Anisotropy Gas Reservoir Drainage Radius and Quantitative Well Interference Study

2013 ◽  
Vol 275-277 ◽  
pp. 1285-1291 ◽  
Author(s):  
Zheng Long Gao ◽  
Hong Fu Fan ◽  
Zhi Bin Gao
Keyword(s):  
Production Rate ◽  
Major Axis ◽  
Productivity Analysis ◽  
Analysis Method ◽  
Equivalent Radius ◽  
Average Value ◽  
Drainage Radius ◽  
Well Spacing ◽  
Cumulative Production ◽  
The Difference

Unstable productivity analysis method was used to obtain the equivalent radius of 77 wells and the result shows that the equivalent radius ranges from 30 to 970m with an average value of 230m in McKittrick Hills. The difference range of the radius is mainly caused by varying formation properties, gas saturation, production time, etc. Permeability anisotropy changes the drainage from round to ellipse. The major axis and the minor axis of the ellipse are determined by the ratio of major and minor permeability. Current pressure distribution was obtained and was found to be consistent with the modified drainage results, which demonstrates that the unstable productivity analysis method is applicable in the study of gas well drainage radius. An interference well and an observation well’s model was constructed to study well interference quantitatively. When the well spacing is larger than 750m, the productivity will be reduced by 20%. The production rate of interference well is more sensitive to the cumulative production of observation well, when the production rate of interference well is below 16.8×104m3/d.

Implementasi Sistem Informasi Monitoring Pengolahan Data Inventory Gudang Pada PT.Talaga Mulya Indah

2020 ◽  
Vol 6 (2) ◽  
pp. 187-197
Author(s):  
Nurlaila Suci Rahayu Rais ◽  
Dedeh Apriyani ◽  
Gito Gardjito
Keyword(s):  
Data Processing ◽  
Integrated Control ◽  
Unified Modeling Language ◽  
Review Literature ◽  
Analysis Method ◽  
Inventory Data ◽  
Literature Study ◽  
Unified Modeling ◽  
The Difference ◽  
The Right

Monitoring of warehouse inventory data processing is an important thing for companies. PT Talaga mulya indah is still manual using paper media, causing problems that have an effect on existing information, namely: problems with data processing of incoming and outgoing goods. And the difference between data on the amount of stock of goods available with physical data, often occurs inputting data more than once for the same item, searching for available data, and making reports so that it impedes companies in monitoring inventory of existing stock of goods. Which aims to create a system that can provide updated information to facilitate the warehouse admin in making inventory reports, and reduce errors in input by means of integrated control. In this study, the authors used the data collection method used in this analysis using the method of observation, interviews, and literature review (literature study). For analysis using the PIECES analysis method. Furthermore, the system design used is UML (Unified Modeling Language). The results of this study are expected to produce the right data in the process of monitoring inventory data processing, also can provide the right information and make it easier to control the overall availability of goods.

The Effect of Jigsaw Methode and Motivation on Students’ of Learning Outcomes

2020 ◽  
Vol 3 (1) ◽  
pp. 20-30
Author(s):  
Yunita Yunita ◽  
Hidayat Hidayat ◽  
Harun Sitompul
Keyword(s):  
Cooperative Learning ◽  
Student Learning ◽  
Learning Outcomes ◽  
Student Learning Outcomes ◽  
Learning Motivation ◽  
Learning Approaches ◽  
High Learning ◽  
Average Value ◽  
The Difference ◽  
Low Motivation

This study aims to: (1) investigate the effect of Jigsaw cooperative learning on students learning outcomes; (2) find the difference in learning outcomes between high and low learning motivation and (3) find the interaction between learning approaches and learning motivation towards learning outcomes. The population of the study is students of grade IVa, IVb, IVc at SD Kasih Ibu Patumbak and the sample in this study is grade IVa with 35 students and grade IVb with 35 students. The results show that: (1) the average student learning outcomes of jigsaw cooperative learning is 28.40 while conventional is 24.14. Thus, students learning outcomes that get cooperative learning of jigsaw type are higher than conventional learning, (2) Students who have high motivation get an average value = 30.74, while low motivation is 22.72. Thus, it can be concluded that there are differences in student learning outcomes having high learning motivation and low learning motivation, and (3) students learning outcomes  taught by jigsaw cooperative learning are high learning motivation groups (32.94), and low learning motivation groups (24.58), while students taught with conventional learning are high learning motivation groups (28.40 ), and low motivation groups (20,95). Thus, there is no interaction between learning approaches and learning motivation towards learning outcomes.

Pandhawa Gubah sebagai Representasi Interaksi Metafisik Manusia Jawa dan Perbandingannya dengan Cheritera Pandawa Lima

Manuskripta ◽  
2020 ◽  
Vol 10 (1) ◽  
pp. 67
Author(s):  
Novarina Novarina
Keyword(s):  
Comparative Study ◽  
Literary Theory ◽  
Research Method ◽  
Descriptive Analysis ◽  
Literary Study ◽  
Analysis Method ◽  
Research Objects ◽  
Similarities And Differences ◽  
The Difference ◽  
The Comparative Study

Abstract: This research is a comparative literary study that uses Malay and Javanese versions of Mahabarata text sources. The research objects used were the text edition of Pandhawa Gubah (PG) by Sudibjo Z. Hadisutjipto and the text of Cheritera Pandawa Lima (CPL) by Khalid Hussain. The research method used is descriptive-analysis method. In the comparative study used a comparative literary theory proposed by Endraswara (2011). The results of the text comparison reveal the similarities and differences in the image of Bima figures in the Javanese and Malay versions. The equation as a whole is that both texts contain the same heroic storyline and heroic character, Bima. In addition, Indian influence is still evident in the two texts seen from the nuances of Hinduism that exist in both texts. While the difference is seen in the events that accompany Bima's struggle in achieving his victory. Based on these similarities and differences, it can be seen that the authors attempt to represent the concept of metaphysical interactions vertically and horizontally expressed through PG text. --- Abstrak: Penelitian ini adalah satu kajian sastra bandingan yang menggunakan sumber teks Mahabarata versi Melayu dan Jawa. Objek penelitian yang digunakan adalah edisi teks Pandhawa Gubah (PG) karya Sudibjo Z. Hadisutjipto dan teks Cheritera Pandawa Lima (CPL) karya Khalid Hussain. Metode penelitian yang digunakan adalah metode deskriptif-analisis. Dalam telaah perbandingan digunakan teori sastra bandingan yang dikemukakan Endraswara (2011). Hasil perbandingan teks mengungkapkan adanya persamaan dan perbedaan citra tokoh Bima dalam versi Jawa maupun versi Melayu. Persamaan secara keseluruhan adalah kedua teks tersebut mengandung alur cerita kepahlawanan dan tokoh pahlawan yang sama yaitu Bima. Selain itu, pengaruh India masih tampak dalam kedua teks tersebut dilihat dari nuansa Hinduisme yang ada dalam kedua teks. Sementara perbedaannya tampak pada peristiwa-peristiwa yang menyertai perjuangan Bima dalam mencapai kemenangannya. Berdasarkan persamaan dan perbedaan tersebut tampak adanya upaya penulis untuk merepresentasikan konsep interaksi metafisik secara vertikal dan horizontal yang diungkapkan melalui teks PG.

Kesalahan Penggunaan Bahasa Perancis dalam Tulisan Mahasiswa Program Studi Sastra Perancis Unpad

Metahumaniora ◽  
2017 ◽  
Vol 7 (3) ◽  
pp. 368
Author(s):  
Gilang Januarsyah
Keyword(s):  
General Public ◽  
Qualitative Approach ◽  
French Language ◽  
Analysis Method ◽  
Writing Skill ◽  
Language Writing ◽  
The Difference ◽  
Observation Method ◽  
Bahasa Indonesia

ABSTRAKUntuk menghasilkan sebuah karangan berbahasa Perancis yang dapat dipahamioleh khalayak umum, mahasiswa harus menguasai kemampuan berbahasa Perancis ragamtulis yang baik dan benar sesuai dengan kaidah yang berlaku. Penelitian ini bertujuanuntuk menjelaskan kesalahan sintaksis yang dilakukan oleh mahasiswa Program StudiSastra Perancis Universitas Padjadjaran. Data yang digunakan dalam penelitian ini diambildari sepuluh karangan mahasiwa yang duduk di semester lima dan tujuh dan dianalisisdengan menggunakan metode simak dan metode analisis padan referensial translasionaldengan pendekatan kualitatif. Hasil dari penelitian ini menunjukkan bahwa kesalahantertinggi yang dilakukan mahasiswa adalah kesalahan dalam penggunaan passé composédan imparfait sebesar 50%, kemudian diikuti oleh kesalahan dalam penggunaan pronomrelatif simple et composé ‘pronomina penghubung bebas dan turunan’ sebesar 30%, danterakhir kesalahan dalam penggunaan pronom COD et COI ‘pronomina COD dan COI’ sebesar20%. Faktor yang menyebabkan terjadinya kesalahan tersebut adalah faktor linguistikyang disebabkan oleh perbedaan kaidah tatabahasa bahasa Indonesia dan Perancis.Selain itu terdapat pula faktor sosiolinguistik yang disebabkan oleh jarangnya mahasiswamembiasakan diri mereka untuk mengaplikasikan bahasa Perancis di luar kelas.Kata kunci: kesalahan, sintaksis, bahasa Perancis, tulis, pengajaranABST RACTTo produce a French-language essay that can be understood by the general public,the students should master the ability of French language in good and true writing skill inaccordance with the applicable rules. The aim of this research is to explain the syntactic errorsmade by students of French literature’s program at University Padjadjaran. The sources ofdata are taken from the ten student essays who sit in the fifth and seventh semesters, and themethods used in this research are Observation Method ‘Metode Simak’ and the analyticalreference translational analysis method with a qualitative approach. The results of thisresearch indicate that the highest errors that students make are the use of passé composéand imparfait as much as fifty percent, followed by errors in the use of pronom relatifsimple et composé ‘the free and derivative pronouns’ thirty percent, and the last error is inthe use of pronom CO D et CO I ‘‘The COD and COI pronouns’ twenty percent. The factors thatcause those errors are a linguistic caused by the difference rules of Indonesian and Frenchgrammar. In addition there are also sociolinguistic factors caused by the rarity of studentsfamiliarize themselves to apply the French language outside the classroom.Keywords: Error, syntax, French language, writing, teaching

Pengaruh Jumlah Pencucian Beras dengan Kadar Klorin

2017 ◽  
Vol 1 (1) ◽  
pp. 89
Author(s):  
Indah Purwaningsih ◽  
Supriyanto Supriyanto
Keyword(s):  
Mucous Membrane ◽  
Confidence Level ◽  
Iodometric Titration ◽  
Titration Method ◽  
Anova Test ◽  
Average Value ◽  
Significant Difference ◽  
The Difference

Abstract: Chlorine is a green halogen-shaped halogen gas at normal temperature and serves as bleach, stain remover and disinfectant. Chlorine is now widely used for bleaching rice so that less quality rice looks like quality rice. Chlorine is very toxic and causes mucous membrane irritation, highly reactive and very powerful oxidizer. The purpose of this research was to determine the difference of chlorine level in chlorinated rice washed once, twice and 3 times. The sample in this study amounted to 11 samples calculated by replication formula. Each sample was treated 3 times, ie 1 washed once, 2 washed twice and washed 3 times. The samples then examined by iodometric titration method. Based on the results of the study using ANOVA test, 11 samples obtained the average value of chlorine after washed once amount of 0.0176%, after washed twice amount of 0.0111%, and after washed 3 times amount of 0.0052% with the value significance p = 0.03 (p <0.05) at 95% confidence level which means there was a significant difference between chlorine levels in chlorinated rice washed once, twice and 3 times.Abstrak: Klorin merupakan unsur halogen berbentuk gas berwarna kuning kehijauan pada suhu normal danberfungsi sebagai pemutih, penghilang noda maupun desinfektan. Klorin sekarang banyak digunakan untuk bahan pemutih beras agar beras yang kurang berkualitas tampak seperti beras berkualitas. Klorin sangat toksik dan menyebabkan iritasi membran mukosa, sangat reaktif dan merupakan oksidator yang sangat kuat. Tujuan dari penelitian ini ialah untuk mengetahui perbedaan kadar klorin pada beras berklorin yang dicuci sebanyak 1 kali, 2 kali dan 3 kali. Sampel dalam penelitian ini berjumlah 11 sampel yang dihitung dengan rumus replikasi. Setiap sampel diberi perlakuan sebanyak 3 kali, yaitu 1 kali pencucian, 2 kali pencucian dan 3 kali pencucian. Sampel penelitian kemudian diperiksa dengan metode titrasi iodometri. Berdasarkan hasil penelitian menggunakan uji Anova secara komputerisasi terhadap 11 sampel diperoleh nilai rata-rata kadar klorin setelah 1 kali pencucian sebesar 0,0176 %, setelah 2 kali pencucian sebesar 0,0111 %, dan setelah 3 kali pencucian sebesar 0,0052 % dengan nilai signifkansi p = 0,03 (p<0,05) pada tingkat kepercayaan 95% yang artinya ada perbedaan yang bermakna antara kadar klorin pada beras berklorin yang dicuci sebanyak 1 kali, 2 kali dan 3 kali.

Results of studying the dimensional accuracy of the bases of complete removable prostheses made using 3D printing and traditional technologies

2020 ◽  
pp. 34-39
Author(s):  
Vokulova Yu.A. Vokulova ◽  
E.N. Zhulev
Keyword(s):  
3D Printing ◽  
Traditional Method ◽  
Laser Scanning ◽  
Laser Scanner ◽  
Digital Technologies ◽  
Dimensional Accuracy ◽  
3D Printer ◽  
Significance Level ◽  
Average Value ◽  
The Difference

This article presents the results of studying the dimensional accuracy of the bases of complete removable prostheses made using a 3D printer and the traditional method. Bases of complete removable prostheses were made using an intraoral laser scanner iTero Cadent (USA) and a 3D printer Asiga Max UV (Australia). To study the dimensional accuracy of the bases of complete removable prostheses, we used the DentalCAD 2.2 Valletta software. The Nonparametric Wilcoxon W-test was used for statistical analysis of the obtained data. We found that the average value of the difference with the standard for bases made using digital technologies is 0.08744±0.0484 mm. The average value of the difference with the standard for bases made by the traditional method is 0.5654±0.1611 mm. Based on these data, we concluded that the bases of complete removable prostheses made using modern digital technologies (intraoral laser scanning and 3D printer) have a higher dimensional accuracy compared to the bases of complete removable prostheses made using the traditional method with a significance level of p<0.05 (Wilcoxon's W-test=0, p=0.031). Keywords: digital technologies in dentistry, digital impressions, intraoral scanner, 3D printing, ExoCAD, complete removable dentures.

Unified Assessment of Unconventional Resource Plays – Implications for Global Exploration and Development

2021 ◽  
Author(s):  
Tarun Grover ◽  
Jamie Stuart Andrews ◽  
Irfan Ahmed ◽  
Ibnu Hafidz Arief
Keyword(s):  
Commodity Prices ◽  
Design Parameters ◽  
First Year ◽  
Well Productivity ◽  
Well Spacing ◽  
Cumulative Production ◽  
Unconventional Resource ◽  
Log Normal ◽  
The Impact ◽  
Sweet Spots

Abstract Unconventional resource plays, herein referred to as source rock plays, have been able to significantly increase the supply of hydrocarbons to the world. However, majority of the companies developing these resource plays have struggled to generate consistent positive cash flows, even during periods of stable commodity prices and after successfully reducing the development costs. The fundamental reasons for poor financial performance can be attributed to various reasons, such as; rush to lease acreage and drill wells to hold acreage, delayed mapping of sweet spots, slow acknowledgement of high geological variability, spending significant capital in trial and errors to narrow down optimal combinations of well spacing and stimulation designs. The objective of this paper is to present a systematic integrated multidisciplinary analysis of several unconventional plays worldwide which, if used consistently, can lead to significantly improved economics. We present an analysis of several unconventional plays in the US and Argentina with fluid systems ranging from dry gas to black oil. We utilize the publicly available datasets of well stimulation and production data along with laboratory measured core data to evaluate the sweet spots, the measure of well productivity, and the variability in well productivity. We investigate the design parameters which show the strongest correlation to well productivity. This step allows us to normalize the well productivity in such a way that the underlying well productivity variability due to geology is extracted. We can thus identify the number of wells which should be drilled to establish geology driven productivity variability. Finally, we investigate the impact of well spacing on well productivity. The data indicates that, for any well, first year cumulative production is a robust measure of ultimate well productivity. The injected slurry volume shows the best correlation to the well productivity and "completion normalized" well productivity can be defined as first year cumulative production per barrel of injected slurry volume. However, if well spacing is smaller than the created hydraulic fracture network, the potential gain of well productivity is negated leading to poor economics. Normalized well productivity is log-normally distributed in any play due to log-normal distribution of permeability and the sweet spots will generally be defined by most permeable portions of the play. Normalized well productivity is shown to be independent of areal scale of any play. We show that in every play analyzed, typically 20-50 wells (with successful stimulation and production) are sufficient to extract the log-normal productivity distribution depending on play size and target intervals. We demonstrate that once the log-normal behavior is anticipated, creation of production profiles with p10-p50-p90 values is quite straightforward. The way the data analysis is presented can be easily replicated and utilized by any operator worldwide which can be useful in evaluation of unconventional resource play opportunities.

Electronic irradiation of TlInSxSe2−x (x = 1): Morphology, structure and raman scattering

2021 ◽  
Author(s):  
M. Yu. Tashmetov ◽  
F. K. Khallokov ◽  
N. B. Ismatov ◽  
I. I. Yuldashova ◽  
S. Kh. Umarov
Keyword(s):  
Surface Morphology ◽  
Single Crystal ◽  
Single Phase ◽  
Phase State ◽  
Monoclinic Structure ◽  
Average Value ◽  
Single Phase State ◽  
Before And After ◽  
Electronic Irradiation ◽  
The Difference

It is shown that the replacement of a part of sulfur atoms with selenium atoms in a TlInS2 single crystal stimulates the formation of a single-phase state with a monoclinic structure (space group [Formula: see text]/[Formula: see text] in TlInS[Formula: see text]Se[Formula: see text] ([Formula: see text]). Irradiation with 2 MeV electrons and a fluence of [Formula: see text] electron/cm2 of powder TlInS[Formula: see text]Se[Formula: see text] ([Formula: see text]) leads to an increase in the crystallite size from 56.5 nm to 65 nm, which is most likely associated with a decrease in the interface. The difference between the surface morphology of the synthesized TlInS[Formula: see text]Se[Formula: see text] ([Formula: see text]) single crystal and the surface morphology of the TlInS2 single crystal is established, which consists in a decrease in the height and width of the roughness in TlInS[Formula: see text]Se[Formula: see text] ([Formula: see text]). Irradiation of a TlInS[Formula: see text]Se[Formula: see text] ([Formula: see text]) single crystal with electrons with a fluence of [Formula: see text] electron/cm2 does not lead to a change in the height of the tubercle on its surface, and the average value of its width increases more than ten-fold. The identity of the peaks in the Raman spectra of the TlInS[Formula: see text]Se[Formula: see text] ([Formula: see text]) single crystal before and after its irradiation with electrons with an energy of 2 MeV and upto a fluence of [Formula: see text] electron/cm2, along with the absence of a shift of the peaks, indicates the radiation resistance of the TlInS[Formula: see text]Se[Formula: see text] ([Formula: see text]) single crystal.

Analyzing the Impacts of Meshing and Grid Alignment in Dual-Porosity Dual-Permeability Upscaling

2021 ◽  
pp. 1-20
Author(s):  
Ziming Xu ◽  
Juliana Y. Leung
Keyword(s):  
Fracture Network ◽  
Fracture Plane ◽  
Fracture Density ◽  
Shape Factors ◽  
Stimulated Reservoir Volume ◽  
Reservoir Volume ◽  
Multiple Length Scales ◽  
Fracture Intensity ◽  
Cumulative Production ◽  
The Difference

Summary The discrete fracture network (DFN) model is widely used to simulate and represent the complex fractures occurring over multiple length scales. However, computational constraints often necessitate that these DFN models be upscaled into a dual-porositydual-permeability (DPDK) model and discretized over a corner-point grid system, which is still commonly implemented in many commercial simulation packages. Many analytical upscaling techniques are applicable, provided that the fracture density is high, but this condition generally does not hold in most unconventional reservoir settings. A particular undesirable outcome is that connectivity between neighboring fracture cells could be erroneously removed if the fracture plane connecting the two cells is not aligned along the meshing direction. In this work, we propose a novel scheme to detect such misalignments and to adjust the DPDK fracture parameters locally, such that the proper fracture connectivity can be restored. A search subroutine is implemented to identify any diagonally adjacent cells of which the connectivity has been erroneously removed during the upscaling step. A correction scheme is implemented to facilitate a local adjustment to the shape factors in the vicinity of these two cells while ensuring the local fracture intensity remains unaffected. The results are assessed in terms of the stimulated reservoir volume calculations, and the sensitivity to fracture intensity is analyzed. The method is tested on a set of tight oil models constructed based on the Bakken Formation. Simulation results of the corrected, upscaled models are closer to those of DFN simulations. There is a noticeable improvement in the production after restoring the connectivity between those previously disconnected cells. The difference is most significant in cases with medium DFN density, where more fracture cells become disconnected after upscaling (this is also when most analytical upscaling techniques are no longer valid); in some 2D cases, up to a 22% difference in cumulative production is recorded. Ignoring the impacts of mesh discretization could result in an unintended reduction in the simulated fracture connectivity and a considerable underestimation of the cumulative production.

Stem eccentricity in coastal western hemlock

1981 ◽  
Vol 11 (3) ◽  
pp. 715-718 ◽  
Author(s):  
Robert M. Kellogg ◽  
Francis J. Barber
Keyword(s):  
Major Axis ◽  
Western Hemlock ◽  
Eccentricity Ratio ◽  
Angular Rotation ◽  
Minimum Diameter ◽  
Breast Height ◽  
Second Growth ◽  
The Difference ◽  
Average Eccentricity ◽  
Practical Field

Stem eccentricity in second-growth western hemlock (Tsugaheterophylla (Raf.) Sarg.) from southern coastal British Columbia appears to be the rule rather than the exception. Although the difference was small, the average eccentricity ratios (ratios of minimum diameter inside bark (DIB) to maximum DIB) for two Lower Mainland sites were significantly larger than those of two Vancouver Island sites. The average eccentricity ratio of all 87 trees studied was 0.929, with a standard deviation of 0.0231. The angular rotation of the major axis of the stem cross section varied greatly, and was positively related to the average stem eccentricity ratio within 5-m log lengths for each stem. Average eccentricity of the whole stem was relatively independent of diameter at breast height (DBH), age, stem height, and eccentricity at breast height. It does not appear that a practical field technique could be devised for the rapid estimation of average stem eccentricity in western hemlock.

Sign in / Sign up

Export Citation Format

Share Document