Kajian Model Fisik Pengaruh Freeboard dan Susunan Buis Beton Sebagai Pemecah Gelombang Tenggelam Ambang Rendah (Pegar) Dalam Mereduksi Gelombang

2017 ◽  
Vol 1 (2) ◽  
pp. 34
Author(s):  
Zulkarnain Zulkarnain ◽  
Nadjadji Anwar
Keyword(s):  
Low Cost ◽  
Relative Depth ◽  
Submerged Breakwater ◽  
Wave Flume ◽  
Concrete Cylinder ◽  
Engineering Department ◽  
Sea Area ◽  
The Waves ◽  
Transmission Test ◽  
Better Than

The Research Center and Development of Water (Puslitbang) is currently developing the Submerged Breakwater in shallow sea area (PEGAR). The author is interested to examine the material that easily obtained in the field of RCP concrete cylinder. The observation is how it to be ability in function as submerged breakwater an go green and low cost. The physical model of wave transmission test is how the response to the structure in ability to damping of wave as the breakwater function. In this research breakwater used is submerged breakwater type by using concrete cylinder (buis beton). The purpose from this research is to know how the response of breakwater structure to the waves through it, with some variation of the structure by creating a structure with three variations of the arrangement and freeboard that is the relative depth with the crest width is constant. The wave generated test in this study is using regular waves in wave flume at FTSP Civil Engineering Department of Institute Technology Ten November. From the analysis of the effect of the installation of submerged breakwater by using concrete cylinder to the wave damping value, it can be concluded that the factors that are very influential is the freeboard and the composition of concrete cylinder. Scenario A (rigid vertical massive) is capable of producing the smallest value of kt is 0.33. As for scenario B (rigid horyzontal massive) with a damping value of 0.5, while the scenario C (rigid permeable) is only able to produce kt value of 0.71. Scenario A is better than scenario B and C Because the position of arrangement of A is very good used to damp wave in small or big freeboard conditions.

A Novel Wideband transition from Substrate Integrated Waveguide to Rectangular Waveguide

2020 ◽  
Vol 10 ◽  
Author(s):  
Keyur Mahant ◽  
Hiren Mewada ◽  
Amit Patel ◽  
Alpesh Vala ◽  
Jitendra Chaudhari
Keyword(s):  
Rectangular Waveguide ◽  
Printed Circuit Board ◽  
Low Cost ◽  
Single Layer ◽  
Circuit Board ◽  
Substrate Integrated Waveguide ◽  
Ka Band ◽  
Better Than ◽  
Millimeter Wave Circuits ◽  
Wideband Transition

Aim: In this article, wideband substrate integrated waveguide (SIW) and rectangular waveguide (RWG) transition operating in Ka-band is proposed Objective: In this article, wideband substrate integrated waveguide (SIW) and rectangular waveguide (RWG) transition operating in Ka-band is proposed. Method: Coupling patch etched on the SIW cavity to couple the electromagnetic energy from SIW to RWG. Moreover, metasurface is introduced into the radiating patch to enhance bandwidth. To verify the functionality of the proposed structure back to back transition is designed and fabricated on a single layer substrate using standard printed circuit board (PCB) fabrication technology. Results: Measured results matches with the simulation results, measured insertion loss is less than 1.2 dB and return loss is better than 3 dB for the frequency range of 28.8 to 36.3 GHz. By fabricating transition with 35 SRRs bandwidth of the proposed transition can be improved. Conclusion: The proposed transition has advantages like compact in size, easy to fabricate, low cost and wide bandwidth. Proposed structure is a good candidate for millimeter wave circuits and systems.

scholarly journals Wave Breaking in Undular Bores with Shear Flows

Water Waves ◽  
2021 ◽  
Author(s):  
Maria Bjørnestad ◽  
Henrik Kalisch ◽  
Malek Abid ◽  
Christian Kharif ◽  
Mats Brun
Keyword(s):  
Turbulent Flows ◽  
Wave Breaking ◽  
Vries Equation ◽  
Kdv Equation ◽  
Flow Depth ◽  
Present Contribution ◽  
Undular Bore ◽  
Wave Flume ◽  
The Kdv Equation ◽  
The Waves

AbstractIt is well known that weak hydraulic jumps and bores develop a growing number of surface oscillations behind the bore front. Defining the bore strength as the ratio of the head of the undular bore to the undisturbed depth, it was found in the classic work of Favre (Ondes de Translation. Dunod, Paris, 1935) that the regime of laminar flow is demarcated from the regime of partially turbulent flows by a sharply defined value 0.281. This critical bore strength is characterized by the eventual breaking of the leading wave of the bore front. Compared to the flow depth in the wave flume, the waves developing behind the bore front are long and of small amplitude, and it can be shown that the situation can be described approximately using the well known Kortweg–de Vries equation. In the present contribution, it is shown that if a shear flow is incorporated into the KdV equation, and a kinematic breaking criterion is used to test whether the waves are spilling, then the critical bore strength can be found theoretically within an error of less than ten percent.

Potential use of waste from tree pruning and recovered plastic to obtain a building material: Case study of Merida, Mexico

2020 ◽  
Vol 38 (11) ◽  
pp. 1222-1230
Author(s):  
Ricardo Herbé Cruz-Estrada ◽  
Javier Guillén-Mallette ◽  
Carlos Vidal Cupul-Manzano ◽  
Josué Iván Balam-Hernández
Keyword(s):  
Building Material ◽  
Mechanical Performance ◽  
Low Cost ◽  
Weight Ratio ◽  
Plastic Composite ◽  
Trees And Shrubs ◽  
Tree Pruning ◽  
Potential Use ◽  
Better Than

This work presents a study on the use of wood and plastic wastes generated in abundance in Merida, Mexico, to help to reduce them in order to mitigate environmental deterioration. The use of these wastes is proposed to obtain a low-cost building material. So, the escalation process (i.e., extrusion) at the pilot level to obtain a prototype of a wood–plastic composite (WPC) corrugated sheet to evaluate the technical feasibility to make a low-cost product is reported. A corrugated sheet with recycled high-density polyethylene (R-HDPE) was produced. The R-HDPE was collected from Merida’s Separation Plant. The wood came from the trimmings of different varieties of trees and shrubs that are periodically pruned. WPC sheets with virgin HDPE were prepared to assess its effect on the materials’ mechanical performance. The wood/HDPE weight ratio was 40/60. The performance of the WPC sheets was compared with that of commercial products with similar characteristics, namely acrylic and polyester sheets reinforced with fibreglass, and black asphalt-saturated cardboard sheets. Thus, the effect of natural weathering on the maximum tensile tearing force and on the maximum flexural load of the different types of sheets was evaluated. Although the mechanical performance of the WPC sheets was lower than that of the acrylic and polyacrylic sheets, their performance was much better than that of the cheap black asphalt-saturated cardboard sheets. So, they are a good option to be used as low-cost temporary roofing.

scholarly journals Enhancement of WiMAX networks using OPNET modeler platform

2021 ◽  
Vol 23 (3) ◽  
pp. 1510
Author(s):  
Noor Nateq Alfaisaly ◽  
Suhad Qasim Naeem ◽  
Azhar Hussein Neama
Keyword(s):  
High Speed ◽  
Network Performance ◽  
Performance Metrics ◽  
Channel Model ◽  
Low Cost ◽  
Base Station ◽  
Multipath Channel ◽  
Coverage Area ◽  
Wimax Networks ◽  
Better Than

Worldwide interoperability microwave access (WiMAX) is an 802.16 wireless standard that delivers high speed, provides a data rate of 100 Mbps and a coverage area of 50 km. Voice over internet protocol (VoIP) is flexible and offers low-cost telephony for clients over IP. However, there are still many challenges that must be addressed to provide a stable and good quality voice connection over the internet. The performance of various parameters such as multipath channel model and bandwidth over the Star trajectoryWiMAX network were evaluated under a scenario consisting of four cells. Each cell contains one mobile and one base station. Network performance metrics such as throughput and MOS were used to evaluate the best performance of VoIP codecs. Performance was analyzed via OPNET program14.5. The result use of multipath channel model (disable) was better than using the model (ITU pedestrian A). The value of the throughput at 15 dB was approximately 1600 packet/sec, and at -1 dB was its value 1300 packet/se. According to data, the Multipath channel model of the disable type the value of the MOS was better than the ITU Pedestrian A type.

scholarly journals Indoor Localization System Using Wireless Sensor Network

2018 ◽  
pp. 29-38
Keyword(s):  
Indoor Localization ◽  
Low Cost ◽  
Wide Band ◽  
Human Movement ◽  
Indoor Positioning ◽  
Positioning System ◽  
Wireless System ◽  
Anchor Nodes ◽  
Indoor Positioning System ◽  
Better Than

Building a precise low cost indoor positioning and navigation wireless system is a challenging task. The accuracy and cost should be taken together into account. Especially, when we need a system to be built in a harsh environment. In recent years, several researches have been implemented to build different indoor positioning system (IPS) types for human movement using wireless commercial sensors. The aim of this paper is to prove that it is not always the case that having a larger number of anchor nodes will increase the accuracy. Two and three anchor nodes of ultra-wide band with or without the commercial devices (DW 1000) could be implemented in this work to find the Localization of objects in different indoor positioning system, for which the results showed that sometimes three anchor nodes are better than two and vice versa. It depends on how to install the anchor nodes in an appropriate scenario that may allow utilizing a smaller number of anchors while maintaining the required accuracy and cost.

scholarly journals Sensorless dual axis solar tracker using improved sun position algorithm

2020 ◽  
Vol 11 (3) ◽  
pp. 1305
Author(s):  
Chan Men Loon ◽  
Muhamad Zalani Daud
Keyword(s):  
Low Cost ◽  
Percentage Error ◽  
Total Output ◽  
Solar Pv ◽  
Pv Systems ◽  
Measured Angle ◽  
Solar Tracker ◽  
Fixed Panel ◽  
Fixed System ◽  
Better Than

This paper presents development of a prototype sensorless dual axis solar tracker for maximum extraction of solar energy. To prove the concept and evaluate the proposed algorithm, a low cost widely availabe materials were used which was programmed based on Arduino microcontroller. The porposed algorithm works based on two search methods namely the global search that approximates the best point location in a region, and local search that further determines the actual sun’s position. Experimental results showed that the proposed algorithm gives better performance compared to the existing sun position algorithm (SPA) - based method as well as the fixed panel system. In terms of total output power, the proposed algorithm gives 17.96% more efficient than the fixed system and 6.38% better than the SPA-based system. Furthermore, the percentage error of the experimental measured angle to the actual sun azimuth angle was relatively minimal (less than 3%) during clear day operation. The system was proven to be effective in tracking the sun for improved energy production of solar PV panels and the proposed algorithm also can be used for designing the tracker with larger size of solar PV systems.

Optimizing Convolutional Neural Network Accelerator on Low-Cost FPGA

2021 ◽  
pp. 2150193
Author(s):  
Truong Quang Vinh ◽  
Dinh Viet Hai
Keyword(s):  
Neural Network ◽  
Convolutional Neural Network ◽  
Low Cost ◽  
Optimal Number ◽  
Data Reuse ◽  
Logic Element ◽  
Input Buffer ◽  
Classification Tasks ◽  
Processing Engine ◽  
Better Than

Convolutional neural network (CNN) is one of the most promising algorithms that outweighs other traditional methods in terms of accuracy in classification tasks. However, several CNNs, such as VGG, demand a huge computation in convolutional layers. Many accelerators implemented on powerful FPGAs have been introduced to address the problems. In this paper, we present a VGG-based accelerator which is optimized for a low-cost FPGA. In order to optimize the FPGA resource of logic element and memory, we propose a dedicated input buffer that maximizes the data reuse. In addition, we design a low resource processing engine with the optimal number of Multiply Accumulate (MAC) units. In the experiments, we use VGG16 model for inference to evaluate the performance of our accelerator and achieve a throughput of 38.8[Formula: see text]GOPS at a clock speed of 150[Formula: see text]MHz on Intel Cyclone V SX SoC. The experimental results show that our design is better than previous works in terms of resource efficiency.

scholarly journals Crack Restraining Methods and their Effects on the Microstructures and Properties of Laser Cladded WC/Fe Coatings

Materials ◽  
2018 ◽  
Vol 11 (12) ◽  
pp. 2541 ◽  
Author(s):  
Qiu-Lian Dai ◽  
Can-bin Luo ◽  
Fang-yi You
Keyword(s):  
Wear Resistance ◽  
Laser Cladding ◽  
Low Cost ◽  
Annealing Treatment ◽  
Melting Process ◽  
Laser Cladding Process ◽  
Process Heat ◽  
Crack Susceptibility ◽  
Better Than

Laser cladded WC/Fe coatings have the advantages of low cost and high abrasion wear resistance. However, cracks always appear in WC/Fe coatings, which limits their industrial application. In this paper, the co-effects of the re-melting process, heat treatments, and amount of Co element on the cracking susceptibility, microstructures, and mechanical properties of WC/Fe laser cladding coatings were studied. Experimental results show that re-melting process is helpful to improve the surface quality of the coating and to reduce the cracking susceptibility. The hardness of the coating decreases slightly but distributes more uniformly. Cracks in the coating can be inhibited effectively by preheating the substrate to 250 °C and maintaining the temperature during the laser cladding process, as well as applying an annealing treatment at 300 °C for 1 h. Heat treatment also results in a slight decrease in the hardness. Crack initiation cannot be restrained completely by applying the above two methods when laser cladding a big area of coating. On the basis of the above two methods, addition of Co element to the coating can further improve its toughness and decrease the crack susceptibility. Crack-free WC/Fe coating can be manufactured when 8% Co is added, and its wear resistance is much better than that of the hardened medium steel, especially when the wear time is long.

scholarly journals PROTOTYPE DESIGN OF MICRO HYDRO USING TURBINE ARCHIMEDES SCREW FOR SIMULATION OF HIDROPOWER PRACTICAL OF ELECTRO ENGINEERING STUDENTS

2019 ◽  
Vol 3 (1) ◽  
pp. 6
Author(s):  
Antonius Ibi Weking ◽  
Yanu Prapto Sudarmojo
Keyword(s):  
Energy Source ◽  
Power Plants ◽  
Engineering Students ◽  
Low Cost ◽  
Water Pressure ◽  
Water Discharge ◽  
Small Scale ◽  
Engineering Department ◽  
Influence Of Water ◽  
Turbine Speed

Development of new and renewable energy source always developed by world researchers which one of those is energy source from water, because it’s friendly for environment and low cost. Water is one of energy source which it’s have big potential in all Indonesian territory. The main problem from microhydropower plants is a water discharge which it’s flow is not continued every year because influenced by weather season. Micro Hydro is a microhydro power plants (MHP)in a small scale. A micro hydro can be operated in a certain of time if it has a enough water supply. To knowing a right of micro hydro’s  characteristic is not easy thing to learn it. It is because a characteristic each of micro hydro’s installation location is considered specific location.               One type of micro hydro is using Archimedes Screw Turbine. Udayana University of Electrical Engineering Department in this time not have a facility for hydropower field to use this model, so a college student not yet to receive a knowledge of this. Through this research, a writer want to expand a college student’s knowledge in hydropower field with create a prototype of micro hydro with Archimedes Screw Turbine to hydropower practical in laboratory. In this research the effect of screw’s height angle conversion and effect of water pressure conversion has to be researched. In this study will discuss the influence of water pressure and slope of the altitude angle on the rotation produced by the Archimedes screw turbine so that it can be seen the voltage, current, power generated by the generator, torque and efficiency . The result of from handmade equipment for this research in angle 40­0 with biggest generator round (rpm) is 3768 (rpm) and highest power is 10.92057 watt, torque adalah 0.60 Nm dan efisiensi sebesar 14 %. The torque which resulted from water pressure 24 psi is 0,73 Nm and efficience 18,01 %. The voltage, current, and output power which resulted in generator is 85,8 Volt, 0,1963 Ampere and 16,85 Watt. For generator speed round in the pressure 24 Psi is 4582 rpm, while turbine speed round which resulted from the pressure 24 Psi is 383 rpm before coupled with generator and 222 rpm after coupled with generator.

A Lagrangian Model for Irregular Waves and Wave Kinematics

2003 ◽  
Vol 125 (2) ◽  
pp. 94-102 ◽  
Author(s):  
Svein Helge Gjøsund
Keyword(s):  
Iterative Method ◽  
Irregular Waves ◽  
Lagrangian Model ◽  
Surface Zone ◽  
Wave Interactions ◽  
Wave Flume ◽  
Wave Kinematics ◽  
Eulerian Formulation ◽  
The Waves ◽  
Good Agreement

It has proven difficult to describe the kinematics in irregular waves satisfactorily, in particular for the surface zone in broad-banded waves. A Lagrangian approach offers distinct advantages in this respect, eliminating the need for extrapolation of solutions or “stretching” of coordinates. This paper presents a model of irregular waves based on superposition of linear Lagrangian wave components, using an iterative method to obtain the Eulerian solution. This approach yields theoretically consistent results everywhere in the waves, and comparisons with wave flume measurements show good agreement. Also, the linear Lagrangian model includes wave interactions that would be nonlinear in an Eulerian formulation.

Sign in / Sign up

Export Citation Format

Share Document