scholarly journals Experimental Investigation on the Effect of Microwave Heating on Rock Cracking and Their Mechanical Properties

2021 ◽  
Author(s):  
Gaoming Lu ◽  
Jianjun Zhou
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Microwave Irradiation ◽  
Microwave Heating ◽  
Hard Rock ◽  
Irradiation Time ◽  
Poisson's Ratio ◽  
Rock Fracturing ◽  
Microwave Assisted ◽  
Rock Cracking

Due to various advantages including high efficiency, energy-saving, and having no secondary pollution (no dust or noise), the technology of microwave-induced fracturing of hard rock has been considered as a potential method for rock fracturing and breaking. Realizing microwave-assisted mechanical rock cutting using the microwave-induced hard rock fracturing technique can prolong the mechanical life and improve the efficiency of rock-breaking operations. For example, to realize microwave-assisted TBM excavation for hard rock tunnel. At present, this technology is still in the laboratory research stage. By summarizing the research results of relevant scholars in this field, this paper generalizes the mechanism of microwave heating of rock, microwave heating system, heating characteristics, and the effect of microwave heating on rock cracking and mechanical properties. Microwave heating causes microscopic cracks on the surface of the rock and microscopic cracks inside the rock. The higher the microwave power, the longer the irradiation time, the more serious the cracks propagation. Uniaxial compressive, Brazilian tensile, and point load strengths all decreased with increasing microwave irradiation time at rates that were positively related to the power level. The conventional triaxial compressive strength of basalt samples decreased linearly with microwave irradiation time, and the higher the confining pressure, the smaller the reduction in the strength of basalt samples after microwave treatment. In addition, the elastic modulus and Poisson’s ratio of basalts decreased in a quasi-linear manner with the growth of microwave irradiation time under uniaxial compression. While microwave irradiation has a slight influence on elastic modulus and Poisson’s ratio under triaxial compression. The cohesion decreases with increasing microwave irradiation time and shows an approximately linear decrease over time.

Measurement of Cement in Situ Stresses and Mechanical Properties Without Cooling or Depressurization

2021 ◽  
Author(s):  
Meng Meng ◽  
Luke Frash ◽  
James Carey ◽  
Wenfeng Li ◽  
Nathan Welch ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Mechanical Property ◽  
Elastic Modulus ◽  
Poisson’S Ratio ◽  
Axial Stress ◽  
Triaxial Compression ◽  
In Situ Measurement ◽  
Poisson's Ratio ◽  
Ambient Conditions

Abstract Accurate characterization of oilwell cement mechanical properties is a prerequisite for maintaining long-term wellbore integrity. The drawback of the most widely used technique is unable to measure the mechanical property under in situ curing environment. We developed a high pressure and high temperature vessel that can hydrate cement under downhole conditions and directly measure its elastic modulus and Poisson's ratio at any interested time point without cooling or depressurization. The equipment has been validated by using water and a reasonable bulk modulus of 2.37 GPa was captured. Neat Class G cement was hydrated in this equipment for seven days under axial stress of 40 MPa, and an in situ measurement in the elastic range shows elastic modulus of 37.3 GPa and Poisson's ratio of 0.15. After that, the specimen was taken out from the vessel, and setted up in the triaxial compression platform. Under a similar confining pressure condition, elastic modulus was 23.6 GPa and Possion's ratio was 0.26. We also measured the properties of cement with the same batch of the slurry but cured under ambient conditions. The elastic modulus was 1.63 GPa, and Poisson's ratio was 0.085. Therefore, we found that the curing condition is significant to cement mechanical property, and the traditional cooling or depressurization method could provide mechanical properties that were quite different (50% difference) from the in situ measurement.

Elasto-Plastic Hemispherical Contact Models for Various Mechanical Properties

2005 ◽  
Author(s):  
John J. Quicksall ◽  
Robert L. Jackson ◽  
Itzhak Green
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Material Properties ◽  
Poisson’S Ratio ◽  
Carbon Steels ◽  
Poisson's Ratio ◽  
Aluminum Bronze ◽  
Contact Models ◽  
Element Technique ◽  
Malleable Cast

This work uses the finite element technique to model the elasto-plastic deformation of a hemisphere contacting a rigid flat for various material properties typical of aluminum, bronze, copper, titanium and malleable cast iron. Additionally, this work conducted parametric FEM tests on a generic material in which the elastic modulus and Poisson’s ratio are varied independently while the yield strength is held constant. A larger spectrum of material properties are covered in this work than in most previous works. The results are compared to two previously formulated elasto-plastic models simulating the deformation of a hemisphere in contact with a rigid flat. Both of the previously formulated models use carbon steel mechanical properties to arrive at empirical formulations implied to pertain to various materials. While both models considered several carbon steels with varying yield strengths, they did not test materials with varying Poisson’s ratio or elastic modulus. The previously generated elasto-plastic models give fairly good predictions when compared to the FEM results for various material properties from the current work, except that one model produces more accurate predictions overall, especially at large deformations where other models neglect important trends due to decreases in “hardness” with increasing deformation.

Biomimetic composites inspired by venous leaf

2017 ◽  
Vol 52 (3) ◽  
pp. 361-372 ◽  
Author(s):  
Gongdai Liu ◽  
R Ghosh ◽  
A Vaziri ◽  
A Hossieni ◽  
D Mousanezhad ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Yield Stress ◽  
Poisson’S Ratio ◽  
Composite Structures ◽  
Volume Fraction ◽  
Matrix Material ◽  
Poisson's Ratio ◽  
Fiber Volume ◽  
Young’S Moduli

A typical plant leaf can be idealized as a composite having three principal fibers: the central mid-fiber corresponding to the mid-rib, straight parallel secondary fibers attached to the mid-fiber representing the secondary veins, and then another set of parallel fibers emanating from the secondary fibers mimicking the tertiary fibers embedded in a matrix material. This paper introduces a biomimetic composite design inspired by the morphology of venous leafs and investigates the effects of venation morphologies on the in-plane mechanical properties of the biomimetic composites using finite element method. The mechanical properties such as Young’s moduli, Poisson’s ratio, and yield stress under uniaxial loading of the resultant composite structures was studied and the effect of different fiber architectures on these properties was investigated. To this end, two broad types of architectures were used both having similar central main fiber but differing in either having only secondary fibers or additional tertiary fibers. The fiber and matrix volume fractions were kept constant and a comparative parametric study was carried out by varying the inclination of the secondary fibers. The results show that the elastic modulus of composite in the direction of main fiber increases linearly with increasing the angle of the secondary fibers. Furthermore, the elastic modulus is enhanced if the secondary fibers are closed, which mimics composites with closed cellular fibers. In contrast, the elastic modulus of composites normal to the main fiber ( x direction) exponentially decreases with the increase of the angle of the secondary fibers and it is little affected by having secondary fibers closed. Similar results were obtained for the yield stress of the composites. The results also indicate that Poisson’s ratio linearly increases with the secondary fiber angle. The results also show that for a constant fiber volume fraction, addition of various tertiary fibers may not significantly enhance the mechanical properties of the composites. The mechanical properties of the composites are mainly dominated by the secondary fibers. Finally, a simple model was proposed to predict these behaviors.

Meso-mechanics simulation analysis of microwave-assisted mineral liberation

2015 ◽  
Author(s):  
Qin Like ◽  
Dai Jun ◽  
Yuan Liqun
Keyword(s):  
Energy Consumption ◽  
Microwave Irradiation ◽  
Power Density ◽  
Microwave Power ◽  
Mineral Content ◽  
Crystal Size ◽  
Irradiation Time ◽  
Mineral Crystal ◽  
Microwave Assisted ◽  
Time And Energy

Microwave-assisted crushing and grinding can improve efficiency and reduce energy consumption. This paper takes rock grains with galena and calcite as the research object to establish a two-dimensional computational model through the finite difference software FLAC2D. It analyzes the process and law of mineral boundary failure under microwave irradiation, and assesses the effects of four factors, namely, microwave irradiation time, power density, mineral crystal size, and mineral content, on mineral boundary failure. Results indicate an optimal microwave irradiation period for the rapid failure of mineral boundary. Moreover, irradiation time and energy consumption can be reduced by increasing the microwave power density. However, irradiation time and energy consumption are basically unchanged when the microwave power density is above a certain threshold. Mineral content slightly affects the microwave irradiation time, whereas mineral crystal size significantly affects the microwave irradiation time. In addition, a larger-sized mineral crystal requires less irradiation time and energy consumption to reach the same failure rate. However, irradiation time and energy consumption slightly change when the crystal size is larger than a certain value.

Research on Mechanical Properties of C100 High-Strength Concrete Used for Frozen Shaft

2012 ◽  
Vol 598 ◽  
pp. 388-392
Author(s):  
Hong Qiang Chu ◽  
Lin Hua Jiang ◽  
Ning Xu ◽  
Chuan Sheng Xiong
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Fly Ash ◽  
High Strength Concrete ◽  
High Strength ◽  
Cementitious Materials ◽  
Poisson's Ratio ◽  
Strength Concrete ◽  
Tensile Elastic Modulus ◽  
Early Strength

The mechanical properties of C100 high-strength concrete used for frozen shaft were studied in this research. The results demonstrate that: The cementitious materials 570kg/m3 concrete 28 strength is only 104.5MPa, which is lower than the C100 requirements; the early strength (3d) of the concrete doped with 30% admixture is less than 20% admixture concrete, but with the age increase, its strength gradually reaches close to concrete doped with 20% admixture, and eventually exceeds the concrete doped with 20% admixture.The tension-compression of high strength concrete doped with 15% fly ash and 15% slag is the smallest, while the tension-compression of the concrete doped 10% fly ash and 10% slag reaches the maximum.The Poisson's ratio of C100 concrete is between 0.20 and 0.24; the compressive elastic modulus is about 50GPa; and the tensile elastic modulus is about 110GPa.

Experimental Study on the Influence of Temperature on Shale Mechanical Properties under Conventional Triaxial Compression

2011 ◽  
Vol 250-253 ◽  
pp. 1452-1455 ◽  
Author(s):  
Lu Bo Meng ◽  
Tian Bin Li ◽  
Liang Wen Jiang ◽  
Hong Min Ma
Keyword(s):  
Mechanical Properties ◽  
Thermal Stress ◽  
Elastic Modulus ◽  
High Temperature ◽  
Poisson’S Ratio ◽  
Triaxial Compression ◽  
Poisson's Ratio ◽  
Influence Of Temperature ◽  
Conventional Triaxial Compression ◽  
Influence Of Temperature On

High temperature conventional triaxial compression test of shale are carried out by the MTS815 servo-controlled testing machine, based on the experimental results, the relationships between temperature and shale peak strength, elastic modulus, Poisson's ratio, cohesion, internal friction angle are investigated. Although the experimental results are discrete comparatively, the general law is obvious. When the confining pressure imposed on shale is constant and the temperature changes form 25°C to 120°C, with the increasing of the temperature, the triaxial compression strength, shear strength gradually increase, while average elastic modulus, Poisson's ratio has a slightly decrease. The thermal stress generated by the high temperature plays a role to accommodate the deformation and the function of preventing crack propagation, thus the bearing capacity of shale samples are strengthened. But the influence of temperature on shale mechanical properties mutates when the temperature is at 80°C. Shale peak strength dramatically decreased, average elastic modulus decreased slightly, and Poisson's ratio also increased slightly, which indicated that at 80°C, different thermal expansivity of mineral particles of shale may cause cross-grain boundary thermal expansion incongruous, creating additional thermal stress, thus the sample’s bearing capacity decreased.

Efficient, microwave-assisted intramolecular 1,3-dipolar cycloadditions of oximes and N-methylnitrones derived from o-alkenylmethoxy-acetophenones

2005 ◽  
Vol 83 (3) ◽  
pp. 260-265 ◽  
Author(s):  
Surinderjit Singh ◽  
M PS Ishar ◽  
Gajendra Singh ◽  
Rajinder Singh
Keyword(s):  
Microwave Irradiation ◽  
Microwave Heating ◽  
Reaction Times ◽  
Solvent Free ◽  
Dipolar Cycloadditions ◽  
Microwave Assisted ◽  
Solvent Free Conditions ◽  
A Minor ◽  
Acetophenone Oxime

Contrary to literature reports, the o-allyloxy- and crotyloxy-acetophenone-oximes (2a, 2b) are transformed to nitrones, which undergo regio- and stereoselective intramolecular 1,3-dipolar cycloadditions, both on microwave heating under solvent free conditions and refluxing in toluene, to afford novel cycloadducts (5a, 5b); the oxazepine-N-oxide (3a) reported to be formed in 98% yield was obtained only as a minor product (~10%). However, o-cinnamyloxy-acetophenone-oxime (2c) under similar conditions undergoes intramolecular N-alkylation to afford nitrone (3c). The reactions carried out under microwave irradiation are cleaner, require shorter reaction times, and have higher yields. Corresponding intramolecular 1,3-dipolar cycloadditions of N-methylnitrones (B), generated in situ from o-alkenylmethoxy-acetophenones (1a–1c) and N-methylhydroxylamine under solvent-free microwave irradiation conditions, are completely regio- and stereoselective, require much shorter reaction times, and afford adducts (4a–4c) in higher yields, as compared with their thermal counterparts.Key words: cycloadditions, nitrones, oximes, o-alkenylmethoxy-acetophenones, microwave, isoxazolidines.

scholarly journals Elastic Mechanical Properties of 45S5-Based Bioactive Glass–Ceramic Scaffolds

Materials ◽  
2019 ◽  
Vol 12 (19) ◽  
pp. 3244 ◽  
Author(s):  
Francesco Baino ◽  
Elisa Fiume
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Elastic Modulus ◽  
Shear Modulus ◽  
Glass Ceramic ◽  
Poisson’S Ratio ◽  
Mechanical Performance ◽  
Poisson's Ratio ◽  
Shear Moduli ◽  
Bioactive Scaffolds

Porosity is recognized to play a key role in dictating the functional properties of bioactive scaffolds, especially the mechanical performance of the material. The mechanical suitability of brittle ceramic and glass scaffolds for bone tissue engineering applications is usually evaluated on the basis of the compressive strength alone, which is relatively easy to assess. This work aims to investigate the porosity dependence of the elastic properties of silicate scaffolds based on the 45S5 composition. Highly porous glass–ceramic foams were fabricated by the sponge replica method and their elastic modulus, shear modulus, and Poisson’s ratio were experimentally determined by the impulse excitation technique; furthermore, the failure strength was quantified by compressive tests. As the total fractional porosity increased from 0.52 to 0.86, the elastic and shear moduli decreased from 16.5 to 1.2 GPa and from 6.5 to 0.43 GPa, respectively; the compressive strength was also found to decrease from 3.4 to 0.58 MPa, whereas the Poisson’s ratio increased from 0.2692 to 0.3953. The porosity dependences of elastic modulus, shear modulus and compressive strength obeys power-law models, whereas the relationship between Poisson’s ratio and porosity can be described by a linear approximation. These relations can be useful to optimize the design and fabrication of porous biomaterials as well as to predict the mechanical properties of the scaffolds.

Mechanical Properties of Thin Film Silicon Carbide

2001 ◽  
Vol 687 ◽  
Author(s):  
Kamili M. Jackson ◽  
Richard L. Edwards ◽  
Guy F. Dirras ◽  
William N. Sharpe
Keyword(s):  
Mechanical Properties ◽  
Silicon Carbide ◽  
Elastic Modulus ◽  
Poisson’S Ratio ◽  
Poisson's Ratio ◽  
Massachusetts Institute Of Technology ◽  
Preliminary Results ◽  
High Temperature Electronics ◽  
Microtensile Testing ◽  
Institute Of Technology

AbstractSilicon carbide is a very attractive material for a variety of applications. Originally considered for use in high power and high temperature electronics because of its large bandgap, designers of MEMS are now considering use of silicon carbide because of its stability at high temperatures, resistance to corrosives, high stiffness, and radiation resistance. However, as with any new structural material, its mechanical properties must be measured for design information. This research measures the elastic modulus, strength, and Poisson's ratio of two different silicon carbides using microtensile testing. One material is a 0.5-1νm thick film from Case Western Reserve University. Preliminary results give an average of 420 GPa for elastic modulus, a strength of 1.2 GPa, and a Poisson's ratio of 0.19. The second material is from Massachusetts Institute of Technology with an average thickness of 30 microns. Preliminary results show an elastic modulus of 430 GPa, a strength of 0.49 GPa, and a Poisson's ratio of 0.24. In addition to the most recent results, techniques used to obtain these results, microstructure investigations, and a comparison of the materials are detailed.

Sign in / Sign up

Export Citation Format

Share Document