SIMULATION MEASUREMENT OF CONDUCTIVE INTERFERENCE

2021 ◽  
Author(s):  
А.М. САЖНЕВ ◽  
Л.Г. РОГУЛИНА
Keyword(s):  
Output Voltage ◽  
Electronic Device ◽  
Switching Frequency ◽  
Output Current ◽  
Voltage Converter ◽  
Software Environment ◽  
Load Current ◽  
Frequency Dependences

Разработана модель имитационных испытаний электронного устройства в современной программной среде на основе отечественных компонентов. Проведены имитационные испытания конвертора напряжения на 24 В с выходным током 1,4 А, частотой коммутации 20 кГц и выпрямительного устройства с выходным напряжением 48 В, током нагрузки 28 А. Получены частотные зависимости уровней кондуктивных помех и выполнена их оценка на соответствие нормам. A model of simulation tests of an electronic device in a modern software environment based on domestic components has been developed. Simulation tests of a 24 V voltage converter with an output current of 1.4 A, a switching frequency of 20 kHz, and a rectifier device with an output voltage of 48 V, a load current of 28 A were carried out. The frequency dependences of conductive interference levels were obtained and their compliance with the standards was evaluated.

Study on Current Detecting and Control Method for STATCOM across Transformer

2011 ◽  
Vol 130-134 ◽  
pp. 1933-1937
Author(s):  
Cun Ping Wang ◽  
Xiang Gen Yin ◽  
Jian Liu ◽  
Qing Xiong
Keyword(s):  
Reactive Power ◽  
Control Method ◽  
Electronic Device ◽  
Control Strategies ◽  
Power Electronic ◽  
Output Current ◽  
Load Current ◽  
Decoupling Method ◽  
Reactive Current ◽  
And Control

Static var compensator (STATCOM) is a widely used power electronic device for dynamic reactive power compensation, and its current detecting and control method generally adopts d-q decoupling method based on the synchronous rotating coordinate transformation. However, in the traditional method, the load reactive current component is directly used as the command of STATCOM output current, so it is required that the installation position of STATCOM must be consistent with load current detecting point. But in practice, STATCOM installation point and load current detecting point may be located at two different sides of the transformer. For this situation, this paper proposed an improved reactive current detecting and control method based on the principle of power balance, achieving the current detecting and control strategies when the two points are located at different sides of transformer. Finally, the simulation of system with STATCOM accessed from the third winding of transformer verifies the correctness and feasibility of the proposed method.

scholarly journals Efficiency of Synchronous and Asynchronous Buck-Converter at Low Output Current.

2019 ◽  
Vol 27 (2) ◽  
pp. 194-206
Author(s):  
Ismael Khaleel Murad
Keyword(s):  
Duty Cycle ◽  
Buck Converter ◽  
Voltage Regulator ◽  
Switching Frequency ◽  
Output Current ◽  
Load Current ◽  
Small Load ◽  
Step Down ◽  
Conduction Mode ◽  
Continuous Conduction Mode

In this paper both synchronous and asynchronous buck-converter were designed to work in continuous conduction mode “CCM” and to deliver small load current. Then the two topologies were tested in terms of efficiency at small load current by use of  different values of switching frequencies (range from 150 KHz to 1MHz) and three separated values of duty-cycle (0.4, 0.6 and 0.8).   Obtained results turns out that efficiency of both synchronous and asynchronous buck-converter “switching step-down voltage regulator” responds in a negative manner to the increase in the switching frequency. However, this impact is being stronger in synchronous topology because of magnifying effect of losses related to switching frequency compared to those related to conduction when working at small load currents; this behavior makes obtained efficiency of both topologies in convergent levels when they operated to deliver small output current especially when working with higher switching frequencies. Larger duty-cycle can rise up the efficiency of both topologies.

scholarly journals An Ultra-Wide Load Range Voltage Converter Using Proactive Phase Frequency Modulation for IoT Sensors

Sensors ◽  
2020 ◽  
Vol 20 (21) ◽  
pp. 6279
Author(s):  
Saad Arslan ◽  
Syed Asmat Ali Shah ◽  
HyungWon Kim
Keyword(s):  
Output Voltage ◽  
Sensor Nodes ◽  
Signal Generation ◽  
Switching Frequency ◽  
Cmos Process ◽  
Frequency Range ◽  
Voltage Converter ◽  
Load Range ◽  
High Conversion Efficiency ◽  
Measurement Results

Modern sensor nodes have multiple operating states, which causes a conventional voltage converter to perform poorly over a wide load range of the operating states. This paper proposes a voltage converter whose switching frequency and output voltage are proactively adjusted to maintain high conversion efficiency. This allows the converter to exploit a wider frequency range to cover a wide load range. In addition, the proposed converter uses multiple smaller capacitor banks and employs multiphase operation to provide low output ripple voltage. A distributed topology for non-overlapping signal generation is proposed and used in the converter to minimize the number of wires running from connecting the controller to the converter. The proposed voltage converter has been implemented in a chip using a 0.13 um CMOS process. The measurement results demonstrate the ability to support a wide load range of 10 µA to 10 mA, for switching frequencies ranging from 100 kHz to 200 MHz, while providing an efficiency of above 80%.

scholarly journals Adaptive On-Time Buck Converter with Wave Tracking Reference Control for Output Regulation Accuracy

Energies ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3809
Author(s):  
Pang-Jung Liu ◽  
Mao-Hui Kuo
Keyword(s):  
Output Voltage ◽  
Output Regulation ◽  
Buck Converter ◽  
Maximum Efficiency ◽  
Frequency Variation ◽  
Switching Frequency ◽  
Maximum Output ◽  
Equivalent Series Resistance ◽  
Load Current ◽  
Dc Offset

A ripple-based constant on-time (RBCOT) buck converter with a virtual inductor current ripple (VICR) control can relax the stability constraint of large equivalent series resistance (ESR) at an output capacitor, but output regulation accuracy deteriorates due to the issue with output DC offset. Thus, this paper proposes a wave tracking reference (WTR) control to improve converter stability with low ESR and concurrently eliminate output DC offset on the regulated output voltage. Moreover, an adaptive on-time (AOT) circuit is presented to suppress the switching frequency variation with load current changes in continuous conduction mode. A prototype chip was fabricated in 0.35 µm CMOS technology for validation. The measurement results demonstrate that the maximum output DC offset is 4.1 mV and the output voltage ripple is as small as 3 mV. Furthermore, the switching frequency variation with the AOT circuit is 11 kHz when load current changes from 50 mA to 500 mA, and the measured maximum efficiency is 90.9% for the maximum output power of 900 mW.

scholarly journals Performance Modelling and Design Techniques for Efficiency Improvement in On-chip Switched-Capacitor DC-DC Converter

2022 ◽  
Author(s):  
Sunita Saini ◽  
Davinder Singh Saini
Keyword(s):  
Output Voltage ◽  
Optimization Technique ◽  
Switching Frequency ◽  
Switching Loss ◽  
Performance Modelling ◽  
Two Phase ◽  
Load Current ◽  
Vector Method ◽  
Conduction Loss ◽  
On Chip

Abstract Fundamental charge vector method analysis is a single parameter optimization technique limited to conduction loss assuming all frequency-dependent switching (parasitic) loss negligible. This paper investigates a generalized structure to design DC-DC SC converters based on conduction and switching loss. A new technique is proposed to find the optimum value of switching frequency and switch size to calculate target load current and output voltage that maximize the efficiency. The analysis is done to identify switching frequency and switch size for two-phase 2:1 series-parallel SC converter for a target load current of 2.67mA implemented on a 22nm technology node. Results show that a minimum of 250MHz switching frequency is required for target efficiency more than 90% and the output voltage greater than 0.85V where the switch size of a unit cell corresponds to 10Ω on-resistance. MATLAB and PSpice simulation tools are used for results and validation.

scholarly journals Analysis and Implementation of a Frequency Control DC–DC Converter for Light Electric Vehicle Applications

Electronics ◽  
2021 ◽  
Vol 10 (14) ◽  
pp. 1623
Author(s):  
Bor-Ren Lin
Keyword(s):  
Electric Vehicles ◽  
Output Voltage ◽  
Frequency Control ◽  
Input Voltage ◽  
Pulse Frequency ◽  
Switching Frequency ◽  
Battery Charger ◽  
Dc Microgrid ◽  
Load Voltage ◽  
Transportation Vehicle

In order to realize emission-free solutions and clean transportation alternatives, this paper presents a new DC converter with pulse frequency control for a battery charger in electric vehicles (EVs) or light electric vehicles (LEVs). The circuit configuration includes a resonant tank on the high-voltage side and two variable winding sets on the output side to achieve wide output voltage operation for a universal LEV battery charger. The input terminal of the presented converter is a from DC microgrid with voltage levels of 380, 760, or 1500 V for house, industry plant, or DC transportation vehicle demands, respectively. To reduce voltage stresses on active devices, a cascade circuit structure with less voltage rating on power semiconductors is used on the primary side. Two resonant capacitors were selected on the resonant tank, not only to achieve the two input voltage balance problem but also to realize the resonant operation to control load voltage. By using the variable switching frequency approach to regulate load voltage, active switches are turned on with soft switching operation to improve converter efficiency. In order to achieve wide output voltage capability for universal battery charger demands such as scooters, electric motorbikes, Li-ion e-trikes, golf carts, luxury golf cars, and quad applications, two variable winding sets were selected to have a wide voltage output (50~160 V). Finally, experiments with a 1 kW rated prototype were demonstrated to validate the performance and benefits of presented converter.

Study on System Loss in Distribution Network with DG

2014 ◽  
Vol 672-674 ◽  
pp. 1085-1089
Author(s):  
Jia Meng ◽  
Zai Lin Piao ◽  
Feng Zhou
Keyword(s):  
Theoretical Analysis ◽  
Real Number ◽  
Distribution System ◽  
Distribution Network ◽  
Output Current ◽  
Load Current ◽  
Radial Distribution System ◽  
Operation Optimization ◽  
Voltage Deviation ◽  
Node Voltage

The access of DG changes the operation and structure of traditional distribution network. This study mainly focused on controlling DG output current to reduce network loss of the system. Select a simple radial distribution system as example for theoretical analysis and derive the expressions of load current and node voltage. Assuming that there exists a real number k between DG output current and load. Then list the network loss and voltage deviation expressions. For the purpose of operation optimization, k can be determined by mathematical calculations. It proves that the method has a certain rationality to be effective in controlling network loss.

scholarly journals Experimental validation of new self-voltage balanced 9L-ANPC inverter for photovoltaic applications

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
M. Jagabar Sathik ◽  
Dhafer J. Almakhles ◽  
N. Sandeep ◽  
Marif Daula Siddique
Keyword(s):  
Output Voltage ◽  
Pulse Width Modulation ◽  
Superior Performance ◽  
Modulation Scheme ◽  
Switching Frequency ◽  
Switched Capacitor ◽  
Renewable Energy Resources ◽  
High Quality ◽  
Multilevel Inverters ◽  
Blocking Voltage

AbstractMultilevel inverters play an important role in extracting the power from renewable energy resources and delivering the output voltage with high quality to the load. This paper proposes a new single-stage switched capacitor nine-level inverter, which comprises an improved T-type inverter, auxiliary switch, and switched cell unit. The proposed topology effectively reduces the DC-link capacitor voltage and exhibits superior performance over recently switched-capacitor inverter topologies in terms of the number of power components and blocking voltage of the switches. A level-shifted multilevel pulse width modulation scheme with a modified triangular carrier wave is implemented to produce a high-quality stepped output voltage waveform with low switching frequency. The proposed nine-level inverter’s effectiveness, driven by the recommended modulation technique, is experimentally verified under varying load conditions. The power loss and efficiency for the proposed nine-level inverter are thoroughly discussed with different loads.

Design of a High-Precision Flyback Constant Voltage AC–DC Converter

2017 ◽  
Vol 26 (11) ◽  
pp. 1750175
Author(s):  
Changyuan Chang ◽  
Chao Hong ◽  
Yang Xu ◽  
Hailong Sun ◽  
Yao Chen
Keyword(s):  
High Precision ◽  
Output Voltage ◽  
Control Method ◽  
Switching Frequency ◽  
Constant Voltage ◽  
Light Load ◽  
Wave Generator ◽  
Load Regulation ◽  
High Output

A constant voltage AC–DC converter based on the digital assistant technology is proposed in this paper, which has the advantage of high output precision. In this paper, a novel digital exponential wave generator is adopted in Constant Voltage (CV) mode to replace the normal triangle waveform to obtain a wider range of switching frequency, increasing the accuracy of output voltage under light load. The control chip is implemented based on NEC 1[Formula: see text][Formula: see text]m 5[Formula: see text]V/40[Formula: see text]V HVCMOS process, and a 5[Formula: see text]V/1.2[Formula: see text]A prototype has been built to verify the proposed control method. In PFM mode the deviation of output voltage is within [Formula: see text]% and the load regulation is [Formula: see text]%. Meanwhile, when the load jumps from light to heavy, the minimum output voltage could be maintained above 4.16[Formula: see text]V.

Sign in / Sign up

Export Citation Format

Share Document