Assembly Tool Manufacturing and Optimization for Polylactic Acid Additive Manufacturing

2019 ◽  
Vol 952 ◽  
pp. 153-162 ◽  
Author(s):  
Šimon Lecký ◽  
Stefan Václav ◽  
Dávid Michal ◽  
Róbert Hrušecký ◽  
Peter Košťál ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Polylactic Acid ◽  
Manufacturing Process ◽  
Material Selection ◽  
Plastic Material ◽  
Current Trend ◽  
Poly Lactic Acid ◽  
Clean Manufacturing ◽  
Measuring Machine ◽  
Assembly Tool

Paper focuses on additive manufacturing of assembly tool for hole selection. One of the most important part in design and optimization process in additive manufacturing for assembly tool is material selection and technology. In this case was chosen plastic material know as poly-lactic-acid. Polylactic acid has low shrinkage and huge potential in assembly tooling and assembly fixture manufacturing. Main benefits are in use of additive manufacturing for this purpose because of huge manufacturing variability and time savings in case of frequent design changes. From filament fused fabrication technology stand point is important to determine right manufacturing orientation of part. Main material benefit is bio-degradability and recyclability. Current trend in manufacturing is bio materials, clean manufacturing and ecofriendly products. Correct orientation of assembly tool will optimize manufacturing process in one way. Article is aimed on manufacturing precision in each orientation of part on build late. With right orientation of part in additive manufacturing process is determined exact precision of assembly tool manufacturing. For measurement was used coordinate-measuring machine. In this case measurements and precision checking are made only in exact spots where is needed the most precise distance

Evaluation of Parts Produced by a Novel Additive Manufacturing Process

2013 ◽  
Vol 315 ◽  
pp. 63-67 ◽  
Author(s):  
Muhammad Fahad ◽  
Neil Hopkinson
Keyword(s):  
Additive Manufacturing ◽  
Rapid Prototyping ◽  
Manufacturing Process ◽  
High Speed ◽  
Three Dimensional ◽  
Coordinate Measuring Machine ◽  
Layer By Layer ◽  
Nylon 12 ◽  
Measuring Machine ◽  
End Use

Rapid prototyping refers to building three dimensional parts in a tool-less, layer by layer manner using the CAD geometry of the part. Additive Manufacturing (AM) is the name given to the application of rapid prototyping technologies to produce functional, end use items. Since AM is relatively new area of manufacturing processes, various processes are being developed and analyzed for their performance (mainly speed and accuracy). This paper deals with the design of a new benchmark part to analyze the flatness of parts produced on High Speed Sintering (HSS) which is a novel Additive Manufacturing process and is currently being developed at Loughborough University. The designed benchmark part comprised of various features such as cubes, holes, cylinders, spheres and cones on a flat base and the build material used for these parts was nylon 12 powder. Flatness and curvature of the base of these parts were measured using a coordinate measuring machine (CMM) and the results are discussed in relation to the operating parameters of the process.The result show changes in the flatness of part with the depth of part in the bed which is attributed to the thermal gradient within the build envelope during build.

Thermal, structural, and mechanical effects of nanofibrillated cellulose in polylactic acid filaments for additive manufacturing

BioResources ◽  
2020 ◽  
Vol 15 (4) ◽  
pp. 7954-7964
Author(s):  
Diego Gomez-Maldonado ◽  
Maria Soledad Peresin ◽  
Christina Verdi ◽  
Guillermo Velarde ◽  
Daniel Saloni
Keyword(s):  
Tensile Strength ◽  
Additive Manufacturing ◽  
3D Printing ◽  
Polylactic Acid ◽  
Modulus Of Elasticity ◽  
Manufacturing Process ◽  
Thermal Characterization ◽  
Nanofibrillated Cellulose ◽  
Small Decrease ◽  
The Matrix

As the additive manufacturing process gains worldwide importance, the need for bio-based materials, especially for in-home polymeric use, also increases. This work aims to develop a composite of polylactic acid (PLA) and nanofibrillated cellulose (NFC) as a sustainable approach to reinforce the currently commercially available PLA. The studied materials were composites with 5 and 10% NFC that were blended and extruded. Mechanical, structural, and thermal characterization was made before its use for 3D printing. It was found that the inclusion of 10% NFC increased the modulus of elasticity in the filaments from 2.92 to 3.36 GPa. However, a small decrease in tensile strength was observed from 55.7 to 50.8 MPa, which was possibly due to the formation of NFC aggregates in the matrix. This work shows the potential of using PLA mixed with NFC for additive manufacturing.

scholarly journals Magnesium Filled Polylactic Acid (PLA) Material for Filament Based 3D Printing

Materials ◽  
2019 ◽  
Vol 12 (5) ◽  
pp. 719 ◽  
Author(s):  
Iulian Antoniac ◽  
Diana Popescu ◽  
Aurelian Zapciu ◽  
Aurora Antoniac ◽  
Florin Miculescu ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Vitamin E ◽  
Polylactic Acid ◽  
Manufacturing Process ◽  
Structural Integrity ◽  
Low Cost ◽  
Cruciate Ligament ◽  
Infrared Spectrometry ◽  
Scanning Calorimetry ◽  
Anterior Cruciate

The main objective of this research is to prove the viability of obtaining magnesium (Mg) filled polylactic acid (PLA) biocomposites as filament feedstock for material extrusion-based additive manufacturing (AM). These materials can be used for medical applications, thus benefiting of all the advantages offered by AM technology in terms of design freedom and product customization. Filaments were produced from two PLA + magnesium + vitamin E (α-tocopherol) compositions and then used for manufacturing test samples and ACL (anterior cruciate ligament) screws on a low-cost 3D printer. Filaments and implant screws were characterized using SEM (scanning electron microscopy), FTIR (fourier transform infrared spectrometry), and DSC (differential scanning calorimetry) analysis. Although the filament manufacturing process could not ensure a uniform distribution of Mg particles within the PLA matrix, a good integration was noticed, probably due to the use of vitamin E as a precursor. The results also show that the composite biomaterials can ensure and maintain implant screws structural integrity during the additive manufacturing process.

scholarly journals Uncertainty assessment for measurement and simulation in selective laser melting: a case study of an aerospace part

ACTA IMEKO ◽  
2020 ◽  
Vol 9 (4) ◽  
pp. 96
Author(s):  
Giulio D'Emilia ◽  
Antoniomaria Di Ilio ◽  
Antonella Gaspari ◽  
Emanuela Natale ◽  
Antonios G. Stamopoulos
Keyword(s):  
Additive Manufacturing ◽  
Selective Laser Melting ◽  
Manufacturing Process ◽  
Thermal Stresses ◽  
Hybrid Approach ◽  
Coordinate Measuring Machine ◽  
Thermal Treatments ◽  
Laser Melting ◽  
Measuring Machine ◽  
Simulation Results

<p class="Abstract"><span lang="EN-US">In this work, the additive manufacturing process selective laser melting is analysed with the aim of realising a complex piece for aerospace applications. In particular, the effect of the manufacturing process and of the following thermal treatments on the dimensions of the workpiece is evaluated. The study is based on a hybrid approach including a simulation of the whole manufacturing process by advanced software packages and the dimensional measurements of the realised pieces taken by a coordinate measuring machine (CMM). The integrated use of simulation and measurements is carried out with the aim of validating the simulation results and of identifying the operational limits of both approaches; this analysis is based on metrological evaluation of the results of both the simulation and the tests, taking into account the uncertainty of the data. In addition, the main causes of uncertainty for the simulation activity and the experimental data have been identified, and the effects of some of them have also been experimentally evaluated. Based on the experimental validation, the simulation seems to predict the absolute displacement of the supports of the piece in a satisfactory way, while it is unable, in the actual configuration, to assess the conformity of the surface to its very tight shape tolerances. Conformity assessment of the surface should be carried out by CMM measurement. Integrated use of simulation and experimental results is expected to strongly improve the accuracy of simulation results for the effective and accurate design and control of the additive manufacturing process, including dimensional control and thermal treatments to mitigate induced thermal stresses.</span></p>

Preliminary Study on Effects of the Process Parameters on Mechanical Properties in Liquid Holographic Volumetric Additive Manufacturing Process

2019 ◽  
Author(s):  
Sagil James ◽  
Thilakraj Shivakumar
Keyword(s):  
Mechanical Properties ◽  
Additive Manufacturing ◽  
3D Printing ◽  
Manufacturing Process ◽  
Material Selection ◽  
Primary Source ◽  
Limited Range ◽  
Printing Technology ◽  
3D Printing Technology ◽  
Light Beams

Abstract The momentum of the additive manufacturing research is on a spurt. Additive manufacturing, also known as 3D printing process has been attracting the attention of the manufacturing community worldwide over the past decade. The 3D printing technology promises significant advances and applications in the area of automobiles, electronics, and medical devices and so on. However, this technology currently suffers from several limitations including large time consumption, need for support structures and limited range of material selection. This prevents its application in mass production. Holographic 3D printing, also referred to as (volumetric additive manufacturing) process is a very recent technique which uses multiple light beams intensified to form a build volume. A photosensitive liquid resin is solidified using the principle of constructive interference. The single light beam is not enough to produce the required intensity to cure the resin. While the combined interference could generate the required energy. The resulting part is printed in a fraction of seconds at once in contrast with the traditional 3D printing technology. This research studies the feasibility of a novel holographic volumetric additive manufacturing with an ultraviolet source of 365 nm as the primary source of energy. This propels the polymeric photochemical reaction between the monomer molecules. Also, experiments are conducted, incorporating various viscosity levels of the photopolymer material to suppress the oxygen dissolution. At the same time to observe the rate of curing of the photopolymer material. Finally, the mechanical properties of the build volume are analyzed.

scholarly journals Design of Shape Memory Thermoplastic Material Systems for FDM-Type Additive Manufacturing

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4254
Author(s):  
Paulina A. Quiñonez ◽  
Leticia Ugarte-Sanchez ◽  
Diego Bermudez ◽  
Paulina Chinolla ◽  
Rhyan Dueck ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Shape Memory ◽  
Thermomechanical Processing ◽  
Material Selection ◽  
Shape Memory Polymer ◽  
Fused Filament Fabrication ◽  
Materials Development ◽  
Thermoplastic Material ◽  
Polymer Systems ◽  
Injection Molded

The work presented here describes a paradigm for the design of materials for additive manufacturing platforms based on taking advantage of unique physical properties imparted upon the material by the fabrication process. We sought to further investigate past work with binary shape memory polymer blends, which indicated that phase texturization caused by the fused filament fabrication (FFF) process enhanced shape memory properties. In this work, two multi-constituent shape memory polymer systems were developed where the miscibility parameter was the guide in material selection. A comparison with injection molded specimens was also carried out to further investigate the ability of the FFF process to enable enhanced shape memory characteristics as compared to other manufacturing methods. It was found that blend combinations with more closely matching miscibility parameters were more apt at yielding reliable shape memory polymer systems. However, when miscibility parameters differed, a pathway towards the creation of shape memory polymer systems capable of maintaining more than one temporary shape at a time was potentially realized. Additional aspects related to impact modifying of rigid thermoplastics as well as thermomechanical processing on induced crystallinity are also explored. Overall, this work serves as another example in the advancement of additive manufacturing via materials development.

scholarly journals Blade Segment with a 3D Lattice of Diamond Grits Fabricated via an Additive Manufacturing Process

2020 ◽  
Vol 33 (1) ◽  
Author(s):  
Bin Chen ◽  
Peng Chen ◽  
Yongjun Huang ◽  
Xiangxi Xu ◽  
Yibo Liu ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Service Life ◽  
Manufacturing Process ◽  
Cutting Speed ◽  
Inspection System ◽  
Layer By Layer ◽  
Filling Rate ◽  
Pressure System ◽  
Manufacturing Equipment ◽  
Diamond Blade

Abstract Diamond tools with orderly arrangements of diamond grits have drawn considerable attention in the machining field owing to their outstanding advantages of high sharpness and long service life. This diamond super tool, as well as the manufacturing equipment, has been unavailable to Chinese enterprises for a long time due to patents. In this paper, a diamond blade segment with a 3D lattice of diamond grits was additively manufactured using a new type of cold pressing equipment (AME100). The equipment, designed with a rotary working platform and 16 molding stations, can be used to additively manufacture segments with diamond grits arranged in an orderly fashion, layer by layer; under this additive manufacturing process, at least 216000 pcs of diamond green segments with five orderly arranged grit layers can be produced per month. The microstructure of the segment was observed via SEM and the diamond blade fabricated using these segments was compared to other commercial cutting tools. The experimental results showed that the 3D lattice of diamond grits was formed in the green segment. The filling rate of diamond grits in the lattice could be guaranteed to be above 95%; this is much higher than the 90% filling rate of the automatic array system (ARIX). When used to cut stone, the cutting amount of the blade with segments made by AME100 is two times that of ordinary tools, with the same diamond concentration. When used to dry cut reinforced concrete, its cutting speed is 10% faster than that of ARIX. Under wet cutting conditions, its service life is twice that of ARIX. By applying the machine vision online inspection system and a special needle jig with a negative pressure system, this study developed a piece of additive manufacturing equipment for efficiently fabricating blade segments with a 3D lattice of diamond grits.

Fused Filament Fabrication 3D Printed Polylactic Acid Electroosmotic Pumps

Lab on a Chip ◽  
2021 ◽  
Author(s):  
Liang Wu ◽  
Stephen Beirne ◽  
Joan-Marc Cabot Canyelles ◽  
Brett Paull ◽  
Gordon G. Wallace ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
3D Printing ◽  
Polylactic Acid ◽  
Fused Filament Fabrication ◽  
Flexible Approach ◽  
Electroosmotic Pump ◽  
3D Printed ◽  
Electroosmotic Pumps

Additive manufacturing (3D printing) offers a flexible approach for the production of bespoke microfluidic structures such as the electroosmotic pump. Here a readily accessible fused filament fabrication (FFF) 3D printing...

scholarly journals Variable low-density polylactic acid and microsphere composite material for additive manufacturing

2021 ◽  
pp. 101925
Author(s):  
Henrik Andersson ◽  
Jonas Örtegren ◽  
Renyun Zhang ◽  
Markus Grauers ◽  
Håkan Olin
Keyword(s):  
Composite Material ◽  
Additive Manufacturing ◽  
Polylactic Acid ◽  
Low Density
Sign in / Sign up

Export Citation Format

Share Document