Mechanical Properties and Microstructure of Mg-Zn-Y Alloys Processed by ECAE

2006 ◽  
Vol 503-504 ◽  
pp. 769-774 ◽  
Author(s):  
Shintaro Yoshimoto ◽  
Yuichi Miyahara ◽  
Z. Horita ◽  
Yoshihito Kawamura
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Yield Strength ◽  
High Strength ◽  
Mg Alloys ◽  
Tensile Yield Strength ◽  
Ordered Structure ◽  
Lpso Phase ◽  
Microstructure Refinement

Development of high strength I/M Mg alloys has been tried by ECAE processing. The mechanical properties and microstructure of ECAE-processed Mg97Zn1Y2 alloy with LPSO (long-periodic stacking ordered) structure were investigated. The tensile yield strength and elongation of as-cast Mg97Zn1Y2 were improved substantially by ECAE process. ECAE-processed with yield strength of 290 MPa and elongation of 22 % was obtained. The microstructure of ECAE-processed Mg97Zn1Y2 alloy consisted of refined α-Mg with the grain size around 6.5 μm and finely dispersed LPSO phase. Furthermore, the some texture was formed by ECAE process. The improved mechanical properties seem to be originated by the microstructure refinement and texture.

Effect of Long-Period Stacking Order Phase and α-Mg Phase on Strength and Ductility of Mg-Zn-Y Alloy

2012 ◽  
Vol 706-709 ◽  
pp. 1237-1242 ◽  
Author(s):  
Masafumi Noda ◽  
Yoshihito Kawamura
Keyword(s):  
Mechanical Properties ◽  
Yield Strength ◽  
High Temperatures ◽  
Mg Alloys ◽  
Tensile Yield Strength ◽  
Block Type ◽  
Lpso Phase ◽  
Long Period ◽  
Stacking Order ◽  
Type Phase

Mg alloys are lightweight structural alloys that normally have a good castability and machinability as well as an excellent specific strength and rigidity. However, the mechanical properties of Mg alloys are inferior to those of Al alloys, and their range of industrial applications is limited. Recently, Mg–Zn–Y alloy has been found to show a high tensile yield strength with a good elongation. The alloy has a long-period stacking order (LPSO) phase as the secondary phase in an α-Mg phase. In general, the tensile yield strengths of LPSO-type Mg alloy are known to be markedly enhanced by the formation of kink bands in the LPSO phase and by microstructural refinement of the α-Mg phase during plastic deformation. The separate roles of the LPSO phase and the α-Mg phase in relation to the mechanical properties of high-strength LPSO-type Mg alloy were investigated at ambient and high temperatures. For high strengths at ambient and high temperatures, it was important that the α-Mg phase consisted of a fine-grain region and a nonrecrystallized region, and that the LPSO phase remained as a block-type phase. On the other hands, it was necessary to change the LPSO phase from a block-type phase into a plate-type phase by heat treatment before tensile testing to improve the ductility of the alloy while maintaining its tensile yield strength. Microstructural control of the LPSO phase and the α-Mg phase is necessary to obtained Mg–Zn–Y alloy with superior mechanical properties at ambient-to-high temperatures.

Paradox of Strength and Ductility in Metals Processed Bysevere Plastic Deformation

2002 ◽  
Vol 17 (1) ◽  
pp. 5-8 ◽  
Author(s):  
R. Z. Valiev ◽  
I. V. Alexandrov ◽  
Y. T. Zhu ◽  
T. C. Lowe
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Grain Size ◽  
Yield Strength ◽  
Mechanical Behavior ◽  
High Strength ◽  
High Ductility ◽  
Elongation To Failure ◽  
Failure Ductility ◽  
Strength And Ductility

It is well known that plastic deformation induced by conventional forming methodssuch as rolling, drawing or extrusion can significantly increase the strength of metalsHowever, this increase is usually accompanied by a loss of ductility. For example, Fig.1 shows that with increasing plastic deformation, the yield strength of Cu and Almonotonically increases while their elongation to failure (ductility) decreases. Thesame trend is also true for other metals and alloys. Here we report an extraordinarycombination of high strength and high ductility produced in metals subject to severeplastic deformation (SPD). We believe that this unusual mechanical behavior is causedby the unique nanostructures generated by SPD processing. The combination ofultrafine grain size and high-density dislocations appears to enable deformation by newmechanisms. This work demonstrates the possibility of tailoring the microstructures ofmetals and alloys by SPD to obtain both high strength and high ductility. Materialswith such desirable mechanical properties are very attractive for advanced structuralapplications.

scholarly journals Effect of enhanced weld cooling on the mechanical properties of a structural steel with a yield strength of 700 MPa

2020 ◽  
Vol 2 (11) ◽  
Author(s):  
Juhani Laitila ◽  
Lassi Keränen ◽  
Jari Larkiola
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Fatigue Strength ◽  
Impact Toughness ◽  
Yield Strength ◽  
Uniform Elongation ◽  
High Strength ◽  
Low Alloy Steel ◽  
External Cooling ◽  
Welding Processes

AbstractIn this study, we present the effect of enhanced cooling on the mechanical properties of a high-strength low-alloy steel (having a yield strength of 700 MPa) following a single-pass weld process. The properties evaluated in this study include uniform elongation, impact toughness, yield, tensile and fatigue strengths alongside the cooling time of the weld. With the steel used in this study, the enhanced cooling resulted in a weld joint characterized with excellent cross-weld uniform elongation, yield and fatigue strength. The intensified cooling reduced the time it takes for the weld to reach 100 °C by around 190 s. Not only the fusion line of the weld was less pronounced, but also the grain size of the CGHAZ was greatly refined as a result of the enhanced cooling. The results indicate that combining external cooling to the welding processes can be beneficial for the studied high-strength steel.

scholarly journals Effect of Heat Treatment on Mechanical Properties and Microstructure Morphology of Low-Alloy High-Strength Steel

2016 ◽  
Vol 61 (2) ◽  
pp. 475-480
Author(s):  
K. Bolanowski
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Yield Strength ◽  
High Strength Steel ◽  
High Strength ◽  
Strengthening Phase ◽  
Average Grain Size

Abstract The paper analyzes the influence of different heat treatment processes on the mechanical properties of low-alloy high-strength steel denoted by Polish Standard (PN) as 10MnVNb6. One of the findings is that, after aging, the mechanical properties of rolled steel are high: the yield strength may reach > 600 MPa, and the ultimate tensile strength is > 700 MPa. These properties are largely dependent on the grain size and dispersion of the strengthening phase in the ferrite matrix. Aging applied after hot rolling contributes to a considerable rise in the yield strength and ultimate tensile strength. The process of normalization causes a decrease in the average grain size and coalescence (reduction of dispersion) of the strengthening phase. When 10MnVNb6 steel was aged after normalization, there was not a complete recovery in its strength properties.

scholarly journals Achieving High Yield Strength and Ductility in As-Extruded Mg-0.5Sr Alloy by High Mn–Alloying

Materials ◽  
2020 ◽  
Vol 13 (18) ◽  
pp. 4176
Author(s):  
Shibo Zhou ◽  
Xiongjiangchuan He ◽  
Peng Peng ◽  
Tingting Liu ◽  
Guangmin Sheng ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Yield Strength ◽  
Tensile Yield Strength ◽  
High Yield ◽  
Compressive Yield Strength ◽  
High Yield Strength ◽  
Pinning Effect ◽  
Small Grains ◽  
Strength And Ductility

The effect of Mn on the microstructure and mechanical properties of as-extruded Mg-0.5Sr alloy were discussed in this work. The results showed that high Mn alloying (2 wt.%) could significantly improve the mechanical properties of the alloys, namely, the tensile and compressive yield strength. The grain size of as-extruded Mg-0.5Sr alloys significantly was refined from 2.78 μm to 1.15 μm due to the pinning effect by fine α-Mn precipitates during the extrusion. Moreover, it also showed that the tensile yield strength and the compressive yield strength of Mg-0.5Sr-2Mn alloy were 32 and 40 percent age higher than those of Mg-0.5Sr alloy, respectively. Moreover, the strain hardening behaviors of the Mg-0.5Sr-2Mn alloy were discussed, which proved that a large number of small grains and texture have an important role in improving mechanical properties.

Effect of ZrB2 Nanoparticle Addition: Nano-LPSO-Grain Structured Ultra-High Strength Mg-RE Alloy

2014 ◽  
Vol 783-786 ◽  
pp. 425-430
Author(s):  
Muralidharan Paramsothy ◽  
Manoj Gupta
Keyword(s):  
Solid Solution ◽  
Grain Size ◽  
Yield Strength ◽  
Polycrystalline Material ◽  
High Strength ◽  
Tensile Yield Strength ◽  
Intermetallic Formation ◽  
Long Period ◽  
Ordered Phases ◽  
The Common

Currently, long period stacking/ordered phases (LPSO phases) are known to reinforceMg97Y2Zn1 type Mg-RE alloys. The LPSO phases are composed of a solid solution of Y and Znatoms placed orderly in long periods along the Mg basal plane. Also, an efficient way to strengthena polycrystalline material is to reduce its grain size. This increases the density of grain boundarieswhich impede the flow of dislocations. In many of the LPSO forming solidification processed Mg-RE alloys, the common practice is to solutionize the ingot, quench in warm water, hot extrude andthermally age. While this practice is suitable for obtaining high strength Mg-RE alloys, itconveniently employs the common idea in conventional metallurgy of fine intermetallicstrengthening while refining the grain size to within the micron regime. In this work, an alternativemethod involving boride nanoparticle addition to obtain a selected solidification processed ultrahighstrength (tensile yield strength > 400 MPa) Mg-RE alloy is discussed. Here, LPSO phaserather than fine intermetallic formation while retaining grain size under the micron regime ishighlighted.

scholarly journals Influence of Grain Size and Texture on the Yield Strength of Mg Alloys Processed by Severe Plastic Deformation

2014 ◽  
Vol 2014 ◽  
pp. 1-9 ◽  
Author(s):  
Jinbao Lin ◽  
Weijie Ren ◽  
Qudong Wang ◽  
Lifeng Ma ◽  
Yongjun Chen
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Grain Size ◽  
Yield Strength ◽  
Severe Plastic Deformation ◽  
Flow Behavior ◽  
Influence Factors ◽  
Mg Alloys ◽  
Processing Conditions ◽  
Strength And Ductility

Severe plastic deformation (SPD) has been widely employed to refine the grain size of Mg alloys, with the main objective to improve the strength and ductility of Mg alloys, since the well-known Hall-Petch equation suggests that a decreased grain size leads to an increased yield strength. However, the yield strength of Mg alloys processed by SPD is often decreased even though the grain size is effectively reduced. The abnormal flow behavior in Mg alloys processed by SPD has attracted great attention although this mechanism is still unclear, due to its complex and extensive influence factors. In this paper, the relationships between the processing conditions, grain refinement, and mechanical properties of the SPD treated Mg alloys are reviewed, with the emphasis on the effects of grain size and texture on the yield strength.

Microstructure Refinement of Magnesium Based Alloy

2005 ◽  
Vol 488-489 ◽  
pp. 143-146 ◽  
Author(s):  
Feng Xue ◽  
Wenwen Du ◽  
Yang Shan Sun
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Yield Strength ◽  
Surface Quality ◽  
Az31 Alloy ◽  
Pure Magnesium ◽  
Alloy Az31 ◽  
Microstructure Refinement ◽  
Order Of Magnitude ◽  
Hot Rolled

Additions of grain refiners based on Ca, Ca/Si, Al3Ti and Al4C3 to pure magnesium and AZ31 alloy result in remarkable microstructure refinement. With proper amount of these refiners addition, the grain size in as-cast ingots is one order of magnitude lower than that without refiner addition. Small amount of refiner addition to alloy AZ31 increases both ultimate and yield strength significantly, and the ductility of the alloy is similar to that without refiner addition. Additions of refiner improve the deformation formability of the AZ31 alloy.The extruded and hot rolled specimens (rods or sheets) with refiner addition are crack free and exhibit higher surface quality and mechanical properties than that without refiner addition.

BETHLEHEM LUKENS PLATE SPARTAN

Alloy Digest ◽  
2003 ◽  
Vol 52 (8) ◽  
Keyword(s):  
Fracture Toughness ◽  
Yield Strength ◽  
Tensile Properties ◽  
High Strength Steels ◽  
High Strength ◽  
Tensile Yield Strength ◽  
Precipitation Reactions

Abstract Bethlehem Lukens Plate (BLP) offers five grades of Spartan high-strength steels with tensile yield strength over 690 MPa (100 ksi). These alloys contain copper for precipitation reactions. They also have improved weldability and toughness compared to ASTM A 514 and A 543 grades. This datasheet provides information on composition, microstructure, hardness, and tensile properties as well as fracture toughness. It also includes information on forming and joining. Filing Code: SA-518. Producer or source: Bethlehem Lukens Plate.

scholarly journals Grain Size Evolution and Mechanical Properties of Nb, V–Nb, and Ti–Nb Boron Type S1100QL Steels

Metals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 492
Author(s):  
Jan Foder ◽  
Jaka Burja ◽  
Grega Klančnik
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Hot Forging ◽  
Size Control ◽  
High Strength ◽  
Fatigue Properties ◽  
Titanium Addition ◽  
Austenite Grain Size ◽  
Size Evolution

Titanium additions are often used for boron factor and primary austenite grain size control in boron high- and ultra-high-strength alloys. Due to the risk of formation of coarse TiN during solidification the addition of titanium is limited in respect to nitrogen. The risk of coarse nitrides working as non-metallic inclusions formed in the last solidification front can degrade fatigue properties and weldability of the final product. In the presented study three microalloying systems with minor additions were tested, two without any titanium addition, to evaluate grain size evolution and mechanical properties with pre-defined as-cast, hot forging, hot rolling, and off-line heat-treatment strategy to meet demands for S1100QL steel. Microstructure evolution from hot-forged to final martensitic microstructure was observed, continuous cooling transformation diagrams of non-deformed austenite were constructed for off-line heat treatment, and the mechanical properties of Nb and V–Nb were compared to Ti–Nb microalloying system with a limited titanium addition. Using the parameters in the laboratory environment all three micro-alloying systems can provide needed mechanical properties, especially the Ti–Nb system can be successfully replaced with V–Nb having the highest response in tensile properties and still obtaining satisfying toughness of 27 J at –40 °C using Charpy V-notch samples.

Sign in / Sign up

Export Citation Format

Share Document