Characteristic of Titania Photocatalyst Fine Particles Added Zirconia

2005 ◽  
Vol 486-487 ◽  
pp. 33-36 ◽  
Author(s):  
Eiji Watanabe ◽  
Makoto Takagi ◽  
Mitsuharu Fukaya ◽  
Hiroshi Taoda
Keyword(s):  
Fine Particles ◽  
Visible Range ◽  
Ultraviolet Rays ◽  
Visible Radiation ◽  
The Past ◽  
Bleaching Test ◽  
New Type ◽  
The Difference ◽  
Titania Photocatalyst ◽  
The Stability

Recently, the titania photocatalyst has been widely used in the environmental fields. However, because the past titania photocatalyst used only the range of ultraviolet rays, the usage has been limited. We attempted to develop a new type of titania photocatalyst that activates to respond not only in the ultraviolet rays region but also in the visible radiation region. The titania photocatalyst fine particles that zirconium oxide was uniformly added in the titania fine particles, and introduced simultaneously nitrogen into the crystal lattice in addition were synthesized. It was showed the high photo-absorption ability of the titania photocatalyst added the zirconium compared with not done by the absorption spectrum. Furthermore, it was found that the titania fine particles that introduced nitrogen colored to yellow, had also the high photo-absorption ability in the visible range of 600nm to 400nm in addition to the range of ultraviolet rays. It was thought that this depended on the reason based on the difference of the amount of the nitrogen introduction in the titania that originated in the zirconium. Moreover, it was compared the stability maintenance for the titania introduced nitrogen with it not done by the bleaching test of heating. As a result, the stability of the titania added the zirconium was higher than not added.

Impact Evaluation to Human Body Skin of Titania Photocatalyst Fine Particles

2006 ◽  
Vol 510-511 ◽  
pp. 38-41
Author(s):  
Eiji Watanabe ◽  
Mitsuharu Fukaya ◽  
Hiroshi Taoda
Keyword(s):  
Carbon Dioxide ◽  
Human Body ◽  
Impact Evaluation ◽  
Fine Particle ◽  
Fine Particles ◽  
Test Method ◽  
Artificial Skin ◽  
Evaluation Test ◽  
The Difference ◽  
Titania Photocatalyst

The establishment of evaluation test method of the titania photocatalyst fine particle impact to human body skin was attempted. In this method, the amount of emergence of carbon dioxide, which was expected one of the generation products from the artificial skin according to the titania photocatalyst fine particles activity, was identified and measured by the gas analyzer. It was found that the amount of the carbon dioxide evolution from the artificial skin was different according to the difference of the particle size of the titania photocatalyst fine particle.

Bifurcation to fronts due to delay

2010 ◽  
Vol 368 (1911) ◽  
pp. 483-493 ◽  
Author(s):  
T. Erneux ◽  
G. Kozyreff ◽  
M. Tlidi
Keyword(s):  
Global Bifurcation ◽  
Propagation Speed ◽  
Radial Symmetry ◽  
Delayed Feedback Control ◽  
The Past ◽  
The Difference ◽  
The Stability ◽  
System Variables ◽  
Time Delayed Feedback ◽  
Moving Front

The stability of a steady-state front (kink) subject to a time-delayed feedback control (TDFC) is examined in detail. TDFC is based on the use of the difference between system variables at the current moment of time and their values at some time in the past. We first show that there exists a bifurcation to a moving front. We then investigate the limit of large delays but weak feedback and obtain a global bifurcation diagram for the propagation speed. Finally, we examine the case of a two-dimensional front with radial symmetry and determine the critical radius above which propagation is possible.

scholarly journals Numerical Analysis of a New Type of Dishwasher Pump for Different Rotation Speeds of the Volute

2022 ◽  
Vol 9 ◽  
Author(s):  
Chao Ning ◽  
Yalin Li ◽  
Ping Huang ◽  
Hui Xu ◽  
Feng Zheng
Keyword(s):  
Flow Field ◽  
Pressure Pulse ◽  
Transient Flow ◽  
Radial Force ◽  
Vector Distribution ◽  
New Type ◽  
Outflow Region ◽  
The Difference ◽  
The Stability ◽  
The Time Domain

The interaction between impeller and volute produces a complex and unsteady water flow. It involves the interference of the non-uniform flow (such as the impeller’s jet wake and a secondary flow). In this paper, the transient flow in a new type of dishwasher pump is investigated numerically. In addition, pressure measurements are used to validate the numerical method, and the simulation results agree well with the experiment. Three schemes, 0 rpm (revolutions per minute)/30 rpm/60 rpm, of volute speeds are investigated. Multiple monitoring points are set at different positions of the new dishwasher pump to record pressure-pulse signals. In addition, frequency signals are obtained using a Fast Fourier Transform, which is then used to analyze the effect of the volute tongue and the outflow of the impeller. The radial force on the principal axis is recorded, and the schemes with different rotation speeds of volute are compared. The results show that the volute speed has only a small effect on the pump performance. In addition, the speed of the volute mainly affects the flow field in the transition section located between impeller and volute. The difference of the flow field in the impeller depends on the relative position between the impeller and the volute. The time domain curve for the pressure pulse is periodic, and there is a deviation between the peak for the schemes in the outflow region. In the frequency domain, the characteristic frequency equals the blade passing frequency. In the outflow region, the effect of the volute speeds increases with increasing volute speed. For the radial force, the rotating volute strengthens the fluctuation of the radial force, which affects the operational stability of the pump. The shape of the vector distribution is most regular for the 30 rpm scheme, which indicates that the stability of the pump is the highest. This paper can be used to improve both the control and selection of volute speeds.

Use of a Lyophilized Reference Plasma to Compare Coagulation Test Procedures

1975 ◽  
Vol 34 (02) ◽  
pp. 426-444 ◽  
Author(s):  
J Kahan ◽  
I Nohén
Keyword(s):  
Oral Anticoagulant Therapy ◽  
Repeated Measurements ◽  
Test Procedures ◽  
Coagulation Activity ◽  
Close Relationship ◽  
Measured Activity ◽  
Test Materials ◽  
The Difference ◽  
The Stability ◽  
The One

SummaryIn 4 collaborative trials, involving a varying number of hospital laboratories in the Stockholm area, the coagulation activity of different test materials was estimated with the one-stage prothrombin tests routinely used in the laboratories, viz. Normotest, Simplastin-A and Thrombotest. The test materials included different batches of a lyophilized reference plasma, deep-frozen specimens of diluted and undiluted normal plasmas, and fresh and deep-frozen specimens from patients on long-term oral anticoagulant therapy.Although a close relationship was found between different methods, Simplastin-A gave consistently lower values than Normotest, the difference being proportional to the estimated activity. The discrepancy was of about the same magnitude on all the test materials, and was probably due to a divergence between the manufacturers’ procedures used to set “normal percentage activity”, as well as to a varying ratio of measured activity to plasma concentration. The extent of discrepancy may vary with the batch-to-batch variation of thromboplastin reagents.The close agreement between results obtained on different test materials suggests that the investigated reference plasma could be used to calibrate the examined thromboplastin reagents, and to compare the degree of hypocoagulability estimated by the examined PIVKA-insensitive thromboplastin reagents.The assigned coagulation activity of different batches of the reference plasma agreed closely with experimentally obtained values. The stability of supplied batches was satisfactory as judged from the reproducibility of repeated measurements. The variability of test procedures was approximately the same on different test materials.

Pengoptimalan Air Leri dalam Pembuatan Sabun Pembersih Wajah Alami yang Ekonomis

2017 ◽  
Vol 3 (1) ◽  
Author(s):  
Rahmawati Rahmawati ◽  
Trimayasari Trimayasari ◽  
Ghozali Akhmad Mustaqim ◽  
Wening Dwi Prastiwi ◽  
Emas Agus Prastyo Wibowo
Keyword(s):  
Amino Acids ◽  
Fine Particles ◽  
Hard Water ◽  
Essential Amino Acids ◽  
Ultraviolet Rays ◽  
Starch Granules ◽  
Facial Skin ◽  
Skin Cells ◽  
The Face ◽  
Made In

AbstractSoap facial cleanser is needed to keep the facial skin to keep them clean and healthy. The purpose of this study to make soap cleanser with natural materials such as hard water deposits leri. This is because the use of leri water starch or starch granules of fine particles contained in water leri dansel dust can shed the dead skin on the face because of the essential amino acids contained can regenerate skin cells. In addition, water leri can brighten the face because the leri water oryzanol contain substances that can update the development and formation of the pigment melanin, which is effectively to ward off ultraviolet rays. The process of making soap using the principle of saponification reaction, namely the reaction between the oil and the KOH/NaOH. Facial cleansing soap made in this study is solid soap. Based on the results of quality test, soap solid leri water has a pH of 11.1, saponification number is 33, the water content of 46% as well as respondents to the test aspects of aroma and foam shows good results so this water leri treatment can be an alternative solution to prevent the use of soap facial cleansers that contain harmful chemicals. Keywords: air leri, soap cleanser, saponification  AbstrakSabun pembersih wajah sangat diperlukan untuk menjaga kulit wajah agar tetap bersih dan sehat. Tujuan dari penelitian ini untuk membuat sabun pembersih wajah dengan bahan alami berupa endapan air leri. Penggunaan air leri ini dikarenakan butiran partikel starch atau pati halus yang terdapat dalam air leri dapat merontokkan debu dansel kulit mati pada wajah karena asam amino esensial yang terkandung dapat meregenerasi sel-sel kulit. Selain itu, air leri dapat mencerahkan wajah karena air leri mengandung zat oryzanol yang dapat memperbarui perkembangan dan pembentukan pigmen melanin, yang efektif guna menangkal sinar ultraviolet. Proses pembuatan sabun menggunakan prinsip reaksi saponifikasi, yaitu reaksi antara minyak dan KOH/NaOH. Sabun pembersih wajah yang dibuat dalam penelitian ini ialah sabun padat. Berdasarkan hasil uji mutu, sabun air leri padat memiliki pH 11,1, angka penyabunan sebesar 33 kadar air 46 kadar air 46 % serta uji responden terhadap aspek aroma dan busa yang menunjukkan hasil cukup baik sehingga pengolahan air leri ini dapat menjadi solusi alternative untuk mencegah penggunaan sabun pembersih wajah yang mengandung bahan kimia berbahaya. Kata kunci: air leri, sabun pembersih wajah, saponifikasi 

Smart Estimation Ver-H.1.0

2018 ◽  
Author(s):  
Sigit Haryadi
Keyword(s):  
Sample Size ◽  
Confidence Level ◽  
Time Span ◽  
Regression Equation ◽  
Weight Factor ◽  
The Past ◽  
Level Of Confidence ◽  
The Future ◽  
Future Value ◽  
The Difference

We cannot be sure exactly what will happen, we can only estimate by using a particular method, where each method must have the formula to create a regression equation and a formula to calculate the confidence level of the estimated value. This paper conveys a method of estimating the future values, in which the formula for creating a regression equation is based on the assumption that the future value will depend on the difference of the past values divided by a weight factor which corresponding to the time span to the present, and the formula for calculating the level of confidence is to use "the Haryadi Index". The advantage of this method is to remain accurate regardless of the sample size and may ignore the past value that is considered irrelevant.

In the stability of paints and varnishes for protective and decorative wood finish

2016 ◽  
Author(s):  
Ю.И. Цой
Keyword(s):  
Organic Solvents ◽  
Evaluation Criteria ◽  
Ternary Systems ◽  
Solubility Parameters ◽  
Formaldehyde Resin ◽  
Film Forming ◽  
The Difference ◽  
Molecular Forces ◽  
The Stability ◽  
Thermodynamic Interaction

Задача получения однородного состава ЛКМ сводится к правильному выбору пленкообразователей и соответствующих растворителей и, в случае необходимости, разбавителей и добавок. На основе положений теории растворимости была проведена оценка совместимости компонентов и стабильности таких систем. Критериями оценки были приняты параметры растворимости и термодинамического взаимодействия. Исследовали совместимость алкидных лаков с аминоформальдегидными смолами в бутаноле, и результаты этих исследований представлены в треугольной фазовой диаграмме. Для оценки совместимости смол по результатам расчета параметров термодинамического взаимодействия были построены спинодали для тройных систем. Как показывает анализ результатов проведенных исследований, даже при большой разности ?? = |?12 – ?13| = 0,2 наблюдается небольшая область несовместимости. С уменьшением разности ?? область несовместимости сужается. При ?23 > ?с область несовместимости расширяется как для ? = 0,2, так и для ?? = 0,1 и ?? = 0. Таким образом, для таких систем на совместимость компонентов, в первую очередь, влияет их взаимодействие между собой – чем оно больше, тем лучше они совместимы. Проведенные исследования показали, что парциальные параметры растворимости, учитывающие природу когезионных сил, более объективно характеризуют растворимость пленкообразующих смол в органических растворителях, чем их общий параметр растворимости. Растворимость пленкообразующих алкидных и этерифицированных аминоформальдегидных смол в органических растворителях обусловлена термодинамическим взаимодействием молекулярных сил различной природы. Стабильность смеси алкидной и этерифицированной аминоформальдегидной смолы в бутаноле обусловлена в большей степени термодинамическим взаимодействием молекулярных сил; при этом степень бутанолизации меламиноформальдегидной смолы оказывает наибольшее влияние на стабильность cистемы. Проведенные исследования по стабильности лакокрасочных смесей из различных пленкообразующих смол на основе рассмотренных критериев оценки могут быть использованы для совершенствования технологии защитно-декоративной отделки древесины. The problem of obtaining a homogeneous composition of the coatings is reduced to the proper selection of film-forming agents, and diluent and, if appropriate, diluents and additives. On the basis of the theory of solubility, we have carried out the assessment of the compatibility of the components and stability of such systems. The evaluation criteria were adopted the parameters of the solubility and thermodynamic interaction. Researched the compatibility with alkyd varnishes aminoformaldehyde resin in butanol, and the results of these studies are presented in the triangular phase diagram. To evaluate the compatibility of the resins according to the results of calculation of thermodynamic parameters of interaction were built spinodal for ternary systems. As the analysis of the results of the studies, even when the difference ??|?12 – ?13| = 0,2 there is a small area of incompatibility. With the decrease of the difference ? ? region incompatibility narrows. When ?23> ?с region incompatibility extends to ?? = 0,2, and for ?? = 0.1 and ?? = 0. Thus, for such systems, compatibility of components, primarily, affects their interaction with each other – the further away it is, the better they are compatible. Studies have shown that the partial solubility parameters, which take into account the nature of cohesive forces, more objectively characterize the solubility of film-forming resins in organic solvents than their total solubility parameter. The solubility and film-forming aminoformaldehyde esterified alkyd resins in organic solvents due to thermodynamic interaction of molecular forces of different nature. Тhe stability of the mixture and aminoformaldehyde esterified alkyd resin in butanol is generated largely by thermodynamic forces of molecular interaction; the degree of butanolate melamine-formaldehyde resin has the greatest effect on the stability of the system. Conducted research on the stability of the paint mixtures of various film-forming resins on the basis of the evaluation criteria can be used to improve the technology of protective and decorative wood finish.

Stability and Folding of the Unusually Stable Hemoglobin from Synechocystis is Subtly Optimized and Dependent on the Key Heme Pocket Residues.

2020 ◽  
Vol 27 ◽  
Author(s):  
Sheetal Uppal ◽  
Mohd. Asim Khan ◽  
Suman Kundu
Keyword(s):  
Molten Globule ◽  
Life Forms ◽  
Model System ◽  
Heme Pocket ◽  
The Past ◽  
Specific Manner ◽  
Delivery Vehicles ◽  
The Stability ◽  
Key Residues ◽  
Synechocystis Sp

Aims: The aim of our study is to understand the biophysical traits that govern the stability and folding of Synechocystis hemoglobin, a unique cyanobacterial globin that displays unusual traits not observed in any of the other globins discovered so far. Background: For the past few decades, classical hemoglobins such as vertebrate hemoglobin and myoglobin have been extensively studied to unravel the stability and folding mechanisms of hemoglobins. However, the expanding wealth of hemoglobins identified in all life forms with novel properties, like heme coordination chemistry and globin fold, have added complexity and challenges to the understanding of hemoglobin stability, which has not been adequately addressed. Here, we explored the unique truncated and hexacoordinate hemoglobin from the freshwater cyanobacterium Synechocystis sp. PCC 6803 known as “Synechocystis hemoglobin (SynHb)”. The “three histidines” linkages to heme are novel to this cyanobacterial hemoglobin. Objective: Mutational studies were employed to decipher the residues within the heme pocket that dictate the stability and folding of SynHb. Methods: Site-directed mutants of SynHb were generated and analyzed using a repertoire of spectroscopic and calorimetric tools. Result: The results revealed that the heme was stably associated to the protein under all denaturing conditions with His117 playing the anchoring role. The studies also highlighted the possibility of existence of a “molten globule” like intermediate at acidic pH in this exceptionally thermostable globin. His117 and other key residues in the heme pocket play an indispensable role in imparting significant polypeptide stability. Conclusion: Synechocystis hemoglobin presents an important model system for investigations of protein folding and stability in general. The heme pocket residues influenced the folding and stability of SynHb in a very subtle and specific manner and may have been optimized to make this Hb the most stable known as of date. Other: The knowledge gained hereby about the influence of heme pocket amino acid side chains on stability and expression is currently being utilized to improve the stability of recombinant human Hbs for efficient use as oxygen delivery vehicles.

Stability and mutual impact of perception of parental pressure and infants' social support – A study based on the difference between employment status and household income

2021 ◽  
pp. 002072092199705
Author(s):  
Yong Wang
Keyword(s):  
Household Income ◽  
Employment Status ◽  
Working Mothers ◽  
Social Research ◽  
Research Report ◽  
Parental Pressure ◽  
Income Levels ◽  
Significant Difference ◽  
The Difference ◽  
The Stability

The purpose of this study is to explore the stability and interaction between parental pressure and social research report, as well as the role of employment status and family income levels in this process. This study used a special study on Korean children (PSKC) 2–4 waves. Use t-test, correlation and autoregressive cross-delay modeling to analyze the data. The main findings of this study are: First, over time, parental pressure and mother’s social research report are consistent. Secondly, the pressure of motherhood and childcare has an obvious lagging effect on upbringing, and vice versa. Third, there is no significant difference between working mothers and non-working mothers in terms of the stability of working parents' pressure, social research report and social research report for children's pressure channels. However, parental pressure can only predict the social research report of working mothers. Fourth, there is no significant difference between the stability and interaction of these two structures in household income levels. In short, the results show that, over time, parental pressure is consistent with mother’s social research report. The results also show that there is a significant cross-lag effect between the mothers’ perceptions of mutual pressure analysis. In the process from parental pressure to social research report, I found the difference between working and non-working mothers. The advantage of this study is that the expected longitudinal design was adopted during infancy and the priority between the two structures can be considered. The results of this study can be used as a source of intervention plans to help parents withstand severe parenting pressure and lack of social research report.

scholarly journals Copper Phyllosilicates-Derived Catalysts in the Production of Alcohols from Hydrogenation of Carboxylates, Carboxylic Acids, Carbonates, Formyls, and CO2: A Review

Catalysts ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 255
Author(s):  
Dien-Thien To ◽  
Yu-Chuan Lin
Keyword(s):  
Carboxylic Acids ◽  
Catalytic Performance ◽  
Spatial Effect ◽  
Synthesis Methods ◽  
The Past ◽  
Surface Areas ◽  
Preparation Conditions ◽  
Remedial Actions ◽  
The Stability ◽  
Size Interaction

Copper phyllosilicates-derived catalysts (CuPS-cats) have been intensively explored in the past two decades due to their promising activity in carbonyls hydrogenation. However, CuPS-cats have not been completely reviewed. This paper focuses on the aspects concerning CuPS-cats from synthesis methods, effects of preparation conditions, and dopant to catalytic applications of CuPS-cats. The applications of CuPS-cats include the hydrogenation of carboxylates, carboxylic acids, carbonates, formyls, and CO2 to their respective alcohols. Besides, important factors such as the Cu dispersion, Cu+ and Cu0 surface areas, particles size, interaction between Cu and supports and dopants, morphologies, and spatial effect on catalytic performance of CuPS-cats are discussed. The deactivation and remedial actions to improve the stability of CuPS-cats are summarized. It ends up with the challenges and prospective by using this type of catalyst.

Sign in / Sign up

Export Citation Format

Share Document