Influence of Silver / CNTs on Epoxide Resin Based Conductive Adhesive

2009 ◽  
Vol 610-613 ◽  
pp. 299-303
Author(s):  
Shu Quan Liang ◽  
Yan Tang ◽  
Yong Zhang ◽  
Zhong Jie ◽  
Xiao Pin Tan
Keyword(s):  
Tensile Strength ◽  
Ultrasonic Method ◽  
Silver Powder ◽  
Tensile Modulus ◽  
Conductive Adhesive ◽  
Resin Matrix ◽  
Epoxide Resin ◽  
Weight Percentage ◽  
Dispersion State ◽  
Milling Method

Silver / CNTs was prepared by ball milling method and was used as filler to reinforce epoxide resin based conductive adhesive. The effect of content and dispersion state of the filler on tensile strength, tensile modulus, fracture extensibility and electrical resistance of the composites were studied. The results indicated that the filler could be dispersed well in epoxide resin matrix by ultrasonic method and the mechanical and electrical properties was improved greatly. The best content of the silver / CNTs was 0.75 wt% (considering of CNTs weight percentage), when the tensile strength, tensile modulus and fracture extensibility increased 42.6%, 18.8% and 115.3% respectively. With the increase of silver/CNTs, the conductivity of the matrix increased significantly. The micro structure analyses showed that the silver-covered CNTs worked as conductive channel and the electrons were easy to transfer through silver powder by CNTs network.

Effects of Seawater Immersion on Mechanical Properties of CFRP Composites

2013 ◽  
Vol 785-786 ◽  
pp. 209-213
Author(s):  
Qi Zhong Huang ◽  
Zhao Hui Hu
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Carbon Fiber ◽  
Water Absorption ◽  
Flexural Modulus ◽  
Tensile Modulus ◽  
Resin Matrix ◽  
Matrix Composites ◽  
Matrix Interface ◽  
Fiber Matrix Interface

Water absorption behavior and mechanical properties variation of the carbon fiber reinforced epoxy matrix composites (CFRP) immersed into artificial seawater were investigated by experiments. The rate of water absorption of the composite specimens is gradually reducing as the duality of immersion increasing. Due to the reversible and irreversible changes in the resin matrix and the failure of the fiber/matrix interface, the tensile strength, the flexural strength, and the ILSS of the composite specimens after 70 days immersion decreased 9.3%, 13%, and 17% respectively. And the tensile modulus and the flexural modulus the specimens after desorption were 83% and 70% of the original state, respectively

Morphology of High-Performance Rigid-Rod Polymer Fibers and Molecular Composites

1989 ◽  
Vol 47 ◽  
pp. 338-339
Author(s):  
W.W. Adams ◽  
S. J. Krause
Keyword(s):  
Tensile Strength ◽  
High Performance ◽  
Liquid Crystalline ◽  
Molecular Level ◽  
Synergistic Effects ◽  
Tensile Modulus ◽  
Commercial Development ◽  
The Matrix ◽  
Molecular Composites ◽  
Rigid Rod

Rigid-rod polymers such as PBO, poly(paraphenylene benzobisoxazole), Figure 1a, are now in commercial development for use as high-performance fibers and for reinforcement at the molecular level in molecular composites. Spinning of liquid crystalline polyphosphoric acid solutions of PBO, followed by washing, drying, and tension heat treatment produces fibers which have the following properties: density of 1.59 g/cm3; tensile strength of 820 kpsi; tensile modulus of 52 Mpsi; compressive strength of 50 kpsi; they are electrically insulating; they do not absorb moisture; and they are insensitive to radiation, including ultraviolet. Since the chain modulus of PBO is estimated to be 730 GPa, the high stiffness also affords the opportunity to reinforce a flexible coil polymer at the molecular level, in analogy to a chopped fiber reinforced composite. The objectives of the molecular composite concept are to eliminate the thermal expansion coefficient mismatch between the fiber and the matrix, as occurs in conventional composites, to eliminate the interface between the fiber and the matrix, and, hopefully, to obtain synergistic effects from the exceptional stiffness of the rigid-rod molecule. These expectations have been confirmed in the case of blending rigid-rod PBZT, poly(paraphenylene benzobisthiazole), Figure 1b, with stiff-chain ABPBI, poly 2,5(6) benzimidazole, Fig. 1c A film with 30% PBZT/70% ABPBI had tensile strength 190 kpsi and tensile modulus of 13 Mpsi when solution spun from a 3% methane sulfonic acid solution into a film. The modulus, as predicted by rule of mixtures, for a film with this composition and with planar isotropic orientation, should be 16 Mpsi. The experimental value is 80% of the theoretical value indicating that the concept of a molecular composite is valid.

Mechanical Property Improvement of Poly(Butylene Succinate) by Reinforcing with Modified Fumed Silica

2014 ◽  
Vol 1025-1026 ◽  
pp. 215-220 ◽  
Author(s):  
Sasirada Weerasunthorn ◽  
Pranut Potiyaraj
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Flexural Strength ◽  
Fumed Silica ◽  
Tensile Modulus ◽  
Silica Particles ◽  
Melt Mixing ◽  
Butylene Succinate ◽  
Ir Spectrophotometry

Fumed silica particles (SiO2) were directly added into poly (butylene succinate) (PBS) by melt mixing process. The effects of amount of fumed silica particles on mechanical properties of PBS/fumed silica composites, those are tensile strength, tensile modulus, impact strength as well as flexural strength, were investigated. It was found that the mechanical properties decreased with increasing fumed silica loading (0-3 wt%). In order to increase polymer-filler interaction, fumed silica was treated with 3-glycidyloxypropyl trimethoxysilane (GPMS), and its structure was analyzed by FT-IR spectrophotometry. The PBS/modified was found to possess better tensile strength, tensile modulus, impact strength and flexural strength that those of PBS/fumed silica composites.

Effect of Polyethylene Glycol in Nanocellulose/PLA Composites

2019 ◽  
Vol 821 ◽  
pp. 89-95
Author(s):  
Wanasorn Somphol ◽  
Thipjak Na Lampang ◽  
Paweena Prapainainar ◽  
Pongdhorn Sae-Oui ◽  
Surapich Loykulnant ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Lactic Acid ◽  
Polyethylene Glycol ◽  
Aspect Ratio ◽  
Mechanical Performance ◽  
Tensile Modulus ◽  
Poly Lactic Acid ◽  
Solvent Casting ◽  
Casting Method ◽  
Mediated Oxidation

Poly (lactic acid) or PLA was reinforced by nanocellulose and polyethylene glycol (PEG), which were introduced into PLA matrix from 0 to 3 wt.% to enhance compatibility and strength of the PLA. The nanocellulose was prepared by TEMPO-mediated oxidation from microcrystalline cellulose (MCC) powder and characterized by TEM, AFM, and XRD to reveal rod-like shaped nanocellulose with nanosized dimensions, high aspect ratio and high crystallinity. Films of nanocellulose/PEG/PLA nanocomposites were prepared by solvent casting method to evaluate the mechanical performance. It was found that the addition of PEG in nanocellulose-containing PLA films resulted in an increase in tensile modulus with only 1 wt% of PEG, where higher PEG concentrations negatively impacted the tensile strength. Furthermore, the tensile strength and modulus of nanocellulose/PEG/PLA nanocomposites were higher than the PLA/PEG composites due to the existence of nanocellulose chains. Visual traces of crazing were detailed to describe the deformation mechanism.

scholarly journals Enhanced Tensile Strength of Monolithic Epoxy with Highly Dispersed TiO2-Graphene Nanocomposites

2021 ◽  
Vol 5 (7) ◽  
pp. 191
Author(s):  
Yanshuai Wang ◽  
Siyao Guo ◽  
Biqin Dong ◽  
Feng Xing
Keyword(s):  
Tensile Strength ◽  
Epoxy Resin ◽  
Mechanical Performance ◽  
Chemical Properties ◽  
High Mechanical Property ◽  
Graphene Nanocomposites ◽  
Highly Dispersed ◽  
Dispersion State ◽  
Physical And Chemical

The functionalization of graphene has been reported widely, showing special physical and chemical properties. However, due to the lack of surface functional groups, the poor dispersibility of graphene in solvents strongly limits its engineering applications. This paper develops a novel green “in-situ titania intercalation” method to prepare a highly dispersed graphene, which is enabled by the generation of the titania precursor between the layer of graphene at room temperature to yield titania-graphene nanocomposites (TiO2-RGO). The precursor of titania will produce amounts of nano titania between the graphene interlayers, which can effectively resist the interfacial van der Waals force of the interlamination in graphene for improved dispersion state. Such highly dispersed TiO2-RGO nanocomposites were used to modify epoxy resin. Surprisingly, significant enhancement of the mechanical performance of epoxy resin was observed when incorporating the titania-graphene nanocomposites, especially the improvements in tensile strength and elongation at break, with 75.54% and 176.61% increases at optimal usage compared to the pure epoxy, respectively. The approach presented herein is easy and economical for industry production, which can be potentially applied to the research of high mechanical property graphene/epoxy composite system.

Mechanical properties of low-density paper

2020 ◽  
Vol 35 (1) ◽  
pp. 61-70
Author(s):  
Na Young Park ◽  
Young Chan Ko ◽  
Lili Melani ◽  
Hyoung Jin Kim
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Structural Change ◽  
Tensile Testing ◽  
Tensile Modulus ◽  
Gauge Length ◽  
Efficiency Factor ◽  
Low Density ◽  
Tensile Stiffness ◽  
Lower Tensile Strength

AbstractFor the mechanical properties of paper, tensile testing has been widely used. Among the tensile properties, the tensile stiffness has been used to determine the softness of low-density paper. The lower tensile stiffness, the greater softness of paper. Because the elastic region may not be clearly defined in a load-elongation curve, it is suggested to use the tensile modulus which is defined as the slope between the two points in the curve. The two points which provide the best correlation with subjective softness evaluation should be selected. Low-density paper has a much lower tensile strength, but much larger elongation at the break. It undergoes a continuous structural change during mechanical testing. The degree of the structural change should depend on tensile conditions such as the sample size, the gauge length, and the rate of elongation. For low-density paper, the tensile modulus and the tensile strength should be independent of each other. The structure efficiency factor (SEF) is defined as a ratio of the tensile strength to the tensile modulus and it may be used a guideline in developing superior low-density paper products.

Tensile Properties of Polypropylene/Cocoa Pod Husk Biocomposites: Effect of Maleated Polypropylene

2013 ◽  
Vol 747 ◽  
pp. 645-648 ◽  
Author(s):  
Koay Seong Chun ◽  
Salmah Husseinsyah ◽  
Hakimah Osman
Keyword(s):  
Tensile Strength ◽  
Tensile Properties ◽  
Tensile Modulus ◽  
Melt Blending ◽  
Elongation At Break ◽  
Maleated Polypropylene ◽  
Matrix Interaction ◽  
Cocoa Pod Husk ◽  
Blending Process ◽  
Scanning Electron

Polypropylene/Cocoa Pod Husk (PP/CPH) biocomposites with different maleated polypropylene (MAPP) content were prepared via melt blending process using Brabender Plastrograph mixer. The tensile strength and tensile modulus of PP/CPH biocomposites increased with increasing of MAPP content. The PP/CPH biocomposites with 5 phr of MAPP showed the optimum improvement on tensile properties. However, the increased of MAPP content reduced the elongation at break of PP/CPH biocomposites. At 5 phr of MAPP content, PP/CPH biocomposites showed lowest elongation at break. Scanning electron microscope confirms the PP/CPH biocomposites with MAPP have better filler-matrix interaction and adhesion due to the effect of MAPP.

scholarly journals Mechanical Properties of Oil Palm Shell Composites

2016 ◽  
Vol 2016 ◽  
pp. 1-7 ◽  
Author(s):  
J. Sahari ◽  
M. A. Maleque
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Oil Palm ◽  
Volume Fraction ◽  
Unsaturated Polyester ◽  
Tensile Modulus ◽  
Sem Analysis ◽  
Palm Shell ◽  
Pull Out ◽  
Oil Palm Shell

The mechanical properties of oil palm shell (OPS) composites were investigated with different volume fraction of OPS such as 0%, 10%, 20%, and 30% using unsaturated polyester (UPE) as a matrix. The results presented that the tensile strength and tensile modulus of the UPE/OPS composites increased as the OPS loading increased. The highest tensile modulus of UPE/OPS was obtained at 30 vol% of OPS with the value of 8.50 GPa. The tensile strength of the composites was 1.15, 1.17, and 1.18 times higher than the pure UPE matrix for 10, 20, and 30 vol% of OPS, respectively. The FTIR spectra showed the change of functional group of composites with different volume fractions of OPS. SEM analysis shows the filler pull-out present in the composites which proved the poor filler-matrix interfacial bonding.

Durability study of ramie fiber fabric reinforced phenolic plates under humidity conditions

2016 ◽  
Vol 23 (1) ◽  
pp. 45-52 ◽  
Author(s):  
Guijun Xian ◽  
Peng Yin ◽  
Innocent Kafodya ◽  
Hui Li ◽  
Wei-lun Wang
Keyword(s):  
Relative Humidity ◽  
Moisture Content ◽  
Tensile Modulus ◽  
Resin Matrix ◽  
Ramie Fiber ◽  
Short Beam ◽  
Low Degree ◽  
Beam Shear ◽  
Ramie Fibers ◽  
Fiber Fabric

AbstractA durability study of a ramie fiber fabric reinforced phenolic resin (RFRP) plate under 50%, 85%, and 98% relative humidity for 6 months at room temperature was performed. Water absorption and desorption, tensile and short beam shear strengths of the RFRP plates were investigated as a function of exposure time. RFRP samples show strong hydrophilic characteristics and the saturated water content varies from 0.73% to 4.5% with relative humidity ranging from 50% to 98%. After 6 months of exposure to 98% relative humidity, an abnormal extra amount of moisture was absorbed, which may have resulted from cracks in the resin matrix or from debonding between fiber and resin due to swelling of the fibers with high moisture content. It was found that the tensile modulus is more susceptible to moisture uptake, which is ascribed to the degradation of ramie fibers with the water ingress. An approximate linearity between the mechanical properties and the moisture content is observed if the abnormal extra water uptake is neglected. Both tensile and short beam shear strengths of the RFRP samples recovered remarkably when samples were fully dried at 60°C, indicating a low degree of permanent degradation occurred due to the exposure.

scholarly journals Modified rule of mixtures and Halpin–Tsai model for prediction of tensile strength of micron-sized reinforced composites and Young’s modulus of multiscale reinforced composites for direct extrusion fabrication

2018 ◽  
Vol 10 (7) ◽  
pp. 168781401878528 ◽  
Author(s):  
Zirong Luo ◽  
Xin Li ◽  
Jianzhong Shang ◽  
Hong Zhu ◽  
Delei Fang
Keyword(s):  
Carbon Nanotubes ◽  
Tensile Strength ◽  
Young’S Modulus ◽  
Carbon Fibers ◽  
Epoxy Resins ◽  
Young's Modulus ◽  
Resin Matrix ◽  
Reinforced Composites ◽  
Rule Of Mixtures ◽  
Combined Use

A modified rule of mixtures is required to account for the experimentally observed nonlinear variation of tensile strength. A modified Halpin–Tsai model was presented to predict the Young’s modulus of multiscale reinforced composites with both micron-sized and nano-sized reinforcements. In the composites, both micron-sized fillers—carbon fibers—and nano-sized fillers—rubber nanoparticles and carbon nanotubes—are added into the epoxy resin matrix. Carbon fibers can help epoxy resins increase both the tensile strength and Young’s modulus, while rubber nanoparticles and carbon nanotubes can improve the toughness without sacrificing other properties. Mechanical experiments and scanning electron microscopy observations were used to study the effects of the micron-sized and nano-sized reinforcements and their combination on tensile and toughness properties of the composites. The results showed that the combined use of multiscale reinforcements had synergetic effects on both the strength and the toughness of the composites.

Sign in / Sign up

Export Citation Format

Share Document