scholarly journals Low Water Absorption, High-Strength Polyamide 6 Composites Blended with Sustainable Bamboo-Based Biochar

Nanomaterials ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 1367
Author(s):  
Shiliu Zhu ◽  
Yong Guo ◽  
Yuxia Chen ◽  
Shengquan Liu
Keyword(s):  
Mechanical Properties ◽  
Mechanical Strength ◽  
Water Absorption ◽  
High Strength ◽  
Polyamide 6 ◽  
Negative Effects ◽  
Plant Fibers ◽  
Maximum Decrease ◽  
Bamboo Fibers ◽  
The Impact

To promote the application of polyamide 6 (PA6) in wood–plastic composites, the negative effects associated with the thermal degradation of plant fibers must be overcome. In this study, waste bamboo fibers were subjected to pyrolysis and ball milling to afford nano bamboo-based biochar (BC), which was subsequently used as reinforcement to prepare PA6/BC nano composites by injection molding. In addition, the processing fluidity, water absorption, mechanical properties, and interface compatibility of PA6/BC composites were discussed. Results revealed that a BC content of less than 30 wt% is beneficial to improve the processing fluidity of the composites. With the increase in the BC content, the density of the PA6/BC composites gradually increased, while the water absorption of the PA6/BC composites gradually decreased, and the maximum decrease was 46%. Compared to that of pure PA6, the mechanical strength of PA6/BC composites was improved by the addition of BC, and the maximum tensile/flexural strength and modulus of PA6/BC composites increased by 41%/72% and 195%/244%, respectively. However, the impact strength decreased by 27%. After immersion treatment, the dimensional stability and mechanical strength of the composites decreased, while toughness improved. At a BC content of less than 40 wt%, BC particles exhibited good dispersibility and wettability in the PA6 matrix, and the rough surface and rich pore structure of BC rendered strong mechanical interlocking effects and good interface compatibility, thereby enhancing the mechanical properties of the composites.

scholarly journals High-strength and fibrous capsule–resistant zwitterionic elastomers

2021 ◽  
Vol 7 (1) ◽  
pp. eabc5442
Author(s):  
Dianyu Dong ◽  
Caroline Tsao ◽  
Hsiang-Chieh Hung ◽  
Fanglian Yao ◽  
Chenjue Tang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mechanical Strength ◽  
High Strength ◽  
Design Principles ◽  
Fibrous Capsule ◽  
High Mechanical Strength ◽  
Capsule Formation ◽  
Locking Mechanism ◽  
Fibrous Capsule Formation

The high mechanical strength and long-term resistance to the fibrous capsule formation are two major challenges for implantable materials. Unfortunately, these two distinct properties do not come together and instead compromise each other. Here, we report a unique class of materials by integrating two weak zwitterionic hydrogels into an elastomer-like high-strength pure zwitterionic hydrogel via a “swelling” and “locking” mechanism. These zwitterionic-elastomeric-networked (ZEN) hydrogels are further shown to efficaciously resist the fibrous capsule formation upon implantation in mice for up to 1 year. Such materials with both high mechanical properties and long-term fibrous capsule resistance have never been achieved before. This work not only demonstrates a class of durable and fibrous capsule–resistant materials but also provides design principles for zwitterionic elastomeric hydrogels.

scholarly journals Numerical Studies of the Effects of Water Capsules on Self-Healing Efficiency and Mechanical Properties in Cementitious Materials

2016 ◽  
Vol 2016 ◽  
pp. 1-10 ◽  
Author(s):  
Haoliang Huang ◽  
Guang Ye
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elastic Modulus ◽  
Cementitious Materials ◽  
Self Healing ◽  
Negative Effects ◽  
Numerical Studies ◽  
Healing Efficiency ◽  
The Impact ◽  
Positive Effect

In this research, self-healing due to further hydration of unhydrated cement particles is taken as an example for investigating the effects of capsules on the self-healing efficiency and mechanical properties of cementitious materials. The efficiency of supply of water by using capsules as a function of capsule dosages and sizes was determined numerically. By knowing the amount of water supplied via capsules, the efficiency of self-healing due to further hydration of unhydrated cement was quantified. In addition, the impact of capsules on mechanical properties was investigated numerically. The amount of released water increases with the dosage of capsules at different slops as the size of capsules varies. Concerning the best efficiency of self-healing, the optimizing size of capsules is 6.5 mm for capsule dosages of 3%, 5%, and 7%, respectively. Both elastic modulus and tensile strength of cementitious materials decrease with the increase of capsule. The decreasing tendency of tensile strength is larger than that of elastic modulus. However, it was found that the increase of positive effect (the capacity of inducing self-healing) of capsules is larger than that of negative effects (decreasing mechanical properties) when the dosage of capsules increases.

Physical Simulation of Weldability of Weldox 1300 Steel

2013 ◽  
Vol 762 ◽  
pp. 551-555 ◽  
Author(s):  
Marek Stanislaw Węglowski ◽  
Marian Zeman ◽  
Miroslaw Lomozik
Keyword(s):  
Mechanical Properties ◽  
Impact Toughness ◽  
Physical Simulation ◽  
High Strength ◽  
Parent Material ◽  
Cooling Time ◽  
Electron Microscopies ◽  
Transmission Electron ◽  
Transformation Diagrams ◽  
The Impact

In the present study, the investigation of weldability of new ultra-high strength - Weldox 1300 steel has been presented. The thermal simulated samples were used to investigate the effect of welding cooling time t8/5 on the microstructure and mechanical properties of the heat affected zone (HAZ). In the frame of these investigation the microstructure was studied by the light (LM) and transmission electron microscopies (TEM). It has been shown that the microstructure of the Weldox 1300 steel is composed of tempered martensite, and inside the laths the minor precipitations mainly V(CN) and molybdenum carbide Mo2C were observed. Mechanical properties of parent material were analysed by the tensile, impact and hardness tests. In details the influence of cooling time in the range of 2,5 - 300 s. on hardness, impact toughness and microstructure of simulated HAZ was studied by using welding thermal simulation test. The results show that the impact toughness and hardness decrease with the increase of t8/5 under the condition of a single thermal cycle in simulated HAZ. The continuous cooling transformation diagrams (CCT-W for welding conditions) of Weldox 1300 steel for welding purposes was also elaborated. The steel Weldox 1300 for cooling time in the range of 2,5 - 4 s showed martensite microstructure, for time from 4 s to 60 s mixture of martensite and bainite, and for longer cooling time mixture of ferrite, bainite and martensite. The results indicated that the weldability of Weldox 1300 steel is limited and to avoid the cold cracking the preheating procedure or medium net linear heat input should be used.

Revealing Mechanical Strength of Nanopores Using Atomic Finite Element Techniques

2018 ◽  
Vol 934 ◽  
pp. 24-29
Author(s):  
Prapasiri Pongprayoon ◽  
Attaphon Chaimanatsakun
Keyword(s):  
Mechanical Properties ◽  
Finite Element Method ◽  
Finite Element ◽  
Fluid Flow ◽  
Mechanical Strength ◽  
Impact Force ◽  
Pore Surface ◽  
Vertical Rectangle ◽  
The Impact ◽  
Graphene Nanopore

Graphene nanopore has been widely employed in nanofilter or nanopore devices due to its outstanding properties. The understanding of its mechanical properties at nanoscale is crucial for device improvement. In this work, the mechanical properties of graphene nanopore is thus investigated using atomistic finite element method (AFEM). Four graphene models with different pore shapes (circular (CR), horizontal rectangle (RH), and vertical rectangle (RV)) in sub-nm size which could be successfully fabricated experimentally have been studied here. The force normal to a pore surface is applied to mimic the impact force due to a fluid flow. Increasing pore size results in the reduction in its strength. Comparing among different pore shapes with comparable sizes, the order of pore strength is CR>RH>RV>SQ. In addition, we observe that the direction of pore alignment and geometries of pore edge also play a key role in mechanical strength of nanopores.

Synthesis of Polyvinyl Formal Sponge for Wound Care Dressing Application

2010 ◽  
Vol 152-153 ◽  
pp. 1650-1659
Author(s):  
Qing Hao Yang ◽  
Guang Xu Cheng ◽  
Zhi Cheng Zhang
Keyword(s):  
Mechanical Properties ◽  
Mechanical Strength ◽  
Porous Structure ◽  
Pore Structure ◽  
Water Absorption ◽  
Wound Dressing ◽  
Wound Care ◽  
Acid Catalyst ◽  
The Other ◽  
Polyvinyl Formal

In an effort to seek poly(vinyl formal) (PVFM) foams based wound dressing pad material, a series of foamed PVFM materials have been synthesized under varied conditions. The influence of conditions on the properties of PVFM foam, such as mechanical properties, water absorption, pore structure and bulk density, is well discussed individually. It has been shown that both the reactant and acid catalyst affect the degree and speed of acetalization, therefore the mechanical properties, pores continuity and water absorption of the resultant sample. The addition of Na2CO3, surfactant and CMCNa are mainly influencing the porous structure as well as the mechanical properties and water absorption. One best sample with balanced properties is obtained. It possesses higher mechanical strength and water absorption while the other properties are similar, comparing with a commercial surgical PVFM sponge (YJ-1) currently used.

An attempt to use „Tetra Pak” waste material in particleboard technology

2021 ◽  
Vol 114 ◽  
pp. 70-75
Author(s):  
Radosław Auriga ◽  
Piotr Borysiuk ◽  
Alicja Auriga
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Bending Strength ◽  
Physical And Mechanical Properties ◽  
Core Layer ◽  
Waste Material ◽  
Thickness Swelling ◽  
The Core ◽  
Tetra Pak ◽  
The Impact

An attempt to use „Tetra Pak” waste material in particleboard technology. The study investigates the effect of addition Tetra Pak waste material in the core layer on physical and mechanical properties of chipboard. Three-layer chipboards with a thickness of 16 mm and a density of 650 kg / m3 were manufactured. The share of Tetra Pak waste material in the boards was varied: 0%, 5%, 10% and 25%. The density profile was measured to determine the impact of Tetra Pak share on the density distribution. In addition, the manufactured boards were tested for strength (MOR, MOE, IB), thickness swelling and water absorption after immersion in water for 2 and 24 hours. The tests revealed that Tetra Pak share does not affect significantly the value of static bending strength and modulus of elasticity of the chipboard, but it significantly decreases IB. Also, it has been found that Tetra Pak insignificantly decreases the value of swelling and water absorption of the chipboards.

scholarly journals Properties of Latex Polymer Modified Mortars Reinforced with Waste Bamboo Fibers from Construction Waste

Buildings ◽  
2018 ◽  
Vol 8 (11) ◽  
pp. 149 ◽  
Author(s):  
Banjo Akinyemi ◽  
Temidayo Omoniyi
Keyword(s):  
Mechanical Properties ◽  
High Strength ◽  
Latex Paint ◽  
Construction Waste ◽  
Calcium Silicate Hydrates ◽  
Cement Mortars ◽  
The Matrix ◽  
Bamboo Fibers ◽  
Pre Treatment ◽  
Scanning Electron

This study evaluated the properties of latex modified cement mortars from ordinary paints which were reinforced with treated bamboo fibers from construction waste. Fiber variations of 0, 0.5, 1 and 1.5% at 10% of the weight of cement were utilized. Mechanical properties were determined according to standards; similarly, scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) were used to analyze the microstructural and elemental properties of the samples. The experimental results revealed that the addition of 1.5% bamboo fibers and 10% latex solution produced excellent mechanical properties. This was as a result of improved fiber adhesion to the matrix through pre-treatment, coupled with the contributed high strength from the latex paint modified mortars. The micrograph showed that latex precipitated in the voids and on the surface of the bamboo fibers as well as gels of calcium silicate hydrates which contributed to the observed improvement in strength of the tested samples.

scholarly journals Thermal Action on Normal and High Strength Cement Mortars

2020 ◽  
Vol 10 (18) ◽  
pp. 6455
Author(s):  
Marianela Ripani ◽  
Hernán Xargay ◽  
Ignacio Iriarte ◽  
Kevin Bernardo ◽  
Antonio Caggiano ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Peak Load ◽  
Physical And Mechanical Properties ◽  
Thermal Action ◽  
High Strength ◽  
Strength Loss ◽  
Brittle Behavior ◽  
Cement Mortars ◽  
Water Absorption Test

High temperature effect on cement-based composites, such as concrete or mortars, represents one of the most important damaging process that may drastically affect the mechanical and durability characteristics of structures. In this paper, the results of an experimental campaign on cement mortars submitted to high temperatures are reported and discussed. Particularly, two mixtures (i.e., Normal (MNS) and High Strength Mortar (MHS)) having different water-to-binder ratios were designed and evaluated in order to investigate the incidence of both the mortar composition and the effects of thermal treatments on their physical and mechanical properties. Mortar specimens were thermally treated in an electrical furnace, being submitted to the action of temperatures ranging from 100 to 600 °C. After that and for each mortar quality and considered temperature, including the room temperature case of 20 °C, water absorption was measured by following a capillary water absorption test. Furthermore, uniaxial compression, splitting tensile and three-points bending tests were performed under residual conditions. A comparative analysis of the progressive damage caused by temperature on physical and mechanical properties of the considered mortars types is presented. On one hand, increasing temperatures produced increasing water absorption coefficients, evidencing the effect of thermal damages which may cause an increase in the mortars accessible porosity. However, under these circumstances, the internal porosity structure of lower w/b ratio mixtures results much more thermally-damaged than those of MNS. On the other hand, strengths suffered a progressive degradation due to temperature rises. While at low to medium temperatures, strength loss resulted similar for both mortar types, at higher temperature, MNS presented a relatively greater strength loss than that of MHS. The action of temperature also caused in all cases a decrease of Young’s Modulus and an increase in the strain corresponding to peak load. However, MHS showed a much more brittle behavior in comparison with that of MNS, for all temperature cases. Finally, the obtained results demonstrated that mortar quality cannot be neglected when the action of temperature is considered, being the final material performance dependent on the physical properties which, in turn, mainly depend on the mixture proportioning.

Study of Mechanical Properties and Morphology of PA 6/PO Blends Compatibilized by PO Grafted with Itaconic Acid

e-Polymers ◽  
2007 ◽  
Vol 7 (1) ◽  
Author(s):  
Liu Xijun ◽  
Jiang Zhaohua ◽  
Zhu Wenming
Keyword(s):  
Mechanical Properties ◽  
Graft Copolymer ◽  
Flow Rate ◽  
Itaconic Acid ◽  
Polyamide 6 ◽  
Glass Temperature ◽  
Melt Flow ◽  
Melt Flow Rate ◽  
Twin Screw ◽  
The Impact

AbstractTwo different types of polyolefine (PO) grafted with itaconic acid as a reactive compatibilizer, polypropylene (PP) grafted with itaconic acid (PP-g-ITA) and high density polyethylene (HDPE) grafted with itaconic acid (HDPE-g-ITA), PP and HDPE grafted with copolymer of itaconic acid and styrene (PP-g-(ITA-St) and HDPE-g-(ITA-St)) were prepared by melt graft technique through reactive type twin-screw extruder. FT-IR and thermal analysis were used to characterize the structure of the graft copolymer. The graft ratio (GR) and melt flow rate (MFR) were determined by non-aqueous titration and melt flow rate analyzer. The effect of the concentration of monomer and initiator dosage on GR and MFR of graft copolymer were studied. Then polyamide 6 (PA 6) blends, PA 6/PP (PA 6/HDPE), that compatibilized with PP-g-ITA (HDPE-g-ITA) were prepared. The morphology of the blends was analyzed by SEM, DSC and Molau tests and the mechanical properties of which were characterized by tensile, impact, and bend tests. The results of mechanical property showed that the impact strength of blends was increased by 50% and 70% after PP-g-ITA and HDPE-g-ITA was used as compatibilizer, but the MFR of blends was decreased. The SEM photographs indicated that the accession of compatibilizer obviously improved binding state between two phases in blends, the size of dispersed phase was reduced evidently and the interface became indistinct. DSC results demonstrated that in the case of PP-g-ITA, glass temperature (Tg) of PA 6 matrix in blends was ascended, melt point (Tm) was improved a little, crystallinity (Xc) was decreased, Tm and Xc of PP phase was increased; With the accession of HDPE-g-ITA, Tm of PA 6 matrix and HDPE phase had almost no change, Xc of PA 6 matrix was decreased and Xc of HDPE phase was increased.

Sign in / Sign up

Export Citation Format

Share Document