scholarly journals Computational evaluation of a novel beta radiation probe design using integrated circuits

2021 ◽  
Vol 3 (3) ◽  
Author(s):  
Jeremy W. King ◽  
Manit D. Shah ◽  
Craig M. Marianno ◽  
Sunil P. Khatri ◽  
Sunil S. Chirayath
Keyword(s):  
Integrated Circuits ◽  
Natural Rubber ◽  
Integrated Circuit ◽  
Maximum Energy ◽  
Beta Particle ◽  
Particle Detection ◽  
Beta Particles ◽  
Beta Energy ◽  
Energy Discrimination ◽  
Interaction Probability

AbstractResearchers at Texas A&M University (TAMU) have designed the radiation integrated circuit (RIC) for deployment as a new radiation detection system. Most integrated circuits are susceptible to radiation-induced failures, and decades of research have gone into solving this problem. Research at TAMU has led to a novel integrated circuit design that utilizes both radiation-hardened areas (RHAs) and radiation-sensitive areas (RSAs) to take advantage of these failures. The RSAs are susceptible to charged particle interactions, allowing the RIC to detect alpha and beta particles. However, beta particles are more penetrating compared to alpha particles, resulting in a lower interaction probability for beta particles incident on a bare RIC. In any material, the higher the beta energy, the deeper the beta particle can penetrate; therefore, the use of a wedge-shaped attenuator for beta particle detection not only increases interaction probability, but also provides the capability to perform maximum beta energy discrimination in the field. The objective of this research was to optimize the design of the RIC. Monte Carlo N-particle radiation transport code (MCNP) simulations assessed the beta particle detection and maximum energy discrimination performance of plate glass, borosilicate (Pyrex®) glass, acrylic (Lucite®), and natural rubber attenuators. In this proof-of-concept analysis, natural rubber was observed to be the optimal attenuating material for the beta probe with respect to maximum energy discrimination capability and weight, but all materials considered proved to be good candidates. The results of this study are promising and indicate the potential to achieve maximum beta particle energy discrimination of 50 keV using a wedged, natural rubber attenuator on the RIC.

Scanning Electron Microscopy in Hybrid Microelectronics

1976 ◽  
Vol 34 ◽  
pp. 456-457
Author(s):  
S. Khadpe ◽  
R. Faryniak
Keyword(s):  
Integrated Circuits ◽  
Thick Film ◽  
Integrated Circuit ◽  
Failure Modes ◽  
Three Dimensional ◽  
Circuit Components ◽  
Hybrid Microcircuit ◽  
Electrical Connections ◽  
Scanning Electron

The Scanning Electron Microscope (SEM) is an important tool in Thick Film Hybrid Microcircuits Manufacturing because of its large depth of focus and three dimensional capability. This paper discusses some of the important areas in which the SEM is used to monitor process control and component failure modes during the various stages of manufacture of a typical hybrid microcircuit.Figure 1 shows a thick film hybrid microcircuit used in a Motorola Paging Receiver. The circuit consists of thick film resistors and conductors screened and fired on a ceramic (aluminum oxide) substrate. Two integrated circuit dice are bonded to the conductors by means of conductive epoxy and electrical connections from each integrated circuit to the substrate are made by ultrasonically bonding 1 mil aluminum wires from the die pads to appropriate conductor pads on the substrate. In addition to the integrated circuits and the resistors, the circuit includes seven chip capacitors soldered onto the substrate. Some of the important considerations involved in the selection and reliability aspects of the hybrid circuit components are: (a) the quality of the substrate; (b) the surface structure of the thick film conductors; (c) the metallization characteristics of the integrated circuit; and (d) the quality of the wire bond interconnections.

TEM study of phosphorus-implanted pseudomorphic Si0.88Ge0.12 on Si(100)

1995 ◽  
Vol 53 ◽  
pp. 468-469
Author(s):  
N. David Theodore ◽  
Donald Y.C Lie ◽  
J. H. Song ◽  
Peter Crozier
Keyword(s):  
Integrated Circuits ◽  
Heterojunction Bipolar Transistors ◽  
Integrated Circuit ◽  
High Speed ◽  
Room Temperature ◽  
Strain Relaxation ◽  
Bipolar Transistors ◽  
Sige Hbt ◽  
Integrated Circuit Manufacturing ◽  
Microstructural Behavior

SiGe is being extensively investigated for use in heterojunction bipolar-transistors (HBT) and high-speed integrated circuits. The material offers adjustable bandgaps, improved carrier mobilities over Si homostructures, and compatibility with Si-based integrated-circuit manufacturing. SiGe HBT performance can be improved by increasing the base-doping or by widening the base link-region by ion implantation. A problem that arises however is that implantation can enhance strain-relaxation of SiGe/Si.Furthermore, once misfit or threading dislocations result, the defects can give rise to recombination-generation in depletion regions of semiconductor devices. It is of relevance therefore to study the damage and anneal behavior of implanted SiGe layers. The present study investigates the microstructural behavior of phosphorus implanted pseudomorphic metastable Si0.88Ge0.12 films on silicon, exposed to various anneals.Metastable pseudomorphic Si0.88Ge0.12 films were grown ~265 nm thick on a silicon wafer by molecular-beam epitaxy. Pieces of this wafer were then implanted at room temperature with 100 keV phosphorus ions to a dose of 1.5×1015 cm-2.

Micromechanics Measurements Applied to Integrated Circuit Microelectronics

1997 ◽  
Vol 473 ◽  
Author(s):  
David R. Clarke
Keyword(s):  
Integrated Circuits ◽  
Integrated Circuit ◽  
Fracture Resistance ◽  
Interface Fracture ◽  
New Techniques ◽  
Fracture Properties ◽  
Engineered Structures ◽  
Mechanical And Fracture Properties ◽  
Interconnect Lines ◽  
Metallic Interconnect

ABSTRACTAs in other engineered structures, fracture occasionally occurs in integrated microelectronic circuits. Fracture can take a number of forms including voiding of metallic interconnect lines, decohesion of interfaces, and stress-induced microcracking of thin films. The characteristic feature that distinguishes such fracture phenomena from similar behaviors in other engineered structures is the length scales involved, typically micron and sub-micron. This length scale necessitates new techniques for measuring mechanical and fracture properties. In this work, we describe non-contact optical techniques for probing strains and a microscopic “decohesion” test for measuring interface fracture resistance in integrated circuits.

Nanofabricated SiO2-Si-SiO2 Resonant Tunneling Diodes

2000 ◽  
Vol 631 ◽  
Author(s):  
J. G. Fleming ◽  
E. Chow ◽  
S.-Y. Lin
Keyword(s):  
Integrated Circuits ◽  
Integrated Circuit ◽  
Resonant Tunneling ◽  
Resonant Tunneling Diodes ◽  
Resonance Tunneling ◽  
Tunneling Diodes

ABSTRACTResonance Tunneling Diodes (RTDs) are devices that can demonstrate very highspeed operation. Typically they have been fabricated using epitaxial techniques and materials not consistent with standard commercial integrated circuits. We report here the first demonstration of SiO2-Si-SiO2 RTDs. These new structures were fabricated using novel combinations of silicon integrated circuit processes.

The Radio Probe™: A New Measurement Tool for High Speed Integrated Circuits

2005 ◽  
Author(s):  
Mark Kimball
Keyword(s):  
Integrated Circuits ◽  
Integrated Circuit ◽  
High Speed ◽  
Attenuation Factor ◽  
Cost Effective ◽  
Frequency Measurement ◽  
Single Frequency ◽  
Measurement Tool ◽  
Probe Design ◽  
Differential Measurement

Abstract This article presents a novel tool designed to allow circuit node measurements in a radio frequency (RF) integrated circuit. The discussion covers RF circuit problems; provides details on the Radio Probe design, which achieves an input impedance of 50Kohms and an overall attenuation factor of 0 dB; and describes signal to noise issues in the output signal, along with their improvement techniques. This cost-effective solution incorporates features that make it well suited to the task of differential measurement of circuit nodes within an RF IC. The Radio Probe concept offers a number of advantages compared to active probes. It is a single frequency measurement tool, so it complements, rather than replaces, active probes.

A Technique for Reliably Preparing Full-Length Metallographic Cross-Sections of Integrated Circuit Bond Wires

2006 ◽  
Author(s):  
Carl Nail
Keyword(s):  
Integrated Circuits ◽  
High Precision ◽  
Cross Sections ◽  
Integrated Circuit ◽  
Radiographic Analysis ◽  
Good Resolution ◽  
Metallographic Preparation ◽  
Bond Wires ◽  
Darkfield Imaging ◽  
Bond Wire

Abstract To overcome the obstacles in preparing high-precision cross-sections of 'blind' bond wires in integrated circuits, this article proposes a different technique that generates reliable, repeatable cross-sections of bond wires across most or all of their lengths, allowing unencumbered and relatively artifact-free analysis of a given bond wire. The basic method for cross-sectioning a 'blind' bond wire involves radiographic analysis of the sample and metallographic preparation of the sample to the plane of interest. This is followed by tracking the exact location of the plane on the original radiograph using a stereomicroscope and finally darkfield imaging in which the wire is clearly visible with good resolution.

Emerging Techniques for the Characterization of Nano-Mechanical Properties of Integrated Circuit Components

2008 ◽  
Author(s):  
Nicholas Randall ◽  
Rahul Premachandran Nair
Keyword(s):  
Mechanical Properties ◽  
Quality Control ◽  
Integrated Circuits ◽  
Integrated Circuit ◽  
Manufacturing Process ◽  
Solder Bumps ◽  
Initial Work ◽  
Circuit Components ◽  
Materials Used

Abstract With the growing complexity of integrated circuits (IC) comes the issue of quality control during the manufacturing process. In order to avoid late realization of design flaws which could be very expensive, the characterization of the mechanical properties of the IC components needs to be carried out in a more efficient and standardized manner. The effects of changes in the manufacturing process and materials used on the functioning and reliability of the final device also need to be addressed. Initial work on accurately determining several key mechanical properties of bonding pads, solder bumps and coatings using a combination of different methods and equipment has been summarized.

Enhancements of Non-contact Measurements of Electrical Waveforms on the Proximity of a Signal Surface Using Groups of Pulses

2002 ◽  
Author(s):  
Fenglei Du ◽  
Greg Bridges ◽  
D.J. Thomson ◽  
Rama R. Goruganthu ◽  
Shawn McBride ◽  
...  
Keyword(s):  
Integrated Circuits ◽  
Integrated Circuit ◽  
Signal To Noise Ratio ◽  
Electrostatic Force ◽  
Single Pulse ◽  
Electric Signal ◽  
Measurement Instruments ◽  
Cycle Times ◽  
Force Microscopy ◽  
And Performance

Abstract With the ever-increasing density and performance of integrated circuits, non-invasive, accurate, and high spatial and temporal resolution electric signal measurement instruments hold the key to performing successful diagnostics and failure analysis. Sampled electrostatic force microscopy (EFM) has the potential for such applications. It provides a noninvasive approach to measuring high frequency internal integrated circuit signals. Previous EFMs operate using a repetitive single-pulse sampling approach and are inherently subject to the signal-to-noise ratio (SNR) problems when test pattern duty cycle times become large. In this paper we present an innovative technique that uses groups of pulses to improve the SNR of sampled EFM systems. The approach can easily provide more than an order-ofmagnitude improvement to the SNR. The details of the approach are presented.

Analyzing the Impact of X-Ray Tomography on the Reliability of Integrated Circuits

2015 ◽  
Author(s):  
Halit Dogan ◽  
Md Mahbub Alam ◽  
Navid Asadizanjani ◽  
Sina Shahbazmohamadi ◽  
Domenic Forte ◽  
...  
Keyword(s):  
Integrated Circuits ◽  
Integrated Circuit ◽  
3D Imaging ◽  
Three Dimensional ◽  
Serial Sectioning ◽  
Promising Technique ◽  
Flash Memories ◽  
X Ray ◽  
3D Information ◽  
The Impact

Abstract X-ray tomography is a promising technique that can provide micron level, internal structure, and three dimensional (3D) information of an integrated circuit (IC) component without the need for serial sectioning or decapsulation. This is especially useful for counterfeit IC detection as demonstrated by recent work. Although the components remain physically intact during tomography, the effect of radiation on the electrical functionality is not yet fully investigated. In this paper we analyze the impact of X-ray tomography on the reliability of ICs with different fabrication technologies. We perform a 3D imaging using an advanced X-ray machine on Intel flash memories, Macronix flash memories, Xilinx Spartan 3 and Spartan 6 FPGAs. Electrical functionalities are then tested in a systematic procedure after each round of tomography to estimate the impact of X-ray on Flash erase time, read margin, and program operation, and the frequencies of ring oscillators in the FPGAs. A major finding is that erase times for flash memories of older technology are significantly degraded when exposed to tomography, eventually resulting in failure. However, the flash and Xilinx FPGAs of newer technologies seem less sensitive to tomography, as only minor degradations are observed. Further, we did not identify permanent failures for any chips in the time needed to perform tomography for counterfeit detection (approximately 2 hours).

Circuit Tracing on Integrated Circuit Using FIB Passive Voltage Contrast Effect

2015 ◽  
Author(s):  
Alexander Sorkin ◽  
Chris Pawlowicz ◽  
Alex Krechmer ◽  
Michael W. Phaneuf
Keyword(s):  
Electron Microscope ◽  
Integrated Circuits ◽  
Integrated Circuit ◽  
Metal Layer ◽  
Database System ◽  
Conventional Procedure ◽  
Sem Imaging ◽  
Voltage Contrast ◽  
Scanning Electron ◽  
Graphic Database

Abstract Competitive circuit analysis of Integrated Circuits (ICs) is one of the most challenging types of analysis. It involves multiple complex IC die de-processing/de-layering steps while keeping precise planarity from metal layer to metal layer. Each step is followed by Scanning Electron Microscope (SEM) imaging together with mosaicking that subsequently passes through an image recognition and Graphic Database System (GDS) conversion process. This conventional procedure is quite time and resource consuming. The current paper discusses and demonstrates a new inventive methodology of circuit tracing on an IC using known FIB Passive Voltage Contrast (PVC) effects [1]. This technique provides significant savings in time and resources.

Sign in / Sign up

Export Citation Format

Share Document