Sorption of Heavy Metal on Natural Clay

2018 ◽  
Vol 68 (12) ◽  
pp. 2804-2807
Author(s):  
Mircea Stefan ◽  
Adriana Bors ◽  
Daniela Simina Stefan ◽  
Ionut Alexandru Savu Radu ◽  
Cicerone Marinescu
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Metal Ion ◽  
Background Electrolyte ◽  
Hydroxyl Groups ◽  
Natural Clay ◽  
Equilibrium Isotherms ◽  
Solution Ph ◽  
Constant Ph ◽  
Langmuir Isotherm Model

Sorption of heavy metals on Na-montmorillonite was studied as a function of solution pH and different concentrations of background electrolyte and also a function of added metal ion at constant pH. Equilibrium isotherms have been measured and analyzed using a Langmuir isotherm model. The metal ions were predominantly adsorbed on the permanent charge sites in a easily replaceable state. There was also evident a substantial involvement of the hydroxyl groups on the edges of Na-montmorillonite in specific adsorption of the cations especially at higher pH.

scholarly journals Plant-Based Tacca leontopetaloides Biopolymer Flocculant (TBPF) Produced High Removal of Heavy Metal Ions at Low Dosage

Processes ◽  
2020 ◽  
Vol 9 (1) ◽  
pp. 37
Author(s):  
Nurul Shuhada Mohd Makhtar ◽  
Juferi Idris ◽  
Mohibah Musa ◽  
Yoshito Andou ◽  
Ku Halim Ku Hamid ◽  
...  
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Metal Ions ◽  
Metal Ion ◽  
Metal Removal ◽  
Test Procedure ◽  
Synthetic Wastewater ◽  
Leachate Treatment ◽  
Low Concentration ◽  
Removal Of Heavy Metals

High removal of heavy metals using plant-based bioflocculant under low concentration is required due to its low cost, abundant source, and nontoxicity for improved wastewater management and utilization in the water industry. This paper presents a treatment of synthetic wastewater using plant-based Tacca leontopetaloides biopolymer flocculant (TBPF) without modification on its structural polymer chains. It produced a high removal of heavy metals (Zn, Pb, Ni, and Cd) at a low concentration of TBPF dosage. In our previous report, TBPF was characterized and successfully reduced the turbidity, total suspended solids, and color for leachate treatment; however, its effectiveness for heavy metal removal has not been reported. The removal of these heavy metals was performed using a standard jar test procedure at different pH values of synthetic wastewater and TBPF dosages. The effects of hydroxide ion, pH, initial TBPF concentration, initial metal ion concentration, and TBPF dosage were examined using one factorial at the time (OFAT). The results show that the highest removal for Zn, Pb, Ni, and Cd metal ions were 98.4–98.5%, 79–80%, 97–98%, and 92–93%, respectively, using 120 mg/L dosage from the initial concentration of 10% TBPF at pH 10. The final concentrations for Zn, Pb, Ni, and Cd metal ions were 0.043–0.044, 0.41–0.43, 0.037–0.054, and 0.11–0.13 mg/L, respectively, which are below the Standard B discharge limit set by the Department of Environment (DOE), Malaysia. The results show that TBPF has a high potential for the removal of heavy metals, particularly Zn, Pb, Ni, and Cd, in real wastewater treatment.

Migration Patterns of Heavy Metals in Soil in Wastewater Irrigation Area in the Suburb of Eastern Inner Mongolia

2011 ◽  
Vol 343-344 ◽  
pp. 340-343
Author(s):  
Ri Cha Hu ◽  
Li Bo Sun
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Inner Mongolia ◽  
Metal Ion ◽  
Vertical Direction ◽  
Heavy Metal Concentration ◽  
Water Shortage ◽  
Wastewater Irrigation ◽  
Irrigation Area ◽  
Eastern Inner Mongolia

Based on the soil test of heavy metals in wastewater irrigation area in eastern Inner Mongolia, this paper analyses the content of heavy metals Cr, Cu, Cd, Pb in different layers of soil samples and reveals the internal relations between heavy metal concentration gradient in the vertical direction and soil properties, thus providing a scientific basis to guide sewage irrigation, solve the problem of water shortage in wastewater irrigation area and carry out environmental impact assessment. Soil is an important subsystem in natural environmental systems, through which many pollutants, especially heavy metals, produced by human activities, enter the food chain and ultimately do harm to human health. Currently, heavy metal ion contamination to the soil caused by wastewater irrigation has become one of the focuses in the study of soil chemistry and agricultural environment pollution. For this reason, it is particularly important to study the migration mechanism of heavy metals in soil and to provide a reliable theoretical basis for the prevention and management of soil contaminants.

scholarly journals (3-Aminopropyl) Triethoxysilane (APTES) Functionalized Magnetic Nanosilica Graphene Oxide (MGO) Nanocomposite for the Comparative Adsorption of the Heavy Metal (Pb(II), Cd(II) and Ni(II)) ions from Aqueous Solution

2021 ◽  
Author(s):  
C Donga ◽  
S Mishra ◽  
A Aziz ◽  
L Ndlovu ◽  
A Kuvarega ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Graphene Oxide ◽  
Metal Ion ◽  
Ion Concentration ◽  
Batch Adsorption ◽  
Solution Ph ◽  
Magnetic Graphene Oxide ◽  
Equilibrium Data ◽  
Langmuir Isotherm Model ◽  
Adsorption Equilibrium Data

Abstract (3-aminopropyl) triethoxysilane (APTES) modified magnetic graphene oxide was synthesized and applied in the adsorption of three heavy metals, Pb(II), Cd(II) and Ni(II) from aqueous solution. An approach to prepare magnetic GO was adopted by using (3-aminopropyl) triethoxysilane (APTES) as a functionalizing agent on magnetic nanosilica coupled with GO to form the Fe3O4@SiO2-NH2/GO nanocomposite. FT-IR, XRD, BET, UV, VSM, SAXS, SEM and TEM were used to characterize the synthesized nanoadsorbents. Batch adsorption studies were conducted to investigate the effect of solution pH, initial metal ion concentration, adsorbent dosage and contact time. The maximum equilibrium time was found to be 30 min for Pb(II), Cd(II) and 60 min for Ni(II). The kinetics studies showed that the adsorption of Pb(II), Cd(II) and Ni(II) onto Fe3O4@SiO2-NH2/GO followed the pseudo-second-order kinetics. All the adsorption equilibrium data were well fitted to Langmuir isotherm model and maximum monolayer adsorption capacity for Pb(II), Cd(II) and Ni(II) were 13.46, 18.58 and 13.52 mgg-1, respectively. The Fe3O4@SiO2-NH2/GO adsorbents were reused for at least 7 cycles without the leaching of mineral core, showing the enhanced stability and potential application of Fe3O4@SiO2-NH2/GO adsorbents in water/wastewater treatment.

scholarly journals pH-Regulated Carbon Dots Fluorescence Sensor Array Detection of Multiple Heavy Metal Ions Under Stepwise Prediction

2022 ◽  
Author(s):  
Zijun Xu ◽  
Yuying Liu ◽  
Jiao Chen ◽  
Xiyuan Wang ◽  
Hao Liu ◽  
...  
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Metal Ions ◽  
Metal Ion ◽  
Heavy Metal Ions ◽  
Sensor Array ◽  
Chelating Agent ◽  
Fluorescence Sensor ◽  
Array Detection ◽  
Multiple Heavy Metals

Abstract As a large amount of heavy metals leaches into water sources from industrial effluents, heavy metal pollution has become an important factor affecting water quality. To enable the detection of multiple heavy metals, we constructed a pH-regulation fluorescence sensor array. Firstly, by adding a metal chelating agent as receptor, metal ions and carbon quantum dots (CDs) were connected to distinguish between Cr6+, Fe3+, Fe2+, and Hg2+ ions. Thus, the lack of affinity between the indicator functional groups and the analyte was solved. Secondly, by adjusting the pH environment of the solution system, an economical and simple array sensing platform is established, which effectively simplified the array construction. In this study, the SX-model was used in the field of fluorescence sensor array detection for metal ion recognition. Based on the strategy of stepwise prediction, combined with the classification and concentration models, the bottleneck of the unified model in previous studies was broken. This sensor array demonstrated sensitive detection of four heavy metal ions within a concentration range from 1 to 50 µM, with an accuracy of 95.45%. Moreover, it displayed the ability to efficiently identify binary mixed samples with an accuracy of 95.45%. Furthermore, metal ions in 15 real samples (lake water) were effectively discriminated with 100% accuracy. A chelating agent was used to improve the sensitivity of heavy metal ion detection and eventually led to high-precision prediction using the SX-model.

scholarly journals Adsorption of Cr(VI) Ions using Activated Carbon Produced from Indian Water Chestnut (Trapa natans) Peel Powder

2020 ◽  
Vol 32 (4) ◽  
pp. 876-880
Author(s):  
Maninder Singh ◽  
D. P. Tiwari ◽  
Mamta Bhagat
Keyword(s):  
Heavy Metals ◽  
Metal Ions ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Metal Ion ◽  
Ion Concentration ◽  
Solution Ph ◽  
Indian Water ◽  
Trapa Natans

The indiscriminate discharge of heavy metals into water and soil from anthropogenic practices is becoming prominent threat to the environment. Heavy metals like chromium, cadmium, lead, arsenic, nickel etc. are heavily toxic and carcinogenic in nature. This study emphasizes the adequacy of activated water chest nut (Trapa natans) peel powder as a new adsorbent material for removal of chromium(VI) metal ions. Adsorption experiments were performed in batch process. Various process parameters like contact time, temperature, solution pH, dose of adsorbent, metal ion concentration etc. were optimized. The physico-chemical properties of adsorbent material were characterized by FTIR and XRD. The morphology, topology of adsorbent surface was characterized by scanning electron microscopy (SEM) and Brunauer, Emmett and Teller (BET) which revealed a highly porous structure and available specific surface area. The adsorption capacity (maximum) was counted as 59.17 mg/g and specific surface area was found 23.467 m2/g at a pH 7. The adsorption process for Cr(VI) ions was in a good agreement with Langmuir isotherm. The process also followed pseudo second order kinetics. The obtained result shows that activated water chest nut (Trapa natans) peel powder (AWCPP) can be a hopeful low-cost and eco-friendly bio-adsorbent for removal of Cr(VI) metal ions and also better adsorbent than other various reported adsorbents.

scholarly journals Biosorption and Bioaccumulation Abilities of Actinomycetes/Streptomycetes Isolated from Metal Contaminated Sites

Separations ◽  
2018 ◽  
Vol 5 (4) ◽  
pp. 54 ◽  
Author(s):  
Ivana Timková ◽  
Jana Sedláková-Kaduková ◽  
Peter Pristaš
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Metal Ion ◽  
Polluted Soil ◽  
Negative Effects ◽  
Wide Range ◽  
Specific Uptake ◽  
High Concentrations ◽  
Further Development ◽  
Soil And Water

Heavy metal pollution is of great concern. Due to expansion of industrial activities, a large amount of metal is released into the environment, disturbing its fragile balance. Conventional methods of remediation of heavy metal-polluted soil and water are expensive and inefficient. Therefore, new techniques are needed to provide environmentally friendly and highly selective remediation. Streptomycetes, with their unique growth characteristics, ability to form spores and mycelia, and relatively rapid colonization of substrates, act as suitable agents for bioremediation of metals and organic compounds in polluted soil and water. A variety of mechanisms could be involved in reduction of metals in the environment, e.g., sorption to exopolymers, precipitation, biosorption and bioaccumulation. Studies performed on biosorption and bioaccumulation potential of streptomycetes could be used as a basis for further development in this field. Streptomycetes are of interest because of their ability to survive in environments contaminated by metals through the production of a wide range of metal ion chelators, such as siderophores, which provide protection from the negative effects of heavy metals or specific uptake for specialized metabolic processes. Many strains also have the equally important characteristic of resistance to high concentrations of heavy metals.

Research on Metal Ion Removal of Ceramic Printing Wastewater

2013 ◽  
Vol 664 ◽  
pp. 369-373 ◽  
Author(s):  
Ling Ling Shang ◽  
Ce Shi ◽  
Yong Li Zhang ◽  
Yong Min Liu
Keyword(s):  
Heavy Metal ◽  
Metal Ions ◽  
Metal Ion ◽  
Removal Rate ◽  
Iron Removal ◽  
Reaction Cell ◽  
Solution Ph ◽  
Flame Atomic Absorption ◽  
Removal Of Metal ◽  
Removal Of Metal Ions

The removal of the metal ions in the ceramic printing wastewater was influenced by using, stirring and precipitating of the solution pH, coagulant PAC, coagulant aid PAM and heavy metal scavenger. This experiment investigated the removal effect of the metal ions in the wastewater under different conditions. Flame atomic absorption spectrometry was adopted for the determination of the concentration of metal ions in the wastewater. The studies have shown that alkalization, PAC coagulation treatment have a role in the removal of metal ions in the ceramic printing wastewater. And the chromium and iron removal rate can reached 74.0% and 61.6% respectively. Heavy metal scavenger also have a better role in the removal of metal ions. And the chromium and iron removal rates were 82.3% and 76.2% respectively without dosing PAC. The number of reaction cell has no significant effect on the removal of metal ions.

scholarly journals Isotherm, Kinetics and Thermodynamics of Cu(II) and Pb(II) Adsorption on Groundwater Treatment Sludge-Derived Manganese Dioxide for Wastewater Treatment Applications

2021 ◽  
Vol 18 (6) ◽  
pp. 3050
Author(s):  
Stephanie B. Tumampos ◽  
Benny Marie B. Ensano ◽  
Sheila Mae B. Pingul-Ong ◽  
Dennis C. Ong ◽  
Chi-Chuan Kan ◽  
...  
Keyword(s):  
Heavy Metals ◽  
Metal Ion ◽  
Acid Leaching ◽  
Single Layer ◽  
Toxic Metal ◽  
Ion Concentration ◽  
Groundwater Treatment ◽  
Toxic Heavy Metals ◽  
Solution Ph ◽  
Metal Ion Removal

The ubiquitous occurrence of heavy metals in the aquatic environment remains a serious environmental and health issue. The recovery of metals from wastes and their use for the abatement of toxic heavy metals from contaminated waters appear to be practical approaches. In this study, manganese was recovered from groundwater treatment sludge via reductive acid leaching and converted into spherical aggregates of high-purity MnO2. The as-synthesized MnO2 was used to adsorb Cu(II) and Pb(II) from single-component metal solutions. High metal uptake of 119.90 mg g−1 for Cu(II) and 177.89 mg g−1 for Pb(II) was attained at initial metal ion concentration, solution pH, and temperature of 200 mg L−1, 5.0, and 25 °C, respectively. The Langmuir isotherm model best described the equilibrium metal adsorption, indicating that a single layer of Cu(II) or Pb(II) was formed on the surface of the MnO2 adsorbent. The pseudo-second-order model adequately fit the Cu(II) and Pb(II) kinetic data confirming that chemisorption was the rate-limiting step. Thermodynamic studies revealed that Cu(II) or Pb(II) adsorption onto MnO2 was spontaneous, endothermic, and had increased randomness. Overall, the use of MnO2 prepared from groundwater treatment sludge is an effective, economical, and environmentally sustainable substitute to expensive reagents for toxic metal ion removal from water matrices.

scholarly journals Spatial Relationships Between pH and Vegetation Pattern in an Area Contaminated with Heavy Metals

2003 ◽  
pp. 140-143
Author(s):  
Elza Kovács ◽  
János Tamás
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Plant Species ◽  
Metal Ion ◽  
Toxic Elements ◽  
Vegetation Pattern ◽  
Ion Concentration ◽  
Vegetation Density ◽  
Highly Sensitive ◽  
Ph Conditions

It is not possible to gain information on the risk factor representing the bioavailability and the mobility of the contaminants only on the basis of their total concentrations. Especially, in case of heavy metals, which can be charaterised with very different chemical forms and their mobil and mobilizable parts are determined by complex balances highly sensitive to the changing environmental conditions. Considering mine tailings, however, the toxic elements are basically in ore forms having low adsorption capacity, thus the heavy metal ion concentration in solution is governed mainly by the pH conditions. In Gyöngyösoroszi, the spatial distribution of the total heavy metal concentrations as well as that of pH values determining the bioavailable part of the toxic elements were estimated and by mapping the vegetation pattern, relationship was analysed among the total Zn, Cu, Pb and As concentrations, the pH and the species present. Results show that the presence of the certain plant species is highly determined by the pH on the mine tailing material, the highest vegetation density was found where the bioavailability of the toxic elements were considered the smallest as a result of the neutral pH. As a result, high diversity could be found even in places where the total zinc, copper, lead and arsenic concentrations were extreme. In addition, plant species could be identified, which are tolerant to toxic elements and present even if the pH is low and the bioavailable part of the heavy metals is relatively high.

Sign in / Sign up

Export Citation Format

Share Document