scholarly journals Experimental Analysis on Mechanical Properties of Natural Bio-Polymer Composite

2021 ◽  
Vol 16 (1) ◽  
pp. 012-017
Author(s):  
Sudalai Raja A ◽  
Jebakani D
Keyword(s):  
Mechanical Properties ◽  
Low Cost ◽  
Neem Oil ◽  
Testing Methods ◽  
Medical Field ◽  
Natural Resin ◽  
Tensile Impact ◽  
Sporting Goods ◽  
Screw Pine ◽  
Bio Material

Bio-composites are used in many engineering applications due to various desirable properties that they offer such as light weight, low cost, bio-degradable and bio-compatible. Bio-composites are used in many industries such as automotive, sporting goods, marine, electrical and household appliances. Kenaf, jute, banana, flux is used as fibers. The mechanical properties are evaluated by appropriate testing methods. The strength of material is important to each material so that bio-material to be evaluated by mechanical testing methods. In this study an attempt is made to prepare natural resin with neem oil and Thennamarakudi oil and to fabricate Bio-composite with fish shell and screw pine fiber as reinforcement and test for its mechanical properties such as tensile, Impact and Flexural. The pure resin samples have tensile and flexible properties. After taken testing. the neem oil-based biomaterial flexibility is higher than the oil-based biomaterial. The stiffness is higher in Tk oil-based biomaterial. The result is expected from the biomaterial as eco-friendly material and applicable for medical field as biocompatible

Mechanical Property Studies on Flax Fiber Reinforced Basalt Powder Filled Polyester Composite

2020 ◽  
Vol 13 ◽  
Author(s):  
V. Arumugaprabu ◽  
K.Arun Prasath ◽  
S. Mangaleswaran ◽  
M. Manikanda Raja ◽  
R. Jegan
Keyword(s):  
Mechanical Properties ◽  
Mechanical Property ◽  
Natural Fiber ◽  
Tensile Load ◽  
Flax Fiber ◽  
Flexural Properties ◽  
Weight Percentage ◽  
Tensile Impact ◽  
Polyester Composite ◽  
Additional Support

: The objective of this research is to evaluate the tensile, impact and flexural properties of flax fiber and basalt powder filled polyester composite. Flax fiber is one of the predominant reinforcement natural fiber which possess good mechanical properties and addition of basalt powder as a filler provides additional support to the composite. The Composites are prepared using flax fiber arranged in 10 layers with varying weight percentage of the basalt powder as 5 wt.%, 10 wt.%, 15 wt.%, 20 wt.%, 25 wt.% and 30 wt.% respectively. From the results it is inferred that the composite combination 10 Layers of flax / 5 wt.%, basalt Powder absorbs more tensile load of 145 MPa. Also, for the same combination maximum flexural strength is about 60 MPa. Interestingly in the case of impact strength more energy was absorbed by 10 layers of flax and 30 wt.% of basalt powder. In addition, the failure mechanism of the composites also discussed briefly using SEM studies.

scholarly journals Physical and Mechanical Properties of Natural Leaf Fiber-Reinforced Epoxy Polyester Composites

Polymers ◽  
2021 ◽  
Vol 13 (9) ◽  
pp. 1369
Author(s):  
Sanjeev Kumar ◽  
Lalta Prasad ◽  
Vinay Kumar Patel ◽  
Virendra Kumar ◽  
Anil Kumar ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Composite Materials ◽  
Synthetic Fibre ◽  
Low Cost ◽  
Fibre Length ◽  
Physical And Mechanical Properties ◽  
Natural Fibres ◽  
Risk Environment ◽  
Insulation Property ◽  
Natural Leaf

In recent times, demand for light weight and high strength materials fabricated from natural fibres has increased tremendously. The use of natural fibres has rapidly increased due to their high availability, low density, and renewable capability over synthetic fibre. Natural leaf fibres are easy to extract from the plant (retting process is easy), which offers high stiffness, less energy consumption, less health risk, environment friendly, and better insulation property than the synthetic fibre-based composite. Natural leaf fibre composites have low machining wear with low cost and excellent performance in engineering applications, and hence established as superior reinforcing materials compared to other plant fibres. In this review, the physical and mechanical properties of different natural leaf fibre-based composites are addressed. The influences of fibre loading and fibre length on mechanical properties are discussed for different matrices-based composite materials. The surface modifications of natural fibre also play a crucial role in improving physical and mechanical properties regarding composite materials due to improved fibre/matrix adhesion. Additionally, the present review also deals with the effect of silane-treated leaf fibre-reinforced thermoset composite, which play an important role in enhancing the mechanical and physical properties of the composites.

scholarly journals Mimicking the Mechanical Properties of Aortic Tissue with Pattern-Embedded 3D Printing for a Realistic Phantom

Materials ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 5042
Author(s):  
Jaeyoung Kwon ◽  
Junhyeok Ock ◽  
Namkug Kim
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
3D Printing ◽  
Mechanical Characteristics ◽  
Aortic Wall ◽  
Tensile Tests ◽  
Human Aorta ◽  
Aortic Tissue ◽  
Medical Field ◽  
Base Materials

3D printing technology has been extensively applied in the medical field, but the ability to replicate tissues that experience significant loads and undergo substantial deformation, such as the aorta, remains elusive. Therefore, this study proposed a method to imitate the mechanical characteristics of the aortic wall by 3D printing embedded patterns and combining two materials with different physical properties. First, we determined the mechanical properties of the selected base materials (Agilus and Dragonskin 30) and pattern materials (VeroCyan and TPU 95A) and performed tensile testing. Three patterns were designed and embedded in printed Agilus–VeroCyan and Dragonskin 30–TPU 95A specimens. Tensile tests were then performed on the printed specimens, and the stress-strain curves were evaluated. The samples with one of the two tested orthotropic patterns exceeded the tensile strength and strain properties of a human aorta. Specifically, a tensile strength of 2.15 ± 0.15 MPa and strain at breaking of 3.18 ± 0.05 mm/mm were measured in the study; the human aorta is considered to have tensile strength and strain at breaking of 2.0–3.0 MPa and 2.0–2.3 mm/mm, respectively. These findings indicate the potential for developing more representative aortic phantoms based on the approach in this study.

Heat Treatment Effects on Static and Dynamic Mechanical Properties of Sintered SINT D30 Powder Metal

2013 ◽  
Vol 592-593 ◽  
pp. 643-646 ◽  
Author(s):  
Marko Šori ◽  
Tomaž Verlak ◽  
Srečko Glodež
Keyword(s):  
Mechanical Properties ◽  
Complex Geometry ◽  
Low Cost ◽  
Surface Hardness ◽  
Load Ratio ◽  
Tensile Tests ◽  
Test Machine ◽  
Strain Diagram ◽  
Powder Metal ◽  
Sintered Steel

Low cost, low material waste and good accuracy in components with complex geometry are the main reasons for powder metallurgy to be considered as a promising manufacturing process for the future. Like wrought steel, sintered steel can also be heat treated to increase surface hardness and to improve strength. This paper compares mechanical properties of the hardened sintered steel with the sintered steel of the same powder metal SINT D30. Firstly, the static strength of both samples is determined by quasi-static tensile tests. Results are compared in stress strain diagram and they show that the tensile strength of the hardened sintered steel SINT D30 can surpass 700 MPa. The main focus of this study is however fatigue behaviour of the sintered steel. Both sets of samples are tested on a pulsating test machine with the load ratio of R = 0. The first sample is subjected to a load that corresponds to 90 % of the yield strength and is then gradually lowered to achieve one million stress cycles without breakage. Obtained results are then presented as Wöhler curves and compared in S-N diagram.

scholarly journals Effect of Intercalation Structure of Organo-Modified Montmorillonite/Polylactic Acid on Wheat Straw Fiber/Polylactic Acid Composites

Polymers ◽  
2018 ◽  
Vol 10 (8) ◽  
pp. 896 ◽  
Author(s):  
Qiqi Fan ◽  
Guangping Han ◽  
Wanli Cheng ◽  
Huafeng Tian ◽  
Dong Wang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Thermogravimetric Analysis ◽  
Wheat Straw ◽  
Polylactic Acid ◽  
Low Cost ◽  
Interlayer Spacing ◽  
Positive Influence ◽  
X Ray Diffraction ◽  
Ft Ir ◽  
Ir Analysis

In this work, an easy way to prepare the polylactic acid (PLA)/wheat straw fiber (WSF) composite was proposed. The method involved uses either the dopamine-treated WSF or the two-step montmorillonite (MMT)-modified WSF as the filler material. In order to achieve the dispersibility and exfoliation of MMT, it was modified by 12-aminododecanoic acid using a two-step route. X-ray diffraction (XRD) and scanning electron microscopy (SEM) were performed to characterize the modified MMT and the coated WSF. As for the properties of PLA/WSF composites, some thermal (using Fourier transform infrared spectroscopy (FT-IR) and thermogravimetric analysis) and mechanical properties (flexural, tensile, and impact) were analyzed. The results showed that the dopamine was successfully coated onto the WSF. Furthermore, Na-MMT was successfully transformed to organo-montmorillonite (OMMT) and formed an exfoliated structure. In addition, a better dispersion of MMT was obtained using the two-step treatment. The interlayer spacing of modified MMT was 4.06 nm, which was 123% higher than that of the unmodified MMT. Additionally, FT-IR analysis suggested that OMMT diffused into the PLA matrix. The thermogravimetric analysis (TGA) showed that a higher thermal stability of PLA/WSF composites was obtained for the modified MMT and dopamine. The results also showed that both the dopamine treated WSF and the two-step-treated MMT exhibited a positive influence on the mechanical properties of PLA/WSF composites, especially on the tensile strength, which increased by 367% compared to the unmodified precursors. This route offers researchers a potential scheme to improve the thermal and mechanical properties of PLA/WSF composites in a low-cost way.

scholarly journals The Effect of Heat Treatment on the Microstructure and Mechanical Properties of the Novel Low-Cost Ti-3Al-5Mo-4Cr-2Zr-1Fe Alloy

Materials ◽  
2020 ◽  
Vol 13 (17) ◽  
pp. 3798
Author(s):  
Meng Sun ◽  
Dong Li ◽  
Yanhua Guo ◽  
Ying Wang ◽  
Yuecheng Dong ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Aging Time ◽  
Volume Fraction ◽  
Low Cost ◽  
Solution Treatment ◽  
Solution Temperature ◽  
The Novel ◽  
Α Phase ◽  
The Cost

In order to reduce the cost of titanium alloys, a novel low-cost Ti-3Al-5Mo-4Cr-2Zr-1Fe (Ti-35421) titanium alloy was developed. The influence of heat treatment on the microstructure characteristics and mechanical properties of the new alloy was investigated. The results showed that the microstructure of Ti-35421 alloy consists of a lamina primary α phase and a β phase after the solution treatment at the α + β region. After aging treatment, the secondary α phase precipitates in the β matrix. The precipitation of the secondary α phase is closely related to heat treatment parameters—the volume fraction and size of the secondary α phase increase when increasing the solution temperature or aging time. At the same solution temperature and aging time, the secondary α phase became coarser, and the fraction decreased with increasing aging temperature. When Ti-35421 alloy was solution-treated at the α + β region for 1 h with aging surpassing 8 h, the tensile strength, yield strength, elongation and reduction of the area were achieved in a range of 1172.7–1459.0 MPa, 1135.1–1355.5 MPa, 5.2–11.8%, and 7.5–32.5%, respectively. The novel low-cost Ti-35421 alloy maintains mechanical properties and reduces the cost of materials compared with Ti-3Al-5Mo-5V-4Cr-2Zr (Ti-B19) alloy.

Pseudoelasticity of Cu-13.8Al-Ni Alloys Containing V and Nb

2008 ◽  
Vol 59 ◽  
pp. 101-107 ◽  
Author(s):  
Rodinei Medeiros Gomes ◽  
Ana Cris R. Veloso ◽  
V.T.L. Buono ◽  
Severino Jackson Guedes de Lima ◽  
Tadeu Antonio de Azevedo Melo
Keyword(s):  
Mechanical Properties ◽  
Shape Memory ◽  
Shape Recovery ◽  
Cold Water ◽  
Low Cost ◽  
Tensile Tests ◽  
Grain Refiner ◽  
Good Shape ◽  
Potential Applications ◽  
Superelastic Behavior

Polycrystalline copper-based shape memory alloys have been of particular interest in relation to Ni-Ti because of their low cost and good shape memory effect. Nevertheless the absence of a pronounced pseudoelasticity effect restricts the number of potential applications. In this work, the influence of Nb and V on the microstructure and the mechanical properties was investigated. Samples of Cu-13.8 Al-Ni containing V and Nb alloy were prepared by induction and solution treated at 850°C and then further quenched into cold water. The addition of Nb and V promotes the formation of precipitates which act as grain refiner and subsequently improve the mechanical properties. The tensile tests were performed at temperatures slightly inferior to Mf and superior to Af, to investigate the shape recovery and pseudoelasticity, respectively. Based on the analyses of the Cu-13,8Al-2Ni-1Nb (wt%) alloy was detected rupture strains greater than 14%, besides observation of the superelasticity of these alloys and quantification of this property by means of cycling, from 0 to strains between 1 and 7%. The studies performed on alloy Cu-13.8Al- 3,5Ni-1V (wt%) made it possible to determine rupture strains in the order of 3% and its superelastic behavior through cycling for deformations between 1 and 3%.

scholarly journals Effect of T6 Heat Treatment Parameters on Technological Quality of the AlSi7Mg Alloy

2016 ◽  
Vol 16 (4) ◽  
pp. 95-100 ◽  
Author(s):  
J. Pezda ◽  
A. Jarco
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Low Cost ◽  
Dispersion Hardening ◽  
Recycling Potential ◽  
Low Mass ◽  
Technological Quality ◽  
New Applications ◽  
Casting Design

Abstract Very well-known advantages of aluminum alloys, such as low mass, good mechanical properties, corrosion resistance, machining-ability, high recycling potential and low cost are considered as a driving force for their development, i.e. implementation in new applications as early as in stage of structural design, as well as in development of new technological solutions. Mechanical and technological properties of the castings made from the 3xx.x group of alloys depend mainly on correctly performed processes of melting and casting, design of a mould and cast element, and a possible heat treatment. The subject-matter of this paper is elaboration of a diagrams and dependencies between parameters of dispersion hardening (temperatures and times of solutioning and ageing treatments) and mechanical properties obtained after heat treatment of the 356.0 (EN AC AlSi7Mg) alloy, enabling full control of dispersion hardening process to programming and obtaining a certain technological quality of the alloy in terms of its mechanical properties after performed heat treatments. Obtained results of the investigations have enabled obtainment of a dependencies depicting effect of parameters of the solutioning and ageing treatments on the mechanical properties (Rm, A5 and KC impact strength) of the investigated alloy. Spatial diagrams elaborated on the basis of these dependencies enable us to determine tendencies of changes of the mechanical properties of the 356.0 alloy in complete analyzed range of temperature and duration of the solutioning and ageing operations.

Sign in / Sign up

Export Citation Format

Share Document