Utilization of Crushed Glass Waste in Concrete Samples Prepared with Coal Fly Ash

2015 ◽  
Vol 244 ◽  
pp. 102-107 ◽  
Author(s):  
Jozef Junak
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Coal Fly Ash ◽  
Hardened Concrete ◽  
Glass Cullet ◽  
Glass Bottle ◽  
Glass Waste ◽  
Positive Effects ◽  
Natural Aggregate

This article is aimed on the study of glass bottle cullet influence on the compressive and flexural strength development of products prepared as the partial natural aggregate replacement by crushed glass waste. For this study, eight different mixtures containing coloured glass cullet as a full replacement of natural aggregate fractions 0/4, 4/8 and 8/16 mm and two comparative mixtures were prepared. In four of these mixtures, 25% of Portland cement were replaced by coal fly ash. After 7, 28 and 90 days of hardening, samples were tested on flexural strength and compression strength. Results showed, that specimens containing full replacement of fraction 8/16 mm of glass cullet reached the highest compressive strength 43.32 MPa corresponding to concrete strength class C 30/37. Partial cement replacement by coal fly ash leads to low compressive strength after 7, 28 and 90 days of curing. Use of coloured glass bottle cullet in concrete should not have negative impact on the strength characteristics of hardened concrete and should have positive effects for preparing quality fair-faced concrete surfaces.

Effects of Calcium Carbide Sludge on Properties of Steam Curing Brick Prepared by Extracted Aluminum Fly Ash

2012 ◽  
Vol 174-177 ◽  
pp. 1516-1519
Author(s):  
Li Guang Xiao ◽  
Rui Bo Li ◽  
Shi Ting Zhang ◽  
Hong Liang Hu
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Water Absorption ◽  
Frost Resistance ◽  
Coal Fly Ash ◽  
Calcium Carbide ◽  
Chemical Plants ◽  
Steam Curing ◽  
Ash Residue

Because the fly ash will produce large amounts of the secondary waste emission after the extraction of aluminum, the utilization of the fly ash residue after the extraction of aluminum has great significance. The autoclaved fly ash bricks studied in this paper use CFB ash residue after extraction of aluminum as the main material, and calcium carbide clay which consists mainly of calcium hydroxide is the waste residua of the production of acetylene gas in the chemical plants. This paper analyzes the chemical composition, the mineral composition and the microstructure of the fly ash residue after extraction of aluminum. In the paper, we also study the law and impacts of compressive strength, flexural strength, frost resistance and water absorption, which are made by calcium carbide clay for the autoclaved fly ash bricks. Experimental results illustrate that calcium carbide clay can significantly improve the compressive strength, the flexural strength and the frost resistance of the coal fly ash autoclaved bricks, and significantly reduce its water absorption.

scholarly journals Assessment of the Rheological and Mechanical Properties of Geopolymer Concrete Comprising Fly Ash and Fluid Catalytic Cracking Residue as Aluminosilicate Precursor

2021 ◽  
Vol 11 (7) ◽  
pp. 3032
Author(s):  
Tuan Anh Le ◽  
Sinh Hoang Le ◽  
Thuy Ninh Nguyen ◽  
Khoa Tan Nguyen
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Fly Ash ◽  
Flexural Strength ◽  
Catalytic Cracking ◽  
Fluid Catalytic Cracking ◽  
High Alumina ◽  
Geopolymer Concrete ◽  
Sem Images

The use of fluid catalytic cracking (FCC) by-products as aluminosilicate precursors in geopolymer binders has attracted significant interest from researchers in recent years owing to their high alumina and silica contents. Introduced in this study is the use of geopolymer concrete comprising FCC residue combined with fly ash as the requisite source of aluminosilicate. Fly ash was replaced with various FCC residue contents ranging from 0–100% by mass of binder. Results from standard testing methods showed that geopolymer concrete rheological properties such as yield stress and plastic viscosity as well as mechanical properties including compressive strength, flexural strength, and elastic modulus were affected significantly by the FCC residue content. With alkali liquid to geopolymer solid ratios (AL:GS) of 0.4 and 0.5, a reduction in compressive and flexural strength was observed in the case of geopolymer concrete with increasing FCC residue content. On the contrary, geopolymer concrete with increasing FCC residue content exhibited improved strength with an AL:GS ratio of 0.65. Relationships enabling estimation of geopolymer elastic modulus based on compressive strength were investigated. Scanning electron microscope (SEM) images and X-ray diffraction (XRD) patterns revealed that the final product from the geopolymerization process consisting of FCC residue was similar to fly ash-based geopolymer concrete. These observations highlight the potential of FCC residue as an aluminosilicate source for geopolymer products.

scholarly journals Production of ceramics from coal fly ash

2012 ◽  
Vol 18 (2) ◽  
pp. 245-254 ◽  
Author(s):  
Biljana Angjusheva ◽  
Emilija Fidancevska ◽  
Vojo Jovanov
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Solid State ◽  
Liquid Phase ◽  
Bending Strength ◽  
Coal Fly Ash ◽  
Liquid Phase Sintering ◽  
Heating Rates ◽  
Republic Of Macedonia ◽  
The Subject

Dense ceramics are produced from fly ash from REK Bitola, Republic of Macedonia. Four types of fly ash from electro filters and one from the collected zone with particles < 0.063 mm were the subject of this research. Consolidation was achieved by pressing (P= 133 MPa) and sintering (950, 1000, 1050 and 11000C and heating rates of 3 and 100/min). Densification was realized by liquid phase sintering and solid state reaction where diopside [Ca(Mg,Al)(Si,Al)2O6] was formed. Ceramics with optimal properties (porosity 2.96?0.5%, bending strength - 47.01?2 MPa, compressive strength - 170 ?5 MPa) was produced at 1100?C using the heating rate of 10?C/min.

scholarly journals Strength Time–Varying and Freeze–Thaw Durability of Sustainable Pervious Concrete Pavement Material Containing Waste Fly Ash

2018 ◽  
Vol 11 (1) ◽  
pp. 176 ◽  
Author(s):  
Hanbing Liu ◽  
Guobao Luo ◽  
Longhui Wang ◽  
Yafeng Gong
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Pervious Concrete ◽  
Early Age ◽  
Pavement Materials ◽  
Freeze Thaw ◽  
Replacement Method ◽  
Porosity And Permeability ◽  
Volume Method

Pervious concretes, as sustainable pavement materials, have great advantages in addressing a number of environmental issues. Fly ash, as the industrial by-product waste, is the most commonly used as cement substitute in concrete. The objective of this paper is to study the effects of waste fly ash on properties of pervious concrete. Fly ash was used to replace cement with equivalent volume method at different levels (3%, 6%, 9%, and 12%). The control pervious concrete and fly ash modified pervious concrete were prepared in the laboratory. The porosity, permeability, compressive strength, flexural strength, and freeze–thaw resistance of all mixtures were tested. The results indicated that the addition of fly ash decreased the early-age (28 d) compressive strength and flexural strength, but the long-term (150 d) compressive strength and flexural strength of fly ash modified pervious concrete were higher than that of the early-age. The adverse effect of fly ash on freeze–thaw resistance of pervious concrete was observed when the fly ash was added. The porosity and permeability of all pervious concrete mixtures changed little with the content of fly ash due to the use of equal volume replacement method. Although fly ash is not positive to the properties of pervious concrete, it is still feasible to apply fly ash as a substitute for cement in pervious concrete.

An Investigation of Usability of Brown Coal Fly Ash for Building Materials

2013 ◽  
Vol 438-439 ◽  
pp. 30-35 ◽  
Author(s):  
Nirdosha Gamage ◽  
Sujeeva Setunge ◽  
Kasuni Liyanage
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Brown Coal ◽  
Water Contamination ◽  
Building Materials ◽  
Coal Fly Ash ◽  
Sustainable Building ◽  
Laboratory Investigations ◽  
Cold Pressed ◽  
Initial Results

The Victoria State of Australia has the second largest reserves of brown coal on earth, representing approximately 20% of the worlds reserves, and at current use, could supply Victoria with its energy for over 500 years. Its combustion, annually, yields up to 1.3 million tonnes of fly ash, which is largely use for land-fills. Disposal of fly ash in open dumps cause massive environmental problems such as ground water contamination that may create various health problems. This study focuses on the usability of brown coal fly ash to develop a sustainable building material. A series of laboratory investigations was conducted using brown coal fly ash combined with cement and aggregate to prepare cold pressed samples aiming to test their properties. Initial results indicate that compressive strength satisfies minimum standard compressive strength required for bricks or mortar.

The Effect of Substituting Rdf on the Physical and Environmental Properties of Coal Fly Ash

1988 ◽  
Vol 136 ◽  
Author(s):  
Ashaari B. Mohamad ◽  
David L. Gress
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Physical Properties ◽  
Activity Index ◽  
Coal Fly Ash ◽  
Pozzolanic Activity ◽  
Portland Cement Concrete ◽  
Fly Ash Concrete ◽  
Refuse Derived Fuel ◽  
Cadmium And Lead

ABSTRACTRefuse-derived-fuel (RDF) consisting mainly of waste paper and plastics is a viable fuel source for the production of power. An experimental test burn partially substituting coal with RDF was undertaken by the Public Service of New Hampshire at the Merrimack Power Station.Five percent and ten percent RDF were substituted, on a BTU basis, for coal in the test bums. The chemical and physical properties of the resulting fly ash were determined. Twelve test burn days were run with 4 days of 5% RDF and 8 days of 10% RDF. Emphasis was placed on investigating the effect of the RDF fly ash on Portland cement concrete.Most of the chemical and physical properties of the coal-RDF fly ash were found to be comparable with ordinary coal fly ash except for the amount of cadmium and lead, the pozzolanic activity index and the compressive strength of fly ash concrete. Cadmium and lead were at average levels of 5.1 ppm and 102.6 ppm for the 5% RDF, and 7.8 ppm and 198.3 ppm for the 10% RDF, respectively. Although the pozzolanic activity index of coal-RDF fly ash increases over normal coal fly ash, preliminary results show that the 28-day compressive strength of concrete with direct replacement of cement and sand decreases by up to 30%. Leaching tests on crushed concrete were conducted to evaluate the environmental effect of acid rain.

scholarly journals Utilization of Electroplating Sludge as Subgrade Backfill Materials: Mechanical and Environmental Risk Evaluation

2018 ◽  
Vol 2018 ◽  
pp. 1-9 ◽  
Author(s):  
Yu Zhang ◽  
Peixin Shi ◽  
Lijuan Chen ◽  
Qiang Tang
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Water Content ◽  
Environmental Risk ◽  
Coal Fly Ash ◽  
Surrounding Environment ◽  
Electroplating Sludge ◽  
Backfill Materials ◽  
Standard Limit ◽  
The Impact

The electroplating sludge may pose serious threat to human health and surrounding environment without safe treatment. This paper investigated the feasibility of using electroplating sludge as subgrade backfill materials, by evaluating the mechanical properties and environmental risk of the cement-coal fly ash solidified sludge. In this study, Portland cement and coal fly ash are used to solidify/stabilize the sludge. After curing for 7, 14, and 28 days, the stabilization/solidification sludge specimens were subject to a series of mechanical, leaching, and microcosmic tests. It was found that the compressive strength increased with the increase of cement content, curing time, and the cement replacement by coal fly ash besides water content. Among these factors, the impact of water content on the compressive strength is most noticeable. It was observed that the compressive strength declined by 87.1% when the water content increased from 0% to 10%. Besides, leaching tests showed that the amount of leaching heavy metals were under the standard limit. These results demonstrated utilization of electroplating sludge in subgrade backfill material may provide an alternative for the treatment of electroplating sludge.

scholarly journals Long-term mechanical and shrinkage properties of cementitious grouts for structural repair

2019 ◽  
Vol 4 ◽  
pp. 9-15
Author(s):  
Md Shamsuddoha ◽  
Götz Hüsken ◽  
Wolfram Schmidt ◽  
Hans-Carsten Kühne ◽  
Matthias Baeßler
Keyword(s):  
Fly Ash ◽  
Flexural Strength ◽  
Cementitious Materials ◽  
Response Surfaces ◽  
Supplementary Cementitious Materials ◽  
Strength Development ◽  
Structural Repair ◽  
Positive Effects ◽  
Micro Silica

Grouts have numerous applications in construction industry such as joint sealing, structural repair, and connections in precast elements. They are particularly favoured in rehabilitation of structures due to penetrability and convenience of application. Grouts for repair applications typically require high-performance properties such as rapid strength development and superior shrinkage characteristics. Sometimes industrial by-products referred as supplementary cementitious materials (SCM) are used with neat cement due to their capabilities to provide binding properties at delayed stage. Micro silica, fly ash and metakaolin are such SCMs, those can modify and improve properties of cement products. This study aims at investigating long-term mass loss and linear shrinkage along with long-term compressive and flexural strength for grouts produced from ultrafine cement and SCMs. A series of mixtures were formulated to observe the effect of SCMs on these grout properties. Properties were determined after 365 days of curing at 23oC and 55% relative humidity. The effect of SCMs on the properties are characterised by statistical models. Response surfaces were constructed to quantify these properties in relation to SCMs replacement. The results suggested that shrinkage was reduced by metakaolin, while micro silica and fly ash had positive effects on compressive and flexural strength, respectively.

scholarly journals Kajian Karakteristik Beton Memadat Sendiri yang Menggunakan Serat Ijuk (Hal. 54-65)

2018 ◽  
Vol 4 (4) ◽  
pp. 54
Author(s):  
Iis Nurjamilah ◽  
Abinhot Sihotang
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Flexural Strength ◽  
Coarse Aggregate ◽  
Fresh Concrete ◽  
High Strength ◽  
Self Compacting Concrete ◽  
Palm Fiber ◽  
Fiber Concrete ◽  
Dilute Mixture

ABSTRAKKajian karakteristik beton memadat sendiri yang menggunakan serat ijuk merupakan sebuah kajian yang dilakukan untuk mengetahui pengaruh penambahan serat ijuk terhadap karakteristik beton memadat sendiri (SCC). Beton memadat sendiri yang menggunakan serat ijuk (PFSCC) didesain memiliki campuran yang encer, bermutu tinggi (= 40 MPa) dan memiliki persentase kekuatan lentur yang lebih baik. PFSCC  didapatkan dari hasil pencampuran antara semen sebanyak 85%, fly ash 15%, superplastizicer 1,5%, serat ijuk 0%, 0,5%; 1%; 1,5%; 2% dan 3% dari berat binder (semen + fly ash), kadar air 190 kg/m3, agregat kasar 552,47 kg/m3 dan pasir 1.063 kg/m3. Semakin banyak persentase penambahan serat ijuk ke dalam campuran berdampak terhadap menurunnya workability beton segar. Penambahan serat ijuk yang paling baik adalah sebanyak 1%, penambahan tersebut dapat meningkatkan kekuatan tekan beton sebesar 13% dan lentur sebesar 1,8%.Kata kunci: beton memadat sendiri (SCC), beton berserat, beton memadat sendiri yang menggunakan serat ijuk (PFSCC), serat ijuk ABSTRACTThe study of characteristics self compacting concrete using palm fibers is a study conducted to determine the effect of adding palm fibers to characteristics of self compacting concrete (SCC). palm fibers self compacting concrete (PFSCC) is designed to have a dilute mixture, high strength (= 40 MPa), and have better precentage flexural strength. PFSCC was obtained from mixing of 85% cement, 15% fly ash, 1.5% superplastizicer, 0%, 0.5%, 1%, 1.5%, 2% and 3% palm fibers from the weight of binder  (cement + fly ash), water content 190 kg/m3, coarse aggregate 552.47 kg/m3 and sand 1,063 kg/m3. The more persentage palm fibers content added to the mixture makes workability of fresh concrete decreases. The best addition of palm fiber is 1%, this addition can increases the compressive strength 13% and flexural strength 1.8%.Keywords: self compacting concrete (SCC), fiber concrete, Palm fiber self compacting concrete (PFSCC), palm fiber

Sign in / Sign up

Export Citation Format

Share Document