scholarly journals Pengaruh Variasi Polivinilpirolidon (PVP) Terhadap Pembentukan Serat Nano TiO2 Menggunakan Metode Electrospinning

2021 ◽  
Vol 2 (1) ◽  
pp. 11-16
Author(s):  
Vega Rahmawati Ar ◽  
◽  
Posman Manurung ◽  
Junaidi Junaidi ◽  
Pulung Karo Karo
Keyword(s):  
Crystal Structure ◽  
Fiber Diameter ◽  
Sol Gel ◽  
Xrd Analysis ◽  
Viscosity Measurement ◽  
Solution Viscosity ◽  
Nano Tio2 ◽  
Tio2 Nanofibers ◽  
Tio2 Nanofiber ◽  
Tem Characterization

Research on the formation of TiO2 nanofiber has been carried out with PVP variations of 1.1; 1,2; 1.3; 1.4 and 1.5 grams using electrospinning. This study aims to determine the effect of PVP variation on the viscosity and morphology of TiO2 nanofibers and to determine the crystal structure of the fibers. Synthesis of TiO2 was carried out using the sol-gel method. TTIP is used as a precursor, ethanol as a solvent, acetic acid as a catalyst and PVP as a fiber-forming polymer. The results of the viscosity measurement show that the amount of PVP used in the sample is directly proportional to the level of solution viscosity. Based on the results of SEM characterization, it showed relatively uniform nanofiber morphology with fiber diameter ranging from 94 nm - 735 µm. The results of TEM characterization showed that the size of TiO2 nanofiber particles ranged from 7-15 nm. The results of XRD analysis showed that the crystal structures formed at a calcination temperature of 450 oC were the anatase and rutile phases.

scholarly journals Nanosized TiO2Photocatalyst Powder via Sol-Gel Method: Effect of Hydrolysis Degree on Powder Properties

2009 ◽  
Vol 2009 ◽  
pp. 1-8 ◽  
Author(s):  
Nor Hafizah ◽  
Iis Sopyan
Keyword(s):  
Crystal Structure ◽  
Surface Area ◽  
Sol Gel ◽  
Xrd Analysis ◽  
Gel Method ◽  
Sol Gel Method ◽  
Hydrolysis Degree ◽  
Method Effect ◽  
Powder Properties ◽  
Dta Curves

NanosizedTiO2powder was synthesized via sol-gel method using titanium tetraisopoxide (TPT) as the precursor. Mol ratios of water to TPT were varied from 1 (Powder A), 2 (Powder B), 3 (Powder C), and 4 (Powder D) to evaluate effect of hydrolysis degree. TG/DTA curves showed that amorphous phase turned to anatase crystal structure at ca. 415, 337, 310, and339∘C for Powders A, B, C, and D, respectively. XRD analysis showed that all the synthesizedTiO2powders were 100% in anatase form with Powders B and C showing considerably higher crystallinities. The powders obtained at lower water to TPT mol ratios were spherical in shape and they became bar-like shapes higher mol ratios. The lower hydrolysis degree led to higher surface area of the Powder A (24.8 m2/g) compared to Powder B (14.6 m2/g). From phenol photocatalytic measurement, Powder B was the most efficient attributed to its higher crystallinity.

scholarly journals Synthesis and Characterization of Ce3+-Doped Ni0.5Cd0.5Fe2O4 Nanoparticles by Sol–Gel Auto-Combustion Method

Coatings ◽  
2021 ◽  
Vol 11 (10) ◽  
pp. 1156
Author(s):  
Danyal Ahmad ◽  
Nasir Mehboob ◽  
Abid Zaman ◽  
Nabeel Ahmed ◽  
Kashif Ahmed ◽  
...  
Keyword(s):  
Crystal Structure ◽  
Crystallite Size ◽  
Sol Gel ◽  
Average Crystallite Size ◽  
Combustion Method ◽  
Xrd Analysis ◽  
Sem Images ◽  
X Ray ◽  
Auto Combustion ◽  
Ray Density

Cerium (Ce)-doped Ni0.5Cd0.5CexFe2−xO4 (0.0 ≤ x ≤ 0.20) was synthesized using the sol–gel auto-combustion method. X-ray diffraction (XRD) analysis revealed that all the samples retained spinel cubic crystal structure with space group Fd3m at 800 °C. Crystal structure parameters, such as lattice constant, average crystallite size, and X-ray density were estimated from the major XRD (311) peak. Bulk density and porosity were also calculated. The average crystallite size was estimated to be in the range of 20–24 nm. SEM images displayed agglomerated particles with a porous morphology. The dielectric constant (ε′) increased and the dielectric loss tangent (tanδ) decreased with rising Ce concentration. The hysteresis loop (M–H loop) was measured at room temperature using a vibrating-sample magnetometer (VSM), which showed a nonlinear decrease in magnetization and coercivity with increasing Ce concentration.

scholarly journals Influence of type of precursors on the sol-gel synthesis of the LaCoO3 nanoparticles

2014 ◽  
Vol 22 (1) ◽  
pp. 1-12 ◽  
Author(s):  
Nicoleta Cornei ◽  
Simona Feraru ◽  
Ion Bulimestru ◽  
Andrei Victor Sandu ◽  
Carmen Mita
Keyword(s):  
Crystal Structure ◽  
Sol Gel ◽  
Chelating Agent ◽  
Xrd Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sol Gel Synthesis ◽  
Perovskite Type ◽  
Type Crystal ◽  
Scanning Electron

Abstract Perovskite-type LaCoO3 was prepared by sol-gel method using nitrates / chlorides as precursors and citric acid as chelating agent. Chemical composition was obtained by means of EDX method. The structures of sintered samples were investigated by scanning electron microscopy (SEM), IR and XRD analysis. The results of X-ray diffraction indicated that the LaCoO3nanopowders obtained using nitrate as precursors had a rhombohedral perovskite-type crystal structure (S. G: R-3c), while that obtained using chloride as precursors had a mixture of LaCoO3, LaOCl and Co3O4. The all lanthanum cobaltites exhibit catalytic activity on the decomposition of hydrogen peroxide, ascribed to their higher surface and Co3+ concentration

Structural, Thermal and Electrical Properties of Doped Poly(3,4 ethylenedioxythiophene)

2016 ◽  
Vol 10 (4) ◽  
pp. 395-400 ◽  
Author(s):  
Deepali Kelkar ◽  
◽  
Ashish Chourasia ◽  
◽  
Keyword(s):  
Crystal Structure ◽  
Electrical Properties ◽  
Xrd Analysis ◽  
Structure Modification ◽  
Camphorsulfonic Acid ◽  
Thermal And Electrical Properties ◽  
Ft Ir

Poly(3,4-ethylenedioxythiophene) (PEDOT) was chemically synthesized, undoped and then re-doped using FeCl3 as well as camphorsulfonic acid (CSA). FT-IR results confirm the nature of the synthesized and doped samples. XRD analysis indicates crystal structure modification after doping and was also used to calculate crystallinity of samples. Crystallinity increases after FeCl3 doping, whereas it reduces due to CSA doping. TGA-DTA results show reduction in Tg value for FeCl3 doped sample while it increases for CSA doped samples compared to that of undoped PEDOT. Reduction in Tg indicates plasticizing effect of FeCl3 whereas increase in Tg show anti-plasticizing effect of CSA in PEDOT. Conductivity value () increases by two orders of magnitude after doping. Log vs. 1/T graph show metallic nature of undoped PEDOT above 308 K, however both doped samples show semiconducting nature from 301 to 383 K.

PENGGUNAAN TiO2 PARTIKEL NANO HASIL SINTESIS BERBASIS AIR MENGGUNAKAN METODA SOL-GEL PADA BAHAN KAPAS SEBAGAI APLIKASI UNTUK TEKSTIL ANTI UV

Arena Tekstil ◽  
2013 ◽  
Vol 28 (1) ◽  
Author(s):  
Maya Komalasari ◽  
Bambang Sunendar
Keyword(s):  
Fourier Transform ◽  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
Sol Gel ◽  
Crosslinking Agent ◽  
X Ray Diffraction ◽  
Nano Tio2 ◽  
X Ray ◽  
Infra Red ◽  
Scanning Electron

Partikel nano TiO2 berbasis air dengan pH basa telah berhasil disintesis dengan menggunakan metode sol-gel dan diimobilisasi pada kain kapas dengan menggunakan kitosan sebagai zat pengikat silang. Sintesis dilakukan  dengan prekursor TiCl4 pada konsentrasi 0,3 M, 0,5 M dan 1 M, dan menggunakan templat kanji dengan proses kalsinasi pada suhu 500˚C selama 2 jam. Partikel nano TiO2 diaplikasikan ke kain kapas dengan metoda pad-dry-cure dan menggunakan kitosan sebagai crosslinking agent. Berdasarkan hasil Scanning Electron Microscope (SEM),diketahui bahwa morfologi partikel TiO2 berbentuk spherical dengan ukuran nano (kurang dari 100 nm). Karakterisasi X-Ray Diffraction (XRD) menunjukkan adanya tiga tipe struktur kristal utama, yaitu (100), (101) dan (102) dengan fasa kristal yang terbentuk adalah anatase dan rutile. Pada karakterisasi menggunakan SEM terhadap serbuk dari TiO2 yang telah diaplikasikan ke permukaan kain kapas, terlihat adanya imobilisasi partikel nano TiO2 melalui ikatan hidrogen silang dengan kitosan pada kain kapas. Hasil analisa tersebut kemudian dikonfirmasi dengan FTIR (Fourier Transform Infra Red) yang hasilnya memperlihatkan puncak serapan pada bilangan gelombang 3495 cm-1, 2546 cm-1, dan 511 cm-1,  yang masing-masing diasumsikan sebagai adanya vibrasi gugus fungsi O-H, N-H dan Ti-O-Ti. Hasil SEM menunjukkan pula bahwa kristal nano yang terbentuk diantaranya adalah fasa rutile , yang berdasarkan literatur terbukti dapatberfungsi sebagai anti UV.

scholarly journals Hydrolytic Modification of SiO2 Microspheres with Na2SiO3 and the Performance of Supported Nano-TiO2 Composite Photocatalyst

Materials ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2553
Author(s):  
Yu Tu ◽  
Weihua Ao ◽  
Chunhong Wang ◽  
Tianyu Ren ◽  
Lijuan Zhang ◽  
...  
Keyword(s):  
Sol Gel ◽  
Active Surface ◽  
Hydroxyl Groups ◽  
Nano Tio2 ◽  
Amorphous Sio2 ◽  
Composite Photocatalyst ◽  
Sio2 Shell ◽  
Functional Efficiency ◽  
Sio2 Microspheres ◽  
Better Than

Modified microspheres (SiO2-M) were obtained by the hydrolytic modification of silicon dioxide (SiO2) microspheres with Na2SiO3, and then, SiO2-M was used as a carrier to prepare a composite photocatalyst (SiO2-M/TiO2) using the sol-gel method; i.e., nano-TiO2 was loaded on the surface of SiO2-M. The structure, morphology, and photocatalytic properties of SiO2-M/TiO2 were investigated. Besides, the mechanism of the effect of SiO2-M was also explored. The results show that the hydrolytic modification of Na2SiO3 coated the surface of SiO2 microspheres with an amorphous SiO2 shell layer and increased the quantity of hydroxyl groups. The photocatalytic performance of the composite photocatalyst was slightly better than that of pure nano-TiO2 and significantly better than that of the composite photocatalyst supported by unmodified SiO2. Thus, increasing the loading capacity of nano-TiO2, improving the dispersion of TiO2, and increasing the active surface sites are essential factors for improving the functional efficiency of nano-TiO2. This work provides a new concept for the design of composite photocatalysts by optimizing the performance of the carrier.

scholarly journals Aqueous Sol-Gel Synthesis of Different Iron Ferrites: From 3D to 2D

Materials ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1554
Author(s):  
Justinas Januskevicius ◽  
Zivile Stankeviciute ◽  
Dalis Baltrunas ◽  
Kęstutis Mažeika ◽  
Aldona Beganskiene ◽  
...  
Keyword(s):  
Magnetic Measurements ◽  
Substrate Surface ◽  
Sol Gel ◽  
Synthesis Method ◽  
Xrd Analysis ◽  
Dip Coating ◽  
Yttrium Iron ◽  
Iron Garnet ◽  
Dip Coating Technique ◽  
Sol Gel Synthesis

In this study, an aqueous sol-gel synthesis method and subsequent dip-coating technique were applied for the preparation of yttrium iron garnet (YIG), yttrium iron perovskite (YIP), and terbium iron perovskite (TIP) bulk and thin films. The monophasic highly crystalline different iron ferrite powders have been synthesized using this simple aqueous sol-gel process displaying the suitability of the method. In the next step, the same sol-gel solution was used for the fabrication of coatings on monocrystalline silicon (100) using a dip-coating procedure. This resulted, likely due to substrate surface influence, in all coatings having mixed phases of both garnet and perovskite. Thermogravimetric (TG) analysis of the precursor gels was carried out. All the samples were investigated by X-ray powder diffraction (XRD) analysis. The coatings were also investigated by scanning electron microscopy (SEM), atomic force microscopy (AFM) and Mössbauer spectroscopy. Magnetic measurements were also carried out.

scholarly journals Surface Chemistry, Crystal Structure, Size and Topography Role in the Albumin Adsorption Process on TiO2 Anatase Crystallographic Faces and Its 3D-Nanocrystal: A Molecular Dynamics Study

Coatings ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 420
Author(s):  
Giuseppina Raffaini
Keyword(s):  
Crystal Structure ◽  
Molecular Dynamics ◽  
Surface Chemistry ◽  
Protein Adsorption ◽  
Adsorption Process ◽  
Sol Gel ◽  
Interaction Strength ◽  
Theoretical Work ◽  
Blood Protein ◽  
Tio2 Anatase

TiO2 is widely used in biomaterial implants. The topography, chemical and structural properties of titania surfaces are an important aspect to study. The size of TiO2 nanoparticles synthetized by sol–gel method can influence the responses in the biological environment, and by using appropriate heat treatments different contents of different polymorphs can be formed. Protein adsorption is a crucial step for the biological responses, involving, in particular, albumin, the most abundant blood protein. In this theoretical work, using molecular mechanics and molecular dynamics methods, the adsorption process of an albumin subdomain is reported both onto specific different crystallographic faces of TiO2 anatase and also on its ideal three-dimensional nanosized crystal, using the simulation protocol proposed in my previous theoretical studies about the adsorption process on hydrophobic ordered graphene-like or hydrophilic amorphous polymeric surfaces. The different surface chemistry of anatase crystalline faces and the nanocrystal topography influence the adsorption process, in particular the interaction strength and protein fragment conformation, then its biological activity. This theoretical study can be a useful tool to better understand how the surface chemistry, crystal structure, size and topography play a key role in protein adsorption process onto anatase surface so widely used as biomaterial.

scholarly journals Hard Coating Materials Based on Photo-Reactive Silsesquioxane for Flexible Application: Improvement of Flexible and Hardness Properties by High Molecular Weight

Polymers ◽  
2021 ◽  
Vol 13 (10) ◽  
pp. 1564
Author(s):  
Jong Tae Leem ◽  
Woong Cheol Seok ◽  
Ji Beom Yoo ◽  
Sangkug Lee ◽  
Ho Jun Song
Keyword(s):  
Molecular Weight ◽  
Surface Morphology ◽  
High Molecular Weight ◽  
Sol Gel ◽  
Xrd Analysis ◽  
Polyhedral Oligomeric Silsesquioxanes ◽  
Coating Materials ◽  
Pencil Hardness ◽  
Coated Film ◽  
Flexible Application

EPOSS of polyhedral oligomeric silsesquioxanes (POSS) mixture structure and LPSQ of ladder-like polysilsesquioxane (LPSQ) structure were synthesized via sol–gel reaction. EPSQ had a high molecular weight due to polycondensation by potassium carbonate. The EPSQ film showed uniform surface morphology due to regular double-stranded structure. In contrast, the EPOSS-coated film showed nonuniform surface morphology due to strong aggregation. Due to the aggregation, the EPOSS film had shorter d-spacing (d1) than the EPSQ film in XRD analysis. In pencil hardness and nanoindentation analysis, EPSQ film showed higher hardness than the EPOSS film due to regular double-stranded structure. In addition, in the in-folding (r = 0.5 mm) and out-folding (r = 5 mm) tests, the EPSQ film did not crack unlike the EPOSS coated film.

Sign in / Sign up

Export Citation Format

Share Document