Influence of Annealing on the Microstructure and Mechanical Properties of Electrodeposited Nanocrystalline Nickel

2011 ◽  
Vol 683 ◽  
pp. 103-112 ◽  
Author(s):  
B. Yang
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Elastic Modulus ◽  
Grain Boundary ◽  
Boundary Structure ◽  
Boundary State ◽  
Microstructure And Mechanical Properties ◽  
Grain Boundary Structure ◽  
Average Grain Size ◽  
Different Grain Size

The evolution of the microstructure and mechanical properties of electrodeposited nanocrystalline Ni with different annealing procedures was studied systematically. For the annealed specimens hardness decreases with increasing average grain size but the dependence changes at different grain size ranges. The specimens annealed at a low temperature show higher hardness compared to the as-deposited nanocrystalline Ni, despite an increased measured average grain size. In association with this hardening an increase in elastic modulus and a decrease in microstrain was observed after annealing. With increasing annealing temperature both the tensile strength and the fracture strain were observed to decrease, this is companied with a transition from ductile to brittle in the fracture surfaces. These results indicated that the mechanical behaviour of nanocrystalline Ni depends not only on the average grain size but also on the grain boundary structure. A change in the grain boundary state arising from annealing may be responsible for the observed increase in hardness and elastic modulus as well as the deterioration of tensile properties.

Crystal Stability and Microstructural Evolution in Polycrystalline Si Films During Ion Irradiation

1989 ◽  
Vol 147 ◽  
Author(s):  
Harry A. Atwater ◽  
Walter L. Brown
Keyword(s):  
Grain Size ◽  
Grain Boundary ◽  
Grain Boundaries ◽  
Ion Irradiation ◽  
Marked Change ◽  
Boundary Structure ◽  
Nucleation Kinetics ◽  
Grain Boundary Structure ◽  
Average Grain Size ◽  
Amorphous Si

AbstractAmorphous Si is nucleated heterogeneously at grain boundaries during irradiation of polycrystalline Si by 1.5 MeV Xe+ ions for temperatures of 150–225°C. Following formation at grain boundaries, the amorphous Si layer grows at a rate comparable to the growth rate of a pre-existing amorphous-crystal interface, resulting in a decrease in average grain size and a marked change in the grain size distribution. The heterogeneous nucleation kinetics of amorphous Si are strongly dependent on grain boundary structure. A simple atomistic model for amorphous phase formation, which suggests that the nucleation kinetics are dependent on the point defect mobilities and grain boundary structure, is related to the experimental results.

Effect of CoO Doping on the Sintering Ability and Mechanical Properties of Y-TZP

2004 ◽  
Vol 449-452 ◽  
pp. 265-268 ◽  
Author(s):  
Tetsuhiko Onda ◽  
H. Yamauchi ◽  
Motozo Hayakawa
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Grain Boundary ◽  
Grain Refinement ◽  
Grain Growth ◽  
Sintering Temperature ◽  
Tetragonal Zirconia ◽  
Boundary Structure ◽  
Grain Boundary Structure ◽  
Boundary Strength

The effect of CoO addition into Y-TZP (Yttria doped Tetragonal Zirconia Polycrystals) was studied on the evolution of its sintering ability, grain size, grain boundary structure and mechanical properties. The doping of a small amount of CoO effectively reduced the sintering temperature. A small amount of CoO up to ~ 0.3 mol% was effective for the suppression of grain growth, but the addition of 1.0 mole % resulted in an enhanced grain growth. The hardness and toughness of the CoO doped TZP were about the same as those of undoped TZP. Furthermore, despite the grain refinement, CoO doped TZP did not exhibit improved mechanical properties. This may be suggesting that CoO dopant had weakened the grain boundary strength.

Microstructure and Mechanical Properties of TiB2/Al-Si Composites Fabricated by Electron Beam Rapid Manufacture

2021 ◽  
Vol 1035 ◽  
pp. 884-891
Author(s):  
Qing Feng Yang ◽  
Cun Juan Xia ◽  
Xian Feng Li ◽  
Hao Wei Wang ◽  
Nan Liao
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Electron Beam ◽  
Grain Boundary ◽  
Microstructure And Mechanical Properties ◽  
Average Grain Size ◽  
Before And After ◽  
Rapid Manufacture ◽  
Equiaxed Grains

Bulky sample was fabricated by electron beam rapid manufacture (EBRM) technology, in which Ф1.6 mm wire of in-situ TiB2/Al-Si compositeswas selected as deposition metal, following byT6 heat treatment. The microstructure and mechanical properties of the bulky sample before and afterheat treatment were analyzed. Experimental results showed that the microstructure parallel to the weld was similar to that perpendicular to the weld. The microstructure of the as-deposited sample consisted of columnar and equiaxed grains, in which siliconwas distributed along the grain boundary and the grain size was about 30 μm. Besides, some TiB2 particles converged at the grain boundary. After T6 heat treatment, the average grain size of the sample increasedobviously.The average hardness of the sample was increased to 114.65 HV from 46.55 HV, an increase of 146%. The tensile strength of the sample increased to 326.66MPafrom 143.97 MPa, but the elongationdecreased compared with that of the as-deposited state. The tensile test showed that the mechanical properties of TiB2/Al-Si composites formed by electron beam rapid manufacture were isotropic before and after heat treatment.

Mechanical properties of nanocrystalline and epitaxial TiN films on (100) silicon

2001 ◽  
Vol 16 (9) ◽  
pp. 2733-2738 ◽  
Author(s):  
H. Wang ◽  
A. Sharma ◽  
A. Kvit ◽  
Q. Wei ◽  
X. Zhang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Grain Boundary ◽  
Single Crystal ◽  
Grain Boundary Sliding ◽  
Boundary Structure ◽  
Triple Junctions ◽  
Tin Films ◽  
Grain Boundary Structure ◽  
Transmission Electron

We investigated mechanical properties of TiN as a function of microstructure varying from nanocrystalline to single crystal TiN films deposited on (100) silicon substrates. By varying the substrate temperature from 25 to 700 °C during pulsed laser deposition, the microstructure of TiN films changed from nanocrystalline (having a uniform grain size of 8 nm) to a single crystal epitaxial film on the silicon (100) substrate. The microstructure and epitaxial nature of these films were investigated using x-ray diffraction and high-resolution transmission electron microscopy. Hardness measurements were made using nanoindentation techniques. The nanocrystalline TiN contained numerous triple junctions without any presence of amorphous regions. The width of the grain boundary remained constant at less than 1 nm as a function of boundary angle. Similarly the grain boundary structure did not change with grain size. The hardness of TiN films decreased with decreasing grain size. This behavior was modeled recently involving grain boundary sliding, which is particularly relevant in the case of hard materials such as TiN.

On the Role of Grain-Boundary Films in Optimizing the Mechanical Properties of Silicon Carbide Ceramics

2004 ◽  
Vol 818 ◽  
Author(s):  
R. O. Ritchie ◽  
X.-F. Zhang ◽  
L. C. De Jonghe
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Fracture Toughness ◽  
Silicon Carbide ◽  
Grain Boundary ◽  
Elevated Temperatures ◽  
Boundary Structure ◽  
Intergranular Films ◽  
Grain Boundary Structure ◽  
Silicon Carbide Ceramics

AbstractThrough control of the grain-boundary structure, principally in the nature of the nanoscale intergranular films, a silicon carbide with a fracture toughness as high as 9.1 MPa.m1/2 has been developed by hot pressing β-SiC powder with aluminum, boron, and carbon additions (ABC-SiC). Central in this material development has been systematic transmission electron microscopy (TEM) and mechanical characterizations. In particular, atomic-resolution electron microscopy and nanoprobe composition quantification were combined in analyzing grain boundary structure and nanoscale structural features. Elongated SiC grains with 1 nm-wide amorphous intergranular films were believed to be responsible for the in situ toughening of this material, specifically by mechanisms of crack deflection and grain bridging. Two methods were found to be effective in modifying microstructure and optimizing mechanical performance. First, prescribed post-annealing treatments at temperatures between 1100 and 1500°C were seen to cause full crystallization of the amorphous intergranular films and to introduce uniformly dispersed nanoprecipitates within SiC matrix grains; in addition, lattice diffusion of aluminum at elevated temperatures was seen to alter grain-boundary composition. Second, adjusting the nominal content of sintering additives was also observed to change the grain morphology, the grain-boundary structure, and the phase composition of the ABC-SiC. In this regard, the roles of individual additives in developing boundary microstructures were identified; this was demonstrated to be critical in optimizing the mechanical properties, including fracture toughness and fatigue resistance at ambient and elevated temperatures, flexural strength, wear resistance, and creep resistance.

Mechanism of Surface Dissolution in Dense Hydroxyapatite

2007 ◽  
Vol 121-123 ◽  
pp. 1241-1244 ◽  
Author(s):  
Dong Seok Seo ◽  
Hwan Kim ◽  
Jong Kook Lee
Keyword(s):  
Mechanical Properties ◽  
Grain Boundary ◽  
Grain Boundaries ◽  
Xrd Analysis ◽  
Boundary Structure ◽  
Molar Ratio ◽  
Dissolution Mechanism ◽  
Grain Boundary Structure ◽  
High Resolution Tem ◽  
Moisture Protection

In this study, it was demonstrated how second phases with small amount, which are hardly detected by XRD analysis, affect grain boundary dissolution and related mechanical properties of HA. All HA disks sintered at 1200 oC for 2 h in air with under moisture protection were phase pure and had Ca/P molar ratio of 1.67. Following certain period of exposure to the distilled water, the surface dissolution initiated at grain boundaries and particle loosening, subsequently resulting in decrease in mechanical properties of HA. In order to understand the dissolution mechanism, grain boundary structure of HA was identified by transmission electron microscopy (TEM) and high resolution TEM observation. From the analysis, it was found that the non-stoichiometric phase as α-tricalcium phosphate (TCP) transformed from β-TCP was existed at grain boundaries and caused surface dissolution of HA. From the XRD analysis, it was found that (211) and (112) planes of hydroxyapatite were susceptible to dissolution, whereas (300) plane was relatively stable.

Effect of Bi on Microstructure and Mechanical Properties of Extruded AZ80-2Sn Magnesium Alloy

2018 ◽  
Vol 37 (1) ◽  
pp. 97-103 ◽  
Author(s):  
Hansong Xue ◽  
Xinyu Li ◽  
Weina Zhang ◽  
Zhihui Xing ◽  
Jinsong Rao ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Magnesium Alloy ◽  
Ultimate Tensile Strength ◽  
Yield Strength ◽  
Microstructure And Mechanical Properties ◽  
Average Grain Size

AbstractThe effects of Bi on the microstructure and mechanical properties of AZ80-2Sn alloy were investigated. The results show that the addition of Bi within the as-cast AZ80-2Sn alloy promotes the formation of Mg3Bi2 phase, which can refine the grains and make the eutectic phases discontinuous. The addition of 0.5 % Bi within the as-extruded AZ80-2Sn alloy, the average grain size decreases to 12 μm and the fine granular Mg17Al12 and Mg3Bi2 phases are dispersed in the α-Mg matrix. With an increase in Bi content, the Mg17Al12 and Mg3Bi2 phases become coarsened and the grain size increases. The as-extruded AZ80-2Sn-0.5 %Bi alloy has the optimal properties, and the ultimate tensile strength, yield strength and elongation are 379.6 MPa, 247.1 MPa and 14.8 %, respectively.

Investigation of Microstructure and Mechanical Properties of Friction Stir Lap Jointed Ni Base Superalloy

2012 ◽  
Vol 724 ◽  
pp. 481-485
Author(s):  
Kuk Hyun Song ◽  
Kazuhiro Nakata
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Friction Stir Welding ◽  
Base Material ◽  
Lap Joints ◽  
Stir Zone ◽  
Inconel 600 ◽  
Friction Stir ◽  
Microstructure And Mechanical Properties ◽  
Average Grain Size

This study evaluated the microstructure and mechanical properties of friction stir welded lap joints. Inconel 600 and SS 400 as experimental materials were selected, and friction stir welding was carried out at tool rotation speed of 200 rpm and welding speed of 100 mm/min. Applying the friction stir welding was notably effective to reduce the grain size of the stir zone, as a result, the average grain size of Inconel 600 was reduced from 20 μm in the base material to 8.5 μm in the stir zone. Joint interface between Inconel 600 and SS 400 showed a sound weld without voids and cracks. Also, the hook, along the Inconel 600 alloy from SS 400, was formed at advancing side, which directly affected an increase in peel strength. In this study, we systematically discussed the evolution on microstructure and mechanical properties of friction stir lap jointed Inconel 600 and SS 400.

Effects of Annealing Temperature on the Microstructure and Mechanical Properties of Electrodeposited Ni-Fe Alloy Foils

2017 ◽  
Vol 36 (3) ◽  
pp. 223-232 ◽  
Author(s):  
H. R. Ren ◽  
L. Guo ◽  
Z. C. Guo
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Grain Size ◽  
Elastic Modulus ◽  
Annealing Temperature ◽  
Experimental Results ◽  
Structure Defects ◽  
Alloy Foil ◽  
Heat Treated ◽  
Average Grain Size

AbstractThe plasticity, elastic modulus and thermal stability restrict the applications of electrodeposited nanocrystalline Ni-Fe alloy foils. To improve its mechanical properties, the electrodeposited Ni-Fe alloy foils were heat treated within the temperature 900–1,150 °C. The microstructure and texture of the samples were further analyzed with a combination of SEM, XRD and EBSD. The experimental results indicated that the electrodeposited Ni-Fe alloy foil had poor mechanical properties at about 1,000 °C, which was mainly attributed to the development of a mixed grain microstructure. At 900–950 °C, the plastic and elastic modulus were greatly improved, which were owed to the uniformed microstructure and the decrease of structure defects. At 1,050–1,150 °C, the degree of the mixed grain microstructure decreased, resulting in improved plasticity and higher elastic modulus. However, the strength of the foil obviously decreased, which was mainly associated with the increase of the average grain size.

Sign in / Sign up

Export Citation Format

Share Document