scholarly journals Activated Carbon-Spinels Composites for Waste Water Treatment

Metals ◽  
2018 ◽  
Vol 8 (12) ◽  
pp. 1070
Author(s):  
Ernesto de la Torre ◽  
Ana Lozada ◽  
Maricarmen Adatty ◽  
Sebastián Gámez
Keyword(s):  
Activated Carbon ◽  
Active Carbon ◽  
Waste Water Treatment ◽  
Copper Nitrate ◽  
Cobalt Nitrate ◽  
Precipitation Method ◽  
Molar Ratio ◽  
Copper Ferrite ◽  
Cyanide Oxidation ◽  
Two Phases

Nowadays, mining effluents have several contaminants that produce great damage to the environment, cyanide chief among them. Ferrites synthesized from transition metals have oxidative properties that can be used for cyanide oxidation due to their low solubility. In this study, cobalt and copper ferrites were synthesized via the precipitation method, using cobalt nitrate, copper nitrate, and iron nitrate as precursors in a molar ratio of Co or Cu:Fe = 1:2 and NaOH as the precipitating agent. The synthesized ferrites were impregnated in specific areas on active carbon. These composites were characterized using X-Ray Diffraction (XRD) and Scanning Electron Spectroscopy (SEM). The XRD results revealed a cubic spinel structure of ferrites with a single phase of cobalt ferrite and two phases (copper ferrite and copper oxides) for copper. The CoFe2O4 impregnated on active carbon reached a cyanide oxidation of 98% after 8 h of agitation; the composite could be recycled five times with an 18% decrease in the catalytic activity. In cobalt ferrites, a greater dissolution of iron than cobalt was obtained. In the case of copper ferrite, however, the copper dissolution was higher. These results confirm that ferrites and activated carbon composites are a novel alternative for cyanide treatment in mining effluents.

scholarly journals The influence of active carbon contaminants on the ozonation mechanism interpretation

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Lilla Fijołek ◽  
Joanna Świetlik ◽  
Marcin Frankowski
Keyword(s):  
Activated Carbon ◽  
Active Carbon ◽  
Alkali Metals ◽  
Activated Carbons ◽  
Carbon Surface ◽  
Bulk Solution ◽  
Ozone Decomposition ◽  
Reaction Products ◽  
Treatment Technology ◽  
Carbon Impurities

AbstractIn water treatment technology, activated carbons are used primarily as sorbents to remove organic impurities, mainly natural organic matter, but also as catalysts in the ozonation process. Commercially available activated carbons are usually contaminated with mineral substances, classified into two main groups: alkali metals (Ca, Na, K, Li, Mg) and multivalent metals (Al, Fe, Ti, Si). The presence of impurities on the carbon surface significantly affects the pHpzc values determined for raw and ozonated carbon as well as their acidity and alkalinity. The scale of the observed changes strongly depends on the pH of the ozonated system, which is related to the diffusion of impurities from the carbon to the solution. In an acidic environment (pH 2.5 in this work), the ozone molecule is relatively stable, yet active carbon causes its decomposition. This is the first report that indirectly indicates that contaminants on the surface of activated carbon (multivalent elements) contribute to the breakdown of ozone towards radicals, while the process of ozone decomposition by purified carbons does not follow the radical path in bulk solution. Carbon impurities also change the distribution of the reaction products formed by organic pollutants ozonation, which additionally confirms the radical process. The study showed that the use of unpurified activated carbon in the ozonation of succinic acid (SA) leads to the formation of a relatively large amount of oxalic acid (OA), which is a product of radical SA degradation. On the other hand, in solutions with purified carbon, the amount of OA generated is negligible.

A novel separation method of the valuable components for activated clay production wastewater

2021 ◽  
Vol 19 (1) ◽  
pp. 530-540
Author(s):  
Lvshan Zhou ◽  
Tongjiang Peng ◽  
Hongjuan Sun ◽  
Dong Fu ◽  
Chuan Lai
Keyword(s):  
Aluminum Phosphate ◽  
Iron Phosphate ◽  
Acid Sites ◽  
Precipitation Method ◽  
Molar Ratio ◽  
Precipitation Process ◽  
Iron Aluminum ◽  
Phosphorus Iron ◽  
Optimized Conditions ◽  
Acidic Wastewater

Abstract The acidic wastewater produced by the wet production of activated clay contains valuable components such as iron and aluminum. The precipitation method was successfully introduced to separate iron and aluminum from the activated clay production wastewater step by step, which can not only recover the valuable components, but also avoid environmental pollution. In the separation process, gypsum, iron aluminum phosphate, alumina, and sodium sulfate were prepared, and the phase compositions of separation products were analyzed by XRD and IR. The main influencing factors in the separation of iron and aluminum components were studied by single factor experiment. The results show that at the optimized conditions, phosphorus/iron molar ratio 6.0, the system pH 3.0, the reaction temperature 343 K, and the reaction time 90 min, the iron(iii) ion in the system can form a sodium-containing aluminum iron phosphate double salt, and the filtrate after separating Fe3+ and part of Al3+ can meet the requirements for forming high-purity Al2O3. During the phosphate precipitation process, the hypothesis should be correct that Al3+ reacts with PO 4 3 − {\text{PO}}_{4}^{3-} to form an AlPO4 skeleton, Fe3+ isomorphically replaces Al3+ in the [AlO4] tetrahedron, and adsorption occurs simultaneously, with Na+ occupying the terminal acid sites, P(Al)–OH.

Effect of Fe and Co promoters on CO methanation activity of nickel catalyst prepared by impregnation – co-precipitation method

2020 ◽  
Vol 18 (5-6) ◽  
Author(s):  
Buyan-Ulzii Battulga ◽  
Tungalagtamir Bold ◽  
Enkhsaruul Byambajav
Keyword(s):  
Synergetic Effect ◽  
Space Velocity ◽  
Catalytic Performance ◽  
Precipitation Method ◽  
Molar Ratio ◽  
Alumina Support ◽  
Co Methanation ◽  
Temperature Range ◽  
Co Precipitation ◽  
Catalyst Distribution

AbstractNi based catalysts supported on γ-Al2O3 that was unpromoted (Ni/γAl2O3) or promoted (Ni–Fe/γAl2O3, Ni–Co/γAl2O3, and Ni–Fe–Co/γAl2O3) were prepared using by the impregnation – co-precipitation method. Their catalytic performances for CO methanation were studied at 3 atm with a weight hourly space velocity (WHSV) of 3000 ml/g/h of syngas with a molar ratio of H2/CO = 3 and in the temperature range between 130 and 350 °C. All promoters could improve nickel distribution, and decreased its particle sizes. It was found that the Ni–Co/γAl2O3 catalyst showed the highest catalytic performance for CO methanation in a low temperature range (<250 °C). The temperatures for the 20% CO conversion over Ni–Co/γAl2O3, Ni–Fe/γAl2O3, Ni–Fe–Co/γAl2O3 and Ni/γAl2O3 catalysts were 205, 253, 263 and 270 °C, respectively. The improved catalyst distribution by the addition of cobalt promoter caused the formation of β type nickel species which had an appropriate interacting strength with alumina support in the Ni–Co/γAl2O3. Though an addition of iron promoter improved catalyst distribution, the methane selectivity was lowered due to acceleration of both CO methanation and WGS reaction with the Ni–Fe/γAl2O3. Moreover, it was found that there was no synergetic effect from the binary Fe–Co promotors in the Ni–Fe–Co/γAl2O3 on catalytic activity for CO methanation.

Positive effects of a halloysite-supported Cu/Co catalyst fabricated by a urea-driven deposition precipitation method on the CO-SCR reaction and SO2 poisoning

2021 ◽  
Author(s):  
Wei-Jing Li ◽  
Shu Tsai ◽  
Ming-Yen Wey
Keyword(s):  
Co Oxidation ◽  
Catalytic Reduction ◽  
Precipitation Method ◽  
Molar Ratio ◽  
Halloysite Nanotube ◽  
Co Catalyst ◽  
Reduction Of No ◽  
Co Catalysts ◽  
Positive Effects ◽  
So2 Poisoning

Cu/Co catalysts were prepared on halloysite nanotube supports by a urea-driven deposition-precipitation method for CO oxidation and the selective catalytic reduction of NO (CO-SCR). First, the Cu/NH3 molar ratio was...

scholarly journals Micropollutant-loaded powdered activated carbon released from waste water treatment plants: a risk for sediment-dwelling organisms?

2021 ◽  
Vol 33 (1) ◽  
Author(s):  
Marion Woermann ◽  
Julios Armand Kontchou ◽  
Bernd Sures
Keyword(s):  
Activated Carbon ◽  
Wastewater Treatment Plants ◽  
Water Cycle ◽  
Waste Water Treatment ◽  
Additional Treatment ◽  
Powdered Activated Carbon ◽  
Lumbriculus Variegatus ◽  
Negative Effects ◽  
Global Water Cycle ◽  
Receiving Waters

Abstract Background In order to protect aquatic environments and to reduce the presence of micropollutants in the global water cycle, wastewater treatment plants (WWTPs) often implement an additional treatment step. One of the most effective measures is the use of powdered activated carbon (PAC) as an adsorbent for micropollutants. This method provides sufficient elimination rates for several micropollutants and has been successfully employed in many WWTPs. Despite this success, there might be a drawback as the retention of the PAC in the WWTP can be challenging and losses of micropollutant-loaded PAC into the aquatic environment may occur. Upon emission, micropollutant-loaded PAC is expected to settle to the benthic zone of receiving waters, where sediment-dwelling organisms may ingest these particles. Therefore, the present study investigated possible adverse effects of micropollutant-loaded PAC from a WWTP as compared to unloaded (native) and diclofenac-loaded PAC on the sediment-dwelling annelid Lumbriculus variegatus. Results Native PAC induced the strongest effects on growth (measured as biomass) and reproduction of the annelids. The corresponding medium effective concentrations (EC50) were 1.7 g/kg and 1.8 g/kg, respectively. Diclofenac-loaded PAC showed lower effects with an EC50 of 2.5 g/kg for growth and EC50 of 3.0 g/kg for reproduction. Although tested at the same concentrations, the micropollutant-loaded PAC from the WWTP did not lead to obvious negative effects on the endpoints investigated for L.variegatus and only a slight trend of a reduced growth was detected. Conclusion We did not detect harmful effects on L. variegatus caused by the presence of MP-loaded PAC from a WWTP which gives an auspicious perspective for PAC as an advanced treatment option.

Treatment of Dyeing and Printing Wastewater by Copper Oxide Loaded on Coconut Shell Activated Carbon

2011 ◽  
Vol 366 ◽  
pp. 412-415
Author(s):  
Yu De Liu ◽  
Bo Quan Jiang ◽  
Zheng Qiang Xiao
Keyword(s):  
Activated Carbon ◽  
Copper Oxide ◽  
Orthogonal Experiment ◽  
Chemical Activation ◽  
Copper Nitrate ◽  
Color Removal ◽  
Removal Rates ◽  
Activation Temperature ◽  
Coconut Shells ◽  
Coconut Shell Activated Carbon

The activated carbon loaded copper oxide catalyst was prepared from Hainan abandoned coconut shells using chemical activation method and applied in treatment of acid bright red GR simulation dyeing wastewater. The effects of phosphoric acid concentration, ratio of liquid to solid, activation time and activation temperature on the COD and color removal rates were investigated by orthogonal experiment. The results showed that the optimal values of the parameters above were 65% (in mass), 3:1, 2.5h and 500°C under the designed copper oxide loading conditions of calcining temperature 300°C,calcining time 3.0 h and use level of copper nitrate 15 mL. Using the prepared sample for the treatment of the wastewater, the COD and color removal rates reached 94.384% and 99.840%, respectively.

Characterization of Biomaterial and Tissue Response Analysis after Implantation

2018 ◽  
Vol 930 ◽  
pp. 48-52
Author(s):  
Eliana dos Santos Câmara-Pereira ◽  
Ana Emília Holanda Rolim ◽  
Isabela Cerqueira Barreto ◽  
Laise Monteiro Campos Moraes ◽  
Lilian Campos ◽  
...  
Keyword(s):  
Repair Process ◽  
Tissue Response ◽  
Precipitation Method ◽  
Molar Ratio ◽  
Osteogenic Potential ◽  
Response Analysis ◽  
Defect Site ◽  
Critical Defect ◽  
Defect Repair

Some biomaterials can be used to promote tissue repair process. The biological substitutes (biomaterials such as hydroxyapatite beads) can be used with some advantages and purpose of mimicking responses to on-site repair of the injured bone. The objective of this study was to evaluate the osteogenic potential of the biomaterial composed of hydroxyapatite and alginate in place of the critical defect. bioceramic samples stoichiometric hydroxyapatite was produced by the precipitation method, wet method with ion molar ratio of Ca 10 (PO 4) 6 (OH) 2, in which the Ca / P ratio was equal to 1.67. The reaction conditions were favorable to the composition of a biomaterial with crystalline phase. The synthesis of the biomaterial composed of hydroxyapatite and alginate microspheres (HAAlg5%; 200 ø 425mm) was obtained from two primary solutions with the aim of, in optimal reactive conditions, to form the precipitate. After synthesis the microspheres were implanted into the defect site. The potential effects of using HAAlg5% and the application of vibratory waves in the critical defect repair were unknown and the results described in this study are promising, considering the systemic therapy and at the site of injury. The biomaterial used promoted repair the injured tissue.

Preparation and Characterization of Nanocomposite Calcium Doped Ceria Electrolyte With Alkali Carbonates (NK-CDC) for SOFC

2010 ◽  
Author(s):  
Ghazanfar Abbas ◽  
Rizwan Raza ◽  
Muhammad Ashraf Chaudhry ◽  
Bin Zhu
Keyword(s):  
Electron Microscopy ◽  
Fossil Fuels ◽  
Electrochemical Impedance ◽  
Renewable Energy Sources ◽  
Precipitation Method ◽  
Molar Ratio ◽  
Doped Ceria ◽  
Alternative Source ◽  
Calcium Doped ◽  
Co Precipitation

The entire world’s challenge is to find out the renewable energy sources due to rapid depletion of fossil fuels because of their high consumption. Solid Oxide Fuel Cells (SOFCs) are believed to be the best alternative source which converts chemical energy into electricity without combustion. Nanostructured study is required to develop highly ionic conductive electrolyte for SOFCs. In this work, the calcium doped ceria (Ce0.8Ca0.2O1.9) coated with 20% molar ratio of two alkali carbonates (CDC-M: MCO3, where M = Na and K) electrolyte was prepared by co-precipitation method in this study. Ni based electrode was used to fabricate the cell by dry pressing technique. The crystal structure and surface morphology was characterized by X-Ray Diffractometer (XRD), Scanning Electron Microscopy (SEM) and High Resolution Transmission Electron Microscopy (HRTEM). The particle size was calculated in the range of 10–20nm by Scherrer’s formula and compared with SEM and TEM results. The ionic conductivity was measured by using AC Electrochemical Impedance Spectroscopy (EIS) method. The activation energy was also evaluated. The performance of the cell was measured 0.567W/cm2 at temperature 550°C with hydrogen as a fuel.

Effect of the Synthesis Method on the Properties of Ultrafine YAG Powder

2018 ◽  
Vol 281 ◽  
pp. 40-45
Author(s):  
Jie Guang Song ◽  
Lin Chen ◽  
Cai Liang Pang ◽  
Jia Zhang ◽  
Xian Zhong Wang ◽  
...  
Keyword(s):  
Particle Size ◽  
Calcination Temperature ◽  
Hydrothermal Reaction ◽  
Synthesis Method ◽  
Particle Morphology ◽  
Precipitation Method ◽  
Molar Ratio ◽  
Synthesis Process ◽  
Powder Materials ◽  
Co Precipitation

YAG materials has a number of unique properties, the application is very extensive. In this paper, the superfine YAG powder materials were prepared by co-precipitation method and hydrothermal precipitation method. The influence of synthesis process on the morphology of the powder was investigated. The results showed that the precursor powder prepared via the co-precipitation method is mainly from amorphous to crystalline transition with the increasing calcination temperature, the precursor agglomeration is more serious, In the process of increasing the calcination temperature, the dispersibility of the roasted powder is greatly improved, which is favorable for the growth of the crystal grains, so that the particle size of the powder is gradually increased, the YAG precursor prepared by the co-precipitation method is transformed into YAG crystals, the phase transition occurs mainly between 900 and 1100°C. When the molar ratio of salt to alkali is Y3+: OH-=1: 8 via the hydrothermal reaction, the YAG particles with homogeneous morphology can be obtained. When the molar ratio of salt and alkali is increased continuously, the morphology of YAG particles is not obviously changed. The co-precipitation method is easy to control the particle size, the hydrothermal method is easy to control the particle morphology.

Controlled Synthesis of Different Morphologies of SrWO4 Crystals via a Surfactant-Assisted Hydrothermal Precipitation Method

2013 ◽  
Vol 785-786 ◽  
pp. 449-454
Author(s):  
Yan Zhao ◽  
Chun Yan Wu ◽  
Dan Qin ◽  
Xin Lai ◽  
Si Wu ◽  
...  
Keyword(s):  
Ph Value ◽  
Precipitation Method ◽  
Molar Ratio ◽  
X Ray Diffraction ◽  
X Ray ◽  
Experimental Parameters ◽  
Infrared Spectrometer ◽  
Luminescent Spectra ◽  
Hydrothermal Precipitation ◽  
Surfactant Assisted

SrWO4 octahedrons, flowers, bundles, ellipsoids and dendrites had been successfully synthesized via surfactant-assisted method. The products were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), photo-luminescent spectra techniques (PL) and fourier transrform infrared spectrometer (FTIR). By through various comparison experiments, it can be found that some related experimental parameters including the reagent concentration, [Sr2+]/[WO42-] molar ratio (R), aging temperature and the pH value had great influences on morphology of the products.

Sign in / Sign up

Export Citation Format

Share Document