scholarly journals The electrical and mechanical properties of Cadmium chloride reinforced PVA:PVP blend films

2020 ◽  
Vol 12 ◽  
pp. 120006
Author(s):  
Rana S. Mahmood ◽  
Sabah A. Salman ◽  
Nabeel Ali Bakr
Keyword(s):  
Mechanical Properties ◽  
Electrical Conductivity ◽  
Polymer Blend ◽  
Weight Ratio ◽  
Experimental Results ◽  
Casting Method ◽  
Ac Electrical Conductivity ◽  
Elongation At Break ◽  
Blend Films ◽  
Reinforced Polymer

In this study, pure polymer blend (PVA:PVP) film and salt (CdCl2·H2O) reinforced polymer blend films were prepared at different weight ratios (10 wt%, 20 wt%, 40 wt%) using the casting method. The effect of the salt weight ratio on the dielectric properties of the polymer blend films reinforced by CdCl2·H2O salt were investigated, and the experimental results showed that the dielectric constant and the dielectric loss factor decreased as the frequency increased for all polymer blend films. Moreover, the above-mentioned properties increased with increasing salt weight ratios at the same frequency. The experimental results also showed an increase in AC electrical conductivity with increasing frequency, for all polymer blend films, and the AC electrical conductivity also increased with an increase in the weight ratio of the salt at the same frequency. The effect of the salt weight ratio on the mechanical properties of the salt-reinforced PVA:PVP polymer blend films was also studied. The experimental results obtained from the tensile test of the salt-reinforced polymer blend films show significant change in the values of tensile strength, elongation at break, and Young’s modulus with increasing salt weight ratios; the hardness value first increases then decreases with increasing salt weight ratios, and the fracture energy value increases with increasing salt weight ratios, thus they could be good candidates for hard adhesives with low flexibility.

scholarly journals Preparation and Characterization of HPMC/PVP Blend Films Plasticized with Sorbitol

2013 ◽  
Vol 2013 ◽  
pp. 1-7 ◽  
Author(s):  
H. Somashekarappa ◽  
Y. Prakash ◽  
K. Hemalatha ◽  
T. Demappa ◽  
R. Somashekar
Keyword(s):  
Mechanical Properties ◽  
Hydroxypropyl Methylcellulose ◽  
Solution Casting ◽  
Casting Method ◽  
Elongation At Break ◽  
X Ray ◽  
Blend Films ◽  
X Ray Scattering ◽  
Solution Casting Method

The aim of this present work is to investigate the effect of plasticizers like Sorbitol on microstructural and mechanical properties of hydroxypropyl methylcellulose (HPMC) and Polyvinylpyrrolidone (PVP) blend films. The pure blend and plasticized blend films were prepared by solution casting method and investigated using wide angle X-ray scattering (WAXS) method. WAXS analysis confirms that the plasticizers can enter into macromolecular blend structure and destroy the crystallinity of the films. FTIR spectra show that there are a shift and decrease in the intensity of the peaks confirming the interaction of plasticizer with the blend. Mechanical properties like tensile strength and Young’s Modulus decrease up to 0.6% of Sorbitol content in the films. Percentage of elongation at break increases suggesting that the plasticized films are more flexible than pure blend films. These films are suitable to be used as environmental friendly and biodegradable packaging films.

scholarly journals Fabrication and Characterization of Electrospun Polycaprolactone Blended with Chitosan-Gelatin Complex Nanofibrous Mats

2014 ◽  
Vol 2014 ◽  
pp. 1-7 ◽  
Author(s):  
Yongfang Qian ◽  
Zhen Zhang ◽  
Laijiu Zheng ◽  
Ruoyuan Song ◽  
Yuping Zhao
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Weight Ratio ◽  
Degree Of Crystallinity ◽  
X Ray Diffraction ◽  
Tissue Engineering Scaffolds ◽  
Elongation At Break ◽  
Nanofibrous Scaffolds ◽  
Two Peaks

Design and fabrication of nanofibrous scaffolds should mimic the native extracellular matrix. This study is aimed at investigating electrospinning of polycaprolactone (PCL) blended with chitosan-gelatin complex. The morphologies were observed from scanning electron microscope. As-spun blended mats had thinner fibers than pure PCL. X-ray diffraction was used to analyze the degree of crystallinity. The intensity at two peaks at 2θof 21° and 23.5° gradually decreased with the percentage of chitosan-gelatin complex increasing. Moreover, incorporation of the complex could obviously improve the hydrophilicity of as-spun blended mats. Mechanical properties of as-spun nanofibrous mats were also tested. The elongation at break of fibrous mats increased with the PCL content increasing and the ultimate tensile strength varied with different weight ratios. The as-spun mats had higher tensile strength when the weight ratio of PCL to CS-Gel was 75/25 compared to pure PCL. Both as-spun PCL scaffolds and PCL/CS-Gel scaffolds supported the proliferation of porcine iliac endothelial cells, and PCL/CS-Gel had better cell viability than pure PCL. Therefore, electrospun PCL/Chitosan-gelatin nanofibrous mats with weight ratio of 75/25 have better hydrophilicity mechanical properties, and cell proliferation and thus would be a promising candidate for tissue engineering scaffolds.

scholarly journals Structural, Thermal, Optical Characterizations of PANI/PMMA Composite Doped by TiO2 as an Application in Optoelectronic Devices

2021 ◽  
Author(s):  
Q. A. Alsulami ◽  
A. A. Rajeh
Keyword(s):  
Thin Films ◽  
Polymer Blend ◽  
Crystal Size ◽  
Casting Method ◽  
Third Order ◽  
Blend Films ◽  
High Efficient ◽  
Amorphous Nature ◽  
Reflectance Coefficient ◽  
Vibrational Bands

Abstract The casting method was employed for the preparation of polymer blend films doped with TiO2 (0.5, 1, 1.5, and 2.3 wt.%). The XRD outcomes show that TiO2 phase formation is anatase, with an average crystal size of 20.25 nm. PANI/PMMA-TiO2 nanocomposites samples have an amorphous nature. In addition, the degree of amorphousity is increased with the increase of the content of the TiO2 NPs. The FTIR method was employed for presenting the vibrational bands of the nanocomposites and the intermolecular bonding of the blend with the TiO2 NPs. The applied investigation involved the optical constant like absorption as well as t90-etransmission spectra, refractive index, reflectance, coefficient extinction, dielectric constant’ imaginary and real parts, the susceptibility (χ3) of third order and the optical band gaps. The optical band gap (Eg) values of the films of fabricated nanocomposites was lower upon doping (≤ 1.5 wt.%). The reduction of the value happened due to the introduction of the preselected TiO2 NPs into thin films. Such values significantly match the values which were revealed by the Tauc technique. It was proved through DSC and TGA techniques that TiO2 NPs can lead to the enhancement of the polymer blend in terms of thermal stability. As displayed by the DSC analysis, there is a single Tg of the polymer blend (PANI/PMMA), which prove their miscibility. The optical constants displayed by the experimental results show noticeable changes upon raising the doping concentrations. The resultant doped thin films indicate that the fabricating high-efficient optoelectronic machines are greatly promising.

Preparation and Characterization of Starch/PVA Blend for Biodegradable Packaging Material

2010 ◽  
Vol 123-125 ◽  
pp. 351-354 ◽  
Author(s):  
Fahmida Parvin ◽  
Md. Arifur Rahman ◽  
Jahid M.M. Islam ◽  
Mubarak A. Khan ◽  
A.H.M. Saadat
Keyword(s):  
Mechanical Properties ◽  
Packaging Material ◽  
Rice Starch ◽  
Packaging Materials ◽  
Casting Method ◽  
Environment Friendly ◽  
Elongation At Break ◽  
Biodegradable Packaging ◽  
Soil And Water

Polymer films of rice starch/Polyvinyl alcohol (PVA) were prepared by casting method. Different blends were made varying the concentration of rice starch and PVA. Tensile strength (TS) and elongation at break (Eb) of the prepared films were studied. Films made up of rice starch and PVA with a ratio of 2:8 showed highest TS. 10% sugar was added with highest TS giving four composition of Starch/PVA blend in order to increase TS and Eb. Films made up of rice starch and PVA and sugar with a ratio of 1:8:1 showed highest TS and Eb and the recorded value was 14.96MPa and 637% respectively. The physico-mechanical properties of the prepared sugar incorporated films were improved by grafting with acrylic monomer with the aid of UV radiation. A formulation was prepared with monomer, methylmethacrylat in methanol, and a photo initiator. The highest TS of the grafted films were recorded and the value was 16.38 MPa. The water uptake and weight loss in both soil and water of the grafted films are lower than the non-grafted films. The prepared films were further characterized with stereo micrograph and XRD. Finally, the produced film can be used as biodegradable packaging materials for shopping and garbage bags that are very popular and environment friendly.

scholarly journals Fabrication of Silk Fibroin/Graphene Film with High Electrical Conductivity and Humidity Sensitivity

Polymers ◽  
2019 ◽  
Vol 11 (11) ◽  
pp. 1774 ◽  
Author(s):  
Haoran Zhang ◽  
Juntao Zhao ◽  
Tieling Xing ◽  
Shenzhou Lu ◽  
Guoqiang Chen
Keyword(s):  
Mechanical Properties ◽  
Electrical Conductivity ◽  
Silk Fibroin ◽  
Biomedical Applications ◽  
Wearable Sensors ◽  
Graphene Film ◽  
Natural Material ◽  
Casting Method ◽  
Good Biocompatibility ◽  
Minimum Resistance

Silk fibroin (SF) is a natural material with good biocompatibility and excellent mechanical properties, which are complementary to graphene with ultrahigh electrical conductivity. In this study, to maximally combine graphene and silk fibroin, a well-dispersed silk fibroin/graphene suspension was successfully prepared in a simple and effective way. Then we prepared a flexible conductive SF/graphene film with a minimum resistance of 72.1 ± 4.7 Ω/sq by the casting method. It was found that the electrical conductivity of the SF/graphene film was related to the water content of the film, and the variation was more than 200 times. Therefore, it will play an important role in the field of humidity sensors. It also has excellent mechanical properties in both wet and dry states. These unique features make this material a promising future in the fields of biomedical applications, wearable sensors, and implantable internal sensors.

Correlation between Curing Temperature and the Properties of Conductive Composites

2013 ◽  
Vol 750-752 ◽  
pp. 119-122 ◽  
Author(s):  
Xiao Ya Wang ◽  
Zhi Dong Xia ◽  
Zhe Li
Keyword(s):  
Mechanical Properties ◽  
Electrical Conductivity ◽  
Crosslink Density ◽  
Fracture Morphology ◽  
Curing Temperature ◽  
Tensile Fracture ◽  
Elongation At Break ◽  
Conductive Composites ◽  
The Stability ◽  
Better Than

This study was carried out to discuss the influence of curing temperature on the performance of conductive composites filled with nickel-coated graphite (NCG). The electrical conductivity, crosslink density, mechanical properties and tensile fracture morphology have been investigated. The results indicated that curing temperature had great impact on the electrical conductivity and mechanical properties. Voluem resistivity decreased from 43.1 to 0.08 ohm-cm at 125°C-205°C, and the reason was discussed in light of formation and break of the conductive network in the composites. The stability of SR-NCG cured at 165°C-205°C were also better than those cured at other curing temperature. Besides, tensile strength increased from 2.41 to 7.19Mpa at 125°C-225°C, elongation at break have a 56% increase, and Shore A hardness also incresed from 74 to 82.

scholarly journals Experimental Investigation of Fatigue Debonding Growth in FRP–Concrete Interface

Materials ◽  
2020 ◽  
Vol 13 (6) ◽  
pp. 1459 ◽  
Author(s):  
Xinzhe Min ◽  
Jiwen Zhang ◽  
Chao Wang ◽  
Shoutan Song ◽  
Dong Yang
Keyword(s):  
Growth Rate ◽  
Weight Ratio ◽  
High Strength ◽  
Load Level ◽  
Experimental Results ◽  
Fatigue Load ◽  
Load Range ◽  
Pull Out ◽  
Reinforced Polymer ◽  
Externally Bonded

An externally bonded fiber reinforced polymer (FRP) plate (or sheet) is now widely used in strengthening bending members due to its outstanding properties, such as a high strength to weight ratio, easy operating, corrosion and fatigue resistance. However, the concrete member strengthened by this technology may have a problem with the adhesion between FRP and concrete. This kind of debonding failure can be broadly classified into two modes: (a) plate end debonding at or near the plate end, and (b) intermediate crack-induced debonding (intermediate crack-induced (IC) debonding) near the loading point. The IC debonding, unlike the plate end debonding, still needs a large amount of investigation work, especially for the interface under fatigue load. In this paper, ten single shear pull-out tests were carried out under a static or fatigue load. Different load ranges and load levels were considered, and the debonding growth process was carefully recorded. The experimental results indicate that the load range is one of the main parameters, which determines the debonding growth rate. Moreover, the load level can also play an important role when loaded with the same load range. Finally, a new prediction model of the fatigue debonding growth rate was proposed, and has an excellent agreement with the experimental results.

scholarly journals FTIR spectroscopy characterization and critical comparison of poly(vinyl)alcohol and natural hydroxyapatite derived from fish bone composite for bone-scaffold

2021 ◽  
Vol 2120 (1) ◽  
pp. 012004
Author(s):  
May Teng Hooi ◽  
Siew Wei Phang ◽  
Hui Ying Yow ◽  
Edmund David ◽  
Ning Xin Kim ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Vinyl Alcohol ◽  
Fish Bone ◽  
Poly Vinyl Alcohol ◽  
Solution Casting ◽  
Casting Method ◽  
Elongation At Break ◽  
Solution Casting Method ◽  
Extrusion Method

Abstract This paper presents the interaction comparison of poly(vinyl) alcohol (PVA) with hydroxyapatite derived from Spanish Mackerel (SM) and Whitefin Wolf Herring (WWH) bones, in different processing method. PVA filament and solution casting method illustrated higher crystallinity in the FTIR graph as compared to the PVA pellet and filament extrusion method. Besides, minimal interactions between PVA with glycerol and HAp was observed as well. PVA pellet and solution casting method portrait higher interaction as compared to the PVA filament and extrusion method. As for the HAp of SM and WWH, WWH had higher crystallinity and better cell adhesion with a higher Ca/P ratio while SM had relatively better mechanical strength with Ca/P ratio near to stoichiometric value. The loading of HAp (0, 2.5, 5, 10, 20, 30%) does not affect interactions of PVA/HAp composite in FTIR, and thermal properties in TGA. However, it caused an increase in crystallinity at low HAp loading and decreased at higher loading of HAp above 10%. Upon addition of HAp, tensile strength increased and elongation at break decreased. As the loading of HAp increased, both mechanical properties decreased. Scaffold with WWH composite possessed lower tensile strength and higher elongation at break than SM composite. The result of mechanical properties corresponded to the SEM result. ANOVA analysis justified the effect of HAp variations and loading on the mechanical properties of the composite was prominent.

scholarly journals Mechanical Characterization of Rapid Solidified Alsicumg Alloys by New CRSS Casting Method Under T6 Condition

2019 ◽  
Vol 8 (12) ◽  
pp. 2897-2902
Keyword(s):  
Mechanical Properties ◽  
Manufacturing Process ◽  
High Performance ◽  
Weight Ratio ◽  
Solidification Process ◽  
Casting Process ◽  
Casting Method ◽  
Silicon Alloys ◽  
Hardness Tester

Aluminum-silicon alloys acquiring extensive industrial attention due to their superior resistance to rate of wear and elevated strength to weight ratio properties. Though the properties of the materials substantially depend on the manufacturing process they involve. Thus many industries focusing on new manufacturing methods to produce high-performance alloys. In this present study, AlSi (16-18) alloys were prepared by new CRSS (combined rheo stir squeeze) casting method with rapid-solidification process under T-6 condition. CRSS-T6 as casting process enhances the microstructural and mechanical properties significantly by 40-70%. Whereas, the maximum value of hardness (179.37) was found with AlSi17Cu3.5Mg0.8 with CRSS-T6. The improvements in hardness and elastic properties were mainly ascribed to size, distribution, and morphology of Si-particles because of its manufacturing process. SEM, advanced metallurgical microstructure and EDS analysis techniques are used for the surface morphologies observation. Moreover, Brinell hardness tester and Tensometer are used for the characterization of mechanical properties

A Review on Mechanical Properties of Natural Fibre Reinforced PLA Composites

2021 ◽  
Vol 15 ◽  
Author(s):  
Agnivesh Kumar Sinha ◽  
Kasi Raja Rao ◽  
Vinay Kumar Soni ◽  
Rituraj Chandrakar ◽  
Hemant Kumar Sharma ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Polymer Composites ◽  
Biodegradable Polymer ◽  
Weight Ratio ◽  
Natural Fibre ◽  
Polymer Matrices ◽  
Poly Lactic Acid ◽  
Butylene Succinate ◽  
Reinforced Polymer ◽  
Fibre Reinforced Polymer

Presently, scientists and researchers are in an endless quest to develop green, recyclable, and eco-friendly materials. Natural fibre reinforced polymer composites became popular among materialists due to their lightweight, high strength-to-weight ratio, and biodegradability. However, all-natural fibre reinforced polymer composites are not biodegradable. Polymer matrices like poly-lactic acid (PLA) and poly-butylene succinate (PBS) are biodegradable, whereas epoxy, polypropylene, and polystyrene are non-biodegradable polymer matrices. Besides biodegradability, PLA has been known for its excellent physical and mechanical properties. This review emphasises the mechanical properties (tensile, flexural, and impact strengths) of natural fibrereinforced PLA composites. Factors affecting the mechanical properties of PLA composites are also discussed. It also unveils research gaps from the previous literature, which shows that limited studies are reported based on modeling and prediction of mechanical properties of hybrid PLA composites reinforcing natural fibres like abaca, aloe vera, and bamboo fibres.

Sign in / Sign up

Export Citation Format

Share Document