scholarly journals INVESTIGATION ON VOLUME VARIATION FOR ALPHA STIRLING ENGINES ON ISOTHERMAL MODEL

2020 ◽  
Vol 19 (2) ◽  
pp. 10
Author(s):  
M. K. Gussoli ◽  
J. C. D. de Oliveira ◽  
M. Higa

The usage of renewable energies is approximately 11% of the matrix energy worldwide. In countries known for its renewable sources, such as Brazil, the percentage is close to 38%. The importance to study Stirling engines and propose a prototype is that they are a feasible alternative for generation of power and electricity when considering low quality sources such as solar and waste energy. This paper will compare two different approaches of the volume variation, sinusoidal and kinematic, using an isothermal model that represents the Stirling engines. The comparison is made for an a type engine. Such approaches are capable of representing an estimative of work and power output for Stirling engines since the difference of results for these approaches are 8.07% for power output. As both approaches are a valid choice for analyzing the Stirling engine cycle, the availability of the data determines which approach is the most suitable for characterizing the engine performance.

Author(s):  
E. D. Rogdakis ◽  
I. P. Koronaki ◽  
G. D. Antonakos

The Stirling engine, as an external combustion engine, can be powered using a variety of heat sources including the continuous combustion process thus achieving significantly reduced emissions. Energy systems powered by a Stirling engines meet the needs of various applications not only in the domestic and industrial sections but in military and space gadgets as well. Stirling engines can also be used as cryocoolers in medical applications where they are called to achieve very low temperatures. Each energy system using Stirling Engine optimizes its performance in specific operating conditions. The system capacity depends on the geometric and structural characteristics, the design of the unit, the environment in which the engine is allowed to it works as well as the size of the load. In order to study the function and the efficiency of Stirling energy systems a CHP SOLO 161V -ALPHA TYPE STIRLING ENGINE was installed in the Laboratory of Applied Thermodynamics of NTUA. A thermodynamic analysis has been conducted using appropriate computing codes. The effect of each independent variable on the system performance was investigated. The study was divided into distinct levels of detail, bringing out each variable. Initially, the performance of the heat engine was examined assuming an ideal regenerator. Then, the effectiveness of the regenerator was evaluated as well as its effect on the engine performance, while the effect of the pressure drop and the energy dissipation on the engine efficiency was also investigated. Measurements were conducted using different operational conditions concerning the heating load of the engine. The effect of the geometrical characteristics of the regenerator on power output and engine performance was examined based on the results of a simulation analysis. Moreover, the power output and the efficiency of the machine in relation to the thermal load of the unit and the average pressure of the working medium were investigated. Major performance input characters affecting geometrical and operational parameters of the unit were identified leading to unit optimization with specific combinations leading to increased system performance. Simulation results were validated by comparison to corresponding values obtained by relative experiments conducted with the SOLO unit. Finally, a sensitivity analysis was performed in order to investigate the effect of the operating conditions on the performance of an alpha type Stirling Engine.


2012 ◽  
Vol 2012 ◽  
pp. 1-14 ◽  
Author(s):  
A. Asnaghi ◽  
S. M. Ladjevardi ◽  
P. Saleh Izadkhast ◽  
A. H. Kashani

This paper provides numerical simulation and thermodynamic analysis of SOLO 161 Solar Stirling engine. Some imperfect working conditions, pistons' dead volumes, and work losses are considered in the simulation process. Considering an imperfect regeneration, an isothermal model is developed to calculate heat transfer. Hot and cold pistons dead volumes are accounted in the work diagram calculations. Regenerator effectiveness, heater and cooler temperatures, working gas, phase difference, average engine pressure, and dead volumes are considered as effective parameters. By variations in the effective parameters, Stirling engine performance is estimated. Results of this study indicate that the increase in the heater and cooler temperature difference and the decrease in the dead volumes will lead to an increase in thermal efficiency. Moreover, net work has its maximum value when the angle between two pistons shaft equal to 90 degrees while efficiency is maximum in 110 degrees.


Author(s):  
R.A. Herring

Rapid thermal annealing (RTA) of ion-implanted Si is important for device fabrication. The defect structures of 2.5, 4.0, and 6.0 MeV As-implanted silicon irradiated to fluences of 2E14, 4E14, and 6E14, respectively, have been analyzed by electron diffraction both before and after RTA at 1100°C for 10 seconds. At such high fluences and energies the implanted As ions change the Si from crystalline to amorphous. Three distinct amorphous regions emerge due to the three implantation energies used (Fig. 1). The amorphous regions are separated from each other by crystalline Si (marked L1, L2, and L3 in Fig. 1) which contains a high concentration of small defect clusters. The small defect clusters were similar to what had been determined earlier as being amorphous zones since their contrast was principally of the structure-factor type that arises due to the difference in extinction distance between the matrix and damage regions.


Author(s):  
P B Parejiya ◽  
B S Barot ◽  
P K Shelat

The present study was carried out to fabricate a prolonged design for tramadol using Kollidon SR (Polyvinyl acetate and povidone based matrix retarding polymer). Matrix tablet formulations were prepared by direct compression of Kollidon SR of a varying proportion with a fixed percentage of tramadol. Tablets containing a 1:0.5 (Drug: Kollidon SR) ratio exhibited a rapid rate of drug release with an initial burst effect. Incorporation of more Kollidon SR in the matrix tablet extended the release of drug with subsequent minimization of the burst effect as confirmed by the mean dissolution time, dissolution efficiency and f2 value. Among the formulation batches, a direct relationship was obtained between release rate and the percentage of Kollidon SR used. The formulation showed close resemblance to the commercial product Contramal and compliance with USP specification. The results were explored and explained by the difference of micromeritic characteristics of the polymers and blend of drug with excipients. Insignificant effects of various factors, e.g. pH of dissolution media, ionic strength, speed of paddle were found on the drug release from Kollidon-SR matrix. The formulation followed the Higuchi kinetic model of drug release. Stability study data indicated stable character of Batch T6 after short-term stability study.


2018 ◽  
Vol 146 (12) ◽  
pp. 3949-3976 ◽  
Author(s):  
Herschel L. Mitchell ◽  
P. L. Houtekamer ◽  
Sylvain Heilliette

Abstract A column EnKF, based on the Canadian global EnKF and using the RTTOV radiative transfer (RT) model, is employed to investigate issues relating to the EnKF assimilation of Advanced Microwave Sounding Unit-A (AMSU-A) radiance measurements. Experiments are performed with large and small ensembles, with and without localization. Three different descriptions of background temperature error are considered: 1) using analytical vertical modes and hypothetical spectra, 2) using the vertical modes and spectrum of a covariance matrix obtained from the global EnKF after 2 weeks of cycling, and 3) using the vertical modes and spectrum of the static background error covariance matrix employed to initiate a global data assimilation cycle. It is found that the EnKF performs well in some of the experiments with background error description 1, and yields modest error reductions with background error description 3. However, the EnKF is virtually unable to reduce the background error (even when using a large ensemble) with background error description 2. To analyze these results, the different background error descriptions are viewed through the prism of the RT model by comparing the trace of the matrix , where is the RT model and is the background error covariance matrix. Indeed, this comparison is found to explain the difference in the results obtained, which relates to the degree to which deep modes are, or are not, present in the different background error covariances. The results suggest that, after 2 weeks of cycling, the global EnKF has virtually eliminated all background error structures that can be “seen” by the AMSU-A radiances.


1894 ◽  
Vol 1 (11) ◽  
pp. 496-499
Author(s):  
Henry H. Howorth

Mr. Deeley tells your readers that he has recently been to the summit of Mont Blanc, and has been studying the difference between névé and glacier ice. This is interesting; but we thought that a great many people had done the same thing during the last hundred years, and we thought that one of them, Forbes, had studied the famous Mountain and the phenomenoninquestion to good effect, not in a casual visit to the Alps, but in the course of many years of patient labour. Among other things we also thought he had shown that in a viscous body like ice, the slope of the upper surface necessary to make it begin to move is the same as the slope which, would be required to induce motion in the ice if its bed were inclined at an angle. He further collected considerable evidence to show what the least angle is upon which ice will begin to move. This is the slope, the least slope, available. It is nothing less than astounding to me that anyone should venture to postulate a Scand in avian ice-sheet in the North Sea until he had considered this necessary factor, and how it would operate.The Scand in avian ice-sheet was, I believe, the invention of Croll, who, sittinginhis arm-chair and endowed with a brilliant imagination, imposed upon sober science this extraordinary postulate. He did not dream of testing it by an examination of the coasts of Norway, or even of Britain, but put it forward apparently as a magnificent deduction. All deductions untested by experiment are dangerous. Thus it came about that the great monster which is said to have come from Norway, goodness knows by what mechanical process, speedily dissolved away on the application of inductive methods. Of course it still maintained its hold upon that section, of geologists who dogmatiseinprint a great deal about the Glacial period before they have ever seen a glacier at work at all; but I am speaking of those who have studied the problem inductively. First Mr. James Geikie, a disciple of Croll, was obliged to confess that this ice-sheet, which is actually said to have advanced as far as the hundred-fathom line in the Atlantic, and there presented a cliff of ice like the Antarctic continent, never can have reached the Faroes, which had an ice-sheet of their own. Next Messrs. Peach and Home were constrained to admit that no traces of it of any kind occur in the Orkneys, or in Eastern Scotland. They still maintained its presence in the Shetlands; however, this was upon evidence which is somewhat extraordinary. I do not mean the evidence as to the direction of the striation, which was so roughly handled by Mr. Milne-Home, but I mean the evidence they adduce that the boulders found on the islands are apparently all local ones, and that, contrary to the deposits of glaciers, they diminish in number as we recede from the matrix whence they were derived.


Telematika ◽  
2020 ◽  
Vol 17 (1) ◽  
pp. 26
Author(s):  
Afif Irfan Abdurrahman ◽  
Bambang Yuwono ◽  
Yuli Fauziah

Flood disaster is a dangerous disaster, an event that occurs due to overflow of water resulting in submerged land is called a flood disaster. Almost every year Bantul Regency is affected by floods due to high rainfall. The flood disaster that struck in Bantul Regency made the Bantul District Disaster Management Agency (BPBD) difficult to handle so that it needed a mapping of the level of the impact of the flood disaster to minimize the occurrence of floods and provide information to the public.This study will create a system to map the level of impact of floods in Bantul Regency with a decision support method namely Multi Attribute Utility Theory (MAUT). The MAUT method stage in determining the level of impact of flood disasters through the process of normalization and matrix multiplication. The method helps in determining the areas affected by floods, by managing the Indonesian Disaster Information Data (DIBI). The data managed is data on criteria for the death toll, lost victims, damage to houses, damage to public facilities, and damage to roads. Each criteria data has a value that can be used to determine the level of impact of a flood disaster. The stages for determining the level of impact of a disaster require a weighting calculation process. The results of the weighting process display the scoring value which has a value of 1 = low, 2 = moderate, 3 = high. To assist in determining the affected areas using the matrix normalization and multiplication process the process is the application of the Multi Attribute Utility Theory (MAUT) method.This study resulted in a mapping of the level of impact displayed on google maps. The map view shows the affected area points and the level of impact of the flood disaster in Bantul Regency. The mapping produced from the DIBI data in 2017 produced the highest affected area in the Imogiri sub-district. The results of testing the data can be concluded that the results of this study have an accuracy rate of 95% when compared with the results of the mapping previously carried out by BPBD Bantul Regency. The difference in the level of accuracy is because the criteria data used are not the same as the criteria data used by BPBD in Bantul Regency so that the accuracy rate is 95%.


2021 ◽  
Vol 6 (2) ◽  
pp. 50-55
Author(s):  
Wildan Sofary Darga ◽  
Edy K. Alimin ◽  
Endah Yuniarti

Exhaust Gas Temperatue is an parameter where the hot gases’s temperature leave the gas turbine. Exhaust gas temperature margin is the difference between highest temperature at take off phase with redline on indicator (???????????? ???????????????????????? °????=???????????? ????????????????????????????−???????????? ???????????????? ????????????). EGTM is one of any factor to determine engine performance. A good perfomance of an engine when it has a big margin (EGTM), during operation of an engine the EGTM could decrease untill 0 (zero). So many factors could affect EGTM deteroration there are: distress hardware such as airfoil erosion, leak of an airseals, and increase of clearance between tip balde and shroud. Increase of clearance happens in high pressure compressor rotor clearance. In CFM56-7 have 9 stage(s) of high pressure compressor and each stage give the EGT Loses. The calculation of EGT Effect/Losses is actual celarance – minimum clearance x 1000 x EGT Effect °C, where actual clearance define by the substraction of outside diameter’s rotor with inside diameter’s shroud, minimum clearance define in the manual, 1000 is adjustment from mils/microinch to inch, and EGT Effect is temperature that define in the manual. The analysist had done with 6 (six) engine serial number and proceed by corelation that shown linkage between clearance and EGT Effect, the corelation is strong shown the result of corelation (r) is 0.994275999 or nearest 1.


Author(s):  
T. A. Akhmetov ◽  
V. K. Merinov ◽  
N. V. Kargapolova

The possibility of using the deposited suspended particles of electric arc furnaces as heat-resistant modifying additives for friction composites is considered. It is shown that the precipitated particles obtained during the smelting of steel of different grades have identical morphology and are a homogeneous mechanical mixture consisting mainly of spherical particles of no more than 1 µm in size.It is established that the composites on the basis of the fluoropolymer, modified by precipitated particles obtained in the smelting of steel of various sizes have different tribological properties. This is due to the difference in the chemical composition of the deposited particles.It was found that the use of deposited particles in composite materials allows to vary the value of the dynamic friction coefficient in a wider range, in particular to obtain higher and stable values, while the wear resistance of modified friction composites is more than 500 times higher than the same index of the matrix polymer – polytetrafluoroethylene.


Author(s):  
I.V. Frolov ◽  
◽  
V.A. Sergeev ◽  
A.M. Hodakov ◽  
S.A. Zaytsev ◽  
...  

The paper presents the results of studies of changes in the characteristics of LED COB matrices of the GW P9LR31.EM - DURIS S 8 type as part of a LED luminaire when tested under the direct current in a continuous mode and in an electrocycling mode. The arrays consist of eight InGaN/GaN LED dies connected in series, coated with a phosphor. Calculation in the Comsol Multiphtsics environment of the temperature field of the luminaire at the rated operating current and free convection heat transfer showed that the maximum overheating of the matrices does not exceed 46 K, and the difference in their temperatures is 2 K. At the same time, the experimental values of the thermal resistances of the matrices of a real lamp vary from 42 to 58 K/W. Before testing, the I-V characteristics of the matrices differ markedly in the level of leakage current in the voltage range from 14 V to 19 V, and the LEDs in the luminaire matrices have a significant spread in the brightness of emission in the microcurrent mode. The degree of this scatter within each matrix was estimated by measuring the luminescence brightness of each die of the matrix and calculating the coefficient of variation γ. It was found that the coefficient of variation of the emission brightness of the COB matrix dies measured at a current of 100 nA strongly correlates with the leakage current. When testing a luminaire under the direct current, the most significant changes in the electrophysical and optical characteristics of COB matrices are observed in the range of microcurrents: the distribution of the emission brightness of the matrix dies at a current of 100 nA becomes more uniform. The greatest changes in matrix characteristics were observed after the first 700 hours of testing, that is, at the running-in stage. At the same time, no correlation was found between the degree of change in the characteristics of the matrices during tests and their thermal resistances.


Sign in / Sign up

Export Citation Format

Share Document