scholarly journals The Significance of Optimizing Mn-Content in Tuning the Microstructure and Mechanical Properties of δ-TRIP Steels

Metals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 523
Author(s):  
Baoyu Xu ◽  
Peng Chen ◽  
Zhengxian Li ◽  
Di Wu ◽  
Guodong Wang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Work Hardening ◽  
Large Fraction ◽  
High Strength ◽  
Tensile Tests ◽  
Continuous Annealing ◽  
Electron Backscattered Diffraction ◽  
Trip Steels ◽  
Mn Content ◽  
Mn Steel

The δ-TRIP steel has attracted a lot of attention for its potential application in automotive components, owing to the low density, good combination of strength, and ductility. As the difficulty in yield strength further increasement is caused by large fraction ferrite, the work hardening ability was enhanced by optimizing the manganese (Mn)-content in this study. Three δ-TRIP steels with different manganese (Mn)-content were designed to explore the significant effect of Mn content on the work hardening behavior in order to develop high strength steel suitable for the industrial continuous annealing process. The detailed effect of Mn on microstructure evolution and deformation behavior was studied by scanning electron microscope (SEM), interrupted tensile tests, X-ray diffraction (XRD), and in-situ electron backscattered diffraction (EBSD). The study suggested that 2 Mn steel has the lowest degree of bainitic transformation, as a result of fine grain size of prior austenite. The large TRIP effect and dislocation strengthening improve the work hardening rate, resulting in 2 Mn steel exhibiting comparable mechanical properties with the QP980 steels. The retained austenite in 1.5 Mn steel progressively transformed into martensite and sustained the strain to a high strain value of 0.40, showing a good strength-ductility balance.

Investigations on the Mechanical Properties and Formability of Friction Stir Welded Tailored Blanks

2007 ◽  
Vol 344 ◽  
pp. 143-150 ◽  
Author(s):  
Gianluca Buffa ◽  
Livan Fratini ◽  
Marion Merklein ◽  
Detlev Staud
Keyword(s):  
Mechanical Properties ◽  
Stress Condition ◽  
Research Effort ◽  
High Strength Steels ◽  
High Strength ◽  
Tensile Tests ◽  
Friction Stir ◽  
Tailored Blanks ◽  
Sheet Stamping ◽  
Wide Range

Tight competition characterizing automotive industries in the last decades has determined a strong research effort aimed to improve utilized processes and materials in sheet stamping. As far as the latter are regarded light weight alloys, high strength steels and tailored blanks have been increasingly utilized with the aim to reduce parts weight and fuel consumptions. In the paper the mechanical properties and formability of tailored welded blanks made of a precipitation hardenable aluminum alloy but with different sheet thicknesses, have been investigated: both laser welding and friction stir welding have been developed to obtain the tailored blanks. For both welding operations a wide range of the thickness ratios has been considered. The formability of the obtained blanks has been characterized through tensile tests and cup deep drawing tests, in order to show the formability in dependency of the stress condition; what is more mechanical and metallurgical investigations have been made on the welded joints.

scholarly journals Experimental Investigation into Corrosion Effect on Mechanical Properties of High Strength Steel Bars under Dynamic Loadings

2018 ◽  
Vol 2018 ◽  
pp. 1-12 ◽  
Author(s):  
Hui Chen ◽  
Jinjin Zhang ◽  
Jin Yang ◽  
Feilong Ye
Keyword(s):  
Mechanical Properties ◽  
Strain Rate ◽  
Dynamic Loading ◽  
High Strength Steel ◽  
High Strength ◽  
Tensile Tests ◽  
Reinforcing Steel ◽  
Test Results ◽  
Cross Sectional ◽  
Steel Bars

The tensile behaviors of corroded steel bars are important in the capacity evaluation of corroded reinforced concrete structures. The present paper studies the mechanical behavior of the corroded high strength reinforcing steel bars under static and dynamic loading. High strength reinforcing steel bars were corroded by using accelerated corrosion methods and the tensile tests were carried out under different strain rates. The results showed that the mechanical properties of corroded high strength steel bars were strain rate dependent, and the strain rate effect decreased with the increase of corrosion degree. The decreased nominal yield and ultimate strengths were mainly caused by the reduction of cross-sectional areas, and the decreased ultimate deformation and the shortened yield plateau resulted from the intensified stress concentration at the nonuniform reduction. Based on the test results, reduction factors were proposed to relate the tensile behaviors with the corrosion degree and strain rate for corroded bars. A modified Johnson-Cook strength model of corroded high strength steel bars under dynamic loading was proposed by taking into account the influence of corrosion degree. Comparison between the model and test results showed that proposed model properly describes the dynamic response of the corroded high strength rebars.

Correlation among Microstructure, Texture, and Properties along the Thickness Direction in As-Hot-Rolled and As-Solution-Quenched Al7055 Thick Plates

2021 ◽  
Vol 1026 ◽  
pp. 65-73
Author(s):  
Kai Zhu ◽  
Hong Wei Yan
Keyword(s):  
Mechanical Properties ◽  
Yield Strength ◽  
Tensile Tests ◽  
Rolled Plate ◽  
Uniaxial Tensile ◽  
Thickness Direction ◽  
Electron Backscattered Diffraction ◽  
Thick Plates ◽  
Aluminum Plates ◽  
Hot Rolled

Both microstructure inhomogeneity and mechanical property diversity along the thickness direction in rolled thick aluminum plates have been considered to have a remarkable impact on the performance and properties of the products made from the plates. In this study, scanning electron microscopy (SEM) and electron backscattered diffraction (EBSD) characterizations of microstructure and texture types along the thickness directions of Al7055 thick plate specimens prepared using two conditions, hot-rolling and solution-quenching, were performed. To examine the mechanical properties, uniaxial tensile tests were also carried out on specimens machined from both types of thick plates, using a layered strategy along the thickness direction. The results indicate that both the microstructure and mechanical properties are inhomogeneous under the two conditions. Furthermore, it is evident that there is a hereditary relationship between the mechanical properties of the two plates—areas with higher yield strength in the as-hot-rolled plate correspond to areas with the higher yield strength in the as-solution-quenched plate

scholarly journals Changing in Fatigue Life of 300 M Bainitic Steel After Laser Carburizing and Plasma Nitriding

2018 ◽  
Vol 165 ◽  
pp. 21002 ◽  
Author(s):  
Antonio J. Abdalla ◽  
Douglas Santos ◽  
Getúlio Vasconcelos ◽  
Vladimir H. Baggio-Scheid ◽  
Deivid F. Silva
Keyword(s):  
Mechanical Properties ◽  
Fatigue Life ◽  
Plasma Nitriding ◽  
Fatigue Behavior ◽  
High Strength ◽  
Tensile Tests ◽  
Steel Sample ◽  
Fatigue Tests ◽  
300M Steel ◽  
Structural Applications

In this work 300M steel samples is used. This high-strength steel is used in aeronautic and aerospace industry and other structural applications. Initially the 300 M steel sample was submitted to a heat treatment to obtain a bainític structure. It was heated at 850 °C for 30 minutes and after that, cooled at 300 °C for 60 minutes. Afterwards two types of surface treatments have been employed: (a) using low-power laser CO2 (125 W) for introducing carbon into the surface and (b) plasma nitriding at a temperature of 500° C for 3 hours. After surface treatment, the metallographic preparation was carried out and the observations with optical and electronic microscopy have been made. The analysis of the coating showed an increase in the hardness of layer formed on the surface, mainly, among the nitriding layers. The mechanical properties were analyzed using tensile and fatigue tests. The results showed that the mechanical properties in tensile tests were strongly affected by the bainitic microstructure. The steel that received the nitriding surface by plasma treatment showed better fatigue behavior. The results are very promising because the layer formed on steel surface, in addition to improving the fatigue life, still improves protection against corrosion and wear.

Influence of Continuous Annealing Conditions on the Microstructure and Mechanical Properties of a C-Mn Dual Phase Steel

2010 ◽  
Vol 638-642 ◽  
pp. 3479-3484 ◽  
Author(s):  
Roberta O. Rocha ◽  
Tulio M.F. Melo ◽  
Dagoberto Brandao Santos
Keyword(s):  
Mechanical Properties ◽  
Microstructural Analysis ◽  
Tensile Tests ◽  
Recrystallization Temperature ◽  
Continuous Annealing ◽  
Dual Phase ◽  
Heating Rates ◽  
Microstructure And Mechanical Properties ◽  
Annealing Cycle ◽  
Soaking Temperature

The influence of continuous annealing variables on the microstructure and mechanical properties of a C-Mn Dual Phase (DP) steel was studied. The annealing cycles were simulated using a Gleeble machine. Some specimens were quenched at different stages of the annealing cycle in order to evaluate the microstructural evolution during the annealing process. Tensile tests and microstrutural analysis were carried out. The results showed that high heating rates increased the final recrystallization temperature and as a consequence the microstructure obtained was refined. Austenite grain nucleation and growth were also influenced by the heating rates. Soaking temperature was the most influent variable on the mechanical properties, i. e., the yield strength increased and the tensile strength decreased with an increase in the soaking temperature. Microstructural analysis showed that not only martensite, but also bainite and martensite-retained autenite constituent (MA) were formed. Undissolved carbides were also detected by transmission electron microscopy.

Tensile properties of the FFF-processed thermoplastic polyurethane (TPU) elastomer

2021 ◽  
Author(s):  
Budi Arifvianto ◽  
Teguh Nur Iman ◽  
Benidiktus Tulung Prayoga ◽  
Rini Dharmastiti ◽  
Urip Agus Salim ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Low Cost ◽  
Thermoplastic Polyurethane ◽  
High Strength ◽  
Tensile Tests ◽  
Uniaxial Tensile ◽  
Fused Filament Fabrication ◽  
Raster Angle ◽  
Manufacturing Techniques

Abstract Fused filament fabrication (FFF) has become one of the most popular, practical, and low-cost additive manufacturing techniques for fabricating geometrically-complex thermoplastic polyurethane (TPU) elastomer. However, there are still some uncertainties concerning the relationship between several operating parameters applied in this technique and the mechanical properties of the processed material. In this research, the influences of extruder temperature and raster orientation on the mechanical properties of the FFF-processed TPU elastomer were studied. A series of uniaxial tensile tests was carried out to determine tensile strength, strain, and elastic modulus of TPU elastomer that had been printed with various extruder temperatures, i.e., 190–230 °C, and raster angles, i.e., 0–90°. Thermal and chemical characterizations were also conducted to support the analysis in this research. The results obviously showed the ductile and elastic characteristics of the FFF-processed TPU, with specific tensile strength and strain that could reach up to 39 MPa and 600%, respectively. The failure mechanisms operating on the FFF-processed TPU and the result of stress analysis by using the developed Mohr’s circle are also discussed in this paper. In conclusion, the extrusion temperature of 200 °C and raster angle of 0° could be preferred to be applied in the FFF process to achieve high strength and ductile TPU elastomer.

Effect of Quenching and Partitioning Processing on Microstructure and Mechanical Properties of a Low Alloyed Steel

2018 ◽  
Vol 941 ◽  
pp. 52-57
Author(s):  
Bernd Pfleger ◽  
Marina Gruber ◽  
Gerald Ressel ◽  
Peter Gruber ◽  
Matthew Galler ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Strength ◽  
Phase Evolution ◽  
Tensile Tests ◽  
Austenite Phase ◽  
Phase Fraction ◽  
Quenching Temperature ◽  
Quenching And Partitioning ◽  
Low Alloyed Steel ◽  
A Minor

The concept of quenching and partitioning (Q&P) is a tool to generate steels with high strength and high ductility resulting from a relatively high amount of martensite and austenite. As the parameters of the Q&P treatment influence the strength and ductility properties, the goal of this work was to analyze the effects of varying quenching and partitioning temperatures on the phase evolution, on the retained austenite phase fraction and on the mechanical properties. The phase evolution during heat treatment was analyzed by dilatometer and the microstructure after processing was characterized by light microscopy in combination with color etching according to Klemm. The austenite phase fraction and its carbon content were determined by X-Ray diffraction and the mechanical properties were evaluated by tensile tests. It is shown that the quenching temperature has a minor impact on the phase fraction of austenite as well as its stabilization by carbon and thus, also the mechanical properties. Furthermore, austenite transformation during the partitioning treatment is illustrated.

scholarly journals Effect of Intercritical Annealing and Austempering on the Microstructure and Mechanical Properties of a High Silicon Manganese Steel

Metals ◽  
2020 ◽  
Vol 10 (11) ◽  
pp. 1448 ◽  
Author(s):  
Mattia Franceschi ◽  
Luca Pezzato ◽  
Claudio Gennari ◽  
Alberto Fabrizi ◽  
Marina Polyakova ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Intercritical Annealing ◽  
High Strength ◽  
Xrd Analysis ◽  
Tensile Tests ◽  
Manganese Steel ◽  
Microstructure And Mechanical Properties ◽  
Martensitic Microstructure ◽  
Steel Grades ◽  
High Silicon

High Silicon Austempered steels (AHSS) are materials of great interest due to their excellent combination of high strength, ductility, toughness, and limited costs. These steel grades are characterized by a microstructure consisting of ferrite and bainite, accompanied by a high quantity retained austenite (RA). The aim of this study is to analyze the effect of an innovative heat treatment, consisting of intercritical annealing at 780 °C and austempering at 400 °C for 30 min, on the microstructure and mechanical properties of a novel high silicon steel (0.43C-3.26Si-2.72Mn wt.%). The microstructure was characterized by optical and electron microscopy and XRD analysis. Hardness and tensile tests were performed. A multiphase ferritic-martensitic microstructure was obtained. A hardness of 426 HV and a tensile strength of 1650 MPa were measured, with an elongation of 4.5%. The results were compared with those ones obtained with annealing and Q&T treatments.

scholarly journals Effect of Retained Austenite and Non-Metallic Inclusions on the Mechanical Properties of Resistance Spot Welding Nuggets of Low-Alloy TRIP Steels

Metals ◽  
2019 ◽  
Vol 9 (10) ◽  
pp. 1064 ◽  
Author(s):  
Víctor H. Vargas Cortés ◽  
Gerardo Altamirano Guerrero ◽  
Ignacio Mejía Granados ◽  
Víctor H. Baltazar Hernández ◽  
Cuauhtémoc Maldonado Zepeda
Keyword(s):  
Mechanical Properties ◽  
Tensile Test ◽  
Retained Austenite ◽  
High Strength ◽  
Microstructural Characterization ◽  
Spot Welds ◽  
Trip Steels ◽  
Resistance Spot ◽  
Lap Shear ◽  
Metallic Inclusions

The combination of high strength and formability of transformation induced plasticity (TRIP) steels is interesting for the automotive industry. However, the poor weldability limits its industrial application. This paper shows the results of six low-alloy TRIP steels with different chemical composition which were studied in order to correlate retained austenite (RA) and non-metallic inclusions (NMI) with their resistance spot welded zones to their joints’ final mechanical properties. RA volume fractions were quantified by X-ray microdiffraction (µSXRD) while the magnetic saturation technique was used to quantify NMI contents. Microstructural characterization and NMI of the base metals and spot welds were assessed using scanning electron microscopy (SEM). Weld nuggets macrostructures were identified using optical microscopy (OM). The lap-shear tensile test was used to determine the final mechanical properties of the welded joints. It was found that NMI content in the fusion zone (FZ) was higher than those in the base metal and heat affected zone (HAZ). Whereas, traces of RA were found in the HAZ of highly alloyed TRIP steels. Lap-shear tensile test results showed that mechanical properties of spot welds were affected by NMI contents, but in a major way by the decomposition of RA in the FZ and HAZ.

Sign in / Sign up

Export Citation Format

Share Document