scholarly journals Strengthening and Weakening Effects of Particles on Strength and Ductility of SiC Particle Reinforced Al-Cu-Mg Alloys Matrix Composites

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1219
Author(s):  
Zhiyu Yang ◽  
Jianzhong Fan ◽  
Yanqiang Liu ◽  
Junhui Nie ◽  
Ziyue Yang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Particle Size ◽  
Yield Strength ◽  
Ultimate Strength ◽  
Fracture Morphology ◽  
Mg Alloys ◽  
Matrix Composites ◽  
Sic Particles ◽  
The Matrix ◽  
Strength And Ductility

The strengthening and weakening effects of SiC particles on composite strength and ductility were studied. Al-Cu-Mg alloys matrices with three different mechanical properties were used. Their yield strength, ultimate strength, and elongation range from 90 to 379 MPa, 131 to 561 MPa, and 18% to 31%, respectively. SiC particles with sizes of 4, 8, 12, 15, 20, and 30 μm were used to reinforce these three matrices, separately, and the composites of eighteen combinations of the particle sizes and matrix strengths were manufactured. Yield strength, ultimate strength, elongation, and fracture morphology of these composites were characterized. Based on the analysis, the strengthening to weakening behavior on strength and ductility were comprehensively discussed. The critical particle size having the best ductility was obtained. The strengthening limit and match range of the particle and the matrix to achieve effective strengthening were defined as a function of the particle size and matrix strength. This work offers an important reference for optimization of mechanical properties of the particle-reinforced metal matrix composites.

scholarly journals The Effect of Reinforcement Ratio on the Composite Structure and Mechanical Properties in Al-MgO Composites Produced by the Melt Stirring Method

2011 ◽  
Vol 20 (4) ◽  
pp. 096369351102000 ◽  
Author(s):  
Recep Çalin ◽  
Pul Muharrem ◽  
Ramazan Çitak ◽  
Ulvi Şeker
Keyword(s):  
Mechanical Properties ◽  
Particle Size ◽  
Metal Matrix ◽  
Vertical Direction ◽  
Homogeneous Distribution ◽  
Matrix Composites ◽  
Liquid Matrix ◽  
The Matrix ◽  
Micro Structures ◽  
Scanning Electron

In this study, Al- MgO metal matrix composites (MMC) were produced with 5 %, 10 % and 15 % reinforcement- volume (R-V) ratios by the melt stirring method. In the production of composites 99.5 % pure Al was used as the matrix and MgO powders with the particle size of −105 μm were used as the reinforcement. For every R-V ratio; stirring was made at 500 rev/min at 750°C liquid matrix temperature for 4 minutes and the samples were cooled under normal atmosphere. Then hardness and fracture strengths of the samples were determined and their micro structures were evaluated by using Scanning Electron Microscope (SEM). In general, it was observed that the reinforcement exhibited a homogeneous distribution in horizontal direction. But there is a slight inhomogeneity in vertical direction. It was determined that the increase in the R-V ratio increased the porosity and also the hardness. As for the fracture strength, the highest strength was obtained with the 5 % MgO reinforced sample.

Effects of Repeated Plastic Working (RPW) Process on the Structure and Properties of Mg2Si/Mg-Zn-Er Composite

2010 ◽  
Vol 146-147 ◽  
pp. 1222-1226
Author(s):  
Shu Bo Li ◽  
Ya Ling Qin ◽  
Han Li ◽  
Wen Bo Du
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Yield Strength ◽  
Ultimate Strength ◽  
Matrix Alloy ◽  
Structure And Properties ◽  
Plastic Working ◽  
Magnesium Matrix ◽  
The Matrix ◽  
Silicon Particles

The Mg matrix composite (Mg2Si/Mg-5Zn-2.5Er) was prepared using repeated plastic working (RPW) technique. and the effects of the number of RPW cycles on the microstructure and mechanical properties of these composites were investigated. The results indicated that the added silicon particles fully reacted with the magnesium matrix, and theMg2Si/Mg-5Zn-2.5Er composites were successfully achieved. When the number of RPW cycle increased, the size of the Mg2Si particles decreased, and the grain size of the matrix alloy reached the minimum when 200 RPW cycles was used. The best mechanical properties were also identified as 394 MPa ultimate strength, and 363 MPa yield strength, when 200 RPW cycles were used.

scholarly journals Influence of Grain Size and Texture on the Yield Strength of Mg Alloys Processed by Severe Plastic Deformation

2014 ◽  
Vol 2014 ◽  
pp. 1-9 ◽  
Author(s):  
Jinbao Lin ◽  
Weijie Ren ◽  
Qudong Wang ◽  
Lifeng Ma ◽  
Yongjun Chen
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Grain Size ◽  
Yield Strength ◽  
Severe Plastic Deformation ◽  
Flow Behavior ◽  
Influence Factors ◽  
Mg Alloys ◽  
Processing Conditions ◽  
Strength And Ductility

Severe plastic deformation (SPD) has been widely employed to refine the grain size of Mg alloys, with the main objective to improve the strength and ductility of Mg alloys, since the well-known Hall-Petch equation suggests that a decreased grain size leads to an increased yield strength. However, the yield strength of Mg alloys processed by SPD is often decreased even though the grain size is effectively reduced. The abnormal flow behavior in Mg alloys processed by SPD has attracted great attention although this mechanism is still unclear, due to its complex and extensive influence factors. In this paper, the relationships between the processing conditions, grain refinement, and mechanical properties of the SPD treated Mg alloys are reviewed, with the emphasis on the effects of grain size and texture on the yield strength.

Mechanical and Morphological Studies of Al6061-Gr-SiC Hybrid Metal Matrix Composites

2015 ◽  
Vol 813-814 ◽  
pp. 195-202 ◽  
Author(s):  
T. Lokesh ◽  
U.S. Mallikarjun
Keyword(s):  
Mechanical Properties ◽  
Metal Matrix Composites ◽  
Metal Matrix ◽  
Hybrid Composites ◽  
Matrix Material ◽  
Matrix Alloy ◽  
Matrix Composites ◽  
Morphological Studies ◽  
The Matrix ◽  
Strength And Ductility

Abstract. In recent years, Aluminium alloy based metal matrix composites (MMC) are gaining wide spread acceptance in several aerospace and automobile applications. These composites possess excellent wear resistance in addition to other superior mechanical properties such as strength, modulus and hardness when compared with conventional alloys. The hybrid composites are new generation of composites containing more than one type, shape or sizes of reinforcements giving superior combined properties of reinforcements and the matrix. In the present work, Al6061 has been used as matrix material and the reinforcing materials selected were SiC and Graphite particulates of 10 to 30µm size. Composites Al6061-Gr (2- 8 wt. %), Al6061-SiC (2 -10wt. %) and Hybrid composites with Al6061 matrix alloy containing 3wt% graphite and varying composition of 2-10wt% SiCp were prepared by stir casting technique. The cast matrix alloy and its composites have been subjected to solutionizing treatment at a temperature of 530 ± 20C for 6 hours, followed by ageing at a temperature of 175 ± 20C for 6 hours. The mechanical properties of as cast and T6 heat treated composites have been evaluated as per ASTM standards and compared. Addition of Graphite particulates into the Al6061 matrix improved the strength and ductility of the composites. Significant improvement in tensile strength and hardness was noticed as the wt. % of SiCp increases in Al6061-SiC composites. Addition of Graphite into Al6061-SiC further improved the strength and ductility of hybrid composites. The heat treatment process had the profound effect in improving the mechanical properties of the studied composites. The microstructural studies revealed the uniform distribution of SiC and Gr particles in the matrix system.

Effects of Particle Size and Distribution on the Microstructure and Mechanical Properties of SiC Reinforced Al-30Si Alloy Composite

2012 ◽  
Vol 271-272 ◽  
pp. 12-16 ◽  
Author(s):  
Zeng Lei Ni ◽  
Ai Qin Wang ◽  
Jing Pei Xie
Keyword(s):  
Mechanical Properties ◽  
Particle Size ◽  
Tensile Strength ◽  
Physical Properties ◽  
Combined Effects ◽  
Alloy Composite ◽  
Microstructure And Mechanical Properties ◽  
Sic Particles ◽  
The Matrix ◽  
Sic Particle

This paper studied the combined effects of particle size and distribution on the mechanical properties of the SiC particle reinforced Al-30Si alloy composites. The microstructure of experimental material was analyzed by SEM, the tensile strength and physical properties were examined. The results show that, with the increase of the SiC particle size in the composites, the clustering degree of the SiC particles decreases in the matrix, the SiC particles distribute more ununiformly. The tensile strength is influenced by the SiC particle size, the tensile strength of the composite reinforced by 13μm sized SiC particles is the highest.

Mechanical Properties of Csf/AZ91D Composites Fabricated by Extrusion Forming Process Directly Following the Vacuum Infiltration

2010 ◽  
Vol 89-91 ◽  
pp. 692-696 ◽  
Author(s):  
Ji Ming Zhou ◽  
Le Hua Qi ◽  
Hai Bo Ouyang ◽  
He Jun Li
Keyword(s):  
Mechanical Properties ◽  
Yield Strength ◽  
Short Fiber ◽  
Fiber Content ◽  
Vacuum Infiltration ◽  
Matrix Composites ◽  
Magnesium Matrix ◽  
Magnesium Matrix Composites ◽  
The Matrix ◽  
Strength And Stiffness

Magnesium matrix composites are attractive for weight critical application, such as automotive and aerospace components, because of its high specific strength and stiffness. Extrusion process directly following vacuum infiltration (EVI) can eliminate the porosity and obtain the well-aligned and uniform fiber distribution during the fabrication of Csf/AZ91D composite. This process combines the advantages of gas pressure infiltration, squeeze casting, and semi-solid extrusion. The mechanical properties of the magnesium are improved greatly by introducing the carbon fibers into the magnesium matrix through the EVI process. In the present study, the carbon short fiber reinforced magnesium matrix composites Csf/AZ91D were fabricated by EVI process. The microstructure and tensile property of Csf/AZ91D composites were investigated. The results showed that the microstructure of the composite presented a uniform distribution of carbon short fibers in the matrix and good interfacial integrity. The yield strength and stiffness of the composites increased with increasing carbon short fiber content, but at the cost of ductility. Nonetheless, Csf/AZ91D can keep relatively high ductility during the improvement of strength compared with reported composites in the literatures. Increasing carbon fiber content in the composite was not always beneficial to the ultimate tensile strength at the same magnitude. When the fiber content exceeds 10%, the matrix was not strengthened as greatly as under 10% fiber content. The yield strength improvement was attributed to (i) load-bearing effects due to the presence of carbon short fiber reinforcements; (ii) grain size refinement due to the large extrusion deformation; (iii) generation of dislocations to accommodate CTE mismatch between the matrix and the particles.

Role of SiC ceramic particles on the physical and mechanical properties of Al–4%Cu metal matrix composite fabricated via mechanical alloying

2016 ◽  
Vol 51 (9) ◽  
pp. 1285-1298 ◽  
Author(s):  
Mahnaz Keneshloo ◽  
Moslem Paidar ◽  
Morteza Taheri
Keyword(s):  
Mechanical Properties ◽  
Particle Size ◽  
Mechanical Alloying ◽  
Morphological Changes ◽  
Aluminum Matrix ◽  
Diffraction Method ◽  
Physical And Mechanical Properties ◽  
X Ray Diffraction ◽  
Sic Particles ◽  
The Matrix

In the present investigation, Al–Cu composites with SiC particulates were fabricated via mechanical alloying process. The aim of this study was to evaluate the effect of milling time (8, 12, 16 and 32 h), particle size (30 nm and 15 µm) and volume fractions (5, 10 and 15 wt.%) of SiC particles on the metallurgical and mechanical properties. Scanning electron microscopy equipped with X-ray diffraction method was used to investigate the microstructural evolution and morphological changes created during mechanical alloying. Microstructural study indicated that SiC particles were well distributed after the mechanical alloying process. A homogenous distribution of the particles was obtained by 15 wt.% of SiC particles in the aluminum matrix. The results revealed that the SiC particle size also affected the distribution and size of the powders in the matrix and it improved as particle size decreased from 15 µm to 30 nm. The study of mechanical properties clearly showed that a reduction in hardness of composite occurs which is attributed to positive effect of reinforcement particles in resistance to the movement of dislocations. Furthermore, it was found that the wear weight loss of Al–Cu/SiC composite decreases monotonically with increasing SiC content and more uniform particle size distribution. The excellent wear rate was primarily attributed to uniform distribution of the SiC particles.

Effect of Minor Additives on First Stage Graphitisation in White Cast Iron

1984 ◽  
Vol 34 ◽  
Author(s):  
P. L. Roy ◽  
A. K. Chakrabart ◽  
P. Banerjee
Keyword(s):  
Mechanical Properties ◽  
Cast Iron ◽  
Sodium Chloride ◽  
Yield Strength ◽  
White Cast Iron ◽  
Elemental Sulphur ◽  
Optimum Dose ◽  
White Iron ◽  
Kinetics Of ◽  
Strength And Ductility

ABSTRACTMinor additions (0.05-0.2 wt.%) of sodium chloride, hexachloroethane and elemental sulphur to commercial white iron melts have been found to enhance the kinetics of first stage graphitisation during subsequent annealing of white iron samples. The optimum dose of sodium chloride and hexachloroethane addition is around 0.1%. Yield strength and ductility of annealed test bars treated with NaCl or C2Cl6 compare favourably with those of untreated test bars. Sulphur treatment causes slight deterioration in mechanical properties. Fully grown nodules in both treated and untreated samples appear porous under SEM. Possible mechanisms of acceleration of graphitisation in the treated samples have been suggested.

Effect of Long-Period Stacking Order Phase and α-Mg Phase on Strength and Ductility of Mg-Zn-Y Alloy

2012 ◽  
Vol 706-709 ◽  
pp. 1237-1242 ◽  
Author(s):  
Masafumi Noda ◽  
Yoshihito Kawamura
Keyword(s):  
Mechanical Properties ◽  
Yield Strength ◽  
High Temperatures ◽  
Mg Alloys ◽  
Tensile Yield Strength ◽  
Block Type ◽  
Lpso Phase ◽  
Long Period ◽  
Stacking Order ◽  
Type Phase

Mg alloys are lightweight structural alloys that normally have a good castability and machinability as well as an excellent specific strength and rigidity. However, the mechanical properties of Mg alloys are inferior to those of Al alloys, and their range of industrial applications is limited. Recently, Mg–Zn–Y alloy has been found to show a high tensile yield strength with a good elongation. The alloy has a long-period stacking order (LPSO) phase as the secondary phase in an α-Mg phase. In general, the tensile yield strengths of LPSO-type Mg alloy are known to be markedly enhanced by the formation of kink bands in the LPSO phase and by microstructural refinement of the α-Mg phase during plastic deformation. The separate roles of the LPSO phase and the α-Mg phase in relation to the mechanical properties of high-strength LPSO-type Mg alloy were investigated at ambient and high temperatures. For high strengths at ambient and high temperatures, it was important that the α-Mg phase consisted of a fine-grain region and a nonrecrystallized region, and that the LPSO phase remained as a block-type phase. On the other hands, it was necessary to change the LPSO phase from a block-type phase into a plate-type phase by heat treatment before tensile testing to improve the ductility of the alloy while maintaining its tensile yield strength. Microstructural control of the LPSO phase and the α-Mg phase is necessary to obtained Mg–Zn–Y alloy with superior mechanical properties at ambient-to-high temperatures.

Mechanical And Superconducting Properties Of Cu-Nb3Sn In Situ Produced Composite Wires

1981 ◽  
Vol 12 ◽  
Author(s):  
A. Kolb-Telieps ◽  
B.L. Mordike ◽  
M. Mrowiec
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Yield Strength ◽  
Wide Temperature Range ◽  
Volume Fraction ◽  
Superconducting Properties ◽  
Temperature Range ◽  
Composite Wires ◽  
Strength And Ductility

ABSTRACTCu-Nb composite wires were produced from powder, electrolytically coated with tin and annealed to convert the Nb fibres to Nb 3Sn. The content was varied between 10 wt % and 40 wt %. The superconducting properties of the wires were determined. The mechanical properties, tensile strength, yield strength and ductility were measured as a function of volume fraction and deformation over a wide temperature range. The results are compared with those for wires produced by different techniques.

Sign in / Sign up

Export Citation Format

Share Document