Effects of Cell-Wall Angle on the Mechanical Properties of Hexagonal Honeycombs

2013 ◽  
Vol 535-536 ◽  
pp. 377-380
Author(s):  
Ling Ling Hu ◽  
Tong Xi Yu
Keyword(s):  
Mechanical Properties ◽  
Cell Wall ◽  
Relative Density ◽  
Significant Influence ◽  
Absorption Capacity ◽  
Energy Absorption Capacity ◽  
Wall Angle ◽  
Dynamic Simulations ◽  
Crushing Strength ◽  
The Impact

The y-directional mechanical properties of hexagonal honeycombs with various cell-wall angles are explored. The results of both the quasi-static experiments and the dynamic simulations show that the cell-wall angle has a significant influence on the honeycombs’ mechanical properties, although the latter is dominated by the honeycombs’ relative density. This influence is weakened by the increase of the impact velocity. With retaining the honeycombs’ relative density as constant, the honeycomb with the cell-wall angle of about 45o exhibits the optimal crushing strength and energy absorption capacity.

Mechanical Response of Porous Copper Manufactured by Lost Carbonate Sintering Process

2007 ◽  
Vol 539-543 ◽  
pp. 1863-1867 ◽  
Author(s):  
X.F. Tao ◽  
Li Ping Zhang ◽  
Y.Y. Zhao
Keyword(s):  
Particle Size ◽  
Flexural Strength ◽  
Relative Density ◽  
Mechanical Response ◽  
Compaction Pressure ◽  
Absorption Capacity ◽  
Energy Absorption Capacity ◽  
Three Point Bending ◽  
Porous Copper ◽  
The Impact

This paper investigated the mechanical response of porous copper manufactured by LCS under three-point bending and Charpy impact conditions. The effects of the compaction pressure and K2CO3 particle size used in producing the porous copper samples and the relative density of the samples were studied. The apparent modulus, flexural strength and energy absorption capacity in three-point bending tests increased exponentially with increasing relative density. The impact strength was not markedly sensitive to relative density and had values within 7 – 9 kJ/m2 for the relative densities in the range 0.17 – 0.31. The amount of energy absorbed by a porous copper sample in the impact test was much higher than that absorbed in the three-point bending test, impling that loading strain rate had a significant effect on the deformation mechanisms. Increasing compaction pressure and increasing K2CO3 particle size resulted in significant increases in the flexural strength and the bending energy absorption capacity, both owing to the reduced sintering defects.

scholarly journals Static Mechanical Properties of Expanded Polypropylene Crushable Foam

Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 249
Author(s):  
Przemysław Rumianek ◽  
Tomasz Dobosz ◽  
Radosław Nowak ◽  
Piotr Dziewit ◽  
Andrzej Aromiński
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Strain Rate ◽  
Energy Absorption ◽  
Experimental Tests ◽  
Absorption Capacity ◽  
Strain Rates ◽  
Foam Density ◽  
Energy Absorption Capacity ◽  
Closed Cell

Closed-cell expanded polypropylene (EPP) foam is commonly used in car bumpers for the purpose of absorbing energy impacts. Characterization of the foam’s mechanical properties at varying strain rates is essential for selecting the proper material used as a protective structure in dynamic loading application. The aim of the study was to investigate the influence of loading strain rate, material density, and microstructure on compressive strength and energy absorption capacity for closed-cell polymeric foams. We performed quasi-static compressive strength tests with strain rates in the range of 0.2 to 25 mm/s, using a hydraulically controlled material testing system (MTS) for different foam densities in the range 20 g/dm3 to 220 g/dm3. The above tests were carried out as numerical simulation using ABAQUS software. The verification of the properties was carried out on the basis of experimental tests and simulations performed using the finite element method. The method of modelling the structure of the tested sample has an impact on the stress values. Experimental tests were performed for various loads and at various initial temperatures of the tested sample. We found that increasing both the strain rate of loading and foam density raised the compressive strength and energy absorption capacity. Increasing the ambient and tested sample temperature caused a decrease in compressive strength and energy absorption capacity. For the same foam density, differences in foam microstructures were causing differences in strength and energy absorption capacity when testing at the same loading strain rate. To sum up, tuning the microstructure of foams could be used to acquire desired global materials properties. Precise material description extends the possibility of using EPP foams in various applications.

Experimental Analysis of Aluminum Alloy Section Bars and their Mortise and Tenon Joints under Bending Load

2011 ◽  
Vol 415-417 ◽  
pp. 2338-2344
Author(s):  
Xin Shen Huang ◽  
Qun Gao ◽  
Zhi Jian Zong
Keyword(s):  
Mechanical Properties ◽  
Aluminum Alloy ◽  
Energy Absorption ◽  
Experimental Analysis ◽  
Absorption Capacity ◽  
Main Section ◽  
Bending Properties ◽  
Energy Absorption Capacity ◽  
Bending Load ◽  
Mortise And Tenon

Different laid modes of aluminum alloy section bars and their mortise and tenon joints were bending tested, and their mechanical properties were compared, in order to research on the influence that forming a mortise and tenon joint brought to the original bars. Opening a hole laterally and inserting another shorter bar in the hole changed the bending properties and energy absorption capacity of the original bar. In horizontal laid mode, the mortise and tenon joint was weaker than the original bar when bearing bending load, but it was stronger in vertical laid mode. Weld beads of the mortise and tenon joints were strong enough to maintain the structure integrality before the main section bars were destroyed by load.

Influence of Fibre Treatment and Matrix Modification on Mechanical Properties of Flax Fibre Reinforced Mortars after Freeze/Thaw Cycles

2022 ◽  
Author(s):  
Bojan Poletanovic ◽  
Katalin Kopecsko ◽  
Ildikó Merta
Keyword(s):  
Mechanical Properties ◽  
Energy Absorption ◽  
Linseed Oil ◽  
Absorption Capacity ◽  
Flax Fibre ◽  
Energy Absorption Capacity ◽  
Freeze Thaw ◽  
Flax Fibres ◽  
Matrix Modification ◽  
Compressive And Flexural Strengths

The aim of this study was to examine the influence of flax fibre protection with the linseed oil and a matrix modification with cement substitution with metakaolin (in 10wt% and 15wt%) on the mechanical properties of cement-based mortars under severe environmental conditions of freeze/thaw cycles. Cement-based mortars (with the dimension of 40x40x160 mm3) were reinforced by 10mm long discrete flax fibres (Linumusitatissimum) and exposed to 51 freeze/thaw cycles under laboratory condition. Their compressive and flexural strengths, as well as specific energy absorption capacity were measured after freeze/thaw cycles and compared to the results of mortars cured for same time in water. Under freeze/thaw cycles mortars reinforced with linseed oil-treated fibres showed the same range of degradation of the compressive and flexural strengths, however, a more pronounced degradation of energy absorption capacity compared to non-treated fibre reinforced mortars was observed. The matrix modification, by partial cement substitution with metakaolin showed optimistic results under freeze/thaw cycles. The compressive strength when cement was partially substituted with metakaolin (in both dosages) increased whereas the flexural strength was slightly lower in case of 10wt% substitution and markedly lower under higher (15wt%) cement substitution. The most relevant is that the decrease of the energy absorption capacity of the fibre reinforced mortar was completely prevented when cement was substituted with metakaolin. It is shown that the energy absorption of the non-treated fibre reinforced mortars increases by 27% when cement was substituted with metakaolin (both 10wt% and 15wt%).

3D-Printed Bio-inspired Zero Poisson’s Ratio Graded Metamaterials with High Energy Absorption Performance

2022 ◽  
Author(s):  
Ramin Hamzehei ◽  
Ali Zolfagharian ◽  
Soheil Dariushi ◽  
Mahdi Bodaghi
Keyword(s):  
Cell Wall ◽  
Energy Absorption ◽  
Poisson’S Ratio ◽  
High Energy ◽  
Absorption Capacity ◽  
Poisson's Ratio ◽  
Base Pairs ◽  
Energy Absorption Capacity ◽  
Static Compression ◽  
Unit Cells

Abstract This study aims at introducing a number of two-dimensional (2D) re-entrant based zero Poisson’s ratio (ZPR) graded metamaterials for energy absorption applications. The metamaterials’ designs are inspired by the 2D image of a DNA molecule. This inspiration indicates how a re-entrant unit cell must be patterned along with the two orthogonal directions to obtain a ZPR behavior. Also, how much metamaterials’ energy absorption capacity can be enhanced by taking slots and horizontal beams into account with the inspiration of the DNA molecule’s base pairs. The ZPR metamaterials comprise multi-stiffness unit cells, so-called soft and stiff re-entrant unit cells. The variability in unit cells’ stiffness is caused by the specific design of the unit cells. A finite element analysis (FEA) is employed to simulate the deformation patterns of the ZPRs. Following that, meta-structures are fabricated with 3D printing of TPU as hyperelastic materials to validate the FEA results. A good correlation is observed between FEA and experimental results. The experimental and numerical results show that due to the presence of multi-stiffness re-entrant unit cells, the deformation mechanisms and the unit cells’ densifications are adjustable under quasi-static compression. Also, the structure designed based on the DNA molecule’s base pairs, so-called structure F''', exhibits the highest energy absorption capacity. Apart from the diversity in metamaterial unit cells’ designs, the effect of multi-thickness cell walls is also evaluated. The results show that the diversity in cell wall thicknesses leads to boosting the energy absorption capacity. In this regard, the energy absorption capacity of structure ‘E’ enhances by up to 33% than that of its counterpart with constant cell wall thicknesses. Finally, a comparison in terms of energy absorption capacity and stability between the newly designed ZPRs, traditional ZPRs, and auxetic metamaterial is performed, approving the superiority of the newly designed ZPR metamaterials over both traditional ZPRs and auxetic metamaterials.

Development of Parametric Kelvin Structures will Closed Cells

2016 ◽  
Vol 254 ◽  
pp. 49-54 ◽  
Author(s):  
Dan Andrei Şerban ◽  
Emanoil Linul ◽  
Sorin Sărăndan ◽  
Liviu Marşavina
Keyword(s):  
Mechanical Properties ◽  
Cell Wall ◽  
Relative Density ◽  
Material Properties ◽  
Cell Diameter ◽  
Rigid Polyurethane Foam ◽  
Loading Direction ◽  
Convergence Study ◽  
Simulation Results ◽  
Mesh Convergence

This work presents the design of a parametric Kelvin structure in which the relative density of the geometry can be varied by adjusting three parameters: cell diameter, cell wall thickness and cell chamfer radius, the structure consistsing of a tessellation of hollow truncated octahedral. The developed model was evaluated in terms of compressive stiffness for the case of a rigid polyurethane foam of 0.256 relative density. Three models were analyzed in order to determine the influence of geometric characteristics on mechanical properties: a model that presented no chamfer a model that presented a medium-sized chamfer and a model that presented a large chamfer. A mesh convergence study was performed which analyzed the results in terms of accuracy and time expenses for three element sizes for both linear and quadratic elements. Due to the orthotropic nature of the model, its response on both possible loading directions was investigated. Simulation results were compared with experimental results and yielded accurate results for one loading direction, when using the material properties for solid polyurethane described in literature.

High and Low Speed Impact Characteristics of Nanocomposites

2015 ◽  
Vol 1105 ◽  
pp. 62-66 ◽  
Author(s):  
Saud Aldajah ◽  
Yousef Haik ◽  
Kamal Moustafa ◽  
Ammar Alomari
Keyword(s):  
High Speed ◽  
Impact Resistance ◽  
Absorption Capacity ◽  
Impact Testing ◽  
Energy Absorption Capacity ◽  
Low Speed ◽  
High Speed Impact ◽  
Bulletproof Vest ◽  
Impact Characteristics ◽  
The Impact

Nanocomposites attracted the attention of scientists due to their superior mechanical, thermal, chemical and electrical properties. This research studied the impact of adding carbon nanotubes (CNTs) to the woven Kevlar laminated composites on the high and low speed impact characteristics. Different percentages of CNTs were added to the woven Kevlar-Vinylester composite materials. An in-house developed drop weight testing apparatus was utilized for the low speed impact testing. Two different concentrations of the CNTs were added to a 15-layer woven Kevlar laminates, 0.32 wt% and 0.8 wt%. The results showed that: The 0.32 wt % CNT sample enhanced the interlaminar strength of the composite without enhancing the energy absorption capacity whereas, the 0.8 wt % CNT sample did not improve the impact resistance of the Kevlar composite.For the high speed impact tests, a bulletproof vest was prepared using woven Kevlar, resin, and CNTs at 1.5 w% percentage. The ballistic shooting was carried out by a professional shooter using a 30 caliber and 9 mm bullets for the tests. The CNT bulletproof sample bounced back the 30 caliber copper alloy bullet with no penetration.

scholarly journals Effect of Disinfectants on Mechanical Properties of Orthodontic Acrylics

2019 ◽  
Vol 2019 ◽  
pp. 1-10 ◽  
Author(s):  
Tobias Bensel ◽  
Jens J. Bock ◽  
Anne Kebernik ◽  
Christin Arnold ◽  
Sonia Mansour ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Flexural Strength ◽  
Significant Influence ◽  
Colour Change ◽  
Water Disinfection ◽  
Distilled Water ◽  
Micro Hardness ◽  
Average Roughness ◽  
The Impact

Objective. Infection control protocols in dentistry dictate that orthodontic acrylics have to be disinfected. No specific products for orthodontic acrylics are available. The objective of this study was to investigate the influence of chemical disinfectants on mechanical properties of orthodontic acrylics.Materials and Methods. 260 test specimens of two cold-curing orthodontic acrylics were manufactured. Three chemical disinfecting agents were tested: Impresept, D050 Instru-Gen, and Stammopur DR. Test specimens were stored in distilled water and divided into test groups. E-Modulus, flexural strength, macro hardness, micro hardness, average roughness, and colour change were measured.Results. Disinfection agents showed no significant influence on E-modulus. Values ranged from 1783.80 ± 163.80 MPa (Forestacryl colourless) to 2474.00 ± 135.00 MPa (Orthocryl green) after storage in distilled water. Disinfection agents performed no significant influence on flexural strength. Values ranged from 18.64±1.59 N/mm2(Forestacryl colourless) to 25.64 ± 1.43 N/mm2(Orthocryl green) after storage in distilled water. Orthocryl colourless showed a reduction of the macro hardness after disinfection (Stammopur DR (p≤0.001), D050 Instru-Gen (p≤0.037)). Disinfection of Orthocryl green with D050 Instru-Gen (p<0.001) and Forestacryl colourless with Impresept (p≤0.001) led to a reduction of macro hardness. Micro hardness of Orthocryl colourless altered significantly after disinfection with D050 Instru-Gen (p≤0.001). Micro hardness of Forestacryl colourless increased (Impresept (p≤0.039)) and decreased (Stammopur DR (p≤0.006) Instru-Gen (p≤0.001)) after disinfection. Average roughness did not change significantly (Orthocryl colourless). Forestacryl colourless performed a significant change after disinfection with Stammopur DR (p≤0.05). This is also true for the disinfection of Orthocryl green and Forestacryl pink with Instru-Gen (p≤0.05). Disinfection performed no significant influence on colour change. ΔE-values were in a range of 1 to 2.Conclusions. Some orthodontic acrylics disinfection caused significant changes of determined parameters. Changes were specific for the applied disinfectant and tested orthodontic acrylic. Further studies should verify the impact of long-term disinfection intervals. Thus, from manufacturers of orthodontic acrylics recommendations for appropriate disinfectants would be desirable.

Study on Ballistic Characteristics of Glass-Epoxy-Rubber Sandwiches

2020 ◽  
Vol 978 ◽  
pp. 245-249
Author(s):  
Rajole Sangamesh ◽  
Hiremath Shivashankar ◽  
K.S. Ravishankar ◽  
S.M. Kulkarni
Keyword(s):  
Natural Rubber ◽  
Energy Absorption ◽  
Experimental Validation ◽  
Absorption Capacity ◽  
Velocity Variation ◽  
Ballistic Limit ◽  
Ballistic Performance ◽  
Energy Absorption Capacity ◽  
Ballistic Limit Velocity ◽  
The Impact

This article focuses on the Finite Element (FE) analysis of the ballistic performance of the polymer composites consisting of natural rubber (NR), glass-epoxy (GE) and glass-rubber-epoxy (GRE) sandwich of different thicknesses (3, 6 and 9 mm) under the impact of the conical nose projectile for a velocity variation of (180, 220 and 260 m / s). FE modeling was carried out in direction to forecast the energy absorption, ballistic limit velocity and failure damage mode of the target materail. The significant influence of thickness, interlayer and sandwiching effect was studied: the lowest ballistic limit was obtained for 3 mm thick GE. Energy absorption capacity of GRE sandwich was highest among the natural rubber and GE. In future, the work can be extended for the experimental validation purpose, so that these polymer composite materials could be utilized to defence sector for bullet-proofing.

Factorial Experimental Planning Applied for Evaluated Effect of Matrix Temperature and Screw Rotation Speed of Extrusion in Mechanical Properties and Dimensional Changes in PVC Pipes

2018 ◽  
Vol 930 ◽  
pp. 241-247
Author(s):  
J. Fiori Júnior ◽  
Raquel Piletti ◽  
J. Ilha ◽  
M. Pierini ◽  
Humberto Gracher Riella ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Significant Influence ◽  
Impact Resistance ◽  
Dimensional Change ◽  
Extrusion Process ◽  
Process Conditions ◽  
Dimensional Variation ◽  
Pvc Pipe ◽  
The Impact

This study evaluated the effects of temperature and speed screw rotation of rigid recycled PVC pipe extrusion process on mechanical properties and dimensional variation. In developing the experiments were used the factorial design method type 2k. Were studied the influence of process variables on the properties of impact resistance, dimensional change and tensile strength of PVC pipe. From this study, it was possible to define the best extrusion process conditions with a point of view on the best properties of PVC pipes. The results indicated that the screw rotation has a significant influence on the impact property. For the dimensional variation, the extrusion temperature had a significant influence. There is no significant statistical values for the tensile strength in the studied variables.

Sign in / Sign up

Export Citation Format

Share Document