scholarly journals Evaluation of the effects of additives on the properties of starch-based bioplastic film

2021 ◽  
Vol 3 (4) ◽  
Author(s):  
Olugbenga O. Oluwasina ◽  
Bolaji P. Akinyele ◽  
Sunday J. Olusegun ◽  
Olayinka O. Oluwasina ◽  
Nelcy D. S. Mohallem
Keyword(s):  
Tensile Strength ◽  
Food Packaging ◽  
Surface Topology ◽  
Root Mean Square Roughness ◽  
Starch Solution ◽  
Dialdehyde Starch ◽  
Force Microscopy ◽  
Silica Solution ◽  
The One ◽  
Bioplastic Film

AbstractThe adverse environmental effects of petroleum-based packaging plastics have necessitated the need for eco-friendly bioplastics. Most bioplastics are starch-based and are not without drawbacks, hence there is the need for their properties to be improved. In this study, the effect of varying concentrations of dialdehyde starch and silica solutions on the physical, mechanical, biodegradable, surface topology, and thermal properties of the bioplastic films was examined. The additive concentrations were varied from 60 to 100%. The bioplastic films produced with dialdehyde starch solution recorded better moisture content (6.62–11.85%), bioplastic film solubility (4.23–7.90%), and tensile strength (1.63–3.06 MPa), against (11.24–14.26%), (7.77–19.27%) and (0.53–0.73 MPa) respectively for bioplastic films produced with silica solution. The atomic force microscopy analysis; root-mean-square roughness, kurtosis, and skewness revealed better miscibility and compatibility between the starch matrix and the dialdehyde solution than between the starch matrix and the silica solution. Bioplastic with added dialdehyde starch solution has better tensile strength and long biodegradability than that with silica solution. The research has demonstrated that bioplastic film produced with starch and dialdehyde starch solution has better properties than the one produced with starch and silica solution. The properties evaluation results of the bioplastic films thus demonstrated their aptness for food packaging applications. Graphic abstract

scholarly journals The Influence of Starch Origin on the Properties of Starch Films: Packaging Performance

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1146
Author(s):  
Zuzanna Żołek-Tryznowska ◽  
Alicja Kałuża
Keyword(s):  
Tensile Strength ◽  
Free Energy ◽  
Surface Free Energy ◽  
Food Packaging ◽  
Energy Surface ◽  
Free Energy Surface ◽  
Casting Method ◽  
Starch Solution ◽  
Film Properties ◽  
Starch Films

Starch films can be used as materials for food packaging purposes. The goal of this study is to compare how the starch origin influence the selected starch film properties. The films were made from various starches such as that from maize, potato, oat, rice, and tapioca using 50%w of glycerine as a plasticizer. The obtained starch-based films were made using the well-known casting method from a starch solution in water. The properties of the films that were evaluated were tensile strength, water vapour transition rate, moisture content, wettability, and their surface free energy. Surface free energy (SFE) and its polar and dispersive components were calculated using the Owens-Wendt-Rabel-Kaelbe approach. The values of SFE in the range of 51.64 to 70.81 mJ∙m−2 for the oat starch-based film and the maize starch-based film. The films revealed worse mechanical properties than those of conventional plastics for packaging purposes. The results indicated that the poorest tensile strength was exhibited by the starch-based films made from oat (0.36 MPa) and tapioca (0.78 MPa) and the greatest tensile strength (1.49 MPa) from potato.

scholarly journals Development of Intelligent Food Packaging with Rosa Sp Extract

2019 ◽  
Vol 9 (1) ◽  
pp. 5957-5961
Keyword(s):  
Tensile Strength ◽  
Physical Properties ◽  
Food Packaging ◽  
Petri Dish ◽  
Chitosan Solution ◽  
Starch Solution ◽  
Acid Base ◽  
Biodegradable Film ◽  
Color Changes ◽  
Different Temperatures

Rosa extract containing anthocyanin was integrated into starch-chitosan based film with glycerol as a plasticizer to develop a biodegradable film with acid base dye indicator. Anthocyanin is a pH sensitive compound that changes color when exposed to different pH. The color changes varied depends on the pH. A film aliquot was prepared by mixing rose extract, starch solution, chitosan solution with glycerol. The aliquot was casted in a petri dish at 40°C for 2days. Several tests were done to determine the biological, chemical and physical properties of the film. The tensile strength of the film was found to be in the range of 4.17MPa and 5.42MPa. The film was placed at 2 different temperatures for 4 days to determine the performance of the films and the effects of the temperature towards the film.

scholarly journals Preparation of Cellulose Films from Sustainable CO2/DBU/DMSO System

Polymers ◽  
2019 ◽  
Vol 11 (6) ◽  
pp. 994 ◽  
Author(s):  
Longming Jin ◽  
Jianyun Gan ◽  
Gang Hu ◽  
Long Cai ◽  
Zaiquan Li ◽  
...  
Keyword(s):  
Tensile Strength ◽  
Food Packaging ◽  
Solvent System ◽  
Light Transmittance ◽  
X Ray Diffraction ◽  
Force Microscopy ◽  
Cellulose Films ◽  
Atomic Force ◽  
Dmso System ◽  
Amorphous Structures

Cellulose films are regarded as sustainable materials having wide applications in food packaging, separation, etc. Their preparation substantially relies on sufficient dissolution. Herein, various celluloses adequately dissolved in a new solvent system of carbon dioxide,1, 8-diazabicyclo [5.4.0] undec-7-ene and dimethyl sulfoxide (CO2/DBU/DMSO) were made in to films using different regeneration reagents. The films regenerated from ethanol and methanol presented homogeneous and smooth surfaces, while those from 5 wt % NaOH (aq.) and 5 wt % H2SO4 (aq.) showed rough surfaces, as analyzed using scanning electron microscopy (SEM) and atomic force microscopy (AFM). The films regenerated from 5 wt % NaOH (aq.) and 5 wt % H2SO4 (aq.) rendered cellulose II structures, while those regenerated from alcohols had amorphous structures as evidenced using fourier transform infrared spectroscopy (FT-IR) and X-ray diffraction (XRD) results. The films made of microcrystalline cellulose had a good light transmittance of about 90% at 800 nm with a tensile strength of 55 MPa and an elongation break of 6.5%, while those from wood pulp cellulose demonstrated satisfactory flexibility with a tensile strength of 91 MPa and an elongation break of 9.0%. This research reports a simple, environmental, and sustainable method to prepare cellulose films of good mechanical properties.

The Reactive Formation of Diblock Copolymer at a Polymer/Polymer Interface and its Effect on Interfacial Structure

2000 ◽  
Vol 629 ◽  
Author(s):  
Jonathan S. Schulze ◽  
Timothy P. Lodge ◽  
Christopher W. Macosko
Keyword(s):  
Molecular Weight ◽  
Interfacial Structure ◽  
Root Mean Square Roughness ◽  
Radius Of Gyration ◽  
Interfacial Region ◽  
Force Microscopy ◽  
Amino Terminal ◽  
Polymer Interface ◽  
Atomic Force ◽  
Time Required

ABSTRACTThe reaction of perdeuterated amino-terminal polystyrene (dPS-NH2) with anhydrideterminal poly(methyl methacrylate) (PMMA-anh) at a PS/PMMA interface has been observed with forward recoil spectrometry (FRES). Bilayer samples were constructed by placing thin films of PS containing ∼8.5 wt % dPS-NH2 on a PMMA-anh layer. Significant reaction was observed only after annealing the samples at 174°C for several hours, a time scale at least two orders of magnitude greater than the time required for the dPS-NH2 chains to diffuse through the bulk PS layer. The topography of the interfacial region as copolymer formed was measured using atomic force microscopy (AFM). Roughening of the PS/PMMA interface was observed to varying degrees in all annealed samples. Furthermore, the extent of this roughening was found to depend on the PS matrix molecular weight. Reaction in the samples with a high molecular weight PS matrix resulted in a root mean square roughness approximately equal to the radius of gyration Rg of the copolymer. However, approximately twice as much roughening was observed in the low molecular weight PS matrix. This study reveals how the molecular weight of one of the phases can affect the rate of reaction at a polymer/polymer interface.

PEMANFAATAN LIMBAH KULIT DURIAN (Durio zibethinus) DAN KULIT CEMPEDAK (Artocarpus integer) SEBAGAI EDIBLE FILM

2014 ◽  
Vol 6 (1) ◽  
pp. 27 ◽  
Author(s):  
Desi Mustika Amaliyah
Keyword(s):  
Tensile Strength ◽  
Food Packaging ◽  
Raw Materials ◽  
Edible Films ◽  
Edible Film ◽  
Durio Zibethinus ◽  
Yield Result ◽  
Pre Treatment

Durian (Durio zibethinus) and cempedak (Artocarpus integer) peels waste are not used by the society. The research aim is to extract pectin from durian and cempedak peels and to formulate the pectin into edible films for food packaging. The research stages were first pre-treatment of durian and cempedak peels, pectin extraction, pectin drying, and  pectin application as edible films with concentration of 0%, 5%, and 15%. Based on this research it was concluded that pectin can be extracted from durian and cempedak peels with yield result of 27.97 % and 55.58 %, respectively. Edible film obtained has  similar characteristics between raw materials cempedak and durian peels. The higher concentration of cempedak peel  pectin increased the thickness, but decreased the tensile strength and elongation at a concentration of 15%. While in edible films from durian peel pectin, the higher concentration of pectin decreased the thickness of edible film on pectin concentration of 15%, lowered tensile strength and raised the edible film elongation.Keywords: waste, durian, cempedak, pectin extraction, edible film

Microstructure and mechanical property improvement of dissimilar metal joints for TC4 Ti alloy to Nitinol NiTi alloy by laser welding

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Yan Zhang ◽  
DeShui Yu ◽  
JianPing Zhou ◽  
DaQian Sun ◽  
HongMei Li
Keyword(s):  
Tensile Strength ◽  
Laser Welding ◽  
Mechanical Performance ◽  
Niti Alloy ◽  
Welding Process ◽  
Ti Alloy ◽  
The One ◽  
Fusion Weld ◽  
Welding Processes ◽  
Cu Interlayer

Abstract To avoid the formation of Ti-Ni intermetallics in a joint, three laser welding processes for Ti alloy–NiTi alloy joints were introduced. Sample A was formed while a laser acted at the Ti alloy–NiTi alloy interface, and the joint fractured along the weld centre line immediately after welding without filler metal. Sample B was formed while the laser acted on a Cu interlayer. The average tensile strength of sample B was 216 MPa. Sample C was formed while the laser acted 1.2 mm on the Ti alloy side. The one-pass welding process involved the creation of a joint with one fusion weld and one diffusion weld separated by the remaining unmelted Ti alloy. The mechanical performance of sample C was determined by the diffusion weld formed at the Ti alloy–NiTi alloy interface with a tensile strength of 256 MPa.

scholarly journals The Influence of Different Plasma Cell Discharges on the Performance Quality of Surgical Gown Samples

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4329
Author(s):  
Atif H. Asghar ◽  
Ahmed Rida Galaly
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Exposure Time ◽  
Electrical Characteristics ◽  
Cathode Fall ◽  
Treatment Efficiency ◽  
Performance Quality ◽  
Surgical Gown ◽  
The One

An experimental study was performed on a low-density plasma discharge using two different configurations of the plasma cell cathode, namely, the one mesh system electrodes (OMSE) and the one mesh and three system electrodes (OMTSE), to determine the electrical characteristics of the plasma such as current–voltage characteristics, breakdown voltage (VB), Paschen curves, current density (J), cathode fall thickness (dc), and electron density of the treated sample. The influence of the electrical characteristics of the plasma fluid in the cathode fall region for different cathode configuration cells (OMSE and OMTSE) on the performance quality of a surgical gown was studied to determine surface modification, treatment efficiency, exposure time, wettability property, and mechanical properties. Over a very short exposure time, the treatment efficiency for the surgical gown surface of plasma over the mesh cathode at a distance equivalent to the cathode fall distance dc values of the OMTSE and for OMSE reached a maximum. The wettability property decreased from 90 to 40% for OMTSE over a 180 s exposure time and decreased from 90 to 10% for OMSE over a 160 s exposure time. The mechanisms of each stage of surgical gown treatment by plasma are described. In this study, the mechanical properties of the untreated and treated surgical gown samples such as the tensile strength and elongation percentage, ultimate tensile strength, yield strength, strain hardening, resilience, toughness, and fracture (breaking) point were studied. Plasma had a more positive effect on the mechanical properties of the OMSE reactor than those of the OMTSE reactor.

Development of leftover rice/gelatin interpenetrating polymer network films for food packaging

2021 ◽  
Vol 10 (1) ◽  
pp. 37-48
Author(s):  
Sijia Li ◽  
Chun Shao ◽  
Zhikun Miao ◽  
Panfang Lu
Keyword(s):  
Food Packaging ◽  
Polymer Network ◽  
Raw Material ◽  
Interpenetrating Polymer Network ◽  
Waste Biomass ◽  
Practical Application ◽  
Water Contact ◽  
Force Microscopy ◽  
Atomic Force ◽  
Morphology Of Films

Abstract Waste biomass can be used as a raw material for food packaging. Different concentrations of gelatin (GEL) were introduced into the leftover rice (LR) system to form an interpenetrating polymer network (IPN) for improving the properties of the films. The structure and morphology of films were evaluated by Fourier transform infrared, scanning electron microscopy, and atomic force microscopy, which showed good compatibility between LR and GEL. The moisture content and oil absorption rate of IPN films were down by 105% and 182%, respectively, which showed better water and oil resistance than the LR film. In addition, increasing GEL concentration led to enhancement in the tensile strength of films from 2.42 to 11.40 MPa. The water contact angle value of the IPN films (117.53°) increased by 147% than the LR film (47.56°). The low haze of IPN films was obtained with the increment of the mutual entanglement of LR and GEL. The 30–50% GEL addition improved the water vapor barrier and thermal stability properties of the IPN films. This study highlights that LR as waste biomass can have a practical application in food packaging.

scholarly journals Nanostructural Arrangements and Surface Morphology on Ureasil-Polyether Films Loaded with Dexamethasone Acetate

Nanomaterials ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 1362
Author(s):  
Joao Augusto Oshiro ◽  
Angelo Lusuardi ◽  
Elena M. Beamud ◽  
Leila Aparecida Chiavacci ◽  
M. Teresa Cuberes
Keyword(s):  
Film Surface ◽  
Crystalline Phases ◽  
Essential Information ◽  
X Ray ◽  
Force Microscopy ◽  
Ether Oxygen ◽  
Dexamethasone Acetate ◽  
Poly Ethylene ◽  
The One ◽  
Poly Propylene

Ureasil-Poly(ethylene oxide) (ureasil-PEO500) and ureasil-Poly(propylene oxide) (u-PPO400) films, unloaded and loaded with dexamethasone acetate (DMA), have been investigated by carrying out atomic force microscopy (AFM), ultrasonic force microscopy (UFM), contact-angle, and drug release experiments. In addition, X-ray diffraction, small angle X-ray scattering, and infrared spectroscopy have provided essential information to understand the films’ structural organization. Our results reveal that while in u-PEO500 DMA occupies sites near the ether oxygen and remains absent from the film surface, in u-PPO400 new crystalline phases are formed when DMA is loaded, which show up as ~30–100 nm in diameter rounded clusters aligned along a well-defined direction, presumably related to the one defined by the characteristic polymer ropes distinguished on the surface of the unloaded u-POP film; occasionally, larger needle-shaped DMA crystals are also observed. UFM reveals that in the unloaded u-PPO matrix the polymer ropes are made up of strands, which in turn consist of aligned ~180 nm in diameter stiffer rounded clusters possibly formed by siloxane-node aggregates; the new crystalline phases may grow in-between the strands when the drug is loaded. The results illustrate the potential of AFM-based procedures, in combination with additional physico-chemical techniques, to picture the nanostructural arrangements in polymer matrices intended for drug delivery.

Sign in / Sign up

Export Citation Format

Share Document