Phenol adsorption on industrial activated carbon: evaluation of efficiency

2021 ◽  
pp. 49-54
Author(s):  
С.А.А. Ахмед ◽  
Е.С. Гогина
Keyword(s):  
Activated Carbon ◽  
Adsorption Capacity ◽  
High Efficiency ◽  
Freundlich Isotherm ◽  
Isotherm Model ◽  
Maximum Adsorption Capacity ◽  
Phenol Removal ◽  
Ph Variation ◽  
Wide Ph Range ◽  
Coconut Shells

Адсорбция фенола на активированном угле считается одной из наиболее эффективных систем очистки сточных вод. В связи с этим изучена эффективность двух промышленных активированных углей российского производства для очистки сточных вод от фенола. Образцы включают порошкообразный активированный уголь (производимый из березового угля) и дробленый активированный уголь (производимый из скорлупы кокосового ореха). Исследование проведено в условиях изменения pH, влияния времени контакта и различных начальных концентраций фенола на процесс адсорбции. Исследование дополнительно расширено для выяснения кинетики адсорбции и модели изотерм Ленгмюра и Фрейндлиха. Результаты показали, что активированный уголь сохраняет максимальную адсорбционную способность в широком диапазоне pH – от 2 до 9. Это доказывает применимость угля для удаления фенола из различных сточных вод. Механизм адсорбции с использованием обоих образцов активированных углей следовал псевдовторому порядку и соответствовал модели изотермы Ленгмюра. Максимальная адсорбционная способность составила 185,19 и 172,41 мг/г для порошкообразного и дробленого угля соответственно, что свидетельствует о высокой эффективности удаления фенола из сточных вод. The adsorption of phenol on activated carbon is considered one of the most efficient wastewater treatment systems. In this regard, the effectiveness of two Russian manufactured industrial activated carbon types in removing phenol from wastewater has been studied. The samples included powdered activated carbon (made from birch charcoal) and crushed activated carbon (made from coconut shells). The study was carried out under the conditions of pH variation and the effect of contact time and different initial concentrations of phenol on the adsorption process. The study was further expanded to clarify the adsorption kinetics and the Langmuir and Freundlich isotherm model. The results showed that activated carbon retained the maximum adsorption capacity over a wide pH range of 2 to 9. This fact proves the usability of coal for removing phenol from various wastewater types. The adsorption mechanism using both activated carbon samples followed the pseudo-second order and corresponded to the Langmuir isotherm model. The maximum adsorption capacity was 185.19 and 172.41 mg/g for powdered and crushed coal, respectively, suggesting a high efficiency of phenol removal from wastewater.

Application of Carbonaceous Materials to Phenol Removal from Aqueous Solution by Adsorption

2012 ◽  
Vol 164 ◽  
pp. 297-301 ◽  
Author(s):  
Wei Fang Dong ◽  
Li Hua Zang ◽  
Qing Chao Gong ◽  
Cun Cun Chen ◽  
Cai Hong Zheng ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Adsorption Capacity ◽  
Petroleum Coke ◽  
Granular Activated Carbon ◽  
Powdered Activated Carbon ◽  
Maximum Adsorption Capacity ◽  
Phenol Removal ◽  
Carbonaceous Materials ◽  
Solution Ph ◽  
Equilibrium Studies

Low cost carbonaceous materials were evaluated for their ability to remove phenol from wastewater. The effects of adsorbents dosage, contact time and maximum adsorption capacity were investigated for granular activated carbon, powdered activated carbon, petroleum coke and multi-walled carbon nanotube (MWNT). Equilibrium studies were conducted in 50mg/L initial phenol concentration, solution pH of 5 and at temperature of 23°C. The results showed the adsorption process was fast and it reached equilibrium in 3 h. Petroleum coke and MWNT had poor adsorption which could reach the removal efficiency of phenol with 43.18% and 36.64% respectively. The granular activated carbon possessed good adsorption ability to phenol with 96.40% at the optimum dosage 5g and optimum time 90min.The powdered activated carbon was an effective adsorbent with a maximum adsorption capacity of 42.32 mg/g.

Adsorption of chromium (VI) from aqueous solutions on activated carbon

1994 ◽  
Vol 30 (9) ◽  
pp. 191-197 ◽  
Author(s):  
R. Leyva Ramos ◽  
A. Juarez Martinez ◽  
R. M. Guerrero Coronado
Keyword(s):  
Activated Carbon ◽  
Adsorption Isotherm ◽  
Adsorption Capacity ◽  
Ph Effect ◽  
Freundlich Isotherm ◽  
Maximum Adsorption Capacity ◽  
Experimental Adsorption ◽  
Ph Values ◽  
Chromium Vi ◽  
Adsorption Data

The adsorption isotherm of chromium (VI) on activated carbon was obtained in a batch adsorber. The experimental adsorption data were fitted reasonably well to the Freundlich isotherm. The effect of pH on the adsorption isotherm was investigated at pH values of 4, 6, 7, 8, 10 and 12. It was found that at pH < 6, Cr(VI) was adsorbed and reduced to Cr(III) by the catalytic action of the carbon and that at pH ≥ 12, Cr(VI) was not adsorbed on activated carbon. Maximum adsorption capacity was observed at pH 6 and the adsorption capacity was diminished about 17 times by increasing the pH from 6 to 10. The pH effect was attributed to the different complexes that Cr(VI) can form in aqueous solution. The adsorption isotherm was also affected by the temperature since the adsorption capacity was increased by raising the temperature from 25 to 40°C. It was concluded that Cr(VI) was adsorbed significantly on activated carbon at pH 6 and that the adsorption capacity was greatly dependent upon pH.

Adsorption of cadmium(II) from aqueous solution onto activated carbon

1997 ◽  
Vol 35 (7) ◽  
pp. 205-211 ◽  
Author(s):  
R. Leyva-Ramos ◽  
J. R. Rangel-Mendez ◽  
J. Mendoza-Barron ◽  
L. Fuentes-Rubio ◽  
R. M. Guerrero-Coronado
Keyword(s):  
Activated Carbon ◽  
Adsorption Isotherm ◽  
Adsorption Capacity ◽  
Freundlich Isotherm ◽  
Carbon Surface ◽  
Maximum Adsorption Capacity ◽  
Solution Ph ◽  
Ph Values ◽  
Average Percent Deviation ◽  
Initial Ph

The adsorption isotherm of cadmium on activated carbon was measured in a batch adsorber. Effects of temperature and solution pH on the adsorption isotherm were investigated by determining the adsorption isotherm at temperatures of 10, 25, and 40°C and at initial pH values from 2 to 8. Langmuir isotherm better fitted the experimental data since the average percent deviation was lower than with the Freundlich isotherm It was noticed that the amount of Cd2+ adsorbed was reduced about 3 times by increasing the temperature from 10 to 40°C. It was found that Cd2+ was not adsorbed on activated carbon at pH of 2 or lower and that Cd2+ was precipitated out as Cd(OH)2 at pH values above 9. Maximum adsorption capacity was observed at pH of 8 and the adsorption capacity was decreased about 12 times by reducing the initial pH from 8 to 3. According to the cadmium speciation diagram the predominant species below pH of 8 is Cd2+. Thus, cadmium was adsorbed on the activated carbon surface as Cd2+. It was concluded that the adsorption capacity is a strong function of pH and temperature.

Synthesis and evaluation of activated carbon/nanoclay/ thiolated graphene oxide nanocomposite for lead(II) removal from aqueous solution

2019 ◽  
Vol 79 (3) ◽  
pp. 466-479 ◽  
Author(s):  
Fatemeh Mojoudi ◽  
Amir Hossein Hamidian ◽  
Yu Zhang ◽  
Min Yang
Keyword(s):  
Graphene Oxide ◽  
Activated Carbon ◽  
Adsorption Capacity ◽  
Isotherm Model ◽  
Bet Surface Area ◽  
Polluted Water ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
High Adsorption ◽  
Fast Kinetics

Abstract Novel porous nanocomposite (AC/NC/TGO) was successfully synthesized through the composition of activated carbon, nanoclay and graphene oxide as a Pb(II) adsorbent for the treatment of contaminated aqueous environment. The physicochemical properties and morphology of AC/NC/TGO were examined by Fourier transform infrared spectroscopy, X-ray diffraction, scanning electron microscopy and nitrogen adsorption-desorption techniques. Results showed Pb(II) adsorption on the AC/NC/TGO was rapid in the first 20 min and reached equilibrium in 40 min. Kinetic studies showed significant fit to the pseudo second order kinetic model (R2 ≥ 0.9965) giving an equilibrium rate constant (K2) of 0.0017 g mg−1 min−1 for Pb(II) loaded. The experimental adsorption data were better fitted with the Langmuir isotherm model than with the Freundlich isotherm model. Prepared nanocomposite exhibited high values of Brunauer–Emmett–Teller (BET) surface area of 1,296 m2 g−1 and total pore volume of 1.01 cm3 g−1. Maximum adsorption capacity (Qmax = 208 mg g−1) and a relatively high adsorption rate was achieved at pH 5.0 using an adsorbent dose of 0.5 g L−1 and an initial lead concentration of 50 mg L−1. High adsorption capacity, reusability, fast kinetics and simple synthesis method indicate that prepared nanocomposite can be suggested as a high-performance adsorbent for Pb(II) removal from polluted water.

scholarly journals Langmuir and Freundlich isotherm equation test on the adsorption process of Cu (II) metal ions by cassava peel waste (Manihot esculenta crantz)

2021 ◽  
Vol 2126 (1) ◽  
pp. 012022
Author(s):  
S Nuryanti ◽  
Suherman ◽  
S Rahmawati ◽  
M Amalia ◽  
T Santoso ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Adsorption Capacity ◽  
Manihot Esculenta ◽  
Contact Time ◽  
Adsorption Process ◽  
Freundlich Isotherm ◽  
Maximum Adsorption Capacity ◽  
Manihot Esculenta Crantz ◽  
Isotherm Equations ◽  
Cassava Peel

Abstract This Study aims to determine the adsorption process of Cu (II) metal by cassava peel waste (Manihot esculenta crantz) meeting the Langmuir equation and Freundlich. Research method cassava peel made into activated carbon, then determine the mass, pH and optimum contact time. Then the determination of the maximum adsorption capacity was carried out by testing with the Langmuir isotherm and Freundlich isotherm equations. The results showed that the best conditions (optimal conditions) were obtained with the addition of 0.5 grams of active carbs from cassava peels. The percentage of Cu ion adsorption in these conditions was 97.72%, at pH 6 and a contact time of 60 minutes and the absorption capacity was 98.49%. The maximum adsorption capacity of cassava peel activated carbon to Cu(II) ions at the optimum condition was determined based on the Langmuir and Freundlich isotherm equations. The results obtained were-51.813 mg/g and 26,792 mg/g, respectively.

Removal of Pb(II) Ions from Aqueous Solutions by Spherical Nanocomposites Synthesized Through Immobilization of Paecilomyces lilacinus in Silica Nanoparticles Coated with Ca-Alginate

2020 ◽  
Vol 20 (3) ◽  
pp. 1907-1916
Author(s):  
Xiaofang Ruan ◽  
Ruyi Li ◽  
Zhexu Ding ◽  
Jun Luo ◽  
Qilin Liu ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Silica Nanoparticles ◽  
Adsorption Capacity ◽  
High Efficiency ◽  
Adsorption Process ◽  
Freundlich Isotherm ◽  
Alginate Beads ◽  
Paecilomyces Lilacinus ◽  
Isotherm Models ◽  
Maximum Adsorption Capacity

In the present study, a novel microbial nanocomposite “Paecilomyces lilacinus-silica nanoparticlescalcium-alginate beads” (P. lilacinus-SN-Cal-Alg) were synthesized and their high efficiency for removing Pb(II) ions was demonstrated in aqueous solution. P. lilacinus-SN-Cal-Alg beads before and after the adsorption of Pb(II) were characterized by FT-IR, SEM-EDS, and XPS analyses. The adsorption capacity of Pb(II) by P. lilacinus-SN-Cal-Alg beads was analyzed in aqueous solution. For comparison, the adsorption capacity of Pb(II) by another type of microbial composites, namely, P. lilacinus-Cal-Alg beads, without addition of silica nanoparticles, was also studied in parallel. Lastly, the equilibrium data in adsorption process were examined by both Langmuir and Freundlich isotherm models to evaluate adsorption mechanism. The results showed that an excellent removal efficiency of Pb(II) in aqueous solution (85.54%) was obtained at initial concentration of 200 mg/L by using the P. lilacinus-SN-Cal-Alg beads. Meanwhile, they exhibited the better adsorption capacity for Pb(II) than P. lilacinus-Cal-Alg beads. The adsorption process by P. lilacinus-SN-Cal-Alg beads was best described by the Langmuir model indicating that monolayer adsorption of Pb(II) ions takes place on the beads surfaces and showed that its maximum adsorption capacity was 282.49 mg/g.

scholarly journals Preparation of ureido-functionalized PVA/silica mesoporous fibre membranes via electrospinning for adsorption of Pb2+ and Cu2+ in wastewater

2017 ◽  
Vol 76 (9) ◽  
pp. 2526-2534 ◽  
Author(s):  
Meimei Zhou ◽  
Weizhen Tang ◽  
Pingping Luo ◽  
Jiqiang Lyu ◽  
Aixia Chen ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Adsorption Capacity ◽  
Freundlich Isotherm ◽  
Isotherm Model ◽  
Maximum Adsorption Capacity ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Adsorption Desorption

Abstract Ureido-functionalized mesoporous polyvinyl alcohol/silica composite nanofibre membranes were prepared by electrospinning technology and their application for removal of Pb2+ and Cu2+ from wastewater was discussed. The characteristics of the membranes were investigated by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and N2 adsorption-desorption analysis. Results show that the membranes have long fibrous shapes and worm-like mesoporous micromorphologies. Fourier transform infrared spectroscopy confirmed the membranes were successfully functionalized with ureido groups. Pb2+ and Cu2+ adsorption behavior on the membranes followed a pseudo-second-order nonlinear kinetic model with approximately 30 minutes to equilibrium. Pb2+ adsorption was modelled using a Langmuir isotherm model with maximum adsorption capacity of 26.96 mg g−1. However, Cu2+ adsorption was well described by a Freundlich isotherm model with poor adsorption potential due to the tendency to form chelating complexes with several ureido groups. Notably, the membranes were easily regenerated through acid treatment, and maintained adsorption capacity of 91.87% after five regeneration cycles, showing potential for applications in controlling heavy metals-related pollution and metals reuse.

scholarly journals ADSORPTION OF FOOD COLORING ALLURA RED DYE (E129) FROM AQUEOUS SOLUTIONS USING ACTIVATED CARBON

2017 ◽  
Vol 3 (1) ◽  
pp. 10 ◽  
Author(s):  
Saad A Alkahtani ◽  
Samer S Abu-Alrub ◽  
Ashraf M Mahmoud
Keyword(s):  
Activated Carbon ◽  
Aqueous Solutions ◽  
Adsorption Capacity ◽  
Kinetic Models ◽  
Freundlich Isotherm ◽  
Second Order ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Factors Affecting ◽  
Allura Red

<p>The adsorption behavior of Allura red (E129)<strong> </strong>from aqueous solutions onto activated carbon was successfully investigated. All factors affecting the adsorption process were carefully studied and the conditions were optimized. Adsorption of E129 onto activated carbon was found to increase by decreasing the mass of activated carbon, pH and ionic strength of the solution and by increasing temperature. The adsorption capacity of the activated carbon for Allura red was relatively high. Under the optimum conditions, the maximum adsorption capacity for E129 dye was 72.85 mg/g. Three adsorption models; Langmuir, Freundlich and Temkin model were investigated regarding the adsorption of E129. The models’ parameters K<sub>L</sub>, qm, R2, (n) were determined and found to be 0.0222, 72.85 mg/g, 0.9057-0.9984, and 0.992, respectively. Also, pseudo first and second-order kinetic models were tested to determine the best-fit model to the adsorption of E129 dye onto activated carbon. The results showed that the adsorption of E129 onto activated carbon obeyed both the Freundlich isotherm and pseudo second-order kinetic models. Moreover, thermodynamic studies indicated that the adsorption of E129 dye onto the activated carbon was spontaneous. </p>

scholarly journals Isolasi Kitosan Dari Tudung Jamur Merang (Vollvariella Volvaceae) Dan Aplikasinya Sebagai Absorben Logam Timbal (Pb)

2018 ◽  
Vol 6 (1) ◽  
pp. 44-50
Author(s):  
Matheis F.J.D.P. Tanasale ◽  
Adriani Bandjar ◽  
Natasya Sewit
Keyword(s):  
Experimental Data ◽  
Molecular Weight ◽  
Adsorption Capacity ◽  
Langmuir Isotherm ◽  
Freundlich Isotherm ◽  
Isotherm Model ◽  
Maximum Adsorption Capacity ◽  
Langmuir Isotherm Model ◽  
Ftir Spectrophotometry ◽  
Chitin And Chitosan

Chitosan isolated from mushroom (Vollariella volvaceae) as adsorbent of lead (Pb) metal has been done.  The isolation of chitosan was obtained 2.94% from total weight of mushroom.  Fungtional groups of chitin and chitosan were indentified by using FTIR spectrophotometry.  The chitosan had 74.66% degree of deacetylation and 2.09 x 104 g/mol viscosity molecular weight.  The experimental data of the chitosan as adsorbent for Pb metal were correlated with the Langmuir and Freundlich isotherm model.  The maximum adsorption capacity of Pb based on the Langmuir isotherm model was 2.66 mg/g.

scholarly journals Parametric Statistical Significance of Iron (II) Ions Adsorption by Coconut Shell in Aqueous Solutions

2019 ◽  
Vol 11 (1) ◽  
pp. 17-25
Author(s):  
Babatope Abimbola Olufemi ◽  
Anne Nlerum
Keyword(s):  
Aqueous Solutions ◽  
Adsorption Capacity ◽  
Contact Time ◽  
Statistical Significance ◽  
Freundlich Isotherm ◽  
Coconut Shell ◽  
Isotherm Model ◽  
Maximum Adsorption Capacity ◽  
Order Kinetic ◽  
Sorption Data

The parametric statistical adsorption of chemically unmodified coconut shell powder (CSP) to adsorb iron (II) ions from aqueous solutions was examined in this work. It was observed that the adsorption capacity increased with increasing adsorbent dose, reducing adsorbate dose, increasing contact time, decreasing temperature and reducing particle size. As observed about one gram of the adsorbent was sufficient enough to remove 98 % iron (II) ions. A total contact time of about 40 minutes was sufficient for almost complete adsorption of the ions, while a pH of about 6.0 exhibited the maximum adsorption capacity. The sorption data were fitted into Langmuir, Freundlich, Temkin and the Dubinin-Radushkevich isotherms, fitted most with the Freundlich Isotherm model. The energy values obtained from the Temkin and Dubinin-Radushkevich isotherm model indicated high chemisorption phenomenon with the adsorbents. Investigation of some kinetic models confirmed that the adsorption of iron (II) ions using CSP was a pseudo-second order kinetic process, which further corroborates that chemisorption dominates the adsorption. Fourier Transform Analysis (FTIR) further established and justified the outcome of the study. The adsorption was parametrically justified statistically with Analysis of Variance (ANOVA) and Bonferroni-Holm Posthoc significance test. Conclusively, coconut shell proved strongly to be an effective and suitable adsorbent for removing iron (II) ions from aqueous solutions.

Sign in / Sign up

Export Citation Format

Share Document