scholarly journals Thermal stability of polyurethane coating prepared by using diphenylolpropane

2020 ◽  
Vol 62 (4) ◽  
pp. 81-87
Author(s):  
Indira N. Bakirova ◽  
Keyword(s):  
Thermal Stability ◽  
Thermal Decomposition ◽  
Weight Loss ◽  
Elevated Temperatures ◽  
Onset Temperature ◽  
Phenolic Hydroxyl ◽  
Hydroxyl Groups ◽  
Polyurethane Coating ◽  
Urethane Group ◽  
Thermal Stability Of

Thermal stability of polyurethane varnish coating prepared by using diphenylolpropane, polyetherpolyol and polyisocyanate with an equimolar ratio of isocyanate and hydroxyl groups was assessed in the air. The polyurethane weight loss thermogram shows three temperature regions: I – (217-275)°С, II – (275-380)°С, and III – above 380°С. For interpreting thermogram of the polyurethane under study the model substances simulating the urethane groups of a polymer were synthesized. The substance containing the urethane group formed by phenolic hydroxyl of diphenylolpropane was shown to demonstrate relatively low thermal stability and gets broken down into isocyanate and bisphenol. Decomposition of the substance containing the urethane group formed by alcoholic hydroxyl occurs at the higher temperature. The data obtained allow interpreting the occurrence of thermal decomposition step I in TGA curve by structural changes in the blocks formed by diphenylolpropane and polyisocyanate being the least stable when exposed to elevated temperatures. The next step can be attributed to decomposition of more thermostable urethane groups formed by functional groups of oligooxypropylenetriol and polyisocyanate. Transition to the step III accompanied by severe sample weight loss due to decomposition of urethane groups is explained by thermal oxidation of oligoether units of polymer. Based on the data obtained the conclusion was made that the presence of urethane groups formed by phenolic hydroxyl of diphenylolpropane in polymer structure results in the decreased thermooxidative decomposition onset temperature of polymer. At the same time, a deceleration of thermooxidative processes due to the stabilizing effect of diphenylolpropane released at the beginning of thermal decomposition of polyurethane is observed in a high-temperature region. The proposed polyurethane coating is inferior to commercial counterparts in thermal decomposition onset temperature but superior to them in the temperature corresponding to a 50% polymer weight loss.

Thermal Stability of Polyurethane Coating Prepared by Using Diphenylolpropane

2021 ◽  
Vol 899 ◽  
pp. 739-744
Author(s):  
Indira N. Bakirova ◽  
Svetlana E. Mitrofanova
Keyword(s):  
Thermal Stability ◽  
Temperature Region ◽  
Polymer Structure ◽  
Phenolic Hydroxyl ◽  
Polyurethane Coating ◽  
Thermooxidative Degradation ◽  
Stabilizing Effect ◽  
Varnish Coating ◽  
Higher Temperature ◽  
Thermal Stability Of

Thermal stability on air of polyurethane varnish coating prepared from diphenylolpropane, polyetherpolyol and polyisocyanate was assessed. The presence of urethane groups, formed by phenolic hydroxyl of diphenylolpropane, in the polymer structure was shown to decrease its thermooxidative degradation onset temperature. At the same time, deceleration of thermooxidative processes due to stabilizing effect of diphenylolpropane released at the beginning of thermal decay of polyurethane is observed in the higher temperature region.

Non-Isothermal Decomposition Kinetic of Polypropylene/Hydrotalcite Composite

2019 ◽  
Vol 19 (11) ◽  
pp. 7493-7501 ◽  
Author(s):  
Sheng Xu ◽  
Min Zhang ◽  
Siyu Li ◽  
Moyu Yi ◽  
Shigen Shen ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Thermal Decomposition ◽  
Nitrogen Atmosphere ◽  
Heating Rates ◽  
Decomposition Reactions ◽  
Kinetic And Thermodynamic Parameters ◽  
Málek Method ◽  
Boundary Reaction ◽  
Phase Boundary Reaction ◽  
Thermal Stability Of

P3O5-10 pillared Mg/Al hydrotalcite (HTs) as a functional fire-retarding filler was successfully prepared by impregnation-reconstruction, where the HTs was used to prepare polypropylene (PP) and HTs composite (PP/HTs). Thermal decomposition was crucial for correctly identifying the thermal behavior for the PP/HTs, and studied using thermogravimetry (TG) at different heating rates. Based on single TG curves and Málek method, as well as 41 mechanism functions, the thermal decompositions of the PP/HTs composite and PP in nitrogen atmosphere were studied under non-isothermal conditions. The mechanism functions of the thermal decomposition reactions for the PP/HTs composite and PP were separately “chemical reaction F3” and “phase boundary reaction R2,” which were also in good agreement with corresponding experimental data. It was found that the addition of the HTs increased the apparent activation energy Ea of the PP/HTs comparing to the PP, which improved the thermal stability of the polypropylene. A difference in the set of kinetic and thermodynamic parameters was also observed between the PP/HTs and PP, particularly with respect to lower ΔS≠ value assigned to higher thermal stability of the PP/HTs composite.

scholarly journals Improved Hydrophobicity of Macroalgae Biopolymer Film Incorporated with Kenaf Derived CNF Using Silane Coupling Agent

Molecules ◽  
2021 ◽  
Vol 26 (8) ◽  
pp. 2254
Author(s):  
Adeleke A. Oyekanmi ◽  
N. I. Saharudin ◽  
Che Mohamad Hazwan ◽  
Abdul Khalil H. P. S. ◽  
Niyi G. Olaiya ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Coupling Agent ◽  
Silane Coupling Agent ◽  
Cellulose Nanofibrils ◽  
Hydroxyl Groups ◽  
Water Contact ◽  
Silane Coupling ◽  
Cnf Films ◽  
Kenaf Bast ◽  
Thermal Stability Of

Hydrophilic behaviour of carrageenan macroalgae biopolymer, due to hydroxyl groups, has limited its applications, especially for packaging. In this study, macroalgae were reinforced with cellulose nanofibrils (CNFs) isolated from kenaf bast fibres. The macroalgae CNF film was after that treated with silane for hydrophobicity enhancement. The wettability and functional properties of unmodified macroalgae CNF films were compared with silane-modified macroalgae CNF films. Characterisation of the unmodified and modified biopolymers films was investigated. The atomic force microscope (AFM), SEM morphology, tensile properties, water contact angle, and thermal behaviour of the biofilms showed that the incorporation of Kenaf bast CNF remarkably increased the strength, moisture resistance, and thermal stability of the macroalgae biopolymer films. Moreover, the films’ modification using a silane coupling agent further enhanced the strength and thermal stability of the films apart from improved water-resistance of the biopolymer films compared to unmodified films. The morphology and AFM showed good interfacial interaction of the components of the biopolymer films. The modified biopolymer films exhibited significantly improved hydrophobic properties compared to the unmodified films due to the enhanced dispersion resulting from the silane treatment. The improved biopolymer films can potentially be utilised as packaging materials.

scholarly journals Thermal stability and diffusion characteristics of ultrathin amorphous carbon films grown on crystalline and nitrogenated silicon substrates by filtered cathodic vacuum arc deposition

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Shengxi Wang ◽  
Anurag Roy ◽  
Kyriakos Komvopoulos
Keyword(s):  
Thermal Stability ◽  
Amorphous Carbon ◽  
Silicon Substrate ◽  
Elevated Temperatures ◽  
Carbon Films ◽  
Vacuum Arc ◽  
Cross Sectional ◽  
Prolonged Heating ◽  
Filtered Cathodic Vacuum Arc ◽  
Thermal Stability Of

AbstractAmorphous carbon (a-C) films are widely used as protective overcoats in many technology sectors, principally due to their excellent thermophysical properties and chemical inertness. The growth and thermal stability of sub-5-nm-thick a-C films synthesized by filtered cathodic vacuum arc on pure (crystalline) and nitrogenated (amorphous) silicon substrate surfaces were investigated in this study. Samples of a-C/Si and a-C/SiNx/Si stacks were thermally annealed for various durations and subsequently characterized by high-resolution transmission electron microscopy (TEM) and electron energy loss spectroscopy (EELS). The TEM images confirmed the continuity and uniformity of the a-C films and the 5-nm-thick SiNx underlayer formed by silicon nitrogenation using radio-frequency sputtering. The EELS analysis of cross-sectional samples revealed the thermal stability of the a-C films and the efficacy of the SiNx underlayer to prevent carbon migration into the silicon substrate, even after prolonged heating. The obtained results provide insight into the important attributes of an underlayer in heated multilayered media for preventing elemental intermixing with the substrate, while preserving the structural stability of the a-C film at the stack surface. An important contribution of this investigation is the establishment of an experimental framework for accurately assessing the thermal stability and elemental diffusion in layered microstructures exposed to elevated temperatures.

scholarly journals Mechanical and thermal stability of retained austenite in plastically deformed bainite-based TRIP-aided medium-Mn steels

2021 ◽  
Vol 21 (3) ◽  
Author(s):  
Aleksandra Kozłowska ◽  
Adam Grajcar ◽  
Aleksandra Janik ◽  
Krzysztof Radwański ◽  
Ulrich Krupp ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Thermal Stability ◽  
Retained Austenite ◽  
Elevated Temperatures ◽  
Mechanical Performance ◽  
Mechanical Stability ◽  
Electron Backscatter Diffraction ◽  
Cost Effective ◽  
Tensile Tests ◽  
Thermal Stability Of

AbstractAdvanced medium-Mn sheet steels show an opportunity for the development of cost-effective and light-weight automotive parts with improved safety and optimized environmental performance. These steels utilize the strain-induced martensitic transformation of metastable retained austenite to improve the strength–ductility balance. The improvement of mechanical performance is related to the tailored thermal and mechanical stabilities of retained austenite. The mechanical stability of retained austenite was estimated in static tensile tests over a wide temperature range from 20 °C to 200 °C. The thermal stability of retained austenite during heating at elevated temperatures was assessed by means of dilatometry. The phase composition and microstructure evolution were investigated by means of scanning electron microscopy, electron backscatter diffraction, X-ray diffraction and transmission electron microscopy techniques. It was shown that the retained austenite stability shows a pronounced temperature dependence and is also stimulated by the manganese addition in a 3–5% range.

Thermal Breakdown Kinetics of 1-Ethyl-3-Methylimidazolium Ethylsulfate Measured Using Quantitative Infrared Spectroscopy

2017 ◽  
Vol 71 (12) ◽  
pp. 2626-2631 ◽  
Author(s):  
Jeffrey L. Wheeler ◽  
McKinley Pugh ◽  
S. Jake Atkins ◽  
Jason M. Porter
Keyword(s):  
Thermal Stability ◽  
Room Temperature ◽  
Computational Models ◽  
Elevated Temperatures ◽  
Molar Absorptivity ◽  
Ir Absorption ◽  
Optical Cell ◽  
Multiple Samples ◽  
Kinetics Of ◽  
Thermal Stability Of

In this work, the thermal stability of the room temperature ionic liquid (RTIL) 1-ethyl-3-methylimidazolium ethylsulfate ([EMIM][EtSO4]) is investigated using infrared (IR) spectroscopy. Quantitative IR absorption spectral data are measured for heated [EMIM][EtSO4]. Spectra have been collected between 25 ℃ and 100 ℃ using a heated optical cell. Multiple samples and cell pathlengths are used to determine quantitative values for the molar absorptivity of [EMIM][EtSO4]. These results are compared to previous computational models of the ion pair. These quantitative spectra are used to measure the rate of thermal decomposition of [EMIM][EtSO4] at elevated temperatures. The spectroscopic measurements of the rate of decomposition show that thermogravimetric methods overestimate the thermal stability of [EMIM][EtSO4].

scholarly journals Thermal Stability of Residual Stresses in Differently Deep Rolled Surface Layers of Steel SAE 1045

2021 ◽  
Author(s):  
Stephanie Saalfeld ◽  
Thomas Wegener ◽  
Berthold Scholtes ◽  
Thomas Niendorf
Keyword(s):  
Thermal Stability ◽  
Elevated Temperature ◽  
Residual Stresses ◽  
Elevated Temperatures ◽  
Fatigue Behavior ◽  
Decisive Role ◽  
Deep Rolling ◽  
Material Conditions ◽  
The Stability ◽  
Thermal Stability Of

AbstractThe stability of compressive residual stresses generated by deep rolling plays a decisive role on the fatigue behavior of specimens and components, respectively. In this regard, deep rolling at elevated temperature has proven to be very effective in stabilizing residual stresses when fatigue analysis is conducted at ambient temperature. However, since residual stresses can be affected not only by plastic deformation but also when thermal energy is provided, it is necessary to analyze the influence of temperature and time on the relaxation behavior of residual stresses at elevated temperature. To evaluate the effect of deep rolling at elevated temperatures on stability limits under thermal as well as combined thermo-mechanical loads, the present work introduces and discusses the results of investigations on the thermal stability of residual stresses in differently deep rolled material conditions of the steel SAE 1045.

Study of Thermal Behaviour of EPDM/SBR Blends and Carbon Nanocoatings Deposited by Sputtering

2021 ◽  
Vol 875 ◽  
pp. 116-120
Author(s):  
Muhammad Alamgir ◽  
Faizan Ali Ghauri ◽  
Waheed Qamar Khan ◽  
Sajawal Rasheed ◽  
Muhammad Sarfraz Nawaz ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Weight Loss ◽  
Thermogravimetric Analysis ◽  
Thermal Behavior ◽  
Thermal Behaviour ◽  
X Ray Diffraction ◽  
X Ray ◽  
Thermal Stability Of

In this study, the effect of SBR concentration (10 Phr, 20 Phr & 30 Phr ) on the thermal behavior of EPDM/SBR blends was studied. Thermogravimetric analysis (TGA) was used to check weight loss of samples as function of temperature by heating upto 600°C. X-ray diffraction (XRD) was performed to determine quality and % crystallinity of the elastomer blends. It was seen that % crystallinity improved with an increase in the content of SBR in EPDM/SBR blends. TGA revealed that the thermal stability of EPDM/SBR blends has improved by 17% than neat EPDM. Carbon nano-coatings produced by sputtering have no beneficial influence on thermal behaviour of elastomers.

Enhanced Thermal Stability of Esterified Lignin in Different Solvent Mediums

2018 ◽  
Vol 9 (1) ◽  
pp. 39-49 ◽  
Author(s):  
Sharifah Nurul Ain Syed Hashim ◽  
Sarani Zakaria ◽  
Chin Hua Chia ◽  
Sharifah Nabihah Syed Jaafar
Keyword(s):  
Thermal Stability ◽  
Alkaline Solution ◽  
Room Temperature ◽  
Hydroxyl Groups ◽  
Aqueous Alkaline Solution ◽  
Alkali Lignin ◽  
Weight Percentage ◽  
H Nmr ◽  
Ft Ir ◽  
Thermal Stability Of

In this study, soda alkali lignin from oil palm empty fruit bunch (EFB-AL) and kenaf core (KC-AL) are esterified with maleic anhydride under two different conditions, namely i) pyridine at temperature of 120°C for 3h and ii) aqueous alkaline solution at room temperature for 4h. As a result, the weight percentage gain (WPG) of the esterified EFB-AL (EFB-EL) and esterified KC-AL (KC-EL) in pyridine demonstrated a higher compared to aqueous alkaline solution. The FT-IR results of EFB-EL and KC-EL in both solvents exhibited some changes at the carbonyl and hydroxyl groups. Furthermore, the esterification process induced the carboxylic peak to appear in both alkali lignin samples. The outcome is confirmed by conducting H-NMR analysis, which demonstrated ester and carboxylic acid peaks within the spectral analysis. Finally, the TGA results showed both EFB-EL and KC-EL that are exposed to aqueous alkaline actually possessed better thermal stability and higher activation energy (Ea) compared to the esterified samples in pyridine.

scholarly journals STUDY OF THERMAL DECOMPOSITION PRODUCTS OF NITROGEN-PHOSPHORUS-POTASSIUM FERTILIZERS BASED ON AMMONIUM NITRATE BY X-RAY DIFFRACTUON

2017 ◽  
Vol 61 (1) ◽  
pp. 72
Author(s):  
Konstantin G. Gorbovskiy ◽  
Alena S. Ryzhova ◽  
Andrey M. Norov ◽  
Denis A. Pagaleshkin ◽  
Valentina N. Kalinina ◽  
...  
Keyword(s):  
Thermal Stability ◽  
Thermal Decomposition ◽  
Phosphoric Acid ◽  
Ammonium Nitrate ◽  
Confined Space ◽  
Decomposition Products ◽  
X Ray ◽  
Thermal Decomposition Products ◽  
Nitrogen Phosphorus ◽  
Thermal Stability Of

Complex mineral ammonium nitrate-based fertilizers are complex multicomponent salt systems possessing low thermal stability and prone to self-sustaining decomposition. This leads to the need to increase the requirements for fire and explosion safety in their manufacture, storage and transportation, caused by the fact that ammonium nitrate is a solid oxidant able to support a combustion, and its heating in confined space can lead to detonation. Components that make up such fertilizers can both reduce (phosphates and ammonium sulfate) and accelerate (chlorine compounds) decomposition of ammonium nitrate. Thus, the thermal stability of fertilizers based on ammonium nitrate largely depends on the ratio of the components that make up its composition or formed as a result of the chemical reaction. The simplest way to reduce the content of ammonium nitrate and increase the thermal stability of fertilizer without changing the content of essential nutrients is to increase the degree of phosphoric acid ammoniation. In this paper, the phase composition change of grade 22:11:11 nitrogen-phosphorus-potassium fertilizer obtained with different ammoniation degree in the process of thermal decomposition was studied by X-ray phase analysis. To obtain this fertilizer, wet-process phosphoric acid obtained sulfuric acid attack of the Khibin apatite concentrate by a hemihydrate method is used. It is shown that an increase in the ammoniation degree has a significant effect on the exothermic decomposition of ammonium nitrate and the amount of material that is released into the gas phase. The phases formed at each stage of the decomposition are determined.Forcitation:Gorbovskiy K.G., Ryzhova A.S., Norov A.M., Pagaleshkin D.A., Kalinina V.N., Mikhaylichenko A.I. Study of thermal decomposition products of nitrogen-phosphorus-potassium fertilizers based on ammonium nitrate by X-ray diffractuon. Izv. Vyssh. Uchebn. Zaved. Khim. Khim. Tekhnol. 2018. V. 61. N 1. P. 72-77

Sign in / Sign up

Export Citation Format

Share Document