scholarly journals Mechanical Properties of Low-Temperature Bainite

2005 ◽  
Vol 500-501 ◽  
pp. 495-502 ◽  
Author(s):  
Carlos García-Mateo ◽  
Francisca García Caballero ◽  
Harshad K.D.H. Bhadeshia
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Retained Austenite ◽  
High Strength ◽  
Isothermal Transformation ◽  
Fine Scale ◽  
Bainitic Microstructure ◽  
Unusual Combination

The mechanical properties of a bainitic microstructure with slender ferrite plates (20-65 nm in thickness) in a matrix of carbon-enriched retained austenite were characterized. The microstructure is generated by isothermal transformation at temperatures in the range 200-300°C. A yield strength as high as 1.5 GPa and an ultimate tensile strength between 1.77 to 2.2 GPa was achieved, depending on the transformation temperature. Furthermore, the high strength is frequently accompanied by ductility (£ 30%) and respectable levels of fracture toughness (< 45 MPa m0.5). This unusual combination of properties is attributed to the exceptionally fine scale of the carbidefree bainitic microstructure and the associated retained austenite.

scholarly journals Achievement of High Strength and Ductility in Al–Si–Cu–Mg Alloys by Intermediate Phase Optimization in As-Cast and Heat Treatment Conditions

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 647 ◽  
Author(s):  
Bingrong Zhang ◽  
Lingkun Zhang ◽  
Zhiming Wang ◽  
Anjiang Gao
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Intermediate Phase ◽  
High Strength ◽  
Mg Alloys ◽  
Artificial Ageing ◽  
Treatment Conditions ◽  
Eutectic Si

In order to obtain high-strength and high-ductility Al–Si–Cu–Mg alloys, the present research is focused on optimizing the composition of soluble phases, the structure and morphology of insoluble phases, and artificial ageing processes. The results show that the best matches, 0.4 wt% Mg and 1.2 wt% Cu in the Al–9Si alloy, avoided the toxic effect of the blocky Al2Cu on the mechanical properties of the alloy. The addition of 0.6 wt% Zn modified the morphology of eutectic Si from coarse particles to fine fibrous particles and the texture of Fe-rich phases from acicular β-Fe to blocky π-Fe in the Al–9Si–1.2Cu–0.4Mg-based alloy. With the optimization of the heat treatment parameters, the spherical eutectic Si and the fully fused β-Fe dramatically improved the ultimate tensile strength and elongation to fracture. Compared with the Al–9Si–1.2Cu–0.4Mg-based alloy, the 0.6 wt% Zn modified alloy not only increased the ultimate tensile strength and elongation to fracture of peak ageing but also reduced the time of peak ageing. The following improved combination of higher tensile strength and higher elongation was achieved for 0.6 wt% Zn modified alloy by double-stage ageing: 100 °C × 3 h + 180 °C × 7 h, with mechanical properties of ultimate tensile strength (UTS) of ~371 MPa, yield strength (YS) of ~291 MPa, and elongation to fracture (E%) of ~5.6%.

scholarly journals Microstructure and Mechanical Properties of Tempered Ausrolled Nanobainite Steel

Crystals ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 573
Author(s):  
Jing Zhao ◽  
Dezheng Liu ◽  
Yan Li ◽  
Yongsheng Yang ◽  
Tiansheng Wang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Retained Austenite ◽  
Volume Fraction ◽  
Bainitic Ferrite ◽  
Energy Yield ◽  
Partial Recovery ◽  
Fracture Appearance ◽  
The Impact

The microstructures and mechanical properties of ausrolled nanobainite steel, after being tempered at temperatures in the range of 200−400 °C, were investigated in this study. After being tempered, bainitic ferrite is coarsened and the volume fraction of retained austenite is reduced. The hardness and ultimate tensile strength decrease sharply. The impact energy, yield strength, and elongation increase with elevated tempered temperature at 200–300 °C but decrease with elevated tempered temperature when the samples are tempered at 350 °C and 400 °C. The fracture appearance of all the samples after impact tests is a brittle fracture. The variation of the mechanical properties may be due to partial recovery and recrystallization.

Development of Laminar Flow Cooling of Ultra-High Strength Ferrite-Bainite Dual Phase Steel

2012 ◽  
Vol 184-185 ◽  
pp. 940-943
Author(s):  
Wei Lv ◽  
Di Wu ◽  
Zhuang Li
Keyword(s):  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Laminar Flow ◽  
Hot Rolling ◽  
Retained Austenite ◽  
High Strength ◽  
Total Elongation ◽  
Granular Bainite ◽  
Dual Phase ◽  
Dp Steel

In the present paper, controlled cooling in different ways was performed using a laboratory hot rolling mill in ultra-high strength hot rolled ferrite-bainite dual phase (DP) steel. The results have shown that the final microstructures of DP steel comprise ferrite, bainite and a small amount of retained austenite and martensite. DP steel has a tensile strength ranging from 1010 to 1130MPa and yet retains considerable total elongation in the range of 14–17%. The addition of Mn and Nb to DP steel leads to the maximum ultimate tensile strength, yield strength and the product of ultimate tensile strength and total elongation due to the formation of retained austenite and granular bainite structure. Laminar flow cooling after hot rolling results in a significant increase in the quantity of ferrite and bainite due to the suppression of pearlite transformation, and as a result, the present steel possesses high strengths and good toughness.

scholarly journals Effect of Heat Treatment on Mechanical Properties and Microstructure Morphology of Low-Alloy High-Strength Steel

2016 ◽  
Vol 61 (2) ◽  
pp. 475-480
Author(s):  
K. Bolanowski
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Yield Strength ◽  
High Strength Steel ◽  
High Strength ◽  
Strengthening Phase ◽  
Average Grain Size

Abstract The paper analyzes the influence of different heat treatment processes on the mechanical properties of low-alloy high-strength steel denoted by Polish Standard (PN) as 10MnVNb6. One of the findings is that, after aging, the mechanical properties of rolled steel are high: the yield strength may reach > 600 MPa, and the ultimate tensile strength is > 700 MPa. These properties are largely dependent on the grain size and dispersion of the strengthening phase in the ferrite matrix. Aging applied after hot rolling contributes to a considerable rise in the yield strength and ultimate tensile strength. The process of normalization causes a decrease in the average grain size and coalescence (reduction of dispersion) of the strengthening phase. When 10MnVNb6 steel was aged after normalization, there was not a complete recovery in its strength properties.

Microstructure and Mechanical Properties of TRIP-Aided Steels with Different Heat Treatments

2015 ◽  
Vol 817 ◽  
pp. 439-443 ◽  
Author(s):  
Rui Dong ◽  
Ai Min Zhao ◽  
Ran Ding ◽  
Jian Guo He ◽  
Han Jiang Hu
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Retained Austenite ◽  
Volume Fraction ◽  
Total Elongation ◽  
Heat Treatments ◽  
Second Phase ◽  
Soft Matrix ◽  
Significant Difference

The microstructures, mechanical properties and retained austenite characteristics of TRIP-aided steels with three different heat treatments were studied in this paper. The results indicated that the designed annealing treatments resulted in completely different matrices and the morphologies of second phase, and a significant difference in mechanical properties. The TAM steel was found to have fine annealed martensite lath matrix and inter lath acicular retained austenite, and possessed an excellent combination of strength and elongation which attributed to the highest retained austenite volume fraction and carbon concentration. For TPF steel, the higher instability and lower carbon content of retained austenite and the soft matrix resulted in the lowest ultimate tensile strength and total elongation. While in TBF steel, the stability of retained austenite was lower than that in TAM steel but higher than that in TPF steel. The ultimate tensile strength of TBF was significantly higher than the TAM and TPF steels, but the ductility of TBF steel was lower than TAM steel.

VASCOJET 1000-5 TEMPER

Alloy Digest ◽  
1961 ◽  
Vol 10 (1) ◽  
Keyword(s):  
Fracture Toughness ◽  
Tensile Strength ◽  
High Temperature ◽  
Ultimate Tensile Strength ◽  
High Strength ◽  
Heat Treating ◽  
Steel Company ◽  
Vanadium Alloys ◽  
Temperature Performance ◽  
Ultra High Strength Steel

Abstract Vascojet 1000-5 Temper is an ultra high-strength steel designed for applications requiring between 300,000 and 325,000 psi ultimate tensile strength, and 260,000-270,000 psi yield strength, with good fatigue and impact properties. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness and fatigue. It also includes information on low and high temperature performance as well as forming, heat treating, machining, joining, and surface treatment. Filing Code: SA-109. Producer or source: Vanadium-Alloys Steel Company.

scholarly journals The Effects of Micro-Segregation on Isothermal Transformed Nano Bainitic Microstructure and Mechanical Properties in Laser Cladded Coatings

Materials ◽  
2020 ◽  
Vol 13 (13) ◽  
pp. 3017
Author(s):  
Yanbing Guo ◽  
Zhuguo Li ◽  
Liqun Li ◽  
Kai Feng
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
Volume Fraction ◽  
High Strength ◽  
Isothermal Heat Treatment ◽  
Isothermal Temperature ◽  
Bainitic Microstructure ◽  
Microstructure Morphology ◽  
Tunable Mechanical Properties ◽  
The Stability

The design of metastable retained austenite is the key issue to obtain nano bainitic steel with high strength and toughness. In this study, nanostructured Fe-based bainitic coatings were fabricated using laser cladding and following isothermal heat treatment. The microstructures and mechanical properties of the laser cladded coating were investigated. The results show that the Mn, Cr, Co, and Al segregated at the solidified prior grain boundaries. The micro-segregation of the solutes strongly influenced the stability of the austenite. As the isothermal temperature decreases, the interface of the bainite and blocky retained austenite approach to the prior interdendritic regions with the decreasing isothermal temperature, and the final volume fraction also decreases. The volume fractions of each phase and microstructure morphology of the coatings were determined by the interdendritic micro-segregation and isothermal temperatures. The stability of the blocky retained austenite distributed at the interdendritic area was lower than that of film and island-like morphology. This phenomenon contributed to the ductile and tough nano bainitic coatings with tunable mechanical properties.

scholarly journals Correlation between Microstructure and Mechanical Properties of Heat-Treated Ti–6Al–4V with Fe Alloying

Metals ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 854 ◽  
Author(s):  
Yongwei Liu ◽  
Fuwen Chen ◽  
Guanglong Xu ◽  
Yuwen Cui ◽  
Hui Chang
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Tensile Strength ◽  
Mechanical Performance ◽  
Volume Fraction ◽  
Phase Interface ◽  
High Strength ◽  
High Plasticity ◽  
High Aging Temperature ◽  
Microstructure And Mechanical Properties

The microstructure and mechanical properties of a newly developed Fe-microalloyed Ti–6Al–4V titanium alloy were investigated after different heat treatments. The volume fraction and the morphological features of the lamellar α phase had significant effects on the alloy’s mechanical performance. A dataset showing the relationship between microstructural features and tensile strength, elongation, and fracture toughness was developed. A high aging temperature resulted in high plasticity and fracture toughness, but relatively low strength. The high strength favored the fine α and the slender β. The high aspect ratio of lamellar α led to high strength but low fracture toughness. The alloy with ~84 vol % α exhibited the highest strength and lowest fracture toughness because the area of its α/β-phase interface was the highest. Optimal comprehensive mechanical performance and heat-treatment procedures were thus obtained from the dataset. Optimal tensile strength, yield strength, elongation, and fracture toughness were 999 and 919 MPa, 10.4%, and 94.4 MPa·m1/2, respectively.

Designing, Processing and Isothermal Transformation of Al-Si Medium Carbon Ultrafine High Strength Bainitic Steel

2017 ◽  
Vol 380 ◽  
pp. 1-11
Author(s):  
Sherif Ali Abd El Rahman ◽  
Ahmed Shash ◽  
Mohamed K. El-Fawkhry ◽  
Ahmed Zaki Farahat ◽  
Taha Mattar
Keyword(s):  
Mechanical Properties ◽  
Carbon Steel ◽  
Retained Austenite ◽  
High Carbon Steel ◽  
Bainitic Ferrite ◽  
High Strength ◽  
Isothermal Transformation ◽  
High Carbon ◽  
Medium Carbon ◽  
The Stability

Medium-carbon, silicon-rich steels are commonly suggested to obtain a very fine bainitic microstructure at a low temperature slightly above Ms. Thereby, the resulted microstructure consists of slender bainitic-ferritic plates interwoven with retained austenite. The advanced strength and ductility package of this steel is much dependent on the fineness of bainitic ferrite, as well as the retained austenite phase. In this article, the aluminum to silicon ratio, and the isothermal transformation temperature have been adopted to obtain ultra-high strength high carbon steel. Optical and SEM investigation of the produced steels have been performed. XRD has been used to track the retained austenite development as a result of the change in the chemical composition of developed steels and heat treatment process. Mechanical properties in terms of hardness and microhardness of obtained phases and structure were investigated. Results show that the increment of aluminum to silicon ratio has a great effect in promoting the bainitic transformation, in tandem with improving the stability and the fineness of retained austenite. Such an advanced structure leads to enhancement in the whole mechanical properties of the high carbon steel.

Effect of Tempering Temperature on Microstructure and Properties of Low Carbon High Silicon Alloy Steel Treated by Q-P-T Process

2020 ◽  
Vol 993 ◽  
pp. 592-596
Author(s):  
Jun Hu Wei ◽  
Xu Ran ◽  
Han Ying
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Alloy Steel ◽  
Retained Austenite ◽  
Volume Fraction ◽  
Low Carbon ◽  
Tempering Temperature ◽  
Silicon Alloy ◽  
High Silicon

The mechanical properties and microstructure of low-carbon high-silicon alloy steel were examined under various tempering temperatures using the quenching, partitioning and tempering (Q–P–T) process. The performance changed with the variation in tempering temperature. The results show that the microstructure of low carbon high silicon alloy steel treated by Q-P-T process was mainly ferrite, martensite, carbide-free bainite and film-like retained austenite. This alloys exhibited good mechanical properties at tempering temperature of 300 °C. The product of strength and elongation were 33.7 GPa%. Specifically, the Ultimate tensile strength were 1508 MPa, the yield strength were 1048 MPa, and the elongation were 22.4%. At this temperature of 300 °C, the volume fraction of retained austenite reached 10.4%.

Sign in / Sign up

Export Citation Format

Share Document