Simulation Analysis of Savonius Turbine with Self-Rotating Blades

2012 ◽  
Vol 614-615 ◽  
pp. 480-484
Author(s):  
Zhi Peng Tang ◽  
Ying Xue Yao ◽  
Liang Zhou ◽  
Jin Ming Wu ◽  
Bo Wen Yu

This paper analyzed the advantages of traditional Savonius (S-type) turbine and the reasons of its low efficiency, proposed a new type of turbine with self-rotating blades and surrounded by a rectifier, and studied the aerodynamic performance by numerical simulations. The turbine is composed of a rectifier and a rotor, the rectifier consists by straight and arc segments which can accelerate the wind speed and adjust the inflow wind angle. The self-rotating blade can reduce the impacted area acting on the leeward blade by wind and arm of the impact torque, therefore reduces the resistant torque of the blade, and the driving torque acting on the windward blade is almost the same with traditional S-type turbine, which can increase the overall driving torque. The result shows that the new turbine has the advantages as below: wide range of wind speed for effective working, high power coefficient (Cp), suitable for low wind speed aera etc. Although the flow field in S-type turbine is complex separating flow, the performance of the turbine proposed in this paper is improved and is better than traditional S-type turbine in numerical simulation which is worth for spreading.

2017 ◽  
Vol 30 (1) ◽  
pp. 91-107 ◽  
Author(s):  
Qingtao Song ◽  
Dudley B. Chelton ◽  
Steven K. Esbensen ◽  
Andrew R. Brown

This study presents an assessment of the impact of a March 2006 change in the Met Office operational global numerical weather prediction model through the introduction of a nonlocal momentum mixing scheme. From comparisons with satellite observations of surface wind speed and sea surface temperature (SST), it is concluded that the new parameterization had a relatively minor impact on SST-induced changes in sea surface wind speed in the Met Office model in the September and October 2007 monthly averages over the Agulhas Return Current region considered here. The performance of the new parameterization of vertical mixing was evaluated near the surface layer and further through comparisons with results obtained using a wide range of sensitivity of mixing parameterization to stability in the Weather Research and Forecasting (WRF) Model, which is easily adapted to such sensitivity studies. While the new parameterization of vertical mixing improves the Met Office model response to SST in highly unstable (convective) conditions, it is concluded that significantly enhanced vertical mixing in the neutral to moderately unstable conditions (nondimensional stability [Formula: see text] between 0 and −2) typically found over the ocean is required in order for the model surface wind response to SST to match the satellite observations. Likewise, the reduced mixing in stable conditions in the new parameterization is also relatively small; for the range of the gradient Richardson number typically found over the ocean, the mixing was reduced by a maximum of only 10%, which is too small by more than an order of magnitude to be consistent with the satellite observations.


2020 ◽  
Vol 9 (3) ◽  
pp. 383-392
Author(s):  
Khalid Mrigua ◽  
Abdelghani Toumi ◽  
Mounia Zemamou ◽  
Bader Ouhmmou ◽  
Yahya Lahlou ◽  
...  

The Savonius-conventional wind turbine is a class of wind turbines designed with a vertical axis. It has a good starting capacity and   an insensitivity to wind direction. It works relatively at low wind speed in an easy installation. Savonius wind turbine faces major drawbacks, including some of the low efficiency and high negative torque created by the returning blade. Many attempts have been undertaken to optimize the blade’s shape to increase the performance of these wind turbines. The vertical axis is still under development. The elliptical-blades with a cut angle equal 47.50° have recently shown enhanced performance. In this study, we investigate the effect of Elliptical-bladed multistage Savonius Rotors (rotor aspect ratio, stage aspect ratio) on the performance by means of numerical simulation. The results obtained by comparison of one, two, and three-stage rotors indicate that the maximum power coefficient increase with a number of the stages (for the rotors with similar RAR of 0.7). Moreover, for the rotors with similar SAR of 0.7, the two stages have the highest performance than others.©2020. CBIORE-IJRED. All rights reserved


Energies ◽  
2020 ◽  
Vol 13 (18) ◽  
pp. 4679
Author(s):  
Zhao Liu ◽  
Honglei Deng ◽  
Ruidong Peng ◽  
Xiangyang Peng ◽  
Rui Wang ◽  
...  

With the increase in electricity demand, the ampacity calculation based on the dynamic thermal rating (DTR) technology is increasingly significant for assessing and improving the power transfer capacity of the existing overhead conductors. However, the DTR models now available present some inadequacies in measurement techniques related to wind speed. Therefore, it is essential to propose a new model instead of wind speed measuring in DTR technology. In this paper, the influence analysis of various weather parameters on the conductor ampacity is carried out by using the real weather data. Based on the analysis, it is confirmed that the impact of wind speed is significant, especially in the case of the low wind speed. Moreover, an equivalent heat transfer (EHT) model for DTR technology is proposed instead of wind speed measuring. For this EHT model, the calculation of conductor ampacity is realized through investigating the correlation of heat losses between the heating aluminum (Al) ball and conductor. Finally, combined with the finite element method (FEM), the EHT model proposed in this paper is verified by the Institute of Electrical and Electronic Engineers (IEEE) standard. The results indicate that the error of the EHT model is less than 6% when employing the steady thermal behavior of the Al ball to calculate the ampacity. The EHT model is useful in the real-time thermal rating of overhead conductors. It can increase the utilization of overhead conductors while also avoiding the limitation of the existing measurement techniques related to wind speed.


Energies ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 2846 ◽  
Author(s):  
Xiaohang Wang ◽  
Wentong Chong ◽  
Kokhoe Wong ◽  
Liphuat Saw ◽  
Sinchew Poh ◽  
...  

The technical and economic features of a patented V-shape roof guide vane (VRGV) with a solar and wind power generation system mounted on an eco-roof system are presented in this paper. Moreover, this innovative VRGV was investigated on for the purpose of improving the performance of a vertical axis wind turbine (VAWT), which was installed on an eco-roof system to solve the low-efficiency power generation problem of the wind turbines under the condition of a low wind speed. This paper proposes a preliminary study for the performance of the VAWT with the VRGV on a building. This research used a mock-up building with a double slope roof, where a five straight-bladed VAWT was mounted and tested under two conditions, with and without the VRGV. From the comparative experiments, the self-starting performance and rotational speed of the VAWT mounted above a double slope roof with the VRGV have been significantly improved compared to the VAWT without the VRGV. Further, the power coefficient (Cp) of the VAWT can be augmented to about 71.2% increment due to the VRGV design. In addition, numerical simulations by computational fluid dynamics (CFD) were proposed to verify the augmented effect of the Cp of the VAWT under the influence of the VRGV in the experiment. Besides, economic estimation of the VRGV was conducted.


2010 ◽  
Vol 14 (12) ◽  
pp. 2643-2659 ◽  
Author(s):  
C. Cammalleri ◽  
M. C. Anderson ◽  
G. Ciraolo ◽  
G. D'Urso ◽  
W. P. Kustas ◽  
...  

Abstract. For open orchard and vineyard canopies containing significant fractions of exposed soil (>50%), typical of Mediterranean agricultural regions, the energy balance of the vegetation elements is strongly influenced by heat exchange with the bare soil/substrate. For these agricultural systems a "two-source" approach, where radiation and turbulent exchange between the soil and canopy elements are explicitly modelled, appears to be the only suitable methodology for reliably assessing energy fluxes. In strongly clumped canopies, the effective wind speed profile inside and below the canopy layer can strongly influence the partitioning of energy fluxes between the soil and vegetation components. To assess the impact of in-canopy wind profile on model flux estimates, an analysis of three different formulations is presented, including algorithms from Goudriaan (1977), Massman (1987) and Lalic et al. (2003). The in-canopy wind profile formulations are applied to the thermal-based two-source energy balance (TSEB) model developed by Norman et al. (1995) and modified by Kustas and Norman (1999). High resolution airborne remote sensing images, collected over an agricultural area located in the western part of Sicily (Italy) comprised primarily of vineyards, olive and citrus orchards, are used to derive all the input parameters needed to apply the TSEB. The images were acquired from June to October 2008 and include a relatively wide range of meteorological and soil moisture conditions. A preliminary sensitivity analysis of the three wind profile algorithms highlights the dependence of wind speed just above the soil/substrate to leaf area index and canopy height over the typical range of canopy properties encountered in these agricultural areas. It is found that differences among the models in wind just above the soil surface are most significant under sparse and medium fractional cover conditions (15–50%). The TSEB model heat flux estimates are compared with micro-meteorological measurements from a small aperture scintillometer and an eddy covariance tower collected over an olive orchard characterized by moderate fractional vegetation cover (≈35%) and relatively tall crop (≈3.5 m). TSEB fluxes for the 7 image acquisition dates generated using both the Massman and Goudriaan in-canopy wind profile formulations give close agreement with measured fluxes, while the Lalic et al. equations yield poor results. The Massman wind profile scheme slightly outperforms that of Goudriaan, but it requires an additional parameter accounting for the roughness sub-layer of the underlying vegetative surface. The analysis also suggests that within-canopy wind profile model discrepancies become important, in terms of impact on modelled sensible heat flux, only for sparse canopies with moderate vegetation coverage.


2017 ◽  
Vol 17 (14) ◽  
pp. 9019-9033 ◽  
Author(s):  
Thomas G. Bell ◽  
Sebastian Landwehr ◽  
Scott D. Miller ◽  
Warren J. de Bruyn ◽  
Adrian H. Callaghan ◽  
...  

Abstract. Simultaneous air–sea fluxes and concentration differences of dimethylsulfide (DMS) and carbon dioxide (CO2) were measured during a summertime North Atlantic cruise in 2011. This data set reveals significant differences between the gas transfer velocities of these two gases (Δkw) over a range of wind speeds up to 21 m s−1. These differences occur at and above the approximate wind speed threshold when waves begin breaking. Whitecap fraction (a proxy for bubbles) was also measured and has a positive relationship with Δkw, consistent with enhanced bubble-mediated transfer of the less soluble CO2 relative to that of the more soluble DMS. However, the correlation of Δkw with whitecap fraction is no stronger than with wind speed. Models used to estimate bubble-mediated transfer from in situ whitecap fraction underpredict the observations, particularly at intermediate wind speeds. Examining the differences between gas transfer velocities of gases with different solubilities is a useful way to detect the impact of bubble-mediated exchange. More simultaneous gas transfer measurements of different solubility gases across a wide range of oceanic conditions are needed to understand the factors controlling the magnitude and scaling of bubble-mediated gas exchange.


Author(s):  
László Daróczy ◽  
Mohamed H. Mohamed ◽  
Gábor Janiga ◽  
Dominique Thévenin

Wind energy represents nowadays a very important source of energy for many countries. It provides an efficient and effective solution to reduce fuel consumption as well as pollutant emissions. VAWTs (vertical axis wind turbines) were originally considered as very promising, before being superseded by the present, horizontal axis turbines. There is now a resurgence of interests for VAWTs, in particular Darrieus turbines. VAWTs like the H-rotor Darrieus turbine appear to be particularly promising for low wind speed conditions, but suffer from a low efficiency compared to horizontal axis turbines. Additionally, Darrieus turbines are not self-starting, which is a major drawback. The present paper introduces a new idea to improve the global performance of Darrieus rotors, relying on a slotted flap. Due to its low manufacturing costs and size, a two-bladed H-rotor with a radius of 2 meters was retained as a first application example. The blade airfoil relies on the S1046 profile, which was shown in previous studies to be superior under relevant operating conditions [1]. The solidity (Nc/R) of the rotor is kept at 0.25 for all the computations. In the first step a parametric geometry is created, where the end of the blade is converted into a slotted flap (with appropriate rounding). The main parameters are the distance between the main part of the blade and the flap (width of gap), the angle of the slot and the angle of the flap. In the second step a systematic analysis of the effect of those variables on the force and power coefficient is carried out using three-dimensional full factorial Design-of-Experiment with an in-house parameterization and optimization software. For each configuration, force and power coefficients are calculated for four different tip-speed ratios (including the value, where the S1046 profile without flap shows its maximal power coefficient). The evaluation of each configuration is performed using a commercial CFD software. The flow is assumed in this first study to be two-dimensional and unsteady. Turbulence intensities follow the relevant norms (DIN EN 61400). Finally the results are compared to each other and to the reference design (S1046 without flap) and conclusions are given regarding power coefficient and flap load.


Symmetry ◽  
2019 ◽  
Vol 12 (1) ◽  
pp. 18 ◽  
Author(s):  
Hani Muhsen ◽  
Wael Al-Kouz ◽  
Waqar Khan

This work aims at designing and optimizing the performance of a small Horizontal-Axis-Wind-Turbine to obtain a power coefficient (CP) higher than 40% at a low wind speed of 5 m/s. Two symmetric in shape airfoils were used to get the final optimized airfoil. The main objective is to optimize the blade parameters that influence the design of the blade since the small turbines are prone to show low performance due to the low Reynolds number as a result of the small size of the rotor and the low wind speed. Therefore, the optimization process will select different airfoils and extract their performance at the design conditions to find the best sections which form the optimal design of the blade. The sections of the blade in the final version mainly consist of two different sections belong to S1210 and S1223 airfoils. The optimization process goes further by investigating the performance of the final design, and it employs the blade element momentum theory to enhance the design. Finally, the rotor-design was obtained, which consists of three blades with a diameter of 4 m, a hub of 20 cm radius, a tip-speed ratio of 6.5 and can obtain about 650 W with a Power coefficient of 0.445 at a wind-speed of 5.5 m/s, reaching a power of 1.18 kW and a power coefficient of 0.40 at a wind-speed of 7 m/s.


1986 ◽  
Vol 108 (3) ◽  
pp. 246-251
Author(s):  
A. C. Hansen ◽  
T. E. Hausfeld

Pre-averaging is often applied to wind turbine test data to improve correlation between wind speed and power output data. In the past, trial and error or intuition have been used in the selection of pre-averaging time and researchers and institutions have differed widely in their pre-averaging practice. In this paper a standardized method is proposed for selection of the optimum pre-averaging time. The method selects an averaging time such that the test data are low-pass-filtered at the same frequency as the response frequency of the test wind turbine/anemometer system. A theoretial method is provided for estimation of the wind system transfer function as a function of the anemometer location, rotor moment of inertia, the stiffness of the connection between the rotor and the electrical grid, hub height, rotor speed and wind speed. The method is based in proven theory, repeatable, easy to use and applicable to a wide range of wind turbines and test conditions. Results of the transfer function predictions are compared with the measured response of two wind systems. Agreement between the predicted and measured response is completely adequate for the purposes of the method. Example results of calculated averaging times are presented for several wind turbines. In addition, a case study is used to demonstrate the dramatic effects of test design and data analysis methods on the results of a power coefficient measurement.


2020 ◽  
Vol 26 (4) ◽  
pp. 64-79
Author(s):  
Ahmed Saadi AlJarakh ◽  
Hussain Yousif Mahmood

As the prices of the fuel and power had fluctuated many times in the last decade and new policies appeared and signed by most of the world countries to eliminate global warming and environmental impact on the earth surface and humanity exciting, an urgent need appeared to develop the renewable energy harnessing technologies on the short-term and long-term and one of these promising technologies are the vertical axis wind turbines, and mostly the combined types. The purpose of the present work is to combine a cavity type Savonius with straight bladed Darrieus to eliminate the poor self-starting ability for Darrieus type and low performance for Savonius type and for this purpose, a three-bladed Darrieus type with symmetrical S1046 airfoil was tested experimentally and numerically at different wind speeds (4.5 m/s, 8 m/s and 10 m/s) and it showed a poor self-starting ability at low wind speed although its higher performance at high wind speed. However when adding the cavities in two setup configuration and testing it at the same conditions, it was found that when adding the cavities as reversed cups in the core of the turbine, the performance increased and the power coefficient reached a maximum value at 10 m/s wind speed and it was observed to be 0.0914 , but when the solidity increased by adding three cavities, the performance was higher at low wind speed (4.5 m/s) but it tragically decreased at higher wind speed which indicates that the performance depends on the solidity and the turbine configuration. On the other hand, the numerical simulation showed a good match with the experimental results although it under-predicted the performance.


Sign in / Sign up

Export Citation Format

Share Document