Microstructures and Dielectric Properties of CaCu3Ti4O12 Polycrystalline Ceramics

2007 ◽  
Vol 124-126 ◽  
pp. 143-146 ◽  
Author(s):  
Duk Keun Yoo ◽  
Sang Im Yoo
Keyword(s):  
Dielectric Properties ◽  
Sintered Density ◽  
Dielectric Constants ◽  
Abrupt Increase ◽  
Factors Affecting ◽  
Polycrystalline Ceramics ◽  
State Ceramic ◽  
Ceramic Process ◽  
Ccto Sample ◽  
Very High

We report important factors affecting the dielectric properties of CaCu3Ti4O12 (CCTO) polycrystalline ceramics prepared by the conventional solid-state ceramic process. The relative dielectric constants (εr) up to several thousands (~ 3,000 at 1 kHz) were gradually increased with increasing the sintered density of samples in the case that no exaggerated grain growth occurred. An abrupt increase in εr values were, however, accompanied by the formation of abnormally grown large grains, and thus with increasing the population of abnormally grown grains, which could be achieved by a prolonged sintering at 1060°C, the εr values were remarkably increased from several thousands to ~105. Optimally processed CCTO sample exhibited a very high εr of ~ 90,000 at 1 kHz.

Microwave dielectric properties of MO–La2O3–TiO2 (M = Ca, Sr, Ba) ceramics

2002 ◽  
Vol 17 (12) ◽  
pp. 3084-3089 ◽  
Author(s):  
Isuhak Naseemabeevi Jawahar ◽  
Narayana Iyer Santha ◽  
Mailadil Thomas Sebastian ◽  
Pezholil Mohanan
Keyword(s):  
Dielectric Properties ◽  
Single Phase ◽  
Microwave Dielectric Properties ◽  
Quality Factors ◽  
X Ray Diffraction ◽  
Microwave Dielectric ◽  
Narrow Bandwidth ◽  
Polycrystalline Ceramics ◽  
State Ceramic ◽  
High Dielectric

Single-phase polycrystalline ceramics in the MO–La2O3–TiO2 (M = Ca, Sr, Ba) system, such as cation-deficient hexagonal perovskites CaLa4Ti4O15, SrLa4Ti4O15, BaLa4Ti4O15, and Ca2La4Ti5O18 and the orthorhombic phases CaLa4Ti5O17 and CaLa8Ti9O31, were prepared through the solid-state ceramic route. The phases and structure of the ceramics were analyzed through x-ray diffraction and scanning electron microscopy. The microwave dielectric properties of the ceramics were studied using a network analyzer. The investigated ceramics show high εr in the range 42 to 54, high quality factors with Q ×f in the range 16,222 to 50,215 GHz, and low Tf in the range –25 to +6 ppm / °C. These high dielectric constant materials with high Q × f up to 50,215 GHz are suitable for applications where narrow bandwidth and extremely low insertion loss is necessary, especially at frequencies around 1.9 GHz.

High-Temperature Dielectric Properties of Polycrystalline Ceramics

1988 ◽  
Vol 124 ◽  
Author(s):  
W. W. Ho
Keyword(s):  
High Temperature ◽  
Dielectric Properties ◽  
Volume Expansion ◽  
Room Temperature ◽  
Experimental Methods ◽  
Dielectric Constants ◽  
Amorphous Phases ◽  
Temperature Loss ◽  
Polycrystalline Ceramics ◽  
Impurity Doping

ABSTRACTExperimental methods for determining the high-temperature millimeter-wave dielectric properties of solids are described and the data obtained on a wide variety of polycrystalline ceramics are reviewed. In general, the observed increase in dielectric constants with temperature can be modeled with a macroscopic dielectric virial expansion and shown to be primarily caused by an increase in polarizability due to volume expansion. The room-temperature loss tangents in low-absorption ceramics are probably caused by impurity doping of the primary and secondary crystalline phases at grain junctions and along grain boundaries. The rapid increase in loss tangent at high temperatures commonly observed in polycrystalline ceramics is associated with softening of intergranular amorphous phases resulting in an increase in localized electrical conductivity.

scholarly journals The Primary Origin of Excellent Dielectric Properties of (Co, Nb) Co-Doped TiO2 Ceramics: Electron-Pinned Defect Dipoles vs. Internal Barrier Layer Capacitor Effect

Molecules ◽  
2021 ◽  
Vol 26 (11) ◽  
pp. 3230
Author(s):  
Theeranuch Nachaithong ◽  
Narong Chanlek ◽  
Pairot Moontragoon ◽  
Prasit Thongbai
Keyword(s):  
Dielectric Properties ◽  
Loss Tangent ◽  
Barrier Layer ◽  
Dielectric Response ◽  
High Resistivity ◽  
Low Loss ◽  
Rutile Tio2 ◽  
Complex Defect ◽  
Very High ◽  
Co Doped

(Co, Nb) co-doped rutile TiO2 (CoNTO) nanoparticles with low dopant concentrations were prepared using a wet chemistry method. A pure rutile TiO2 phase with a dense microstructure and homogeneous dispersion of the dopants was obtained. By co-doping rutile TiO2 with 0.5 at.% (Co, Nb), a very high dielectric permittivity of ε′ » 36,105 and a low loss tangent of tanδ » 0.04 were achieved. The sample–electrode contact and resistive outer-surface layer (surface barrier layer capacitor) have a significant impact on the dielectric response in the CoNTO ceramics. The density functional theory calculation shows that the 2Co atoms are located near the oxygen vacancy, creating a triangle-shaped 2CoVoTi complex defect. On the other hand, the substitution of TiO2 with Nb atoms can form a diamond-shaped 2Nb2Ti complex defect. These two types of complex defects are far away from each other. Therefore, the electron-pinned defect dipoles cannot be considered the primary origins of the dielectric response in the CoNTO ceramics. Impedance spectroscopy shows that the CoNTO ceramics are electrically heterogeneous, comprised of insulating and semiconducting regions. Thus, the dielectric properties of the CoNTO ceramics are attributed to the interfacial polarization at the internal insulating layers with very high resistivity, giving rise to a low loss tangent.

scholarly journals Dielectric Properties of Wood-Polymer Composites: Effects of Frequency, Fiber Nature, Proportion, and Chemical Composition

2021 ◽  
Vol 5 (6) ◽  
pp. 141
Author(s):  
Imen Elloumi ◽  
Ahmed Koubaa ◽  
Wassim Kharrat ◽  
Chedly Bradai ◽  
Ahmed Elloumi
Keyword(s):  
Dielectric Properties ◽  
Polymer Composites ◽  
Wide Frequency Range ◽  
Dielectric Constants ◽  
Cellulose Content ◽  
Wood Fibers ◽  
Low Frequencies ◽  
Wood Polymer ◽  
Wood Polymer Composites ◽  
New Applications

The characterization of the dielectric properties of wood–polymer composites (WPCs) is essential to understand their interaction with electromagnetic fields and evaluate their potential use for new applications. Thus, dielectric spectroscopy monitored the evolution of the dielectric properties of WPCs over a wide frequency range of 1 MHz to 1 GHz. WPCs were prepared using mixtures of different proportions (40%, 50%, and 60%) of wood and bark fibers from various species, high-density polyethylene, and maleated polyethylene (3%) by a two-step process, extrusion and compression molding. Results indicated that wood fibers modify the resistivity of polyethylene at low frequencies but have no effect at microwave frequencies. Increasing the fiber content increases the composites’ dielectric properties. The fibers’ cellulose content explains the variation in the dielectric properties of composites reinforced with fibers from different wood species. Indeed, composites with high cellulose content show higher dielectric constants.

scholarly journals Sintering, Microstructure, and Dielectric Properties of Copper Borates for High Frequency LTCC Applications

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 4017
Author(s):  
Dorota Szwagierczak ◽  
Beata Synkiewicz-Musialska ◽  
Jan Kulawik ◽  
Norbert Pałka
Keyword(s):  
Dielectric Properties ◽  
Dielectric Permittivity ◽  
High Frequency ◽  
Ceramic Materials ◽  
Sintering Behavior ◽  
Terahertz Time Domain Spectroscopy ◽  
Very High Frequency ◽  
X Ray ◽  
Low Dielectric ◽  
Very High

New ceramic materials based on two copper borates, CuB2O4 and Cu3B2O6, were prepared via solid state synthesis and sintering, and characterized as promising candidates for low dielectric permittivity substrates for very high frequency circuits. The sintering behavior, composition, microstructure, and dielectric properties of the ceramics were investigated using a heating microscope, X-ray diffractometry, scanning electron microscopy, energy dispersive spectroscopy, and terahertz time domain spectroscopy. The studies revealed a low dielectric permittivity of 5.1–6.7 and low dielectric loss in the frequency range 0.14–0.7 THz. The copper borate-based materials, owing to a low sintering temperature of 900–960 °C, are suitable for LTCC (low temperature cofired ceramics) applications.

scholarly journals Comparative Evaluation of Orthostatic Hypotension in Patients with Diabetic Nephropathy

2021 ◽  
pp. 1-7
Author(s):  
Gamze Aytaş ◽  
Rümeyza Kazancıoğlu ◽  
Ömer C. Elçioğlu ◽  
Meltem Gürsu ◽  
A. Serra Artan ◽  
...  
Keyword(s):  
Diabetic Nephropathy ◽  
Orthostatic Hypotension ◽  
Electronic Device ◽  
Channel Blockers ◽  
Factors Affecting ◽  
Clinical Criteria ◽  
Measure Blood Pressure ◽  
Significant Difference ◽  
Male Patients ◽  
Very High

<b><i>Introduction:</i></b> Orthostatic hypotension (OH) affects 5–20% of the population. Our study investigates the presence of OH in diabetic nephropathy (DNP) patients and the factors affecting OH in comparison with nondiabetic chronic kidney disease (NDCKD) patients. <b><i>Method:</i></b> Patients presented to the nephrology clinic, and those who consented were included in the study. DNP was defined by kidney biopsy and/or clinical criteria. NDCKD patients of the same sex, age, and eGFR were matched to DNP patients. Demographic parameters and medications were obtained from the records. OH was determined by Mayo clinic criteria. The same researcher used an electronic device to measure blood pressure (BP). All samples were taken and analyzed the same day for biochemical and hematologic parameters and albuminuria. <b><i>Results:</i></b> 112 (51 F, 61 M, mean age: 62.56 ± 9.35 years) DNP and 94 (40 F, 54 M, mean age: 62.23 ± 10.08 years) NDCKD patients were included. There was no significant difference between DNP and NDCKD groups in terms of OH prevalence (70.5 vs. 61.7%, <i>p</i> = 0.181). Male patients had significantly higher OH prevalence than female patients (74.7 vs. 60.0%, <i>p</i> = 0.026). There was no significant difference in change in systolic BP between the groups (24.00 [10.00–32.00] mm Hg vs. 24.00 [13.75–30.25] mm Hg, <i>p</i> = 0.797), but the change in diastolic BP was significantly higher in the DNP group (8.00 [2.00–13.00] mm Hg vs. 6.00 [2.00–9.00] mm Hg, <i>p</i> = 0.025). In the DNP group, patients with OH had significantly higher uric acid levels than those without OH (7.18 ± 1.55 vs. 6.36 ± 1.65 mg/dL, <i>p</i> = 0.017). And, 73.7% of patients on calcium channel blockers developed OH (<i>p</i> = 0.015), and OH developed in 80.6% of 36 patients on alpha-blockers (<i>p</i> = 0.049). <b><i>Conclusion:</i></b> OH prevalence is very high in CKD, and etiology of CKD does not have a statistically significant effect on the frequency of OH, despite a difference that could be meaningful clinically. Therefore, patients with CKD are checked for OH, with or without concurrent diabetes mellitus. Evaluation of postural BP changes should be a part of nephrology practice.

Sintering and dielectric properties of (Ta2O5)1−x (TiO2) x polycrystalline ceramics

2007 ◽  
Vol 21 (1-4) ◽  
pp. 577-580 ◽  
Author(s):  
Yue Wang ◽  
Xue-wen Zhu ◽  
Yi-jian Jiang
Keyword(s):  
Dielectric Properties ◽  
Polycrystalline Ceramics

Crystallization and dielectric properties of SrO–BaO–Nb2O5–GeO2 tungsten–bronze glass–ceramics

2001 ◽  
Vol 16 (7) ◽  
pp. 2057-2063 ◽  
Author(s):  
Jiin-Jyh Shyu ◽  
Hsin-Wei Peng
Keyword(s):  
Heat Treatment ◽  
Dielectric Properties ◽  
Tungsten Bronze ◽  
Glass Ceramics ◽  
Dielectric Behavior ◽  
Dendritic Morphology ◽  
Dielectric Constants ◽  
Two Stage ◽  
Tetragonal Tungsten Bronze ◽  
Stage Heat Treatment

The crystallization and dielectric properties of SrO–BaO–Nb2O5–GeO2 glass–ceramics were investigated. One- and two-stage heat-treatment methods were used to convert the parent glass to glass–ceramics. Strontium barium niobate (SBN) with a tetragonal tungsten-bronze structure formed as the major crystalline phase. When the crystallizing temperature/time was increased, the secondary crystalline BaGe2O5 phase coexisted with SBN. BaGe2O5 formed as a surface layer grown from the surface into the interior of the sample. The dendritic morphology of SBN crystals was examined. The glass–ceramics crystallized by two-stage heat treatment have higher dielectric constants than those crystallized by one-stage heat treatment. The highest dielectric constant that was obtained in the present glass–ceramics was 320. The glass–ceramics showed relaxor-type dielectric behavior.

Epitaxial Growth and Anisotropic Dielectric Properties of La-Doped Bi4Ti3O12 Thin Films

2007 ◽  
Vol 124-126 ◽  
pp. 177-180
Author(s):  
Jang Sik Lee ◽  
Q.X. Jia
Keyword(s):  
Thin Films ◽  
Dielectric Constant ◽  
Dielectric Properties ◽  
Bottom Electrode ◽  
Dielectric Constants ◽  
The Other ◽  
Field Range ◽  
Anisotropic Dielectric ◽  
Dielectric Nonlinearity ◽  
La Doped

To investigate the anisotropic dielectric properties of layer-structured bismuth-based ferroelectrics along different crystal directions, we fabricate devices along different crystal orientations using highly c-axis oriented Bi3.25La0.75Ti3O12 (BLT) thin films on (001) LaAlO3 (LAO) substrates. Experimental results have shown that the dielectric properties of the BLT films are highly anisotropic along different crystal directions. The dielectric constants (1MHz at 300 K) are 358 and 160 along [100] and [110], respectively. Dielectric nonlinearity is also detected along these crystal directions. On the other hand, a much smaller dielectric constant and no detectable dielectric nonlinearity in a field range of 0-200 kV/cm are observed for films along [001] when c-axis oriented SRO is used as the bottom electrode.

Sign in / Sign up

Export Citation Format

Share Document