Biological Purification of Silicate Minerals

2007 ◽  
Vol 20-21 ◽  
pp. 126-129 ◽  
Author(s):  
Iveta Štyriaková ◽  
Michal Lovás
Keyword(s):  
Magnetic Separation ◽  
Heterotrophic Bacteria ◽  
Raw Materials ◽  
Iron Removal ◽  
Low Grade ◽  
Silicate Mineral ◽  
Iron Extraction ◽  
Fine Grained ◽  
Fe Content ◽  
Quartz Sands

Bioleaching is technology applicable to iron extraction from low-grade non-metallic raw materials. Bioleaching of quartz sands and feldspars involves the action of heterotrophic bacteria. Impurities include fine – grained limonite, goethite, hematite or mica were removed by the reductive dissolution of Fe3+ in linked with the silicate mineral destruction. Heterotrophic bacteria produced organic acids that are able to solubilize Fe oxide and silicates but require organic carbon as a source of energy. Molasses is a relatively inexpensive carbon source used for various industrial fermentations and contains also other nutrients that accounted for the enhancement of iron dissolution in this study. The admixture of pigments in molasses coloured the samples, but the discoloration could be removed by the addition of NaClO following the bioleaching step. The feasibility of the bioleaching treatment has to be tested specifically to each type of silicate raw materials. The Fe content in the quartz sands and feldspar samples by the biological leaching decreased as much as 60% and by subsequent using of electromagnetic separation of feldspars, the decrease of Fe content in 74% was achieved. However, the application of magnetic separation of quartz sands after bioleaching resulted in total iron removal of 93 % and in such combined way prepared product contained 0.024 % of Fe2O3. Achieved results on iron removal point to the fact that combination of leaching and magnetic separation enables to obtain product usable in glass and ceramic industry.

scholarly journals Factors affecting bioleaching in the processing of non-metallics

2022 ◽  
Vol 7 (1) ◽  
pp. 11-16
Author(s):  
Iveta Štyriaková
Keyword(s):  
Magnetic Separation ◽  
Iron Removal ◽  
Raw Material ◽  
Bacterial Leaching ◽  
Iron Dissolution ◽  
Electromagnetic Separation ◽  
Factors Affecting ◽  
Fe Content ◽  
Quartz Sands ◽  
Physicochemical Factors

Biotechnological treatment of non-metallics is based on bacterial leaching of raw material and dissolution of Fe. Bacterial iron dissolution ability is dependent on various physicochemical factors as temperature, acidity of solutions, redox potential, rapidity of water circulation and presence of organic sources. The Fe content in the quartz sands and feldspar samples by the biological leaching decreased as much as 60% and by subsequent using of electromagnetic separation of feldspars, the decrease of Fe content in 74% was achieved. However, the application of magnetic separation of quartz sands after bioleaching resulted in total iron removal of 93% and in such combined way prepared product contained 0.024 % of Fe2O3. Achieved results on iron removal point to the fact that combination of leaching and magnetic separation enables to obtain product usable in glass and ceramic industry.

scholarly journals INFLUENCE OF ZnO AND BaSO4 ADDITIVES ON CONSTRUCTION AND TECHNICAL PROPERTIES OF THE WEAK BASE WHITE CEMENTS

2020 ◽  
pp. 17-24
Author(s):  
T.I. Timoshenko ◽  
A. Zalogina ◽  
V. Hudasov
Keyword(s):  
Production Technology ◽  
Raw Materials ◽  
Construction Material ◽  
Weak Base ◽  
Fine Grained ◽  
Specialized Production ◽  
White Cement ◽  
Quartz Sands ◽  
Technical Properties ◽  
Clay Component

white cement – modern construction material which is increasingly popular every year as it is used not only in the construction sphere, but also and in creation of architectural products. Today the most famous producers of white cement is Turkey, Denmark and Egypt. Special color of cement is reached due to specific structure and the specialized production technology. Clinker for the white portlandtsement, differs from usual in the increased maintenance of Si2O (23.5-25.5%) and A12O3 (5.5-7%), insignificant quantity of Fe2O3 (up to 0.25-0.35%) and MnO – 0.05-0.15%. The mineral composition of clinker for white cements fluctuates within (%): C3S – 35-50; 35-45; C3A 14-17; C4AF 0.9-1.4. The maintenance of MgO in it should not exceed 4.5%. For production of the white portlandtsement the cleanest kinds of carbonate and sandy-argillaceous raw materials are used. In particular, the straight limestones or chalk containing no more than 0.15% of the painting oxides are applied. The kaolin, waste of its enrichment and other materials are served as a clay component. The fine-grained white quartz sands, waste of quartz sand received at enrichment of a kaolin, etc. to increase in the silicate module are applied. The ashless fuel which is not forming soot and ashes that helps to avoid pollution is applied to roasting of clinker. Crushing of raw materials is carried out in special mills, and crushing is carried out by means of silicon or porcelain elements. Such production technology helps to achieve the grinding having higher rates than from traditional cements. Results of a research of influence of mineral BaSO4 and ZnO additives on synthesis and properties of the low-main clinker of the white portlandtsement are given in work: clinker formation, hydration activity, whiteness of cement.

TEM/AEM characterization of fine-grained clay minerals in very-low-grade rocks: Evaluation of contamination by empa involving celadonite family minerals

1996 ◽  
Vol 54 ◽  
pp. 694-695
Author(s):  
Gejing Li ◽  
D. R. Peacor ◽  
D. S. Coombs ◽  
Y. Kawachi
Keyword(s):  
Electron Microscopy ◽  
Volcanic Rocks ◽  
Analytical Electron Microscopy ◽  
Metamorphic Rocks ◽  
New Mineral ◽  
Chemical Compositions ◽  
Low Grade ◽  
Fine Grained ◽  
Depth Analysis ◽  
Mineral Aggregates

Recent advances in transmission electron microscopy (TEM) and analytical electron microscopy (AEM) have led to many new insights into the structural and chemical characteristics of very finegrained, optically homogeneous mineral aggregates in sedimentary and very low-grade metamorphic rocks. Chemical compositions obtained by electron microprobe analysis (EMPA) on such materials have been shown by TEM/AEM to result from beam overlap on contaminant phases on a scale below resolution of EMPA, which in turn can lead to errors in interpretation and determination of formation conditions. Here we present an in-depth analysis of the relation between AEM and EMPA data, which leads also to the definition of new mineral phases, and demonstrate the resolution power of AEM relative to EMPA in investigations of very fine-grained mineral aggregates in sedimentary and very low-grade metamorphic rocks.Celadonite, having end-member composition KMgFe3+Si4O10(OH)2, and with minor substitution of Fe2+ for Mg and Al for Fe3+ on octahedral sites, is a fine-grained mica widespread in volcanic rocks and volcaniclastic sediments which have undergone low-temperature alteration in the oceanic crust and in burial metamorphic sequences.

Experimental Research on the Qualitative Characteristics of Iron Ores and Ferrous Waste That Can Be Used in Blast Furnace Mixt Injection Technology

2019 ◽  
Vol 70 (11) ◽  
pp. 3835-3842
Author(s):  
Mihai Dumitru Tudor ◽  
Mircea Hritac ◽  
Nicolae Constantin ◽  
Mihai Butu ◽  
Valeriu Rucai ◽  
...  
Keyword(s):  
Blast Furnace ◽  
Experimental Research ◽  
Raw Materials ◽  
Coal Dust ◽  
Production Costs ◽  
Iron Ores ◽  
Fine Grained ◽  
Experimental Laboratory ◽  
Injection Technology ◽  
Direct Use

Direct use of iron ores in blast furnaces, without prior sintering leads to a reduction in production costs and energy consumption [1,2]. Fine-grained iron ores and iron oxides from ferrous wastes can be used together with coal dust and limestone in mixed injection technology through the furnace tuyeres. In this paper are presented the results of experimental laboratory investigations for establishing the physic-chemical characteristics of fine materials (iron ore, limestone, pulverized coal) susceptible to be used for mixed injection in blast furnace. [1,4]. The results of the experimental research have shown that all the raw materials analyzed can be used for mixt injection in blast furnace.

Thorium in crandallite-group minerals: an example from a Devonian bauxite deposit, Timan, Russia

2004 ◽  
Vol 68 (3) ◽  
pp. 489-497 ◽  
Author(s):  
L. E. Mordberg
Keyword(s):  
Crystal Lattice ◽  
Radiation Damage ◽  
Mineral Composition ◽  
Bauxite Deposit ◽  
Weathering Profile ◽  
Silicate Mineral ◽  
Fe Content ◽  
Very High ◽  
Type Substitution ◽  
Simplified Formula

AbstractA Th-rich mineral of the crandallite group has been investigated from the weathering profile of the Schugorsk bauxite deposit, Timan, Russia. It occurs within thin (up to 0.5 mm) organic-rich veinlets together with ‘leucoxene’ in the form of small shapeless grains which vary in size from 1—2 mm to 60—70 mm. Rare grains disseminated among boehmite crystals were also found. Microprobe analyses determined that the ThO2 content can be as high as 18 wt.%. The mineral composition is intermediate between crandallite CaAl3H(PO4)2(OH)6, goyazite SrAl3H(PO4)2(OH)6, Th-crandallite and svanbergite SrAl3PO4SO4(OH)6 in the beudantite group.Comparatively high contents of Fe and Si and a very high positive Th and Fe content correlation (r = +0.98) suggest that the formula of the hypothetical Th-bearing end-member is ThFe3(PO4,SiO4)2(OH)6 with Th and Si substituting for REE and Prespectively (woodhouseite-type substitution). Another possible substitution is Th4+ + Ca2+ ⇋ 2REE3+ (florencite-type). A deficiency of cations in the X site can be explained by either the presence of carbon, undetectable by microprobe, in the crystal lattice or a lack of X-site cations due to radiation damage induced by Th. Some excess of cations in the B site (Al and Fe3+) can be explained by the presence of very small boehmite and hematite inclusions on the crandallite grain surfaces. Th-rich crandallite may be the result of alteration of an unidentified silicate mineral from the parent rock with a composition close to the simplified formula Fe2+ThSiO4(OH)2.

Research on Properties of Low Grade Cement-Based Composite Materials Modified by Silica Fume

2012 ◽  
Vol 174-177 ◽  
pp. 751-756
Author(s):  
Zi Fang Xu ◽  
Ming Xu Zhang ◽  
Jin Hua Li
Keyword(s):  
Silica Fume ◽  
Mechanical Performance ◽  
Raw Materials ◽  
Cement Matrix ◽  
Hardened Cement ◽  
Low Grade ◽  
X Ray ◽  
Matrix Microstructure ◽  
Nano Powder ◽  
Strength And Durability

In order to notably improve the mechanical properties and durability of low-grade cement-based material, superfine silica fume was used to modify the cement-based composite based on special perfomance and effects of nano powder. The mechanical performance and durability were investigated.Then the phase compositions,microstructure and morphologies of as-received cement-based composite were studied by X-ray Diffractometer、TGA-DTA and SEM. The results show that： the best formula of raw materials is 1:1:0.025:0.015, and hydration can be accelerated and increasing of hydration products is observed after modification. In the hardened cement matrix, microstructure is very compacted and C-S-H gel forms densed structure, so the structure defect is notably reduced. This means that both strength and durability of cement-based composite are notably improved by the addition of superfine silica fume.

scholarly journals Impact of Sodium Hexametaphosphate on the Flotation of Ultrafine Magnesite from Dolomite-Rich Desliming Tailings

Minerals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 499
Author(s):  
Duong Huu Hoang ◽  
Doreen Ebert ◽  
Robert Möckel ◽  
Martin Rudolph
Keyword(s):  
Ultrafine Particles ◽  
Raw Materials ◽  
Low Cost ◽  
Froth Flotation ◽  
Open Circuit ◽  
Ore Deposits ◽  
Sodium Hexametaphosphate ◽  
Low Grade ◽  
Low Contrast ◽  
The Impact

The depletion of ore deposits, the increasing demand for raw materials, the need to process low-grade, complex and finely disseminated ores, and the reprocessing of tailings are challenges especially for froth flotation separation technologies. Even though they are capable of handling relatively fine grain sizes, the flotation separation of very fine and ultrafine particles faces many problems still. Further, the flotation of low-contrast semi-soluble salt-type minerals with very similar surface properties, many complex interactions between minerals, reagents and dissolved species often result in poor selectivity. This study investigates the flotation beneficiation of ultrafine magnesite rich in dolomite from desliming, currently reported to the tailings. The paper especially focuses on the impact of the depressant sodium hexametaphosphate (SHMP) on the following: (i) the froth properties using dynamic froth analysis (DFA), (ii) the separation between magnesite and dolomite/calcite, and (iii) its effect on the entrainment. As a depressant/dispersant, SHMP has a beneficial impact on the flotation separation between magnesite and dolomite. However, there is a trade-off between grade and recovery, and as well as the dewatering process which needs to be considered. When the SHMP increases from 200 g/t to 700 g/t, the magnesite grade increases from 67% to 77%, while recovery decreases massively, from 80% to 40%. The open circuit with four cleaning stages obtained a concentrate assaying 77.5% magnesite at a recovery of 45.5%. The dolomite content in the concentrate is about 20%, where 80% of dolomite was removed and importantly 98% of the quartz was removed, with only 0.3% of the quartz in the final concentrate. Furthermore, the application of 1-hydroxyethylene-1,1-diphosphonic acid (HEDP) as a more environmentally friendly and low-cost alternative to SHMP is presented and discussed. Using only 350 g/t of HEDP can achieve a similar grade (76.3%), like 700 g/t of SHMP (76.9%), while obtaining a 17% higher magnesite recovery as compared to 700 g/t of SHMP. Interestingly, the proportion of hydrophilic quartz minerals ending up in the concentrate is lower for HEDP, with only 1.9% quartz at a recovery of 21.5% compared to the 2.7% of quartz at a recovery of 24.9% when using SHMP. The paper contributes in general to understanding the complexity of the depressant responses in froth flotation.

Synthesis of Low Viscosity Polydimethylsiloxane Using Low Grade of Octamethylcyclotetrasiloxane

2021 ◽  
Vol 1028 ◽  
pp. 365-370
Author(s):  
Diba G Auliya ◽  
Soni Setiadji ◽  
Zulfi Mofa Agasa ◽  
Fitrilawati ◽  
Norman Syakir ◽  
...  
Keyword(s):  
Ring Opening ◽  
Raw Materials ◽  
Vitreoretinal Surgery ◽  
Production Costs ◽  
Low Grade ◽  
High Grade ◽  
High Quality ◽  
Low Viscosity ◽  
Polymerization Method

Polydimethylsiloxane (PDMS) has been widely used as a vitreous humour substitution in vitreoretinal surgery. Due to its limited availability and increasing domestic needs, the price of PDMS in Indonesia became very expensive. Previously, we reported the synthesized of PDMS from a high grade of monomer of 98% of Octamethylcyclotetrasiloxane (D4) and found that all PDMS samples produced high quality samples similar to that of commercial one. However, by considering the ease of obtaining raw materials and also the production costs, the synthesis of PDMS using monomer which easy to be found in Indonesia and low production costs is needed to be developed. Here, we reported the synthesis of PDMS using low grade of 96% of D4 in order to produce high quality of PDMS with low viscosity that can be used for vitreous humous substitution in vitreoretinal surgery. PDMS samples with low viscosity value of 0.94-1.35 Pa.s have been successfully synthesized from low grade of D4 and MM using ring-opening polymerization method. The yields of PDMS resulted in this research were in the range between 67.27% and 76.26%. From FTIR spectroscopy, it is found that all synthesized samples have structure and functional groups similar to PDMS using high grade of monomer of 98% Octamethylcyclotetrasiloxane (D4). From refractometer and surfgauge measurements, all samples have refractive index in the range of 1,4034-1,4040 and the value surface tension was 21 m.N/m.

Sign in / Sign up

Export Citation Format

Share Document