scholarly journals Surface Properties and Mechanical Performance of Ti-Based Dental Materials: Comparative Effect of Valve Alloying Elements and Structural Defects

2021 ◽  
Author(s):  
Agata Sotniczuk ◽  
Kamil Majchrowicz ◽  
Donata Kuczyńska-Zemła ◽  
Marcin Pisarek ◽  
Bogusława Adamczyk-Cieślak ◽  
...  
Keyword(s):  
Oxide Layer ◽  
Surface Properties ◽  
Mechanical Performance ◽  
Dental Materials ◽  
Alloying Elements ◽  
Structural Defects ◽  
Native Oxide ◽  
Oral Environment ◽  
Industrial Level ◽  
Zr Alloy

AbstractTwo approaches can be taken when designing properties of the native oxide layers formed on Ti-based biomedical materials: (i) changing the chemical composition of the substrate by adding biocompatible, valve alloying elements, and (ii) changing the microstructure of the substrate—especially its level of defectiveness—through large plastic deformation. However, especially in the aggressive fluoridated oral environment, it is still unknown what factor is more effective in terms of enhancing oxide layer protectiveness against biocorrosion: (i) the presence of valve alloying elements, or (ii) a high number of structural defects. To gain knowledge about the separate influence of both of these factors, surface properties were examined for commercially pure Ti and Ti–Nb–Ta–Zr alloy in microcrystalline state as well as after multiple-pass cold rolling, a process that can be readily scaled up to the industrial level. This study showed that while valve-alloying elements and structural defects individually have a beneficial effect on Ti oxide layer properties in fluoridated medium, they not have to act in a synergistic manner. These findings have to be taken into account when designing future Ti-based dental materials together with analyzing their mechanical performance with respect to mechanical strength and elastic properties.

scholarly journals Is Micro X-ray Computer Tomography a Suitable Non-Destructive Method for the Characterisation of Dental Materials?

Polymers ◽  
2021 ◽  
Vol 13 (8) ◽  
pp. 1271
Author(s):  
Andreas Koenig ◽  
Leonie Schmohl ◽  
Johannes Scheffler ◽  
Florian Fuchs ◽  
Michaela Schulz-Siegmund ◽  
...  
Keyword(s):  
Flexural Strength ◽  
Computer Tomography ◽  
Mechanical Performance ◽  
Dental Materials ◽  
Three Dimensional ◽  
X Rays ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Multiple Measurements ◽  
High Doses

The aim of the study was to investigate the effect of X-rays used in micro X-ray computer tomography (µXCT) on the mechanical performance and microstructure of a variety of dental materials. Standardised bending beams (2 × 2 × 25 mm3) were forwarded to irradiation with an industrial tomograph. Using three-dimensional datasets, the porosity of the materials was quantified and flexural strength was investigated prior to and after irradiation. The thermal properties of irradiated and unirradiated materials were analysed and compared by means of differential scanning calorimetry (DSC). Single µXCT measurements led to a significant decrease in flexural strength of polycarbonate with acrylnitril-butadien-styrol (PC-ABS). No significant influence in flexural strength was identified for resin-based composites (RBCs), poly(methyl methacrylate) (PMMA), and zinc phosphate cement (HAR) after a single irradiation by measurement. However, DSC results suggest that changes in the microstructure of PMMA are possible with increasing radiation doses (multiple measurements, longer measurements, higher output power from the X-ray tube). In summary, it must be assumed that X-ray radiation during µXCT measurement at high doses can lead to changes in the structure and properties of certain polymers.

scholarly journals Effects of ionizing radiation on surface properties of current restorative dental materials

2021 ◽  
Vol 32 (6) ◽  
Author(s):  
Débora Michelle Gonçalves de Amorim ◽  
Aretha Heitor Veríssimo ◽  
Anne Kaline Claudino Ribeiro ◽  
Rodrigo Othávio de Assunção e Souza ◽  
Isauremi Vieira de Assunção ◽  
...  
Keyword(s):  
Ionizing Radiation ◽  
Surface Properties ◽  
Resin Composite ◽  
Dental Materials ◽  
Glass Ionomer Cement ◽  
Contact Angles ◽  
Glass Ionomer ◽  
Post Radiation ◽  
Restorative Dental Materials ◽  
Ionomer Cement

AbstractTo investigate the impact of radiotherapy on surface properties of restorative dental materials. A conventional resin composite—CRC (Aura Enamel), a bulk-fill resin composite—BFRC (Aura Bulk-fill), a conventional glass ionomer cement—CGIC (Riva self cure), and a resin-modified glass ionomer cement—RMGIC (Riva light cure) were tested. Forty disc-shaped samples from each material (8 mm diameter × 2 mm thickness) (n = 10) were produced according to manufacturer directions and then stored in water distilled for 24 h. Surface wettability (water contact angle), Vickers microhardness, and micromorphology through scanning electron microscopy (SEM) before and after exposition to ionizing radiation (60 Gy) were obtained. The data were statistically evaluated using the two-way ANOVA and Tukey posthoc test (p < 0.05). Baseline and post-radiation values of contact angles were statistically similar for CRC, BFRC, and RMGIC, whilst post-radiation values of contact angles were statistically lower than baseline ones for CGIC. Exposition to ionizing radiation statistically increased the microhardness of CRC, and statistically decreased the microhardness of CGIC. The surface micromorphology of all materials was changed post-radiation. Exposure to ionizing radiation negatively affected the conventional glass ionomer tested, while did not alter or improved surface properties testing of the resin composites and the resin-modified glass ionomer cement tested.

scholarly journals Investigation of Graphene Derivatives on Electrical Properties of Alkali Activated Slag Composites

Materials ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4374
Author(s):  
Wu-Jian Long ◽  
Xuanhan Zhang ◽  
Biqin Dong ◽  
Yuan Fang ◽  
Tao-Hua Ye ◽  
...  
Keyword(s):  
Graphene Oxide ◽  
Electrical Properties ◽  
Mechanical Performance ◽  
Structural Defects ◽  
Alkali Activated Slag ◽  
Mechanical And Electrical Properties ◽  
Reduced Graphene ◽  
Graphene Derivatives ◽  
Activated Slag ◽  
Alkali Activated

Reduced graphene oxide (rGO) has been widely used to modify the mechanical performance of alkali activated slag composites (AASC); however, the mechanism is still unclear and the electrical properties of rGO reinforced AASC are unknown. Here, the rheological, mechanical, and electrical properties of the AASC containing rGO nanosheets (0, 0.1, 0.2, and 0.3 wt.%) are investigated. Results showed that rGO nanosheets addition can significantly improve the yield stress, plastic viscosity, thixotropy, and compressive strength of the AASC. The addition of 0.3 wt.% rGO nanosheets increased the stress, viscosity, thixotropy, and strength by 186.77 times, 3.68 times, 15.15 times, and 21.02%, respectively. As for electrical properties, the impedance of the AASC increased when the rGO content was less than 0.2 wt.% but decreased with the increasing dosage. In contrast, the dielectric constant and electrical conductivity of the AASC containing rGO nanosheets decreased and then increased, which can be attributed to the abundant interlayer water and the increasing structural defects as the storage sites for charge carriers, respectively. In addition, the effect of graphene oxide (GO) on the AASC is also studied and the results indicated that the agglomeration of GO nanosheets largely inhibited the application of it in the AASC, even with a small dosage.

Wettability in pressure infiltration of SiC and oxidized SiC particle compacts by molten Al and Al-12wt%Si alloy

2007 ◽  
Vol 22 (8) ◽  
pp. 2273-2278 ◽  
Author(s):  
J.M. Molina ◽  
J. Tian ◽  
C. Garcia-Cordovilla ◽  
E. Louis ◽  
J. Narciso
Keyword(s):  
Contact Angle ◽  
Oxide Layer ◽  
Low Temperatures ◽  
Native Oxide ◽  
Native Oxide Layer ◽  
Threshold Pressure ◽  
Pressure Infiltration ◽  
Surface Conditions ◽  
Infiltration Behavior ◽  
Sic Particle

The infiltration behavior of compacts of SiC particles in two surface conditions, as-received and thermally oxidized, was investigated by using pure Al and Al-12wt%Si as infiltrating metals. Analysis of the threshold pressure for infiltration revealed that the process is governed by the same contact angle for all different systems, no matter the metal or particle condition. This leads to the conclusion that oxidation does not modify the wetting characteristics of the particles, most probably because they are already covered by a thin native oxide layer that remains unaltered in processing routes involving short contact times and low temperatures, such as actual conditions of pressure infiltration at 700 °C.

scholarly journals The Benefits of Smart Nanoparticles in Dental Applications

2021 ◽  
Vol 22 (5) ◽  
pp. 2585
Author(s):  
Silvia Vasiliu ◽  
Stefania Racovita ◽  
Ionela Aurica Gugoasa ◽  
Maria-Andreea Lungan ◽  
Marcel Popa ◽  
...  
Keyword(s):  
Metallic Nanoparticles ◽  
Periodontal Diseases ◽  
Dental Materials ◽  
Moisture Stress ◽  
New Methods ◽  
Strong Trend ◽  
Scientific World ◽  
Oral Environment ◽  
Recent Developments ◽  
Dental Applications

Dentistry, as a branch of medicine, has undergone continuous evolution over time. The scientific world has focused its attention on the development of new methods and materials with improved properties that meet the needs of patients. For this purpose, the replacement of so-called “passive” dental materials that do not interact with the oral environment with “smart/intelligent” materials that have the capability to change their shape, color, or size in response to an externally stimulus, such as the temperature, pH, light, moisture, stress, electric or magnetic fields, and chemical compounds, has received much attention in recent years. A strong trend in dental applications is to apply nanotechnology and smart nanomaterials such as nanoclays, nanofibers, nanocomposites, nanobubbles, nanocapsules, solid-lipid nanoparticles, nanospheres, metallic nanoparticles, nanotubes, and nanocrystals. Among the nanomaterials, the smart nanoparticles present several advantages compared to other materials, creating the possibility to use them in various dental applications, including preventive dentistry, endodontics, restoration, and periodontal diseases. This review is focused on the recent developments and dental applications (drug delivery systems and restoration materials) of smart nanoparticles.

Redistribution of Internal Force under Structural Defect and Non-Linear Spatial Stability under Live Load and Wind of Tied-Arch Bridge

2013 ◽  
Vol 477-478 ◽  
pp. 640-645
Author(s):  
Qian Hui Pu ◽  
Hu Zhao
Keyword(s):  
Safety Factor ◽  
Mechanical Performance ◽  
Influence Factors ◽  
Internal Force ◽  
Structural Defects ◽  
Live Load ◽  
Positive Contribution ◽  
Arch Bridge ◽  
Initial Defect ◽  
Tied Arch Bridge

To study the mechanical performance and stability of tied-arch bridge under structural defects and damages, limited element modal of Panzhihua Luoguo Jinshajiang Bridge was established and analyzed. Firstly, some typical damage models and their influence factors were presented. Then, based on the model established, change of suspender force caused by arch rib lineation defect, hanger lineation defect and boom failure was calculated respectively. The stability safety factor under the load group composed of dead load, live load and wind was calculated as well as the second-class nonlinear stability safety factor under structural initial defect. Calculation results shows that, suspender forces were more sensitive to archs vertical defect than to transverse defect. While, short hangers were more sensitive to lineation defect than long ones, and secondary inner force in short booms were bigger than in long ones. The result also tells that lateral wind is bad to lateral stability. Lift wind, somehow, makes positive contribution to structures in-plane stability. Structural initial defect can draw down the second-class stability safety factor under geometric nonlinear condition.

The Effect of Surface States on Secondary Electron (SE) Dopant Contrast from Silicon p-n Junctions

2007 ◽  
Vol 1026 ◽  
Author(s):  
Augustus K. W. Chee ◽  
Conny Rodenburg ◽  
Colin John Humphreys
Keyword(s):  
Oxide Layer ◽  
Computer Modelling ◽  
Surface States ◽  
Native Oxide ◽  
Native Oxide Layer ◽  
Element Analysis ◽  
Surface Band ◽  
Band Bending ◽  
Wide Range ◽  
Se Doping

AbstractDetailed computer modelling using finite-element analysis was performed for Si p-n junctions to investigate the effects of surface states and doping concentrations on surface band-bending, surface junction potentials and external patch fields. The density of surface states was determined for our Si specimens with a native oxide layer. Our calculations show that for a typical density of surface states for a Si specimen with a native oxide layer, the effects of external patch fields are negligible and the SE doping contrast is due to the built-in voltage across the p-n junction modified by surface band-bending. There is a good agreement between the experimental doping contrast and the calculated junction potential just below the surface, taking into account surface states, for a wide range of doping concentrations.

Nano-Thick Amorphous Oxide Layer Produced by Plasma on Type 316L Stainless Steel for Improved Corrosion Resistance Under Plastic Deformation

CORROSION ◽  
10.5006/2674 ◽  
2018 ◽  
Vol 74 (9) ◽  
pp. 1011-1022 ◽  
Author(s):  
Megan Mahrokh Dorri ◽  
Stéphane Turgeon ◽  
Maxime Cloutier ◽  
Pascale Chevallier ◽  
Diego Mantovani
Keyword(s):  
Plastic Deformation ◽  
Stainless Steel ◽  
Oxide Layer ◽  
Electrochemical Impedance ◽  
Open Circuit ◽  
Localized Corrosion ◽  
Native Oxide ◽  
Native Oxide Layer ◽  
Amorphous Oxide ◽  
Amorphous Oxide Layer

Localized corrosion constitutes a major concern in medical devices made of stainless steel. The conventional approach to circumvent such a problem is to convert the surface polycrystalline microstructure of the native oxide layer to an amorphous oxide layer, a few micrometers thick. This process cannot, however, be used for devices such as stents that undergo plastic deformation during their implantation, especially those used in vascular surgery for the treatment of cardiac, neurological, and peripheral vessels. This work explores the feasibility of producing a nano-thick plastic-deformation resistant amorphous oxide layer by plasma-based surface modifications. By varying the plasma process parameters, oxide layers with different features were produced and their properties were investigated before and after clinically-relevant plastic deformation. These properties and the related corrosion mechanisms were mainly evaluated using the electrochemical methods of open-circuit potential, cyclic potentiodynamic polarization, and electrochemical impedance spectroscopy. Results showed that, under optimal conditions, the resistance to corrosion and to the permeation of ions in a phosphate buffered saline, even after deformation, was significantly enhanced.

Sign in / Sign up

Export Citation Format

Share Document