Chacterization of Tensile Strength Dependence with Diameter of Sponge Gourd Fibers by Weibull Statistical Analysis

2014 ◽  
Vol 775-776 ◽  
pp. 86-91 ◽  
Author(s):  
Verônica Scarpini Candido ◽  
Michel Picanço Oliveira ◽  
Raissa de Almeida Gouvêa ◽  
Amanda Luiza Bezerra S. Martins ◽  
Sérgio Neves Monteiro
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Natural Fibers ◽  
Inverse Correlation ◽  
Lignocellulosic Fibers ◽  
Weibull Statistical Analysis ◽  
Sponge Gourd ◽  
Strength Dependence ◽  
Important Possibility ◽  
Different Diameters

Lignocellulosic fibers with relatively unknowns mechanical properties such as those extracted from the sponge gourd, are being investigated as polymer composites reinforcement. The use of natural fibers are related to environmental , technical, economical and social advantages. An important possibility of improving the mechanical properties is the fact that lignocellulosic fibers may present tensile strength inversely correlated with their diameter. Therefore, this possibility was investigated in the present work regarding sponge gourd fibers by means of the Weibull statistic analysis. The results supported a hyperbolic inverse correlation between the strength of sponge gourd fibers with their diameter. Scanning electron microscopy observation of fibers with different diameters revealed possible mechanisms for the strength inverse correlation with diameter.

scholarly journals The Structure and Mechanical Properties of Hemp Fibers-Reinforced Poly(ε-Caprolactone) Composites Modified by Electron Beam Irradiation

2021 ◽  
Vol 11 (12) ◽  
pp. 5317
Author(s):  
Rafał Malinowski ◽  
Aneta Raszkowska-Kaczor ◽  
Krzysztof Moraczewski ◽  
Wojciech Głuszewski ◽  
Volodymyr Krasinskyi ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Electron Beam ◽  
Impact Strength ◽  
Flexural Modulus ◽  
Natural Fibers ◽  
High Energy ◽  
Electron Radiation ◽  
Elongation At Break ◽  
Hemp Fibers

The need for the development of new biodegradable materials and modification of the properties the current ones possess has essentially increased in recent years. The aim of this study was the comparison of changes occurring in poly(ε-caprolactone) (PCL) due to its modification by high-energy electron beam derived from a linear electron accelerator, as well as the addition of natural fibers in the form of cut hemp fibers. Changes to the fibers structure in the obtained composites and the geometrical surface structure of sample fractures with the use of scanning electron microscopy were investigated. Moreover, the mechanical properties were examined, including tensile strength, elongation at break, flexural modulus and impact strength of the modified PCL. It was found that PCL, modified with hemp fibers and/or electron radiation, exhibited enhanced flexural modulus but the elongation at break and impact strength decreased. Depending on the electron radiation dose and the hemp fibers content, tensile strength decreased or increased. It was also found that hemp fibers caused greater changes to the mechanical properties of PCL than electron radiation. The prepared composites exhibited uniform distribution of the dispersed phase in the polymer matrix and adequate adhesion at the interface between the two components.

scholarly journals Manufacture and Mechanical Behavior of Green Polymeric Composite Reinforced with Hydrated Cotton Fiber

2019 ◽  
Vol 2 (1) ◽  
Author(s):  
Ênio Henrique Pires da Silva ◽  
Emiliano Barretto Almendro ◽  
Amanda Albertin Xavier da Silva ◽  
Guilherme Waldow ◽  
Flaminio CP Sales ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Cotton Fiber ◽  
Natural Fibers ◽  
Young Modulus ◽  
Polymeric Composite ◽  
Morphological Characterization ◽  
Comparison And Study ◽  
Fiber Fabric

Composites using natural fibers as reinforcement and biodegradable polymers as matrix are considered environmentally friendly materials. This paper seeks the mechanical and morphological characterization of a biocomposite of polyurethane (PU) derived from a blend of vegetable oils doped with aluminatrihydrate (ATH) and reinforced with hydrated cotton fiber fabric (HCF). The comparison and study were performed based on the properties of the: (i) pure PU; (ii) PU doped with ATH containing 30% of the final mass (PU+30%ATH); (iii) composite of PU reinforced with 7 layers of cotton fiber fabric (PU+7CF); (iv) composite of PU+30%ATH reinforced with 7 layers of CF (PU+30%ATH+7CF); (v) composite of PU+30%ATH reinforced with 7 layers of hydrated cotton fiber fabric (PU+30%ATH+7HCF). The mechanical properties obtained according to the tensile test for the composite PU+30%ATH+CF with fibers oriented at 0° showed a significant increment in tensile strength (60 MPa) and the modulus of elasticity (4.7 GPa) when compared to pure PU (40 MPa) and (1.7 GPa) respectively. PU+30%ATH also presented a rising tensile strength (31 MPa) and Young modulus (2.6 GPa). For the composite with addition of water, results presented a significant decrease in strength (31.3 MPa) and stiffness (0.9 GPa) than the composite with no water. Electron microscopy (SEM) analyses exhibited that the samples with addition of water showed the presence of large amounts of pores and the lower interaction between matrix and fiber. These results may explain the lower mechanical properties of this material. DOI: http://dx.doi.org/10.30609/JETI.2019-7576

Surface Modification of Banana Fiber and its Influence on Performance of Biodegradable Banana-Cassava Starch Composites

2019 ◽  
Vol 895 ◽  
pp. 15-20
Author(s):  
Raghavendra Subramanya ◽  
S.S. Prabhakara
Keyword(s):  
Mechanical Properties ◽  
Surface Modification ◽  
Alkali Treatment ◽  
Natural Fibers ◽  
Cassava Starch ◽  
Banana Fiber ◽  
Synthetic Fibers ◽  
Lignocellulosic Fibers ◽  
Biodegradable Composites ◽  
Banana Fibre

Natural fibers, in particularly lignocellulosic fibers are attracting material scientists now days, due to their comparative advantages over synthetic fibers. Biodegradable composites reinforced with short banana fibre after alkali treatment along with cassava starch matrix were prepared using the hot compression method. The mechanical properties like tensile strength and impact strength were investigated. Mechanical properties of the composites made from alkali treated fibres were superior to the untreated fibres. SEM observations on the fracture surface of composites showed that the surface modification of the fibre occurred and improved fibre–matrix adhesion. Keywords: Surface modification; banana fiber; Biodegradable composites; Mechanical properties; Matrix.

Comparison of Melt Flow and Mechanical Properties of Rice Husk and Kenaf Hybrid Composites

2013 ◽  
Vol 701 ◽  
pp. 42-46 ◽  
Author(s):  
Abd Aziz Noor Zuhaira ◽  
Rahmah Mohamed
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Rice Husk ◽  
Hybrid Composites ◽  
Natural Fibers ◽  
Melt Flow Index ◽  
Silica Content ◽  
Flow Index ◽  
Melt Flow

This research is to identify the difference in melt flow and mechanical properties in hybrid composites between kenaf and rice husk that each of the filler was compounded with composite material of calcium carbonate (CaCO3) and high density polyethylene (HDPE) in different loading amount. Different filler loading up to 30 parts of kenaf fibers and rice husk particulate were mixed with the fixed 30% amount of CaCO3. Compounded hybrid composite were prepared and tested for melt flow index, tensile and impact strength. Addition of both fillers had decreased melt flow index (MFI). MFI of rice husk/CaCO3 was higher than kenaf/CaCO3 in HDPE composites. Tensile strength, elongation at break and impact properties of both hybrid composites had decreased with increasing filler content. Tensile strength of kenaf/CaCO3 was higher than rice husk/CaCO3 due to intrinsic fiber structure of kenaf which has some reinforcing effect compared to rice husk. While, impact strength of rice husk/CaCO3 was improved with addition of filler but drastically decrease as the rice husk content were increased up to 30% due to high silica content in rice husk. The Youngs Modulus was increased with addition of natural fibers in CaCO3/HDPE composite.

scholarly journals STUDI PERBANDINGAN SIFAT MEKANIK SERAT BAMBU

2021 ◽  
Vol 5 (2) ◽  
pp. 383
Author(s):  
Gregoria Illya ◽  
Ika Bali
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
High Performance ◽  
Natural Fiber ◽  
Natural Fibers ◽  
Extraction Methods ◽  
Daily Routine ◽  
Compressive Loads ◽  
Bamboo Fibers ◽  
High Flexibility

Natural fibers have application in almost every item used in our daily routine and been contributing explicitly to the economic prosperity and sustainability in our lives. Among the natural fiber plants, bamboo is the most popular, because of its versatile applications and significant contribution to the environment. Bamboo fibers have been used in various application such as decoration, weaving, paper makin, textile, and high-performance composites for the past many years. They have several advantages such as superior tensile strength, low density, and high flexibility under flexible and compressive loads. In order to meet the requirements of each bamboo application, there is a need to study the mechanical properties of bamboo fibers. This study reviews mechanical properties of bamboo fibers for various species, extraction methods, plant age, sizes, and moisture contents.  Keywords: bamboo fiber; bamboo extraction method; mechanical properties; mechanical testing; tensile strength AbstrakIndonesia kaya akan tanaman yang dapat diambil seratnya untuk diolah menjadi produk yang bermanfaat. Di antara tanaman penghasil serat alami, bambu adalah yang paling populer, karena memiliki aplikasi yang serba guna, mudah tumbuh, tidak memerlukan perawatan dan dapat mengurangi pencemaran udara. Serat bambu telah digunakan dalam berbagai aplikasi seperti dekorasi, perabot, tekstil, kertas dan komposit. Beberapa keunggulan serat bambu adalah memiliki kekuatan tarik yang besar, densitas yang rendah dan fleksibilitas yang tinggi. Dalam rangka memenuhi persyaratan masing-masing aplikasi dari serat bambu, diperlukan studi mengenai sifat mekanik serat bambu. Penelitian ini membandingkan beberapa penelitian yang sudah dilakukan mengenai sifat mekanik serat bambu berdasarkan spesies, metode pengolahan dari batang bambu menjadi serat, umur tanaman, ukuran serat dan kadar kelembaban. Serat bambu yang dihasilkan dapat memiliki sifat mekanik yang optimal jika bambu yang dipilih adalah dari spesies tertentu, memiliki kadar kelembaban yang rendah dan menggunakan metode ekstraksi yang tepat.

Effects of Using Corn Cover Fibers on Some Mechanical Properties of Concrete

2021 ◽  
Vol 895 ◽  
pp. 41-49
Author(s):  
Ali Abbas Kadhem ◽  
Hayder Abbas Al-Yousefi ◽  
Qusay A. Jabal
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Natural Fibers ◽  
Ductile Failure ◽  
Plain Concrete ◽  
Slight Improvement ◽  
Optimum Ratio ◽  
Sudden Failure

This investigation aims to use corn cover as natural fibers in concrete mixes to improve some mechanical properties like compressive strength, tensile strength, and flexural strength. using any type of fiber in concrete, in general, can improve the tensile and flexural strength of concrete. Concrete is weak in tension, so using fibers such as natural fibers like trunk fibers or industrial fibers such as steel fibers can improve tensile, the flexural strength of concrete and that may be decreasing the use of steel reinforcement in concrete, and also fibers can improve toughness and ductility of concrete because of its work inside the concrete that can reduce the propagation of cracks under loading. This study shows slight improvement on compressive strength by using fibers, but high increments in flexural strength, the optimum ratio of corn cover fibers was 2.5% by weight of cement which gives the highest values in compressive strength and flexural strength. compressive strength increased from (31.2 to 35.9) MPa (about 15% increment), increment for flexural strength was 70.6% for the optimum fibers content and the failure by using corn fibers was a ductile failure compared with plain concrete that gives sudden failure under flexure load, also tensile strength increased by using fibers, more fibers content beyond or more than 2.5% give lower values for the mechanical properties.

Effects of Stitching Parameters of Non-Crimp Fabrics on the Mechanical Properties of CFRTP

2010 ◽  
Vol 452-453 ◽  
pp. 301-304
Author(s):  
Kazuto Tanaka ◽  
Masahiro Yamada ◽  
Masahiro Shinohara ◽  
Tsutao Katayama
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Fibre Bundle ◽  
Low Cost ◽  
Inverse Correlation ◽  
Woven Fabrics ◽  
Thickness Direction ◽  
Sem Image ◽  
Disorder Degree ◽  
Sem Image Analysis

The non-crimp fabric (NCF) have an advantageous combination of high material properties and low cost for processing, and overcomes the disadvantages of the crimp factor of woven fabrics, providing full use of modulus and strength of reinforcing fibre. For using NCF, different stitching tension and thread of non-crimp fabrics may cause the mechanical properties of CFRTP. In this study, it is aimed to clarify the effect of stitching tension and thread of non-crimp fabrics on tensile strength of CFRTP. The disorder degree of the thickness direction in the fibre bundle and the ratio of resin rich area were examined by the SEM image analysis. There is the inverse correlation between tensile strength and the disorder degree to the thickness direction in the fibre bundle.

scholarly journals Development and Characterization of Environmentally Friendly Wood Plastic Composites from Biobased Polyethylene and Short Natural Fibers Processed by Injection Moulding

Polymers ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1692
Author(s):  
Celia Dolza ◽  
Eduardo Fages ◽  
Eloi Gonga ◽  
Jaume Gomez-Caturla ◽  
Rafael Balart ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Polymer Matrix ◽  
Fire Behavior ◽  
Natural Fibers ◽  
Environmentally Friendly ◽  
Extrusion Process ◽  
Hemp Fiber ◽  
Wood Plastic Composites ◽  
Lignocellulosic Fibers ◽  
Plastic Composites

Environmentally friendly wood plastic composites (WPC) with biobased high density polyethylene (BioHDPE) as the polymer matrix and hemp, flax and jute short fibers as natural reinforcements, were melt-compounded using twin-screw extrusion and shaped into pieces by injection molding. Polyethylene-graft-maleic anhydride (PE-g-MA) was added at two parts per hundred resin to the WPC during the extrusion process in order to reduce the lack in compatibility between the lignocellulosic fibers and the non-polar polymer matrix. The results revealed a remarkable improvement of the mechanical properties with the combination of natural fibers, along with PE-g-MA, highly improved stiffness and mechanical properties of neat BioHDPE. Particularly, hemp fiber drastically increased the Young’s modulus and impact strength of BioHDPE. Thermal analysis revealed a slight improvement in thermal stability with the addition of the three lignocellulosic fibers, increasing both melting and degradation temperatures. The incorporation of the fibers also increased water absorption due to their lignocellulosic nature, which drastically improved the polarity of the composite. Finally, fire behavior properties were also improved in terms of flame duration, thanks to the ability of the fibers to form char protective barriers that isolate the material from oxygen and volatiles.

scholarly journals Variation of the Mechanical Properties for Natural Fiber Reinforced Composites with Different Weight Ratio of Ziziphus Nummularia’s (Ber) Fibers

2020 ◽  
Vol 8 (6) ◽  
pp. 5393-5397
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Yield Strength ◽  
Fiber Volume Fraction ◽  
Natural Fiber ◽  
Volume Fraction ◽  
Natural Fibers ◽  
Weight Ratio ◽  
Young Modulus ◽  
Fiber Volume

In the present era, Natural fibers are favored for the formation of composites due to their low density, high strength, biodegradability, easy production, low carbon foot, environment friendly nature in comparison of synthetic fibers. This Paper deals with NFRC made from natural fibers obtained from the plants of arid region of Western Rajasthan on which a few researchers are focusing. This paper discuss on the extraction process of fiber from the ber’s stems, manufacturing of composites by using epoxy resin & ber’s fibers then testing of its mechanical properties e.g. tensile strength, young modulus, yield strength , and percentage elongation. Six Sample were made having weight ratio - 0.1, 0.2, 0.3, 0.4, 0.45, & 0. 6. Dog bone samples were prepared according to the ASTM D638 (Type IV) standard. Tensile strength varies from 12.19 MPa to 25 MPa, while young modulus varies from 1.4GPa to 2.9GPa for different weight ratios. Yield strength varies from 10.77 MPa to 21.16 MPa. Percentage of Elongation varies from 1 to 3%. These results shows that ber’s stems can be used for fiber extraction to manufacture composites materials & for better mechanical properties minimum fiber volume fraction percentage is 13% and maximum fiber fraction is 31%.This data can be used further when optimum value of fiber volume fraction is required to form composites from ber’s fibers.

scholarly journals Serat Pelepah Sagu Sebagai Alternatif Pengganti Serat Sintesis Fiberglass

2021 ◽  
Vol 6 (1) ◽  
pp. 14
Author(s):  
Budiawan Sulaeman ◽  
Rakhmawati Natsir
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Composite Material ◽  
Glass Fiber ◽  
Fiber Diameter ◽  
Natural Fibers ◽  
Fiber Volume ◽  
Synthetic Fibers ◽  
Matrix Volume ◽  
Naoh Solution

Tujuan penelitian ini untuk menganalisis pengaruh ukuran besar diameter serat pelepah sagu terhadap sifat mekanik kekuatan tarik, menganalisis sifat mekanik tarik material komposit yang diperkuat serat pelepah sagu.Berdasarkan hasil penelitian; (1). Larutan NAoH berpengaruh terhadap kuat Tarik specimen, hal ini ditunjukkan pada 2,5% (NAoH terhadap H2O). Nilai kekuatan tariknya 49,486 N/mm2. (2). Serat pelepah sagu kuat tariknya jauh dibawah serat gelas. (48,435 N/mm2< 323 N/mm2). Hal ini disebabkan rongga yang terdapat di serat sintesis lebih rapat dibanding serat alami. (3). Berdasarkan variabel yang diteliti, kekuatan tarik (Ftu) dengan nilai tertinggi terjadi pada komposit (volume 85% matriks : 15% serat) yaitu sebesar 3,12 beban 11824 N. (4). Kekuatan tarik mengalami kenaikan terhadap peningkatan komposisi volume serat. (5). Spesimen uji yang mengalami regangan dan patah pada titik load yaitu pada komposisi volume 85% matriks : 15% serat sebesar 3,12 MPa dengan regangan sebesar 8% dan modulus young yang terjadi sebesar 38,615  MPa.The purpose of this study was to analyze the effect of the size of the sago frond fiber diameter on the mechanical properties of the tensile strength, to analyze the tensile mechanical properties of the composite material reinforced by sago frond fibers. Based on research results; (1) NaOH solution affects the tensile strength of the specimen. This is shown at 2.5% (NaOH to H2O), the tensile strength value is 49.486 N/mm2. (2) Sago frond fiber has a tensile strength far below the glass fiber (48,435 N/mm2 <323 N/mm2). This is because the cavities in synthetic fibers are denser than natural fibers. (3) Based on the variables studied, the tensile strength (Ftu) with the highest value occurs in the composite (85% matrix volume: 15% fiber), which is 3.12 load 11824 N. (4) Tensile strength increases with the increase in fiber volume composition. (5) The test specimens that experienced a strain and fracture at the load point, namely the composition of volume 85% matrix: 15% fiber was 3.12 MPa with a strain of 8% and the modulus young that occurred was 38.615 MPa.

Sign in / Sign up

Export Citation Format

Share Document