scholarly journals Nanodiamond Particles as Secondary Additive for Polyalphaolefin Oil Lubrication of Steel–Aluminium Contact

Nanomaterials ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 1438
Author(s):  
Ankush Raina ◽  
Mir Irfan Ul Haq ◽  
Ankush Anand ◽  
Sanjay Mohan ◽  
Rajiv Kumar ◽  
...  
Keyword(s):  
Coefficient Of Friction ◽  
Hexagonal Boron Nitride ◽  
Normal Load ◽  
Lubricant Additive ◽  
Oil Lubrication ◽  
Volumetric Wear ◽  
Base Oil ◽  
Applied Normal Load ◽  
Lubrication Performance ◽  
The Coefficient Of Friction

Nanodiamond (ND) particles are effective lubricant additives. Attention of research has shifted towards investigating the particles as secondary additives. ND particles provide more benefits as secondary additives than as the sole lubricant additive for steel–steel contacts. In this work, the influence of ND particles as secondary additives on oil lubrication of steel–aluminium tribopair (hard–soft contact) was examined. AISI 52100 steel balls were slid against AA2024 aluminium alloy discs, in the presence of polyalphaolefin (PAO) base oil, in boundary lubrication regime (applied normal load: 10 N to 50 N). Primary additives were copper oxide (CuO) and hexagonal boron nitride (h-BN) nanoparticles. The addition of ND particles to PAO, with CuO and h-BN as primary additives, at the lowest applied normal load of 10 N: (i) decreased the volumetric wear of the aluminium discs by 28% and 63%, respectively, and (ii) decreased the coefficient of friction by 15% and 33%, respectively. At the highest applied normal load of 50 N, it: (i) decreased the volumetric wear of the aluminium discs by 20% and 38%, respectively, and (ii) decreased the coefficient of friction by 5.4% and 8%, respectively. ND particles as secondary additives significantly reduce energy loss and power loss as a consequence of an effective reduction in friction during sliding. Unique characteristics of ND particles—such as their (a) physicochemical and thermal properties, (b) ball bearing and polishing effects and (c) synergistic interaction with primary additives to form stable tribofilms—enhance the lubrication performance of steel–aluminium contact. ND particles in combination with h-BN nanoparticles showed the best performance, due to better synergy between the primary additive and the secondary additive. Results from the investigation indicate that ND particles taken as secondary additives in small amount (0.2 wt%) can improve oil lubrication performance of hard–soft contacts in engineering systems.

scholarly journals Modified graphene as novel lubricating additive with high dispersion stability in oil

Friction ◽  
2020 ◽  
Vol 9 (1) ◽  
pp. 143-154 ◽  
Author(s):  
Pu Wu ◽  
Xinchun Chen ◽  
Chenhui Zhang ◽  
Jiping Zhang ◽  
Jianbin Luo ◽  
...  
Keyword(s):  
Friction And Wear ◽  
Wear Track ◽  
Normal Load ◽  
Lubricant Additive ◽  
Tribological Performance ◽  
Dispersion Stability ◽  
High Dispersion ◽  
Base Oil ◽  
The Coefficient Of Friction ◽  
Modified Graphene

Abstract Graphene is a promising material as a lubricant additive for reducing friction and wear. Here, a dispersing method which combines chemical modification of graphene by octadecylamine and dicyclohexylcarbodiimide with a kind of effective dispersant has been successfully developed to achieve the remarkable dispersion stability of graphene in base oil. The stable dispersion time of modified graphene (0.5 wt%) with dispersant (1 wt%) in PAO-6 could be up to about 120 days, which was the longest time reported so far. At the same time, the lubricant exhibits a significant improvement of tribological performance for a steel ball to plate tribo-system with a normal load of 2 N. The coefficient of friction between sliding surfaces was ~0.10 and the depth of wear track on plate was ~21 nm, which decreased by about 44% and 90% when compared to pure PAO-6, respectively. Furthermore, the analysis of the lubricating mechanisms in regard to the sliding-induced formation of nanostructured tribo-film has been contacted by using Raman spectra and TEM.

Effect of Micro-Size Cenosphere Content on Friction and Dry Sliding Wear Behavior of Vinylester Composites – A Taguchi Method

2012 ◽  
Vol 585 ◽  
pp. 569-573 ◽  
Author(s):  
S.R. Chauhan ◽  
Sunil Thakur
Keyword(s):  
Wear Rate ◽  
Coefficient Of Friction ◽  
Sliding Wear ◽  
Friction And Wear ◽  
Normal Load ◽  
Dry Sliding ◽  
Sliding Speed ◽  
Applied Normal Load ◽  
The Coefficient Of Friction ◽  
Sliding Distance

In this paper the friction and wear characteristics of vinylester and vinylester composites have been investigated under dry sliding conditions for different applied normal load, sliding speed and sliding distance. The experiments have been carried on a pin on disc arrangement at normal room temperature conditions. The influence of friction and wear parameters like normal load, speed, sliding distance and percentage of filler content on the friction and wear rate has been investigated. In this study, a plan of experiments based on the techniques of Taguchi was performed to acquire data in a controlled way. An orthogonal array L27 (313) and Analysis of variance (ANOVA) were applied to investigate the influence of process parameters on the coefficient of friction and sliding wear behaviour of these composites. The Taguchi design of experiment approach eliminates the need for repeated experiments and thus saves time, material and cost. The results showed that with increase in the applied normal load and sliding speed the coefficient of friction and specific wear rate decreases under dry sliding conditions. It is also found that a thin film formed on the counterface seems to be effective in improving the tribological characteristics. The results showed that the inclusion of cenosphere as filler materials in vinylester composites will increase the wear resistance of the composite significantly.

Study of behaviour of aluminium oxide nanoparticles suspended in SAE20W40 oil under extreme pressure lubrication

2015 ◽  
Vol 67 (4) ◽  
pp. 328-335 ◽  
Author(s):  
Avinash A. Thakre ◽  
Animesh Thakur
Keyword(s):  
Coefficient Of Friction ◽  
Normal Load ◽  
Friction Reduction ◽  
Lubricating Oil ◽  
Extreme Pressure ◽  
Sliding Speed ◽  
Content Type ◽  
Base Oil ◽  
Pin On Disc ◽  
The Coefficient Of Friction

Purpose – The purpose of this paper is to include investigation on extreme pressure lubrication behaviour of Al2O3 nanoparticles suspended in SAE20W40 lubricating oil. Effects of nanoparticles size (40-80 nm) and its concentration (0-1 per cent) on the coefficient of friction is studied using pin-on-disc tribotester. Design/methodology/approach – Taguchi technique is used to optimize the process parameters for lower coefficient of friction. L18 orthogonal array involving six levels for one factor and three levels for remaining three factors is selected for the experimentation. The parameters selected for the study are sliding speed, normal load, nanoparticles size and its concentration in base oil. Findings – It has been found that the presence of nanoparticles in proper concentration shows excellent tribological improvement in frictional characteristics compared to the base oil. The optimal combination of the parameters for minimum coefficient of friction is found to be 0.8 per cent concentration of 60 nm sized Al2O3 nanoparticles, 1,200 rpm sliding speed and 160 N of normal load. The mechanism of friction reduction in presence of nanoparticles is investigated using scanning electron microscopy. Originality/value – This is the original work.

Experimental Investigation of aluminum doping crumb rubber/epoxy composite in reciprocating motion

2015 ◽  
Vol 3 ◽  
pp. 1
Author(s):  
Goutam Chandra Karar ◽  
Nipu Modak
Keyword(s):  
Experimental Investigation ◽  
Coefficient Of Friction ◽  
Epoxy Composite ◽  
Normal Load ◽  
Crumb Rubber ◽  
The Other ◽  
Reciprocating Motion ◽  
Molding Process ◽  
Friction Tester ◽  
The Coefficient Of Friction

The experimental investigation of reciprocating motion between the aluminum doped crumb rubber /epoxy composite and the steel ball has been carried out under Reciprocating Friction Tester, TR-282 to study the wear and coefficient of frictions using different normal loads (0.4Kg, 0.7Kgand1Kg), differentfrequencies (10Hz, 25Hz and 40Hz).The wear is a function of normal load, reciprocating frequency, reciprocating duration and the composition of the material. The percentage of aluminum presents in the composite changesbut the other components remain the same.The four types of composites are fabricated by compression molding process having 0%, 10%, 20% and 30% Al. The effect of different parameters such as normal load, reciprocating frequency and percentage of aluminum has been studied. It is observed that the wear and coefficient of friction is influenced by the parameters. The tendency of wear goes on decreasing with the increase of normal load and it is minimum for a composite having 10%aluminum at a normal load of 0.7Kg and then goes on increasing at higher loads for all types of composite due to the adhesive nature of the composite. The coefficient of friction goes on decreasing with increasing normal loads due to the formation of thin film as an effect of heat generation with normal load.

The Effect of Nanoparticle Functionalization on Lubrication Performance of Nanofluids Dispersing Silica Nanoparticles in an Ionic Liquid

2017 ◽  
Vol 139 (4) ◽  
Author(s):  
Cengiz Yegin ◽  
Wei Lu ◽  
Bassem Kheireddin ◽  
Ming Zhang ◽  
Peng Li ◽  
...  
Keyword(s):  
Silica Nanoparticles ◽  
Coefficient Of Friction ◽  
Shear Thinning ◽  
Antiwear Additives ◽  
Functionalized Silica ◽  
Low Concentrations ◽  
Lubrication Performance ◽  
The Coefficient Of Friction ◽  
High Concentrations ◽  
Newtonian Behavior

Recently, ionic liquids (ILs) have received an increasing attention as lubricants owing to their intriguing properties such as tunable viscosity, high thermal stability, low emissions, nonflammability, and corrosion resistance. In this work, we investigate how the incorporation of octadecyltrichlorosilane (OTS) functionalized silica nanoparticles (NPs) in 1-butyl-3-methylimidazolium (trifluoromethysulfony)imide influences the tribological properties and rheological properties of IL under boundary lubrication and elastohydrodynamic conditions, respectively. It was found that the coefficient of friction was depended on the concentration of NPs in IL with a concave upward functional trend with a minimum at 0.05 wt.% for bare silica NPs and at 0.10 wt.% for OTS-functionalized silica NPs. For steel–steel sliding contact, the presence of functionalized NPs in IL at the optimum concentration decreased the coefficient of friction by 37% compared to IL and 17% compared to IL with bare silica NPs. While IL with bare NPs demonstrated a shear thinning behavior for all concentrations, IL with functionalized NPs showed a Newtonian behavior at low concentrations and shear thinning behavior at high concentrations. Overall, this study provides new insights into the antifriction and antiwear additives for lubrication systems involving ILs.

Stresses Due to Tangential and Normal Loads on an Elastic Solid With Application to Some Contact Stress Problems

1953 ◽  
Vol 20 (2) ◽  
pp. 157-166
Author(s):  
J. O. Smith ◽  
Chang Keng Liu
Keyword(s):  
Plane Strain ◽  
Coefficient Of Friction ◽  
Contact Area ◽  
Normal Load ◽  
Elastic Solid ◽  
Real Variable ◽  
The Body ◽  
Shearing Stress ◽  
Tangential Load ◽  
The Coefficient Of Friction

Abstract The results of two-dimensional approach using real variable method to Hertz’s problem of contact of elastic bodies are presented. Both normal and tangential loads are assumed to be distributed in Hertzian fashion over the area of contact. The magnitude of the intensity of the tangential load is assumed to be linearly proportional to that of the normal load when sliding motion of the body is impending. The stresses in the elastic body due to the application of these loads on its boundary are presented in closed form for both plane-stress and plane-strain cases. A numerical value of f = 1/3 is assumed for the linear proportionality (coefficient of friction) between the tangential and normal loads in order that the distribution of stresses may be illustrated. The significance of the stress distribution, across the contact area and in the body, is also discussed. It is shown that when the combination of loads considered in the paper are applied at the contact area of bodies in contact the maximum shearing stress may be at the surface instead of beneath the surface. For example, for plane strain, if the coefficient of friction is f = 1/3, the maximum shearing stress is at the surface and is 43 per cent larger than the maximum shearing stress, which would be below the surface, that occurs when the normal force acts alone. The effect of range of normal stress and of shearing stress on the plane of maximum shear and on the plane of maximum octahedral shear on failure by progressive fracture (fatigue) is discussed.

scholarly journals Finger pad friction and its role in grip and touch

2013 ◽  
Vol 10 (80) ◽  
pp. 20120467 ◽  
Author(s):  
Michael J. Adams ◽  
Simon A. Johnson ◽  
Philippe Lefèvre ◽  
Vincent Lévesque ◽  
Vincent Hayward ◽  
...  
Keyword(s):  
Contact Zone ◽  
Coefficient Of Friction ◽  
Normal Load ◽  
Theoretical Models ◽  
Tactile Perception ◽  
Major Influence ◽  
Sliding Velocity ◽  
Stick Slip ◽  
The Coefficient Of Friction ◽  
Finger Pad

Many aspects of both grip function and tactile perception depend on complex frictional interactions occurring in the contact zone of the finger pad, which is the subject of the current review. While it is well established that friction plays a crucial role in grip function, its exact contribution for discriminatory touch involving the sliding of a finger pad is more elusive. For texture discrimination, it is clear that vibrotaction plays an important role in the discriminatory mechanisms. Among other factors, friction impacts the nature of the vibrations generated by the relative movement of the fingertip skin against a probed object. Friction also has a major influence on the perceived tactile pleasantness of a surface. The contact mechanics of a finger pad is governed by the fingerprint ridges and the sweat that is exuded from pores located on these ridges. Counterintuitively, the coefficient of friction can increase by an order of magnitude in a period of tens of seconds when in contact with an impermeably smooth surface, such as glass. In contrast, the value will decrease for a porous surface, such as paper. The increase in friction is attributed to an occlusion mechanism and can be described by first-order kinetics. Surprisingly, the sensitivity of the coefficient of friction to the normal load and sliding velocity is comparatively of second order, yet these dependencies provide the main basis of theoretical models which, to-date, largely ignore the time evolution of the frictional dynamics. One well-known effect on taction is the possibility of inducing stick–slip if the friction decreases with increasing sliding velocity. Moreover, the initial slip of a finger pad occurs by the propagation of an annulus of failure from the perimeter of the contact zone and this phenomenon could be important in tactile perception and grip function.

Study on the effects of nano-aluminum-oxide particulates on mechanical and tribological characteristics of chopped carbon fiber reinforced epoxy composites

2015 ◽  
Vol 231 (4) ◽  
pp. 403-422 ◽  
Author(s):  
Kali Dass ◽  
SR Chauhan ◽  
Bharti Gaur
Keyword(s):  
Carbon Fiber ◽  
Wear Rate ◽  
Coefficient Of Friction ◽  
Normal Load ◽  
Epoxy Composites ◽  
Specific Wear Rate ◽  
Tribological Characteristics ◽  
X Ray ◽  
The Coefficient Of Friction ◽  
Mechanical And Tribological Characteristics

An experimental study has been carried out to investigate the mechanical and tribological characteristics of chopped carbon fiber (CCF) reinforced epoxy composites filled with nano-Al2O3 particulates, as a function of fiber and filler contents. The experiments were conducted using a pin-on-disc wear test apparatus under dry sliding conditions. The coefficient of friction and specific wear rate of these composites was determined as a function of applied normal load, sliding velocity, sliding distance, and reinforcement content. The tensile, flexural, and compression strengths of ortho cresol novalac epoxy and chopped carbon fiber (OCNE/CCF) filled composites are found to be within the ranges of 48–58.54 MPa, 115–156.56 MPa, and 48–61.15 MPa. Whereas the tensile, flexural, and compression strengths of OCNE/CCF/Al2O3-filled composites are found to be within the ranges of 96–110 MPa, 176–204.66 MPa, and 72–85.65 MPa, respectively. It has been observed that the coefficient of friction decreases and specific wear rate increases with increase in the applied normal loads. Further increases in the fiber (6 wt%) and particle (3 wt%) contents in the epoxy matrix resulted in a decrease of both the mechanical and tribological properties, but remains above that of the CCF reinforced epoxy composites. The worn surfaces of composites were examined with scanning electron microscopy equipped with energy dispersion X-ray analyzer and X-ray diffraction analysis technique to investigate the wear mechanisms.

Anisotropic Frictional Behavior of Nanotextured Surfaces

2008 ◽  
Author(s):  
H.-S. Zhang ◽  
K. Komvopoulos
Keyword(s):  
Coefficient Of Friction ◽  
Normal Load ◽  
Ion Beam ◽  
Textured Surfaces ◽  
Friction Mechanism ◽  
Atomic Force ◽  
Afm Imaging ◽  
The Coefficient Of Friction ◽  
Tip Radius ◽  
Adhesion Friction

Silicon wafers were exposed to an oblique Ar+ ion beam to create arrays of surface ripples. Atomic force microscope (AFM) imaging revealed that the rippled (textured) surfaces exhibited highly anisotropic morphologies. Nanoscale friction experiments performed with different diamond tips illustrated a dependence of the coefficient of friction on tip radius, normal load, and sliding direction. Changes in the coefficient of friction are interpreted in terms of the applied normal load and varying contributions of the adhesion friction mechanism.

The Size of the Friction Coefficient Depending on the Size and Course of Normal Load

2014 ◽  
Vol 474 ◽  
pp. 303-308 ◽  
Author(s):  
Eva Labašová
Keyword(s):  
Friction Coefficient ◽  
Coefficient Of Friction ◽  
Normal Load ◽  
Testing Machine ◽  
Constant Load ◽  
Current Component ◽  
Rectangular Shape ◽  
The Coefficient Of Friction ◽  
Ring Method ◽  
Run Up

The coefficient of friction for the bronze material (CuZn25Al6) with inset graphite beds is investigated in the present paper. Friction coefficient was investigated experimentally by the testing machine Tribotestor`89 which uses the principle of the ring on ring method. Tribotestor`89 machine may be classed to the rotary tribometers. The tested sliding pairs were of the same material. The internal bushing performed a rotational movement with constant sliding speed (v = 0.8 m s-1). The external fixed bushing was exposed to the normal load, which was of different sizes and different variations. Process of load was increased from level 50 N to 200 N (400 N, 600 N) during run up 600 s, after the run up the appropriate level of load was held.The forth test had a rectangular shape of loading with direct current component 400 N and the amplitude 200 N period 600 s, the whole test took 1800 s. The obtained results reveal that friction coefficient decreases with the increase of normal load. Further, that the coefficient of friction was found smaller at constant load, as compared to rectangular shape of loading.

Sign in / Sign up

Export Citation Format

Share Document