scholarly journals Copper Surface Treatment Method with Antibacterial Performance Using “Super-Spread Wetting” Properties

Materials ◽  
2022 ◽  
Vol 15 (1) ◽  
pp. 392
Author(s):  
Beomdeok Seo ◽  
Hideyuki Kanematsu ◽  
Masashi Nakamoto ◽  
Yoshitsugu Miyabayashi ◽  
Toshihiro Tanaka
Keyword(s):  
Surface Roughness ◽  
Chemical Composition ◽  
Copper Ions ◽  
Steel Substrate ◽  
High Surface ◽  
Antibacterial Properties ◽  
Copper Ion ◽  
Copper Coating ◽  
Antibacterial Performance ◽  
Coated Surface

In this work, a copper coating is developed on a carbon steel substrate by exploiting the superwetting properties of liquid copper. We characterize the surface morphology, chemical composition, roughness, wettability, ability to release a copper ion from surfaces, and antibacterial efficacy (against Escherichia coli and Staphylococcus aureus). The coating shows a dense microstructure and good adhesion, with thicknesses of approximately 20–40 µm. X-ray diffraction (XRD) analysis reveals that the coated surface structure is composed of Cu, Cu2O, and CuO. The surface roughness and contact angle measurements suggest that the copper coating is rougher and more hydrophobic than the substrate. Inductively coupled plasma atomic emission spectroscopy (ICP-AES) measurements reveal a dissolution of copper ions in chloride-containing environments. The antibacterial test shows that the copper coating achieves a 99.99% reduction of E. coli and S. aureus. This study suggests that the characteristics of the copper-coated surface, including the chemical composition, high surface roughness, good wettability, and ability for copper ion release, may result in surfaces with antibacterial properties.

The Physical and Antibacterial Properties of Argentine-Doped TiO2 Film on Stainless Steel Substrate

2007 ◽  
Vol 280-283 ◽  
pp. 801-804 ◽  
Author(s):  
Xin Geng Ding ◽  
Li Li
Keyword(s):  
Stainless Steel ◽  
Tio2 Film ◽  
Steel Substrate ◽  
Sol Gel ◽  
Antibacterial Properties ◽  
Abrasive Resistance ◽  
Doped Tio2 ◽  
Tio2 Anatase ◽  
Antibacterial Performance ◽  
Surface Oxidization

The aim of the present study is to investigate the physical properties and antibacterial performances of Ag+-doped TiO2 film on stainless steel and effects of surface oxidization. In the experiment, the surface of stainless steel was been oxidized by heat treatment (550°C, 1 hour) before the Ag+-doped TiO2 (anatase) film being formed by sol-gel method. Sample A (filmed after surface oxidization), B (filmed without surface oxidization), C (only surface oxidization) and D (neither oxidized nor filmed) were respectively tested for corrosive resistance, abrasive resistance and adhesiveness, and the samples with different content of argentine was tested for antibacterial performance. Results: 1) Corrosion rates of sample A, B, C and D in 10% FeCl3 solution are respectively 1.65%, 1.87%, 2.02% and 3.28%, suggesting that the film has protected the stainless steel from the corrosion; 2) Scratching using a loaded (150 g) pin makes no crack on surface of sample A, while it results a slight scuffing on surface of sample B, suggesting that the surface oxidization has enhanced the abrasive resistance and adhesiveness of the TiO2 film, which may be due to the bridge-like function of the oxidation film; 3)Antibacterial performance is enhanced as the content of doping argentine increases, exceeding 90% when the argentine reached 3%, and the TiO2 film on the oxidized stainless steel performs better in antibacterial test than untreated one.

Medicinal Plants: Antibacterial Effects and Chemical Composition of Essential Oil of Foeniculum vulgare

2017 ◽  
Vol 8 (01) ◽  
Author(s):  
Azadeh Foroughi ◽  
Pouya Pournaghi ◽  
Fariba Najafi ◽  
Akram Zangeneh ◽  
Mohammad Mahdi Zangeneh ◽  
...  
Keyword(s):  
Chemical Composition ◽  
Medicinal Plants ◽  
Essential Oil ◽  
Antibacterial Properties ◽  
Screen Test ◽  
Antibacterial Activities ◽  
Gas Chromatography Mass Spectrometry ◽  
Resistant Bacteria ◽  
Antibacterial Effects ◽  
Foeniculum Vulgare

Medicinal plants are considered modern resources for producing agents that could act as alternatives to antibiotics in demeanor of antibiotic-resistant bacteria. The aim of the study was to evaluate the chemical composition and antibacterial activities of essential oil of Foeniculum vulgare (FV) against Pseudomonas aeruginosa and Bacillus subtilis. Gas chromatography mass spectrometry was done to specify chemical composion. As a screen test to detect antibacterial properties of the essential oil, agar disk and agar well diffusion methods were employed. Macrobroth tube test was performed to determinate MIC. The results indicated that the most substance found in FV essential oil was Trans-anethole (47.41 %), also the essential oil of FV with 0.007 g/ml concentration has prevented P. aeruginosa and with 0.002 g/ml concentration has prevented B. subtilis from the growth. Thus, the research represents the antibacterial effects of the medical herb on test P. aeruginosa and B. subtilis. We believe that the article provide support to the antibacterial properties of the essential oil. The results indicate the fact that the essential oil from the plant can be useful as medicinal or preservatives composition.

scholarly journals Investigation of Multiparameter Laser Stripping of AlTiN and DLC C Coatings

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 951
Author(s):  
Tomáš Primus ◽  
Josef Hlavinka ◽  
Pavel Zeman ◽  
Jan Brajer ◽  
Martin Šorm ◽  
...  
Keyword(s):  
Surface Roughness ◽  
High Efficiency ◽  
Steel Substrate ◽  
Cutting Tools ◽  
High Hardness ◽  
Working Time ◽  
Nanosecond Laser ◽  
Altin Coating ◽  
Successful Removal ◽  
Frequency Laser

The lifetime and properties of cutting tools and forming moulds can be prolonged and enhanced by the deposition of hard, thin coatings. After a certain period of usage, the coating will deteriorate. Any remaining coating must be removed prior to successful recoating. Laser stripping is a fast and environmentally friendly coating removal method. In this paper, we present laser removal of two types of coatings deposited on a 1.2379 tool steel substrate, namely, an AlTiN coating with high hardness and a DLC C coating with a small coefficient of friction (COF). A powerful nanosecond laser was employed to remove the coating from the substrate with high efficiency, along with suitable residual surface roughness. Measurements were taken of surface roughness, removed depth, and working time on a stripped area of 1 cm2. The samples were evaluated under a microscope, with a 3D profilometer, and by EDS chemical analysis. Successful removal of the coating was confirmed by optical analysis, but detailed chemical characterisation showed that about 30% of the coating element may remain on the surface. Moreover, a working time of less than 7.5 s per cm2 was obtained in this study. In addition, it was shown that the application of a second low energy, high frequency laser beam pass leads to remelting of the peaks of the material and reduced surface roughness.

scholarly journals Geometric correction for thermographic images of asteroid 162173 Ryugu by TIR (thermal infrared imager) onboard Hayabusa2

2021 ◽  
Vol 73 (1) ◽  
Author(s):  
Takehiko Arai ◽  
Tatsuaki Okada ◽  
Satoshi Tanaka ◽  
Tetsuya Fukuhara ◽  
Hirohide Demura ◽  
...  
Keyword(s):  
Surface Roughness ◽  
High Surface ◽  
Thermal Inertia ◽  
Thermal Infrared ◽  
Shape Model ◽  
Infrared Imager ◽  
Least Squares Fit ◽  
Temperature Maps ◽  
Pixel Scale ◽  
Thermal Infrared Imager

AbstractThe thermal infrared imager (TIR) onboard the Hayabusa2 spacecraft performed thermographic observations of the asteroid 162173 Ryugu (1999 JU$$_3$$ 3 ) from June 2018 to November 2019. Our previous reports revealed that the surface of Ryugu was globally filled with porous materials and had high surface roughness. These results were derived from making the observed temperature maps of TIR using a projection method onto the shape model of Ryugu as geometric corrections. The pointing directions of TIR were calculated using an interpolation of data from the SPICE kernels (NASA/NAIF) during the periods when the optical navigation camera (ONC) and the light detection and ranging (LIDAR) observations were performed. However, the mapping accuracy of the observed TIR images was degraded when the ONC and LIDAR were not performed with TIR. Also, the orbital and attitudinal fluctuations of Hayabusa2 increased the error of the temperature maps. In this paper, to solve the temperature image mapping problems, we improved the correction method by fitting all of the observed TIR images with the surface coordinate addressed on the high-definition shape model of Ryugu (SFM 800k v20180804). This correction adjusted the pointing direction of TIR by rotating the TIR frame relative to the Hayabusa2 frame using a least squares fit. As a result, the temperature maps spatially spreading areas were converged within high-resolved $$0.5^\circ$$ 0 . 5 ∘ by $$0.5^\circ$$ 0 . 5 ∘ maps. The estimated thermal inertia, for instance, was approximately 300$$\sim$$ ∼ 350 Jm$$^{-2}$$ - 2 s$$^{-0.5}$$ - 0.5 K$$^{-1}$$ - 1 at the hot area of the Ejima Saxum. This estimation was succeeded in case that the surface topographic features were larger than the pixel scale of TIR. However, the thermal inertia estimation of smooth terrains, such as the Urashima crater, was difficult because of surface roughness effects, where roughness was probably much smaller than the pixel scale of TIR.

scholarly journals Mechanical Characterization and Thermodynamic Analysis of Laser-Polished Landscape Design Products Using 3D Printing

Materials ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2601
Author(s):  
Yue Ba ◽  
Yu Wen ◽  
Shibin Wu
Keyword(s):  
Surface Roughness ◽  
3D Printing ◽  
Fused Deposition Modeling ◽  
High Surface ◽  
Landscape Design ◽  
Laser Polishing ◽  
Fused Deposition ◽  
Design Structure ◽  
3D Printed ◽  
Stability And Accuracy

Recent innovations in 3D printing technologies and processes have influenced how landscape products are designed, built, and developed. In landscape architecture, reduced-size models are 3D-printed to replicate full-size structures. However, high surface roughness usually occurs on the surfaces of such 3D-printed components, which requires additional post-treatment. In this work, we develop a new type of landscape design structure based on the fused deposition modeling (FDM) technique and present a laser polishing method for FDM-fabricated polylactic acid (PLA) mechanical components, whereby the surface roughness of the laser-polished surfaces is reduced from over Ra 15 µm to less than 0.25 µm. The detailed results of thermodynamics and microstructure evolution are further analyzed during laser polishing. The stability and accuracy of the results are evaluated based on the standard deviation. Additionally, the superior tensile and flexural properties are examined in the laser-polished layer, in which the ultimate tensile strength (UTS) is increased by up to 46.6% and the flexural strength is increased by up to 74.5% compared with the as-fabricated components. Finally, a real polished landscape model is simulated and optimized using a series of scales.

scholarly journals Effect of Optical and Morphological Control of Single-Structured LEC Device

Micromachines ◽  
2021 ◽  
Vol 12 (7) ◽  
pp. 843
Author(s):  
Woo Jin Jeong ◽  
Jong Ik Lee ◽  
Hee Jung Kwak ◽  
Jae Min Jeon ◽  
Dong Yeol Shin ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Surface Roughness ◽  
Surface Properties ◽  
High Efficiency ◽  
High Surface ◽  
Reduction Rate ◽  
Operating Characteristics ◽  
Emission Layer ◽  
Light Emitting ◽  
Stable Operating

We investigated the performance of single-structured light-emitting electrochemical cell (LEC) devices with Ru(bpy)3(PF6)2 polymer composite as an emission layer by controlling thickness and heat treatment. When the thickness was smaller than 120–150 nm, the device performance decreased because of the low optical properties and non-dense surface properties. On the other hand, when the thickness was over than 150 nm, the device had too high surface roughness, resulting in high-efficiency roll-off and poor device stability. With 150 nm thickness, the absorbance increased, and the surface roughness was low and dense, resulting in increased device characteristics and better stability. The heat treatment effect further improved the surface properties, thus improving the device characteristics. In particular, the external quantum efficiency (EQE) reduction rate was shallow at 100 °C, which indicates that the LEC device has stable operating characteristics. The LEC device exhibited a maximum luminance of 3532 cd/m2 and an EQE of 1.14% under 150 nm thickness and 100 °C heat treatment.

scholarly journals An Investigation on Design and Characterization of a Highly Selective LED Optical Sensor for Copper Ions in Aqueous Solutions

Sensors ◽  
2021 ◽  
Vol 21 (4) ◽  
pp. 1099
Author(s):  
Sheng-Chun Hung ◽  
Chih-Cheng Lu ◽  
Yu-Ting Wu
Keyword(s):  
Aqueous Solutions ◽  
Metal Ions ◽  
Copper Ions ◽  
Incident Light ◽  
Copper Ion ◽  
Intensity Change ◽  
Optical Absorbance ◽  
Sensing System ◽  
Optic Sensor ◽  
Cu Ions

The optical characteristics of copper ion detection, such as the photometric absorbance of specific wavelengths, exhibit significant intensity change upon incident light into the aqueous solutions with different concentrations of metal ions due to the electron transition in the orbit. In this study, we developed a low-cost, small-size and fast-response photoelectric sensing prototype as an optic sensor for copper (Cu) ions detection by utilizing the principle of optical absorption. We quantified the change of optical absorbance from infra-red (IR) light emitting diodes (LEDs) upon different concentrations of copper ions and the transmitted optical signals were transferred to the corresponding output voltage through a phototransistor and circuit integrated in the photoelectric sensing system. The optic sensor for copper (Cu) ions demonstrated not only excellent specificity with other metal ions such as cadmium (Cd), nickel (Ni), iron (Fe) and chloride (Cl) ions in the same aqueous solution but also satisfactory linearity and reproducibility. The sensitivity of the preliminary sensing system for copper ions was 29 mV/ppm from 0 to 1000 ppm. In addition, significant ion-selective characteristics and anti-interference capability were also observed in the experiments by the proposed approach.

scholarly journals Green Synthesis and Incorporation of Sericin Silver Nanoclusters into Electrospun Ultrafine Cellulose Acetate Fibers for Anti-Bacterial Applications

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1411
Author(s):  
Mujahid Mehdi ◽  
Huihui Qiu ◽  
Bing Dai ◽  
Raja Fahad Qureshi ◽  
Sadam Hussain ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Green Synthesis ◽  
Cellulose Acetate ◽  
Antibacterial Properties ◽  
Vital Role ◽  
Silver Nanoclusters ◽  
Composite Fibers ◽  
E Coli ◽  
Antibacterial Performance ◽  
Field Emission Electron Microscopy

Fiber based antibacterial materials have gained an enormous attraction for the researchers in these days. In this study, a novel Sericin Encapsulated Silver Nanoclusters (sericin-AgNCs) were synthesized through single pot and green synthesis route. Subsequently these sericin-AgNCs were incorporated into ultrafine electrospun cellulose acetate (CA) fibers for assessing the antibacterial performance. The physicochemical properties of sericin-AgNCs/CA composite fibers were investigated by transmission electron microscopy (TEM), field emission electron microscopy (FE-SEM), Fourier transform infrared spectroscopy (FTIR) and wide X-ray diffraction (XRD). The antibacterial properties of sericin-AgNCs/CA composite fibers against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) were systematically evaluated. The results showed that sericin-AgNCs incorporated in ultrafine CA fibers have played a vital role for antibacterial activity. An amount of 0.17 mg/mL sericin-AgNCs to CA fibers showed more than 90% results and elevated upto >99.9% with 1.7 mg/mL of sericin-AgNCs against E. coli. The study indicated that sericin-AgNCs/CA composite confirms an enhanced antibacterial efficiency, which could be used as a promising antibacterial product.

Comparison of Focused Ion Beam and Conventional Techniques on Tem Specimen Preparation of Metal-Ceramic Interfaces

1998 ◽  
Vol 4 (S2) ◽  
pp. 860-861 ◽  
Author(s):  
A. Ramirez de Arellano López ◽  
W.-A. Chiou ◽  
K. T. Faber
Keyword(s):  
Focused Ion Beam ◽  
Ceramic Coating ◽  
Steel Substrate ◽  
Ion Beam ◽  
Specimen Preparation ◽  
Inhomogeneous Materials ◽  
Cross Sectional ◽  
Fine Grain ◽  
Basic Industry ◽  
Coated Surface

The results of TEM analyses of materials are critically dependent on the quality of the sample prepared. Although numerous techniques have been developed in the last two decades, differential thinning of inhomogeneous materials remains a serious problem. Recently, focused ion beam (FIB) technique has been introduced for cross-sectional sample preparation for TEM and SEM.A novel system for depositing a fine-grain (∼ 200 nm) ceramic coating on a metal surface via a patent pending Small-Particle Plasma Spray (SPPS) technique has been developed at the Basic Industry Research Laboratory of Northwestern University. To understand the properties of the coated surface, the ceramic/metal interface and the microstructure of the ceramic coating must be investigated. This paper presents a comparison of the microstructure of an A12O3 coating on a mild steel substrate prepared using conventional and FEB techniques.

scholarly journals Post-Processing and Surface Characterization of Additively Manufactured Stainless Steel 316L Lattice: Implications for BioMedical Use

Materials ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1376
Author(s):  
Alex Quok An Teo ◽  
Lina Yan ◽  
Akshay Chaudhari ◽  
Gavin Kane O’Neill
Keyword(s):  
Surface Roughness ◽  
Stainless Steel ◽  
Surface Characterization ◽  
High Surface ◽  
Surface Characteristics ◽  
Post Processing ◽  
Stainless Steel 316L ◽  
Processing Methods ◽  
Particulate Debris

Additive manufacturing of stainless steel is becoming increasingly accessible, allowing for the customisation of structure and surface characteristics; there is little guidance for the post-processing of these metals. We carried out this study to ascertain the effects of various combinations of post-processing methods on the surface of an additively manufactured stainless steel 316L lattice. We also characterized the nature of residual surface particles found after these processes via energy-dispersive X-ray spectroscopy. Finally, we measured the surface roughness of the post-processing lattices via digital microscopy. The native lattices had a predictably high surface roughness from partially molten particles. Sandblasting effectively removed this but damaged the surface, introducing a peel-off layer, as well as leaving surface residue from the glass beads used. The addition of either abrasive polishing or electropolishing removed the peel-off layer but introduced other surface deficiencies making it more susceptible to corrosion. Finally, when electropolishing was performed after the above processes, there was a significant reduction in residual surface particles. The constitution of the particulate debris as well as the lattice surface roughness following each post-processing method varied, with potential implications for clinical use. The work provides a good base for future development of post-processing methods for additively manufactured stainless steel.

Sign in / Sign up

Export Citation Format

Share Document