scholarly journals Dirhamnolipid ester – formation of reverse wormlike micelles in a binary (primerless) system

2020 ◽  
Vol 16 ◽  
pp. 2820-2830
Author(s):  
David Liese ◽  
Hans Henning Wenk ◽  
Xin Lu ◽  
Jochen Kleinen ◽  
Gebhard Haberhauer
Keyword(s):  
Alkyl Chain ◽  
Loss Modulus ◽  
Polarized Light ◽  
Maxwell Model ◽  
Wormlike Micelles ◽  
Cole Plot ◽  
Scanning Calorimetry ◽  
Dispersion Energy ◽  
Ester Formation ◽  
Transition Enthalpy

We report new dirhamnolipid ester forming reverse wormlike micelles in nonpolar solvents without the addition of any primer. Therefore, these compounds represent a rare case of a binary system showing this gel-like behavior. In this study, the influence of the concentration of the rhamnolipid ester and the ester alkyl chain length on the rheological properties of the reverse wormlike micelles in toluene was investigated in detail. Highly viscoelastic solutions were obtained even at a relatively low concentration of less than 1 wt %. The phase transition temperatures indicate that the formation of reverse wormlike micelles is favored for dirhamnolipid esters with shorter alkyl chain lengths. Oscillatory shear measurements for the viscoelastic samples reveal that the storage modulus (G') and the loss modulus (G'') cross each other and fit the Maxwell model very well in the low-ω region. As is typical for wormlike micelle systems, the normalized Cole–Cole plot of G''/G'' max against G'/G'' max was obtained as a semicircle centered at G'/G'' max = 1. The formation of network structures was also verified by polarized light microscopy. The sample was birefringent at ambient temperature and anisotropic at an elevated temperature. Differential scanning calorimetry analysis yielded a transition enthalpy of about ΔH SG/GS = ±7.2 kJ/mol. This value corresponds to a strong dispersion energy and explains the formation of the highly viscous gels by the entanglement of wormlike micelles through the interaction of the alkyl chains.

Structure and properties of polypropylene/organic rectorite nanocomposites

Clay Minerals ◽  
2009 ◽  
Vol 44 (1) ◽  
pp. 35-50 ◽  
Author(s):  
Yun Huang ◽  
Xiaoyan Ma ◽  
Guozheng Liang ◽  
Hongxia Yan
Keyword(s):  
Loss Modulus ◽  
Polarized Light ◽  
Clay Content ◽  
Crystal Form ◽  
Ammonium Bromide ◽  
Wide Angle ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Monoclinic Crystal ◽  
X Ray

AbstractMelt blending using a twin-screw extruder was used to prepare composites of polypropylene (PP)/organic rectorite (PR). The organic rectorite (OREC) was modified with dodecyl benzyl dimethyl ammonium bromide (1227). Wide-angle X-ray diffraction (WAXD) and transmission electron microscopy were used to investigate the dispersion of OREC in the composites. The d spacings of OREC in PR composites was greater than in OREC itself. The dispersion of OREC particles in the PP polymer matrix was fine and uniform when the clay content was small (2 wt.%). The rheology was characterized using a capillary rheometer. The processing behaviour of the PR system improved as the amount of OREC added increased. Non-isothermal crystallization kinetics were analysed using differential scanning calorimetry. It was shown that the addition of OREC had a heterogeneous nucleation effect on PP, and can accelerate the crystallization. However, only when fine dispersion was achieved, and at lower rates of temperature decrease, was the crystallinity greater. Wide-angle X-ray diffraction and polarized light microscopy were used to observe the crystalline form and crystallite size. The PP in the PR composites exhibited an a-monoclinic crystal form, as in pure PP, and in both cases a spherulite structure was observed. However, the smaller spherulite size in the PR systems indicated that addition of OREC can reduce the crystal size significantly, which might improve the ‘toughness’ of the PP. The mechanical properties (tensile and impact strength) improved when the amount of OREC added was appropriate. Dynamic mechanical analysis showed that the storage modulus (E′) and loss modulus (E″) of the nanocomposites were somewhat greater than those of pure PP when an appropriate amount of OREC was added. Finally, thermogravimetric analysis showed that the PR systems exhibited a greater thermal stability than was seen with pure PP.

Characterization, liquid crystallinity and spin-coated films of some metalated 1,4,8,11,15,18,22,25-octaalkyl tetrabenzo [b,g,l,q][5,10,15]triazaporphyrin derivatives

2011 ◽  
Vol 15 (09n10) ◽  
pp. 890-897 ◽  
Author(s):  
Andrew N. Cammidge ◽  
Isabelle Chambrier ◽  
Michael J. Cook ◽  
Ernie H.G. Langner ◽  
Muhibur Rahman ◽  
...  
Keyword(s):  
Differential Scanning Calorimetry ◽  
Optical Microscopy ◽  
Alkyl Chain ◽  
Bulk Material ◽  
Polarized Light ◽  
Scanning Calorimetry ◽  
Liquid Crystallinity ◽  
Derivatives Of ◽  
Deposited Films

The preparation and characterization of a number of metalated derivatives of 1,4,8,11,15,18,22,25-octahexyl and 1,4,8,11,15,18,22,25-octadecyl tetrabenzotriazaporphyrins (TBTAPs) are reported. The mesophase behavior of the compounds has been characterized by differential scanning calorimetry (DSC) and by polarized light optical microscopy. Mesophase behavior is compared with data for the corresponding phthalocyanine derivatives reported earlier. The temperature range of the mesophase(s) exhibited by the title compounds is generally broader than those of their phthalocyanine analogs. UV-vis data for examples of the TBTAP compounds as spin-coated films reveal differences in the type of molecular packing in the as-deposited films that is largely dependent upon the length of the alkyl chain substituents. On heating, the films undergo molecular reorganizations at temperatures corresponding to the mesophase transitions of bulk material observed by DSC.

scholarly journals Effect of Nanofiller Content on Dynamic Mechanical and Thermal Properties of Multi-Walled Carbon Nanotube and Montmorillonite Nanoclay Filler Hybrid Shape Memory Epoxy Composites

Polymers ◽  
2021 ◽  
Vol 13 (5) ◽  
pp. 700
Author(s):  
Muhamad Hasfanizam Mat Yazik ◽  
Mohamed Thariq Hameed Sultan ◽  
Mohammad Jawaid ◽  
Abd Rahim Abu Talib ◽  
Norkhairunnisa Mazlan ◽  
...  
Keyword(s):  
Shape Memory ◽  
High Performance ◽  
Loss Modulus ◽  
Decomposition Temperature ◽  
Hybrid Nanocomposites ◽  
Mechanical And Thermal Properties ◽  
Scanning Calorimetry ◽  
Hybrid Filler ◽  
Dynamic Mechanical ◽  
Tan Δ

The aim of the present study has been to evaluate the effect of hybridization of montmorillonite (MMT) and multi-walled carbon nanotubes (MWCNT) on the thermal and viscoelastic properties of shape memory epoxy polymer (SMEP) nanocomposites. In this study, ultra-sonication was utilized to disperse 1%, 3%, and 5% MMT in combination with 0.5%, 1%, and 1.5% MWCNT into the epoxy system. The fabricated SMEP hybrid nanocomposites were characterized via differential scanning calorimetry, dynamic mechanical analysis, and thermogravimetric analysis. The storage modulus (E’), loss modulus (E”), tan δ, decomposition temperature, and decomposition rate, varied upon the addition of the fillers. Tan δ indicated a reduction of glass transition temperature (Tg) for all the hybrid SMEP nanocomposites. 3% MMT/1% MWCNT displayed best overall performance compared to other hybrid filler concentrations and indicated a better mechanical property compared to neat SMEP. These findings open a way to develop novel high-performance composites for various potential applications, such as morphing structures and actuators, as well as biomedical devices.

scholarly journals Crystallization Behavior and Mechanical Properties of Poly(ε-caprolactone) Reinforced with Barium Sulfate Submicron Particles

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2368
Author(s):  
Hegoi Amestoy ◽  
Paul Diego ◽  
Emilio Meaurio ◽  
Jone Muñoz ◽  
Jose-Ramon Sarasua
Keyword(s):  
Barium Sulfate ◽  
Thermal Studies ◽  
Polarized Light ◽  
Optical Microscope ◽  
Submicron Particles ◽  
Degree Of Crystallinity ◽  
Scanning Calorimetry ◽  
Nucleation Effect ◽  
Crystal Fraction ◽  
Light Optical Microscope

Poly(ε-caprolactone) (PCL) was mixed with submicron particles of barium sulfate to obtain biodegradable radiopaque composites. X-ray images comparing with aluminum samples show that 15 wt.% barium sulfate (BaSO4) is sufficient to present radiopacity. Thermal studies by differential scanning calorimetry (DSC) show a statistically significant increase in PCL degree of crystallinity from 46% to 52% for 25 wt.% BaSO4. Non-isothermal crystallization tests were performed at different cooling rates to evaluate crystallization kinetics. The nucleation effect of BaSO4 was found to change the morphology and quantity of the primary crystals of PCL, which was also corroborated by the use of a polarized light optical microscope (PLOM). These results fit well with Avrami–Ozawa–Jeziorny model and show a secondary crystallization that contributes to an increase in crystal fraction with internal structure reorganization. The addition of barium sulfate particles in composite formulations with PCL improves stiffness but not strength for all compositions due to possible cavitation effects induced by debonding of reinforcement interphase.

Study in performance and morphology of polyamide 12 produced by selective laser sintering technology

2018 ◽  
Vol 24 (5) ◽  
pp. 813-820 ◽  
Author(s):  
Junjie Wu ◽  
Xiang Xu ◽  
Zhihao Zhao ◽  
Minjie Wang ◽  
Jie Zhang
Keyword(s):  
Selective Laser Sintering ◽  
Polarized Light ◽  
Chain Scission ◽  
High Energy ◽  
Laser Sintering ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Content Type ◽  
X Ray ◽  
Polyamide 12

Purpose The purpose of this paper is to investigate the effect of selective laser sintering (SLS) method on morphology and performance of polyamide 12. Design/methodology/approach Crystallization behavior is critical to the properties of semi-crystalline polymers. The crystallization condition of SLS process is much different from others. The morphology of polyamide 12 produced by SLS technology was investigated using scanning electron microscopy, polarized light microscopy, differential scanning calorimetry, X-ray diffraction and wide-angle X-ray diffraction. Findings Too low fill laser power brought about bad fusion of powders, while too high energy input resulted in bad performance due to chain scission of macromolecules. There were three types of crystal in the raw powder material, denoted as overgrowth crystal, ring-banded spherulite and normal spherulite. Originality/value In this work, SLS samples with different sintering parameters, as well as compression molding sample for the purpose of comparison, were made to study the morphology and crystal structure of sintered PA12 in detail.

Thermotropic behavior of sodium cholesteryl carbonate

2009 ◽  
Vol 24 (1) ◽  
pp. 156-163 ◽  
Author(s):  
Rabkwan Chuealee ◽  
Timothy S. Wiedmann ◽  
Teerapol Srichana
Keyword(s):  
Phase Behavior ◽  
Chemical Structure ◽  
Liquid Crystalline ◽  
Polarized Light ◽  
Wave Number ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
X Ray Scattering ◽  
C Nmr

Sodium cholesteryl carbonate ester (SCC) was synthesized, and its phase behavior was studied. The chemical structure was assessed by solid-state infrared spectroscopy based on vibration analysis. The wave number at 1705 and 1276 cm−1 corresponds to a carbonyl carbonate and O–C–O stretching of SCC, respectively. Molecular structure of SCC was further investigated with 1H and 13C NMR spectroscopy. The chemical shift, for the carbonyl carbonate resonance appeared at 155.5 ppm. A molecular mass of SCC was at m/z of 452. Differential scanning calorimetry (DSC), video-enhanced microscopy (VEM) together with polarized light microscopy, and small-angle x-ray scattering (SAXS) were used to characterize the phase behavior as a function of temperature of SCC. Liquid crystalline phase was formed with SCC. Based on the thermal properties and x-ray diffraction, it appears that SCC forms a structure analogous to the type II monolayer structure observed with cholesterol esters.

scholarly journals Effects of Pectin on the Physicochemical Properties and Freeze-Thaw Stability of Waxy Rice Starch

Foods ◽  
2021 ◽  
Vol 10 (10) ◽  
pp. 2419
Author(s):  
Yuheng Zhai ◽  
Jiali Xing ◽  
Xiaohu Luo ◽  
Hao Zhang ◽  
Kai Yang ◽  
...  
Keyword(s):  
Physicochemical Properties ◽  
Loss Modulus ◽  
Rice Starch ◽  
Scanning Calorimetry ◽  
Freeze Thaw ◽  
Textural Parameter ◽  
Waxy Rice ◽  
Pasting Temperature ◽  
Starch Paste ◽  
Waxy Rice Starch

In this study, the effects of the addition of pectin (PEC) on the physicochemical properties and freeze-thaw stability of waxy rice starch (WRS) were investigated. As PEC content increased, the pasting viscosity and pasting temperature of WRS significantly increased (p < 0.05), whereas its breakdown value and setback value decreased. Differential scanning calorimetry showed that the addition of PEC increased the gelatinization temperature of WRS, but decreased its gelatinization enthalpy. Rheological measurements indicated that the addition of PEC did not change the shear-thinning behavior of WRS–PEC blends, and the storage modulus and loss modulus were positively correlated with PEC content. Moreover, the textural parameter of WRS decreased with the increase in PEC content. Furthermore, the addition of PEC decreased the transmittance of starch paste, but enhanced the freeze-thaw stability of WRS to some extent. These results may contribute to the development of WRS-based food products.

scholarly journals Stearic Acid, Beeswax and Carnauba Wax as Green Raw Materials for the Loading of Carvacrol into Nanostructured Lipid Carriers

2020 ◽  
Vol 10 (18) ◽  
pp. 6267
Author(s):  
Juliana G. Galvão ◽  
Raquel L. Santos ◽  
Ana Amélia M. Lira ◽  
Renata Kaminski ◽  
Victor H. Sarmento ◽  
...  
Keyword(s):  
Stearic Acid ◽  
Essential Oils ◽  
Antioxidant Activities ◽  
Polarized Light ◽  
Lipid Nanoparticles ◽  
Nanostructured Lipid Carriers ◽  
Chemical Degradation ◽  
Thymus Vulgaris ◽  
Scanning Calorimetry ◽  
Carnauba Wax

The use of lipid nanoparticles as drug delivery systems has been growing over recent decades. Their biodegradable and biocompatible profile, capacity to prevent chemical degradation of loaded drugs/actives and controlled release for several administration routes are some of their advantages. Lipid nanoparticles are of particular interest for the loading of lipophilic compounds, as happens with essential oils. Several interesting properties, e.g., anti-microbial, antitumoral and antioxidant activities, are attributed to carvacrol, a monoterpenoid phenol present in the composition of essential oils of several species, including Origanum vulgare, Thymus vulgaris, Nigellasativa and Origanum majorana. As these essential oils have been proposed as the liquid lipid in the composition of nanostructured lipid carriers (NLCs), we aimed at evaluating the influence of carvacrol on the crystallinity profile of solid lipids commonly in use in the production of NLCs. Different ratios of solid lipid (stearic acid, beeswax or carnauba wax) and carvacrol were prepared, which were then subjected to thermal treatment to mimic the production of NLCs. The obtained binary mixtures were then characterized by thermogravimetry (TG), differential scanning calorimetry (DSC), small angle X-ray scattering (SAXS) and polarized light microscopy (PLM). The increased concentration of monoterpenoid in the mixtures resulted in an increase in the mass loss recorded by TG, together with a shift of the melting point recorded by DSC to lower temperatures, and the decrease in the enthalpy in comparison to the bulk solid lipids. The miscibility of carvacrol with the melted solid lipids was also confirmed by DSC in the tested concentration range. The increase in carvacrol content in the mixtures resulted in a decrease in the crystallinity of the solid bulks, as shown by SAXS and PLM. The decrease in the crystallinity of lipid matrices is postulated as an advantage to increase the loading capacity of these carriers. Carvacrol may thus be further exploited as liquid lipid in the composition of green NLCs for a range of pharmaceutical applications.

scholarly journals Mesomorphism behaviour and photoluminescent properties of new asymmetrical 1,2-di(4-alkoxybenzylidene)hydrazines

2019 ◽  
Vol 43 (1-2) ◽  
pp. 67-77 ◽  
Author(s):  
Adil A Awad ◽  
Al-Ameen Bariz OmarAli ◽  
Ahmed Jasim M Al-Karawi ◽  
Zyad Hussein J Al-Qaisi ◽  
Samer Ghanim Majeed
Keyword(s):  
Differential Scanning Calorimetry ◽  
Liquid Crystal ◽  
Liquid Crystalline ◽  
Polarized Light ◽  
Luminescent Properties ◽  
Scanning Calorimetry ◽  
Crystalline Materials ◽  
X Ray ◽  
Step Procedure ◽  
Liquid Crystalline Materials

{1-[4-( n-Alkoxy)]-2-(4’-decyloxy)benzylidene}hydrazines ( n-alkoxy = O(CH2) nH, n = 1–9, 12, 16 or 18), an asymmetrical series of 1,2-disubstituted hydrazines, were prepared in a simple two-step procedure as a part of our continuing work in evaluating hydrophobic azine compounds as photoluminescent liquid crystalline materials. The compounds were characterized spectroscopically and their liquid crystalline behaviour and luminescent properties were evaluated using polarized light optical microscopy, differential scanning calorimetry and X-ray powder diffraction techniques. The studies revealed that all of these compounds are liquid crystalline materials exhibiting photoluminescent properties in the crystalline and liquid crystal states.

scholarly journals Non-Isothermal Crystallization Kinetics of Injection Grade PHBV and PHBV/Carbon Nanotubes Nanocomposites Using Isoconversional Method

2020 ◽  
Vol 4 (2) ◽  
pp. 52
Author(s):  
Thaís Larissa do Amaral Montanheiro ◽  
Beatriz Rossi Canuto de Menezes ◽  
Larissa Stieven Montagna ◽  
Cesar Augusto Gonçalves Beatrice ◽  
Juliano Marini ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Crystallization Kinetics ◽  
Isothermal Crystallization ◽  
Model Fitting ◽  
Polarized Light ◽  
Isoconversional Method ◽  
Degree Of Crystallinity ◽  
Gamma Aminobutyric Acid ◽  
Scanning Calorimetry ◽  
Kinetics Of

Carbon nanotubes (CNT)-reinforced polymeric composites are being studied as promising materials due to their enhanced properties. However, understanding the behavior of polymers during non-isothermal crystallization is important once the degree of crystallinity and crystallization processes are affected when nanoparticles are added to matrices. Usually, crystallization kinetics studies are performed using a model-fitting method, though the isoconversional method allows to obtain the kinetics parameter without assuming a crystallization model. Therefore, in this work, CNTs were oxidized (CNT-Ox) and functionalized with gamma-aminobutyric acid (GABA) (CNT-GB) and incorporated into a poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) matrix. The influence of the addition and functionalization of CNT in the crystallization kinetics of PHBV was evaluated using the isoconversional method with differential scanning calorimetry (DSC), and by polarized light optical microscopy (PLOM) and Shore D hardness. The incorporation and functionalization of CNT into PHBV matrix did not change the Šesták and Berggren crystallization model; however, the lowest activation energy was obtained for the composite produced with CNT-GB, suggesting a better dispersion into the PHBV matrix. PLOM and Shore D hardness confirmed the results obtained in the kinetics study, showing the smallest crystallite size for CNT-containing nanocomposites and the highest hardness value for the composite produced with CNT-GB.

Sign in / Sign up

Export Citation Format

Share Document