scholarly journals Concrete Pavement Mixtures with High Supplementary Cementitious Materials Content: Volume 3

2021 ◽  
Author(s):  
M. Ley ◽  
◽  
Zane Lloyd ◽  
Shinhyu Kang ◽  
Dan Cook ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Particle Distribution ◽  
Isothermal Calorimetry ◽  
Content Volume ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Unit Weight ◽  
Performance Predictions ◽  
Automated Scanning

Fly ash is a by-product of coal combustion, made up of particles that are collected through various methods. This by-product has been used successfully as a partial Portland cement replacement in concrete, but the performance predictions of fly ash in concrete have been difficult to predict, especially at high fly ash replacement rates. This study focuses on comparing the performance of concrete with a variety of fly ash mixtures as well as the particle distribution and chemical makeup of fly ash. The slump, unit weight, compressive strength, and isothermal calorimetry tests were used to measure the performance of concrete at 0%, 20%, and 40% fly ash replacement levels. The particle distribution of fly ash was measured with an automated scanning electron microscope. Additionally, the major and minor oxides from the chemical makeup of fly ash were measured for each mixture and inputted into a table. The particle distribution and chemical makeup of fly ash were compared to the performance of slump, unit weight, compressive strength, isothermal calorimetry, and surface electrical resistivity.

scholarly journals Key Factors Determining the Self-Healing Ability of Cement-Based Composites with Mineral Additives

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4211
Author(s):  
Kamil Tomczak ◽  
Jacek Jakubowski ◽  
Łukasz Kotwica
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Crack Width ◽  
Defect Formation ◽  
Cementitious Materials ◽  
The Self ◽  
Supplementary Cementitious Materials ◽  
Self Healing ◽  
Key Factors ◽  
Important Indicator

This paper reveals the relationships between key factors that determine the ability of cementitious composites to self-heal autogenously and specific measures for quantifying the effects of this process. The following material factors: water-to-binder ratio (w/b), uniaxial compressive strength and age of the composite at the time of defect formation were considered, as well as the method and degree of damage to the tested material. The subjects of this study were mortars and concretes in which Portland cement was partially replaced, to varying degrees, with mechanically activated fluidized bed combustion fly ash (MAFBC fly ash) and siliceous fly ash. The samples were subjected to three-point bending or cyclic compression tests after 14 or 28 days of aging, in order to induce defects and then cured in water for 122 days. Microscopic (MO) and high-resolution scanning (HRS) observations along with computer image processing techniques were used to visualize and quantify the changes occurring in the macro-crack region near the outer surface of the material during the self-sealing process. Techniques based on the measurement of the ultrasonic pulse velocity (UPV) allowed the quantification of the changes occurring inside the damaged materials. Mechanical testing of the composites allowed quantification of the effects of the activity of the binder-supplementary cementitious materials (SCMs) systems. The analysis of the results indicates a significant influence of the initial crack width on the ability to completely close the cracks; however, there are repeated deviations from this rule and local variability of the self-sealing process. It has been shown that the compressive strength of a material is an important indicator of binder activity concerning crack width reduction due to self-sealing. Regardless of the crack induction method, the internal material changes caused by self-sealing are dependent on the degree of material damage.

scholarly journals Comparison of the influence of silica-rich supplementary cementitious materials on cement mortar composites: Mechanical and microstructural assessment

2021 ◽  
Author(s):  
Ozer Sevim ◽  
Cagrı Goktug Sengul
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Cement Mortar ◽  
Bottom Ash ◽  
Cementitious Materials ◽  
Maximum Strength ◽  
Supplementary Cementitious Materials ◽  
Microstructural Properties ◽  
Cement Production ◽  
Mechanical And Microstructural Properties

Abstract The silica-rich supplementary cementitious materials (SCMs) are the key components of mechanical and microstructural properties. The use of SCMs results in improving the mechanical and microstructural properties and decreasing the environmental burden caused by cement production. In this regard, this paper reports a study to compare the influence of silica-rich supplementary cementitious materials (slag, fly ash, and bottom ash) having similar Blaine fineness on cement mortar composites in terms of mechanical and microstructural properties. First, supplementary cementitious materials (slag, fly ash, and bottom ash) were ground at similar cement Blaine fineness (~ 3300 cm2/g) and then by replacing 5% and 20% with cement, the 7-, 28-, 90-day mechanical and microstructural properties of cement mortar composites incorporating SCMs were examined. As a result, it was observed that the compressive strength and microstructural properties of cement mortar composites incorporating slag gave maximum strength and microstructural properties according to samples with fly ash and bottom ash having similar fineness and this will decrease the required amount of cement for the target properties by using slag, thus the number of CO2 emitted to nature will also decrease.

Durability of Sustainable Self-Consolidating Concrete

2018 ◽  
Vol 765 ◽  
pp. 285-289
Author(s):  
Osama Ahmed Mohamed ◽  
Waddah Al Hawat ◽  
Omar Fawwaz Najm
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Silica Fume ◽  
Cementitious Materials ◽  
Chloride Penetration ◽  
Supplementary Cementitious Materials ◽  
Test Results ◽  
Self Consolidating Concrete ◽  
Human Footprint ◽  
Granulated Blast Furnace Slag

Supplementary cementitious materials such as fly ash, silica fume and ground granulated blast furnace slag (GGBS) have been used widely to partially replace cement in producing self-consolidating concrete (SCC). The production of cement is associated with emission of significant amounts of CO2 and increases the human footprint on the environment. Fly ash, silica fume, and GGBS are recycled industrial by-products that also impart favorable fresh and hardened properties on concrete. This study aims to assess the effect of the amounts of fly ash and silica fume on strength and chloride penetration resistance of concrete. Rapid Chloride Penetration Test (RCPT) was used to assess the ability of SCC to resist ingress of chlorides into concrete. SCC mixes with different dosages of fly ash and silica fume were developed and tested at different curing ages. Test results showed that replacing 20% of cement with fly ash produced the highest compressive strength of 67.96 MPa among all fly ash-cement binary mixes. Results also showed that replacing15% of cement with silica fume produced the highest compressive strength of 95.3 MPa among fly ash-cement binary mixes. Using fly ash and silica fume consistently increased the concrete resistance to chloride penetration at the early ages. Silica fume at all dosages results in low or very low levels of chloride penetration at all curing ages of concrete.

Tentative Optimum Proportion of Supplementary Cementitious Materials in Blended Cement to Perform Better under Tannery Wastewater

2018 ◽  
Vol 937 ◽  
pp. 107-113
Author(s):  
Samina Samrose ◽  
Saifa Anzum ◽  
Samira Mahmud ◽  
Tanvir Manzur
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Blended Cement ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Effluent Treatment ◽  
Tannery Wastewater ◽  
Wastewater Sample ◽  
Supplementary Cementitious Material ◽  
Optimum Proportion

The present research studies the compressive strength of cement mortar cubes prepared from different proportions of supplementary cementitious materials (Fly Ash and Slag) in blended cement. This research aims to find the tentative optimum composition of supplementary cementitious material that shows better performance under tannery wastewater condition, such as that in effluent treatment plants. Synthetic tannery wastewater was simulated in laboratory after collecting wastewater sample from local tannery industry. Eight types of cement compositions (varying supplementary materials proportions) have been chosen. Compressive strength test has been conducted on mortar cubes over a period of three months. Test results revealed that slag addition had shown significantly stronger effects than that of fly ash addition. Also, the combined effect of fly ash and slag and their order of variation on strength were studied. The observations made from this research will be helpful for selection of blended cement proportions in future structures exposed to similar severe conditions.

scholarly journals Physical and Mechanical Properties of High-Strength Concrete Modified with Supplementary Cementitious Materials after Exposure to Elevated Temperature up to 1000 °C

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 532 ◽  
Author(s):  
Jianwei Zhou ◽  
Dong Lu ◽  
Yuxuan Yang ◽  
Yue Gong ◽  
Xudong Ma ◽  
...  
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Physical Properties ◽  
Water Absorption ◽  
High Strength Concrete ◽  
Elevated Temperatures ◽  
High Strength ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Strength Concrete

This paper presents the experimental findings of a study on the influence of combining usage of supplementary cementitious materials (SCMs) on the performance of high-strength concrete (HSC) subjected to elevated temperatures. In this study, four types of HSC formulations were prepared: HSC made from cement and fly ash (FA), HSC made from cement and ultra-fine fly ash (UFFA), HSC made from cement and UFFA-metakaolin (MK), and HSC made from cement and FA-UFFA-MK. Mechanical and physical properties of HSC subjected to high temperatures (400, 600, 800, and 1000 °C) were studied. Furthermore, the relation between residual compressive strength and physical properties (loss mass, water absorption, and porosity) of HSC was developed. Results showed that the combined usage of SCMs had limited influence on the early-age strength of HSC, while the 28-d strength had been significantly affected. At 1000 °C, the residual compressive strength retained 18.7 MPa and 23.9 MPa for concretes containing 30% UFFA-5% MK and 10% FA-20% UFFA-5% MK, respectively. The specimen containing FA-UFFA-MK showed the best physical properties when the temperature raised above 600 °C. Combined usage of SCMs (10% FA-20% UFFA-5% MK) showed the lowest mass loss (9.2%), water absorption (10.9%) and porosity (28.6%) at 1000 °C. There was a strongly correlated relation between residual strength and physical properties of HSC exposed to elevated temperatures.

scholarly journals Feasibility of Using Biomass Fly Ash in Cementitious Materials

Proceedings ◽  
2019 ◽  
Vol 34 (1) ◽  
pp. 12
Author(s):  
Jonathan Page ◽  
Laurent Libessart ◽  
Chafika Djelal ◽  
Maurice Gonon ◽  
Issam Laiymani
Keyword(s):  
Fly Ash ◽  
Portland Cement ◽  
Water Demand ◽  
Isothermal Calorimetry ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Wood Biomass ◽  
Fly Ashes ◽  
X Ray ◽  
Biomass Fly Ash

In recent years, numerous studies focused on the development of sustainable cement-based binders through the use of supplementary cementitious materials such slag, fly ash, metakaolin, silica fume, pozzolan, etc. The use of wood biomass for power generation is increasingly common which lead to an important amount of waste produced in the combustion process such as fly ash, which must be transported to landfills for deposition, or used as sludge in farming. Depending on their chemical and physical characteristics, wood biomass fly ashes could be reuse in blended cements as supplementary cementitious material. Different sources of biomass fly ashes have been selected to evaluate their potential for use as a cement replacement. Their chemical and mineralogical compositions, as well as their morphology were first evaluated via X-ray and laser diffraction (XRD), inductively coupled plasma (ICP) and scanning electron microscopy (SEM coupled with energy-dispersive X-ray spectroscopy (EDX). Fly ashes showed variable physicochemical characteristics but some present interesting compositions for the intended use. One fly ash present a high content of CaO and minors of SiO2 and Al2O3. The chemical composition does not allow to categorize this fly ash as a pozzolan material but it may have a latent hydraulic behaviour, which could be interesting as cement substitution. This fly ash has been incorporated into a cement paste by progressive replacement of Portland cement (from 0 to 70%). It has been observed that biomass fly ash has a higher water demand compared to Portland cement. This additional water demand was evaluated by the Vicat consistency test and by an evaporometry method. The setting time and kinetic hydration of the biomass fly ash pastes were also assessed with the standardized Vicat test and by isothermal calorimetry.

scholarly journals The Influence and Application of Slag, Fly Ash, and Limestone Flour on Compressive Strength of Concrete Based on the Concrete Compressive Strength Development over Time (CCSDOT) Model

2020 ◽  
Vol 10 (10) ◽  
pp. 3572
Author(s):  
Jian Zheng ◽  
Guohua Liu
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Strength Development ◽  
Mix Proportion ◽  
Practical Engineering ◽  
Compressive Strength Development ◽  
Compressive Strength Of Concrete ◽  
Selection Of

Concrete and cement have been widely used in past decades as a result of urbanization. More and more supplementary cementitious materials are adopted in concrete because its production complements environmental conservation. The influence of slag, fly ash, limestone, etc., on compressive strength of concrete is of interest to engineers worldwide. Many previous studies were specific to certain engineering or certain experiments that could not reveal the nature of the influence of the three supplementary cementitious materials on concrete’s compressive strength. The research concerning the influence of two or more kinds of supplementary cementitious materials on concrete’s compressive strength is still unclear. Moreover, there is a lack of clarity on the optimum proportion of one or more certain cementitious materials in practical engineering or experiments. To overcome these problems, this study adopts the concrete compressive strength development over time (CCSDOT) model, which generates an explicit formula to conduct quantitative research based on extensive data. The CCSDOT model performs well in fitting the compressive strength development of concrete containing cement, slag, fly ash, and limestone flour. The results reveal the nature of the influence of the three supplementary cementitious materials on concrete’s compressive strength through the parameter analysis in the model. Two application cases are analyzed concerning the selection of the three supplementary cementitious materials and design of concrete mix proportion for practical engineering. It is concluded that the CCSDOT model and the method in this study can possibly provide guidance on both the selection of supplementary cementitious materials and the design of optimal concrete mix proportion for practical engineering. Therefore, the study is highly essential and useful.

scholarly journals Compressive Strength of Concrete using Fly Ash and Rice Husk Ash: A Review

2020 ◽  
Vol 6 (7) ◽  
pp. 1400-1410
Author(s):  
Joel Sam
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Concrete Strength ◽  
Cementitious Materials ◽  
Supplementary Cementitious Materials ◽  
Partial Replacement ◽  
Compressive Strength Of Concrete ◽  
Minor Compounds

Decreasing our over-reliance on cement as an ingredient in the making of concrete due to its contribution to the CO2 emissions has led to numerous researches been conducted to find suitable replacement for cement in concrete mixes.  Materials like fly ash, ground granulated blast furnace slag, silica fume, rice husk ash and metakaolin among others have been identified as materials that can at the very least be used as a replacement for cement in concrete mix. These materials are referred to as supplementary cementitious materials (SCMs). This paper reviewed the work that has been done on the use of fly ash and rice husk ash as partial replacements for concrete, its chemical composition and its effect on the compressive strength of concrete. Charts, tables and figures were employed as tools to study the various chemical compounds of fly ash and rice husk ash. It was seen that depending on how the coal or rice husk was initially processed the percentage of some of the minor compounds like Sodium oxide (Na2O), Titanium oxide (TiO2) and Phosphorus pentoxide (P2O5) were sometimes very low or not recorded as part of the final product.  The data on the compressive strength of concrete after fly ash and rice husk ash had been added in percentage increments of 0%, 10%, 20%, 30%, 40%, 50% and 0%, 5%, 7.5%, 10%, 12.5%, 15% respectively analysed over a minimum period of 7 days and a maximum period of 28 days found out that the optimal percentage partial replacement of fly ash and rice husk ash for a strong compressive concrete strength is 30% of fly ash and 7.5% of rice husk ash.

scholarly journals Energy Savings Associated with the Use of Fly Ash and Nanoadditives in the Cement Composition

Energies ◽  
2020 ◽  
Vol 13 (9) ◽  
pp. 2184 ◽  
Author(s):  
Grzegorz Ludwik Golewski
Keyword(s):  
Tensile Strength ◽  
Compressive Strength ◽  
Fly Ash ◽  
Plain Concrete ◽  
Cementitious Materials ◽  
Splitting Tensile Strength ◽  
Environmental Benefits ◽  
Supplementary Cementitious Materials ◽  
Mechanical Parameters ◽  
Concrete Mix

The paper presented herein investigates the effects of using supplementary cementitious materials (SCMs) in quaternary mixtures on the compressive strength and splitting tensile strength of plain concrete. In addition, environmental benefits resulting from the proposed solutions were analysed. A total of four concrete mixtures were designed, having a constant water/binder ratio of 0.4 and total binder content of 352 kg/m3. The control mixture only contained ordinary Portland cement (OPC) as binder, whereas others incorporated quaternary mixtures of: OPC, fly ash (FA), silica fume (SF), and nanosilica (nS). Based on the obtained test results, it was found that concretes made on quaternary binders containing nanoadditives have very favorable mechanical parameters. The quaternary concrete containing: 80% OPC, 5% FA, 10% SF, and 5% nS have shown the best results in terms of good compressive strength and splitting tensile strength, whereas the worst mechanical parameters were characterized by concrete with more content of FA additive in the concrete mix, i.e., 15%. Moreover, the results of compressive strength and splitting tensile strength are qualitatively convergent. Furthermore, reducing the amount of OPC in the composition of the concrete mix in quaternary concretes causes environmental benefits associated with the reduction of: raw materials that are required for burning clinker, electricity, and heat energy in the production of cement.

Sign in / Sign up

Export Citation Format

Share Document