.

scholarly journals Carbon Redistribution and Microstructural Evolution Study during Two-Stage Quenching and Partitioning Process of High-Strength Steels by Modeling

Materials ◽  
2018 ◽  
Vol 11 (11) ◽  
pp. 2302 ◽  
Author(s):  
Yilin Wang ◽  
Huicheng Geng ◽  
Bin Zhu ◽  
Zijian Wang ◽  
Yisheng Zhang
Keyword(s):  
Retained Austenite ◽  
Volume Fraction ◽  
High Strength Steels ◽  
High Strength ◽  
Simulation Method ◽  
Low Carbon ◽  
Two Stage ◽  
Quenching And Partitioning ◽  
Carbon Redistribution ◽  
Carbon Martensite

The application of the quenching and partitioning (Q-P) process on advanced high-strength steels improves part ductility significantly with little decrease in strength. Moreover, the mechanical properties of high-strength steels can be further enhanced by the stepping-quenching-partitioning (S-Q-P) process. In this study, a two-stage quenching and partitioning (two-stage Q-P) process originating from the S-Q-P process of an advanced high-strength steel 30CrMnSi2Nb was analyzed by the simulation method, which consisted of two quenching processes and two partitioning processes. The carbon redistribution, interface migration, and phase transition during the two-stage Q-P process were investigated with different temperatures and partitioning times. The final microstructure of the material formed after the two-stage Q-P process was studied, as well as the volume fraction of the retained austenite. The simulation results indicate that a special microstructure can be obtained by appropriate parameters of the two-stage Q-P process. A mixed microstructure, characterized by alternating distribution of low carbon martensite laths, small-sized low-carbon martensite plates, retained austenite and high-carbon martensite plates, can be obtained. In addition, a peak value of the volume fraction of the stable retained austenite after the final quenching is obtained with proper partitioning time.

Sign in / Sign up

Export Citation Format

Share Document