scholarly journals Spent mushroom substrate: a crucial biosorbent for the removal of ferrous iron from groundwater

2021 ◽  
Vol 3 (1) ◽  
Author(s):  
D. Menaga ◽  
S. Rajakumar ◽  
P. M. Ayyasamy
Keyword(s):  
Ferrous Iron ◽  
Tamil Nadu ◽  
Contaminated Water ◽  
Spent Mushroom Substrate ◽  
Pseudo First Order Reaction ◽  
Time Intervals ◽  
New Approach ◽  
First Order ◽  
Sorption Ability ◽  
Pseudo Second Order

Abstract A new approach was carried out with the spent mushroom substrate (SMS) of Pleurotus florida on ferrous iron (Fe2+) removal using live, dead and pretreated substrate. In this study, the various dosage levels of SMS namely, 0.25, 0.50, 1.0 and 1.50 g/50 mL were used for the removal of Fe2+ at different time intervals for 90 min. The effect of various temperatures and pH on Fe2+ removal was studied with optimized dosages and time intervals. The biosorption potential of P. florida SMS was checked against the iron-contaminated groundwater collected from in and around Salem, Namakkal and Dharmapuri districts of Tamil Nadu. The biosorption data were obtained and analyzed in terms of their kinetic behavior. Among the SMS of P. florida, the live SMS showed potential Fe2+ removal (100%) from aqueous metal solution in all the tested concentrations. SMS of P. florida showed high potential removal of Fe2+ in neutral pH, at room temperature and explored an efficient sorption ability (100%) in the tested water sample (SW10). The adsorption kinetic values fitted very well with pseudo-second-order when comparing with pseudo-first-order reaction. FTIR, SEM and EDX analysis proved the accumulation of Fe2+ by the SMS. The present study confirmed that the live SMS of P. florida may serve as a potential and eco-friendly biosorbent for removal of Fe2+ from the iron-contaminated water. Graphic abstract

scholarly journals Reuse of Newspaper As An Adsorbent For Cu (II) Removal By Citric Acid Modification

2018 ◽  
Vol 156 ◽  
pp. 02012 ◽  
Author(s):  
Mardiah ◽  
Rif’an Fathoni ◽  
Pratiwi Pudyaningtyas ◽  
Hamdania Gamu ◽  
Rinaldy
Keyword(s):  
Citric Acid ◽  
Adsorption Process ◽  
Kinetic Studies ◽  
Order Reaction ◽  
Acid Modification ◽  
Pseudo First Order Reaction ◽  
First Order ◽  
Pseudo Second Order ◽  
Heavy Metal Adsorbent ◽  
The Impact

High Consumption of paper, bring the impact of the waste paper itself. And the utilization of the paper is limited to recycled products and crafts, whereas paper such as newspaper still contains cellulose that can be potential to be used as a heavy metal adsorbent. In this study, newspaper was dissolved in sodium bicarbonate to reduce various impurities and then was reacted with citric acid (CA). The modified adsorbent was characterized by FTIR and was tested for adsorb Cu(II) in artificial solution. After adsorption process, the solution was filtered and analysed using Atomic Absorption Spectrophotometer (AAS). The adsorption experimental data was fitted to Langmuir, Freundlich, Tempkin, and Dubinin-Radushkevich for equilibrium model and was fitted to pseudo first order reaction and pseudo second order reaction for kinetic studies. The result showed that CA-modification newspaper able to remove heavy metals Cu(II) in solution.

scholarly journals Microwave-Assisted Transesterification of Kusum Oil: Parametric, Kinetic and Thermodynamic Studies

2020 ◽  
Vol 32 (11) ◽  
pp. 2893-2903
Author(s):  
SHEETAL N. NAYAK ◽  
MILAP G. NAYAK ◽  
CHANDRAKANT P. BHASIN
Keyword(s):  
Activation Energy ◽  
Reaction Rate ◽  
Frequency Factor ◽  
Molar Ratio ◽  
Pseudo First Order Reaction ◽  
Time Intervals ◽  
First Order ◽  
Microwave Assisted ◽  
Lower Heat ◽  
Kinetic And Thermodynamic Studies

Microwave-assisted transesterification of non-edible oil to produce biodiesel is gaining attention due to lower heat loss as well as rapid conversion. In this study, esterified kusum oil as a feedstock was transesterified in the presence of Ba(OH)2. At 800 W microwave power and constant magnetic stirring the effect of important process parameters such as solvent methanol molar ratio, Ba(OH)2, temperature, and time on biodiesel yield were evaluated. The parametric study suggested that 9:1 M methanol, 65 ºC reaction temperature, 2.5 wt% Ba(OH)2 catalyst and 3.5 min of transesterification time gave close to 96% biodiesel yield. At the above conditions of methanol and catalyst, the reaction kinetics and thermodynamic study were performed using different time intervals. The microwave-assisted transesterification followed pseudo-first-order reaction rate with 34.57 kJ/mol K activation energy and 205664 min-1 frequency factor. The reduction in activation energy and increase in the frequency factor reveal the non-thermal effect associated with microwave heating. The thermodynamic properties evaluated using the Eyring equation suggests non-spontaneity and endothermic nature of transesterification.

Adsorption of Methylene Blue (MB) Dye in Wastewater by Electrospun Polysulfone (PSF)/Organo-Montmorillonite (O-MMT) Nanostructured Membrane

2018 ◽  
Vol 916 ◽  
pp. 120-124 ◽  
Author(s):  
Ruth R. Aquino ◽  
Marvin S. Tolentino ◽  
Bianca Mae Z. Crisogono ◽  
Sarah Katrina V. Salvacion
Keyword(s):  
Adsorption Equilibrium ◽  
Order Kinetic ◽  
Adsorption Efficiency ◽  
Time Intervals ◽  
First Order ◽  
Equilibrium Data ◽  
Pseudo Second Order ◽  
Absorbance Reading ◽  
Simulated Wastewater ◽  
Adsorption Equilibrium Data

In this study, organo-montmorillonite was utilized as an additive for the fabrication of the nanostructured membrane via electrospinning process.The purpose of this study is to investigate the performance of 95% PSF and 5% O-MMT blend in terms of its adsorption capacity towards MB dye in wastewater and comparing it to pure PSF membranes. Pure PSF and 5% O-MMT blend were immersed in the simulated wastewater at different time intervals (1, 5, 12, 24 and 48 hours), and the change in MB dye concentration was observed by UV-Vis absorbance reading. To determine the mechanism of adsorption, the data obtained were subjected to pseudo-first order and pseudo-second order kinetic models, and were fitted to Langmuir, Freundlich and Temkin adsorption isotherms to determine the adsorption equilibrium data. The results show that the adsorption efficiency was improved by 5.32%.

scholarly journals Oxidative degradation of gentamicin present in water by an electro-Fenton process and biodegradability improvement

2019 ◽  
Vol 17 (1) ◽  
pp. 1017-1025
Author(s):  
Mohamed Réda Arhoutane ◽  
Muna Shueai Yahya ◽  
Miloud El Karbane ◽  
Kacem El Kacemi
Keyword(s):  
Chemical Oxygen Demand ◽  
Biological Process ◽  
Oxidative Degradation ◽  
Oxygen Demand ◽  
Polluted Water ◽  
Applied Current ◽  
Pseudo First Order Reaction ◽  
First Order ◽  
Appropriate Treatment ◽  
By Products

AbstractIn the context of environmental protection, where there is a need to develop effective operations for carrying out appropriate treatment of polluted water by pharmaceuticals. Therefore, the present study aims at evaluating the degradation for gentamicin through electro-Fenton (EF) operation, through taking into consideration the effect of several parameters of experimental in the process, namely, the concentration of initial gentamicin, the applied current and the Fe+2 (II) quantities. The (EF) operation employed involves a carbon-felt as cathode and platinum as anode at pH 3. Studies for the gentamicin kinetics is monitored by HPLC giving a pseudo-first order reaction following by a chemical oxygen demand, with a reached degree of mineralization 96% after of four hours of treatment through current 100 mA/cm2 with 0.1 mM of Fe+2. We find that the degradation for molecule of gentamicin is accompanied by an augmentation of the biodegradability, assesse through the Biochemical Oxygen Demand (BOD5) on chemical oxygen demand (COD) ratio, that augmentation from 0 to 0.41 before treatment after 30 min for EF treatment, showing that there is potential for conjugation of the EF process and the biological process. Furthermore, the by-products have been identified on the basis of HPLC-MS/MS results.

Efficient adsorption of chlorpyrifos onto modified activated carbon by gamma irradiation; a plausible adsorption mechanism

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Mohamed S. Yahia ◽  
Ahmed S. Elzaref ◽  
Magdy B. Awad ◽  
Ahmed M. Tony ◽  
Ahmed S. Elfeky
Keyword(s):  
Gamma Irradiation ◽  
Area Measurement ◽  
Maximum Adsorption Capacity ◽  
X Ray Diffraction ◽  
X Ray ◽  
First Order ◽  
Pseudo Second Order ◽  
Ft Ir ◽  
Pseudo First Order ◽  
Kinetics Of

Abstract Commercial Granulated Active Carbon (GAC) has been modified using 10 Gy dose Gamma irradiation (GAC10 Gy) for increasing its ability of air purification. Both, the raw and treated samples were applied for removing Chlorpyrifos pesticide (CPF) from ambient midair. Physicochemical properties of the two materials were characterized by Fourier Transform Infrared (FT-IR) and Raman spectroscopy. The phase formation and microstructure were monitored using X-ray Diffraction (XRD), Scanning Electron Microscopy (SEM), supported with Energy-Dispersive X-ray (EDX). The Surface area measurement was detected using BET particle size prosometry. Obtained outcomes showed that, the maximum adsorption capacity, given by Langmuir equations, was greatly increased from 172.712 to 272.480 mg/g for GAC and GAC10 Gy, respectively, with high selectivity. The overall removal efficiency of GAC10 Gy was notably comparable to that of the original GAC-sorbent. The present study indicated that, gamma irradiation could be a promising technique for treating GAC and turned it more active in eliminating the pesticides pollutants from surrounding air. The data of equilibrium has been analyzed by Langmuir and Freundlich models, that were considerably better suited for the investigated materials than other models. The process kinetics of CPF adsorbed onto both tested carbon versions were found to obey the pseudo first order at all concentrations with an exception at 70 mg/l using GAC, where, the spontaneous exothermic adsorption of Chlorpyrifos is a strong function for the pseudo-first order (PFO) and pseudo second order (PSO) kinetics.

scholarly journals Solvent-Free Synthesis of Phosphonic Graphene Derivative and Its Application in Mercury Ions Adsorption

Nanomaterials ◽  
2019 ◽  
Vol 9 (4) ◽  
pp. 485
Author(s):  
Robert Olszewski ◽  
Małgorzata Nadolska ◽  
Marcin Łapiński ◽  
Marta Prześniak-Welenc ◽  
Bartłomiej Cieślik ◽  
...  
Keyword(s):  
Adsorption Efficiency ◽  
Mercury Ions ◽  
High Adsorption ◽  
Adsorption Selectivity ◽  
Nickel Ions ◽  
Cadmium Ions ◽  
First Order ◽  
Bivalent Ions ◽  
Pseudo Second Order ◽  
Solvent Free Synthesis

Functionalized graphene was efficiently prepared through ball-milling of graphite in the presence of dry ice. In this way, oxygen functional groups were introduced into material. The material was further chemically functionalized to produce graphene derivative with phosphonic groups. The obtained materials were characterized by spectroscopic and microscopic methods, along with thermogravimetric analysis. The newly developed material was used as an efficient mercury adsorbent, showing high adsorption efficiency. The adsorption isotherms were fitted using Freundlich and Langmuir models. The adsorption kinetics were fitted with pseudo-first order and pseudo-second order models. Adsorption selectivity was determined in the presence of cadmium ions and nickel ions. The presence of mentioned bivalent ions in the solution did not affect mercury adsorption efficiency.

scholarly journals Comparative studies on the removal of copper (II) by Ulva fasciata activated carbon and commercially activated carbon

2012 ◽  
Vol 14 (4) ◽  
pp. 88-94 ◽  
Author(s):  
R.P. Suresh Jeyakumar ◽  
V. Chandrasekaran
Keyword(s):  
Activated Carbon ◽  
Activated Carbons ◽  
Synthetic Wastewater ◽  
Batch Adsorption ◽  
First Order ◽  
Ulva Fasciata ◽  
Adsorption Data ◽  
Pseudo Second Order ◽  
Pseudo First Order ◽  
Adsorbent Dose

Abstract In this work, the efficiency of Ulva fasciata sp. activated carbons (CCUC, SCUC and SSUC) and commercially activated carbon (CAC) were studied for the removal of Cu (II) ions from synthetic wastewater. Batch adsorption experiments were carried out as a function of pH, contact time, initial copper concentration and adsorbent dose. The percentage adsorption of copper by CCUC, SSUC, SCUC and CAC are 88.47%, 97.53%, 95.78% and 77.42% respectively. Adsorption data were fitted with the Langmuir, Freundlich and Temkin models. Two kinetic models pseudo first order and the pseudo second order were selected to interpret the adsorption data.

scholarly journals Eggshell Powder as an Adsorbent for Removal of Fluoride from Aqueous Solution: Equilibrium, Kinetic and Thermodynamic Studies

2012 ◽  
Vol 9 (3) ◽  
pp. 1457-1480 ◽  
Author(s):  
R. Bhaumik ◽  
N. K. Mondal ◽  
B. Das ◽  
P. Roy ◽  
K. C. Pal ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Adsorption Process ◽  
Low Cost ◽  
Fluoride Removal ◽  
Contaminated Water ◽  
Fluoride Adsorption ◽  
Langmuir Isotherm Model ◽  
Pseudo Second Order ◽  
Kinetic And Thermodynamic Studies ◽  
Maximum Removal

A new medium, eggshell powder has been developed for fluoride removal from aqueous solution. Fluoride adsorption was studied in a batch system where adsorption was found to be pH dependent with maximum removal efficiency at 6.0. The experimental data was more satisfactorily fitted with Langmuir isotherm model. The kinetics and the factor controlling adsorption process fully accepted by pseudo-second-order model were also discussed. Eawas found to be 45.98 kJmol-1by using Arrhenius equation, indicating chemisorption nature of fluoride onto eggshell powder. Thermodynamic study showed spontaneous nature and feasibility of the adsorption process with negative enthalpy (∆H0) value also supported the exothermic nature. Batch experiments were performed to study the applicability of the adsorbent by using fluoride contaminated water collected from affected areas. These results indicate that eggshell powder can be used as an effective, low-cost adsorbent to remove fluoride from aqueous solution as well as groundwater.

The effect of the textile industry dye bath additive EDTMPA on colour removal characteristics by ozone oxidation

2007 ◽  
Vol 55 (10) ◽  
pp. 145-153 ◽  
Author(s):  
T. Ölmez ◽  
I. Kabdaşlı ◽  
O. Tünay
Keyword(s):  
Organic Matter ◽  
Textile Industry ◽  
Reaction Rates ◽  
Textile Dye ◽  
Pseudo First Order Reaction ◽  
Ozone Oxidation ◽  
Reactive Dyeing ◽  
First Order ◽  
Organic Matter Oxidation ◽  
Pseudo First Order

In this study, the effects of the phosphonic acid based sequestering agent EDTMPA used in the textile dye baths on colour and organic matter removal by ozone oxidation was experimentally investigated. Procion Navy HEXL dyestuff that has been commonly used for the reactive dyeing of cellulose fibers was selected as the model component. The organic matter oxidation by ozone was determined to obey the pseudo-first order kinetics as they are treated singly or in combination. COD removal rates obtained from pseudo-first order reaction kinetics showed that oxidation of Navy HEXL alone (0.0947 L/min) was faster than that of EDTMPA (0.0171 L/min) and EDTMPA with dye (0.0155 L/min) at pH 3.0. It was also found that reaction rates of single EDTMPA removal and EDTMPA and dye mixture removal increased as the reaction pH was increased from 3.0 to 10.5.

Multifactorial optimization of the decolorisation parameters of wastewaters resulting from dyeing flowers

2009 ◽  
Vol 59 (7) ◽  
pp. 1361-1369 ◽  
Author(s):  
Edison Gil Pavas ◽  
Miguel Ángel Gómez-García
Keyword(s):  
Hydrogen Peroxide ◽  
Organic Matter ◽  
Experimental Design ◽  
Order Reaction ◽  
Pseudo First Order Reaction ◽  
First Order ◽  
Effluent Standards ◽  
Degradation Of Dyes ◽  
Pseudo First Order ◽  
Dyes Mixture

This work deals with the treatment of the wastewaters resulting from the process of dyeing flowers. In some local cases for growing flowers near to Medellín (Colombia), wastewater color was found to be one of the main problems in meeting local effluent standards. Wastewaters were treated by photodegradation process (which includes photocatalysis) to achieve the degradation of dyes mixture and organic matter in the wastewater. A multifactorial experimental design was proposed, including as experimental factors the following variables: pH, and the concentration of both catalyst (TiO2) and hydrogen peroxide (H2O2). According to the obtained results, at the optimized variables values, it is possible to reach a 99% reduction of dyes, a 76.9% of mineralization (TOC) and a final biodegradability of 0.834. Kinetic analysis allows proposing a pseudo first order reaction for the reduction, the mineralization, and the biodegradation processes.

Sign in / Sign up

Export Citation Format

Share Document